Search Documents

By A. F. Brock

The cut-and-fill mining methods in use in the mines of The International Nickel Company of Canada Limited, at Falconbridge Nickel Mines Limited, in the Sudbury District, and at McIntyre Porcupine Mines Limited in the Porcupine District, are typical of the general cut-and-fill practice in both the base-metal mines and the gold mines in the Province of Ontario. The following pages describe the methods in use. HORIZONTAL CUT-AND-FILL STOPING Horizontal cut-and-fill stoping, as practiced in the mines of The International Nickel Company of Canada Limited, falls into two main classifications: (I) transverse cut-and-fill stoping, where ground conditions or wide ore bodies make it necessary to establish narrow stopes and pillars across the width of the ore body; (2) longitudinal cut-and-fill stoping where ore body widths and ground conditions allow safe mining of the full width of the ore body. Transverse Cut-and-fill StopiNg General Stoping Layouts Stope and Pillar Widths.—For transverse stoping, experience has indicated that narrow stopes and pillars, 27 ft. 6 in and 22 ft., respectively, are most satisfactory. These width are multiples of 5 ft. 6 in., which is the center to center dimension of a standard square set. Thus any stope, or block of stopes, can be readily converted from cut-and-fill to square set-and-fill if ground conditions should warrant such a change. Formerly, pillars were established 16 ft. 6 in. wide, the equivalent of the width of three square sets, with the intention of extracting the pillars by mining an overhand slice one set wide and an underhand slice two sets wide. However, subsequent experience proved that a two-set overhand slice is so much more efficiently mined than a one-set slice, and 22-ft. pillars have been made standard. Chutes.—The stope chutes are established on the longitudinal center line of the stopes and are spaced at 22-ft. centers from footwall to hanging wall. The footwall chute is usually from 5 to 10 it. from the footwall of the stope. It is offset where necessary at an angle of 52° and vertical chutes are carried from the offset at 22-ft. centers. In sections of the ore body where a flat hanging wall would cut off hanging-wall chutes within a few cuts of the sill, it has proved to be more economical to use temporary chutes or slushers, or both, for these first few cuts, rather than to el permanent chutes at the hanging wall.

Jan 1, 1946

By Fred C., Bond

IN CYANIDE milling, little attention has been paid to the effect of the viscosity of the mill solution on the extraction speed. The viscosity of the solution varies with the amount of dissolved salts present as impurities. These salts build up to a maximum depending on the character of the ore, the grade of cyanide used, the lime and salts added, and the impurities originally in the water. The viscosity will change from month to month and week to week as these factors vary; and that this variation affects the extraction is unquestioned, although methods for calculating it are lacking. The character of the ore is probably the most important of the four factors, as the amount of minerals present that are soluble in cyanide solution will vary constantly, and each variation affects the viscosity of the mill solution. When the cyanide consumption increases as the character of the ore changes, the viscosity of the solution will increase and the extraction will decrease, for the cyanide consumption is usually a measure of the impurities dissolved from the ore. In other words, as the difference between the total and free cyanide increases the extraction will decrease, other factors remaining constant.

Jan 1, 1926

By W. R. Ingalls

THE bases of the work by the committee whereof I am chairman were (1) the abolition of extra-lateral rights and (2) the preservation of the maximum of the existing laws. The matter of extra-lateral rights had been under prolonged discussion among mining men and up to the time when our com-mittee began its work (in 1917) the expression of opinion in every way whereby it could be made known -and those ways were extensive-was only a little short of being unanimous that extralateral rights ought to be abolished. I have not observed important evidence indicating a change of opinion on the subject since 1917. ABOLITION OF DISCOVERY LOGICAL Now, when it be decided that extralateral rights ought to be abolished, there can not be merely a simple change to that effect, but it is found that consequential changes are necessary all the way through the existing laws. Abolition of extralateral rights implies abolition of discovery as a prerequisite to location, for otherwise there would be no legal means for locating claims on the dip of a vein. Quite apart from this consideration, abolition of discovery as a prerequisite to location is supported by other good reasons. Among these are the occurrence of orebodies with no exposure on the surface and which often are hidden at great depth. A prospector who has reason to suspect the occurrence of such an orebody must have legal means for the location of a claim within which to explore, and obviously he may. not be able to make any discovery on the surface sufficient to locate and hold legally such a claim under the terms of the law as it stands at present. As a matter of fact, discovery as a prerequisite to location was abolished by common consent many years ago, not only for the reasons that I have given here-inbefore but also for others. It is highly desirable to revise the mining law in this respect, so that it will conform to the conditions of practice and not require people to perjure themselves in making locations, even if it be for praiseworthy purposes.

Jan 6, 1922

By AIME AIME

WHEN the War Production Board issued its order which will end the use of iron and steel in more than 400 familiar civilian articles, the list of those products formed a fascinating and homeric catalogue of the things we use. Articles for which iron and steel may not be used after a 90-day "tapering-off" period are as workaday as office machinery and as frivolous as cocktail shakers. Mostly they are smaller items-the smallest probably are phonograph needles but in the aggregate they will save tremendous quantities of the metal most needed to win the war. In total war there are no trifles. Interesting proof of this lies in the fact that by eliminating manufacture of blackhead squeezers we shall save 110,000 lb. of steel a year. Out of this steel we might have made four 155-mm. field pieces. We might have made a thousand 3-in. trench mortars, 4400 0.30-caliber machine guns, 55 16-in. shells, 110 200-lb. aerial bombs, or three 15-ton tanks with something left over to arm them.

Jan 1, 1942

Jan 1, 1958

By J. H. Anderson, G. A. Parks, B. K. Jindal, H. Leslie Bullock

H. Leslie Bullock (Engineering Consultant, Oak Park, 111.) — In reading over the paper, I find that I have no quarrel with the thoroughness of investigation of the points studied, but I am forced to question the selection of oxides from oxides as the subject of the investigation, the inclusion of silica gel as an example, and to question the validity of some of the conclusions. Separation of oxides from oxide, in minerals where the liberation of values is possible by grinding, are comparatively rare. Most oxides are only slightly soluble and the action of carbon dioxide or other acid forming ingredient in the air must be added to humidity to produce surface action. Silica gel is a very special synthetic substance in which the adsorption is determined by total surface, pore dimensions and temperature. Quartz is our most prevalent oxide and its action in electrostatic separation is far more sensitive to its three thermal transition points than to humidity.

Jan 1, 1968

By T. S. Lovering

GEOCHEMICAL prospecting extends the age-old method of searching out lodes with a gold pan and rationalizes the prospector's hunch that certain plants are associated with ore. It uses sensitive but cheap and rapid analytical methods to find the diagnostic chemical variations related to hidden mineral deposits. Exploration geologists can gain tremendous assistance from this new tool, although its optimum use is not simple. To bring out the geochemical pattern that reveals the presence of a hidden ore deposit with a minimum number of samples requires a combination of shrewdness, chemical knowledge, and exploration geology. The use of sensitive analytical methods for prospecting had its start in the 1930's in northern Europe, where Scandinavian and Russian geologists had some success in these early efforts. Very little geochemical prospecting was carried on in the United States at this time, and no sustained interest was manifest until the close of World War 11, when geochemical investigations were started by the Mineral Deposits Branch of the U. S. Geological Survey. The purpose of these investigations was to apply geochemical principles and techniques to surface exploration for mineral deposits. Both the research on analytical methods and the routine trace analyses for field investigations were at first conducted by a single group, but it later became apparent that the trace analyses could be done by men of less experience than that required for successful research on methods. For the past several years there have been two groups of chemists, and although their functions overlap, three of the chemists are chiefly concerned with research, while four to six other men make the trace analyses for field projects. The chemical investigations, as well as the field projects of the Geochemical Exploration Section, concern only those phases of the subject that are appropriate to a government organization; every effort is made to help private industry, but not to compete with it, in finding orebodies. The chief aim of the Section, therefore, is to develop new analytical techniques and publish the results promptly, to carry out field investigations of the fundamental principles of geochemical dispersion, and to field test promising- techniques under controlled conditions. Some routine geochemical exploration work is carried on in connection with DMEA loans, and in district studies where the project chief wishes geochemical information on certain areas for his report. It should be emphasized, however, that geologists of the Geochemical Exploration Section are primarily concerned with fundamental principles underlying the distribution, migration, and concentration of elements in the earth's crust. To facilitate the use of geochemical methods the USGS has published much information on its methods of analysis and has provided opportunities from time to time for qualified professional personnel to study these methods, to work in the USGS laboratory, or to attend demonstrations of the analytical techniques at the Denver Federal Center. Typical of the research carried on are the problems now being investigated: 1) Development of rapid and sensitive analytical methods suitable to the determination of traces of metals and other minor elements in various materials, such as rock, soils, plants, and water. At the present time attention is being concentrated on U, Bi, Cr, and Hg, and satisfactory rapid trace analytical methods are virtually perfected for U and Bi. Good methods are also available for: Cu, Zn, Pb, Ni, Co, As, Sb, W, Mo, Ag, Nb, Ge, V, Ti, Fe, Mn, S, and P. 2) The relation of geochemical anomalies in plant materials to the geochemical distribution of elements in soils surrounding the plant. 3) A study of the dispersion halos in transported sedimentary cover such as glacial drift and alluvium over known orebodies. 4) A study of the behavior of ore metals in the weathering cycle. 5) A study of the behavior of the ore metals during magmatic differentiation. This requires a study of the distribution of minor metals in fresh igneous rocks and their component minerals in a well established differentiation series and in adjacent country rock. 6) A study of the dispersion of metals in primary halos in the wall rock surrounding orebodies. 7) Regional and local studies of the metal content of surface and groundwater in mineralized and barren areas. Many field projects of the Mineral Deposits Branch also require the services of USGS chemists during their investigation of the geochemical environment of ore deposits. From the work that has been done certain general principles have emerged. Concentrations of an element that are above the general or background value of barren material are called positive geochemical anomalies or simply an anomaly, whereas values less than background are called negative anomalies. The anomalies most commonly investigated in geochemical prospecting are those formed at the earth's surface by agents of weathering, erosion, or surficial transportation, but more and more attention is being given to primary anomalies found

Jan 1, 1956

By Robert B. Fulton

Staurolite, an iron aluminum silicate mineral, is used industrially as a high value-in-use sand-blasting agent, as a premium grade foundry sand, and as the source of aluminum in portland cement manufacture in areas where the aluminum constituent is not economically available from shale or argillaceous limestone. It is produced by E. I. du Pont de Nemours & Co. as a coproduct in titanium mineral production in Florida where it was first recovered on a commercial scale in June 1952 from the Pleistocene sand deposit known as Trail Ridge. In the Trail Ridge deposit it comprises about one-fifth of the heavy minerals, the principal other heavy mineral constituents being ilmenite, leucoxene, rutile, zircon, kyanite, sillimanite, and tourmaline. Staurolite and the other silicate nonconductive heavy minerals are separated from the conductive titanium minerals on high-tension separators. The silicates are then separated from one another magnetically, the staurolite being relatively magnetic. In the total processing, 200 tons of raw sand yield 7 tons of heavy mineral concentrate from which about one ton of staurolite is recovered. This process yields staurolite concentrates of the characteristics given in Table 1. These concentrates are sold as three products with the size distribution of subrounded particles shown in Table 2. All three grades are used in sand-blasting for cleaning metal, for paint removal, and for cleaning buildings. Staurolite compares favorably with lower unit cost abrasives, such as boiler slags and mineral aggregates, in applications where the abrasive is used only one time and is not recovered. Because it is hard, fine, clean, and dense it can reduce blasting time, with less material reportedly being required [ ]

Jan 1, 1983

By AIME AIME

THE Committee on Elimination of Waste in industry came into existence from a speech in Washington by Mr. ,Hoover, in November, in which, he said: It is primary to mention the three-phase waste in production: first, from intermittent employment; second, from unemployment that arises in shifting of industrial currents; and third; from strikes and lockouts. Beyond this elimination of waste there is another field of progress in the adoption of measures for positive improvement in production.

Jan 1, 1921

By D. E. Wolfson, D. A. Reynolds, F. W. Smith

IN 1948 the U. S. Bureau of Mines began a three- phase program to evaluate the extent and quality of U. S. coking coal: 1) a factual appraisal of known recoverable reserves in beds of mineable thickness, 2) a study of preparation characteristics, and 3) a study of carbonization properties. A previous paper presented the methods used in assessing reserves.' Although this investigation is only partly completed, data on coking properties of the Pittsburgh district coals are now available. The results are presented in this article. When coals are selected for manufacture of metallurgical coke more factors must be considered than for any other major use, as no basic industry requires coal of such high quality and uniformity. This is particularly true in the Pittsburgh district, where blast furnace practice is based on use of cokes from high quality coals. Although it is true that inferior coals are carbonized in other industrial areas, both here and abroad, the Pittsburgh coals are the best economically obtainable in the required tonnages, even though they are not the most desirable for metallurgical use.

Jan 3, 1957

By Rebecca Mae Summer

Increasing urbanization and industrial activity require increased supplies of sand and gravel. This means expanded surface mining and despoiled land near population centers. Highly competitive land use demands justify serious consideration of premining planning for multiple land use and reclamation concurrent with mining. 1-5 Formulating solutions to environmentally and economically sound uses requires a comprehensive approach based on properties of the natural resource base--geology, soils, and water. A study of sand and gravel mining within Pleistocene-Holocene fluvial deposits in Colorado County. Texas [(Fig. 1)] illustrates how physical limitations imposed by the resource base are determined.6,7 Data from drillers, logs of water wells, test boreholes, field observations, and laboratory analyses are used to evaluate these physical controls. Knowledge of the thickness and composition of overburden aids in developing optimum reclamation and revegetation plans. Most of the overburden in the study area [(Fig. 2, 3)] is a clayey mud with variable amounts of silt and fine sand. A comparative textural analysis of overburden and native soil is used to assess changes incurred by mining and for evaluating other physical characteristics, e.g., ability to support crops, permeability. and shrink-swell potential. Textures are correlated with soil types found in the area [(Table 1)] to get an approximation of probable surface properties expected from these mined materials. Results of textural analyses [(Table 2)] indicate that separating topsoils from overburden during mining is not necessary because the range of overburden textures is about that of native soils. However, more data is needed on nutrient deficiencies to evaluate fertilizer requirements for successful revegetation.*6

Jan 1, 1979

By J. C. Jr. Vaughan

ALTHOUGH a considerable amount of practical importance attaches to systems involving gases and molten metals, little is known regarding the effects of alloy elements upon the solubility of gases in liquid iron. The solubilities of hydrogen1 and nitrogen2,3 in pure liquid iron are known and it has been shown that small amounts of silicon and aluminum3 exert only a small effect upon the solubility of nitrogen but greatly increase its rate of solution. This paper presents the results of a study of the Solubility Of nitrogen, at pressures approximately one atmosphere, in molten iron containing up to 1.5.5 per cent silicon.

Jan 1, 1939

By A. Lee Barrett

MINE power systems are quite different in many respects from those usually found in industrial plants. Wide areas are served, usually by a circuit which is connected continuously throughout the mine. In some mines one circuit may run for several miles. There are usually a small number of branch circuits involved considering the areas covered. In all mines circuits are sectionalized at approximately 2500 ft by means of switches. All, or at least most branch circuits, are sectionalized by manual switches. In some mines automatic sectionalizing gear is used to give automatic overload protection at various strategic points in the system. However at the present time this practice is by no means general. Circuit hazards in mine electric systems are much greater than those encountered in industrial installation. Falls of roof or coal form a prominent hazard which may break the wire and may cause ground faults or partial ground faults. Ordinarily electric cables in mines cannot be insulated, there- fore n fall can easily cause a short circuit. The humidity in most mines is greater than 95 pct and at many points the floor is wet and water may be dripping from the roof over insulators, increasing the difficulties at that point. All electrical circuits must be contained in the mine entries and space must also be provided for moving equipment and men. Consequently, because of the proximity of the power circuit to the locomotives and other moving equipment a considerable hazard is introduced. Mine haulage track is not always good so that wrecks are not unusual. A wreck frequently does consider- able damage to the power circuit. A ground fault frequently results in heavy arcing which may be sustained. If the damage to the circuit is mechanical it may mean that a trip of coal has wrecked and a great deal of coal dust could be thrown into the air as a result of the wreck. The arc resulting from the ground fault could ignite the coal dust and a mine explosion would result. A continued ground fault, even if high in resistance, also may ignite the coal which may be on the bottom of the entry and a mine fire may result. The fire hazard is one of the most serious hazards in any coal mine. Since the mine circuit is completely interconnected, any power interruption resulting from a fault seriously affects the whole operation. Unless the mine is completely sectionalized the whole mine will be shut down until the fault is located and the proper switches are opened to isolate the fault; even then large areas may still be without power if they are supplied by a single power circuit which may be opened in isolating the fault. Further, mine power is usually supplied from a relatively small number of substations and the fault may be on a stub feed circuit, in which case power cannot be restored until the fault has been cleared. Practice varies widely with respect to placement of substations. Usually they will be spaced from I to 2 miles in 500V operations, and at 1 mile intervals or less, in 250 V operation. Actual mining operations govern substation placements and no general rules can be followed.

Jan 1, 1948

By William L. Grube

PECIMEN preparation for electron metallography involves several steps, such as polishing, etching, replicating, mounting, and shadowing. Although each step must be done with care, the operation requiring the utmost attention is etching. Proper etching is important because the relief pattern developed on the surface of the specimen by the etchant, and reproduced as minute differences in thickness of the replica, determines entirely the amount of detail seen in the final micrograph. The characteristic colored stains, sometimes used in light metallography to simplify identification of certain microconstituents, cannot be tolerated because there is danger of introducing artifacts in the replicating operation. It is also quite difficult to remove plastic replicas from stained specimens. A suitable etchant for electron metallography must, therefore, in all cases exhibit a preferential attack upon each of the microconstituents present sufficient to result in a difference in surface elevation. When only two microconstituents are present, it is not too difficult to find a suitable etchant since their physical or chemical properties are generally sufficiently different to result in a marked difference in attack by the etchant. For example, picral (a saturated solution of picric acid in methanol used as an immersion etch) is a satisfactory etchant for the specimen shown in Fig. 1 consisting of iron carbide particles embedded in a ferrite matrix.'

Jan 1, 1952

By E. A. Holbrook

IT may be taken for granted that a mine official knows his duties, as outlined by the bituminous mining laws of the State, he knows how coal should be mined and transported, and he has judgment on any possibly unsafe condition in his mine. Certainly, if he is weak on any of these points, there are definite ways in which he can acquire the needed knowledge. If with this knowledge the mine official has the necessary practical experience to bring self-confidence, he stands before the world as a man who knows his job. There is, however, another side to his work, one not found in hooks, a side even that may not be learned at the face even though one spends a lifetime there. The actual duties a mine official knows and performs are the tangible and definite things about his work. There are other things which may be termed intangible, because they are hard to pin down and see, and. which appear to be of equal importance in successfully handling a job and which in time determine the very success of the company itself.

Jan 1, 1930

By Jack Fox

Three years ago we attended the V International Mining Congress in Moscow. This year we attended the VI International Mining Congress in Madrid. By almost any criterion, this was a most successful convention. There were 1717 registrants, not counting the ladies. I don't know how many of the latter there were, but they certainly made a welcome addition to the group. Once again, the International Organizing Committee put together a very impressive technical program which the Spanish National Committee backed up with a brand new Palacio de Congresos admirably equipped with simultaneous translation devices and an organization that provided an excellent social program, a tremendous set of post- meeting excursions, and very impressive opening ceremonies, entertainment and closing ceremonies. There was also an exhibit on the subject of Spanish and Spanish American mining history in the Palacio de Congresos.

Jan 1, 1970

By D. G. Peterson, W. J. Guay

The extraction of gold from refractory ores containing activated carbon and various types of carbon compounds is being done commercially for the first time at Carlin, Nev., by Carlin Gold Mining Co. Oxidation of the carbonaceous materials to CO and CO,- is accomplished by the introduction of chlorine into an aqueous pulp. The chlorine reacts with the limestone in the ore to form calcium hypochlorite which in turn reacts with the carbonaceous matter to form calcium chloride, CO, and CO.. Following the oxidation treatment the ore is cyanided in the conventional manner. For the first six months of operation the plant averaged 83% extraction at a feed rate of 500 tpd and a consumption of 28.4 lb chlorine per ton of ore which showed only 33.5% extraction by conventional cyanidation without the oxidation pretreatment.

Jan 1, 1974

By J. F. Myers, F. M. Lewis

The purpose of the mill tests reported herein, was to determine the relative power efficiency of fast and slow rod mill speeds on the ores of the Tennessee Copper Co. The tests were carried out at the Isabella Mill of the Tennessee Copper Co. under normal operating conditions. Every effort was made to keep the ore supply and other conditions constant, but it will be noted that some slight variation did occur. The open circuit 6 by 9 rod mill, and ore, used in these tests have been previously described.' Four motor drive pinions were available and the tests were performed in the following manner: each pinion was used to drive the mill for a period of one week. Constant sampling prevailed during the test run, and a composite sample for each speed test was made. Realizing that some slight liner wear took place during the four-week test-run, and that some slight variation of the ore may have taken place, a second and then a third series of four-week test-runs were made with the four different pinions. The screen analysis of each of the three-week run samples at the various speeds were composited and the results are shown in Table 2. The authors feel that the 22 weeks of operation consumed during these test-runs would represent fairly the effect of each mil1 speed. The data of line 37 show that within the error of sampling and plant operation, the tons of minus 65-mesh material generated per horsepower hour was the same at all four speeds. Obviously, rod and liner consumption could not be determined for each mill speed in so short a time. The rod load was maintained at a uniform level throughout the series of tests. The authors have operated rod mills at various speeds over the past several years, and it is their observation that rod consumption is directly proportional to the mill speed. Likewise, that the rod consumption per unit of work performed is a constant, providing that all other operating factors remain the same. It is a well known fact that the efficiency increases in a ball mill as the speed decreases. This is due to lateral segregation of the large and

Jan 1, 1950

By James Quigley

As the outcrop mines in the West developed into underground operations, systems of ground sup- port were gradually evolved. In the early coal mines there was little need for support except near the dirt line in portals, where stone masonry was common. Where the top was shaley or broken, native pine props with light cross bars and legs furnished enough support even in Utah's 25-ft coal seams. As depth of workings increased, roofs and backs of the same general nature as those near the surface became more and more unstable and required more and more support. Some coal airways show this tendency very clearly. From the surface down the same type of roof shows deterioration which an experienced eye can translate into a measure of depth under surface rather than change in rock characteristics. Rock bolts, developed by various companies and by the U. S. Bureau of Mines, have become an effective substitute for timber in sections of some metal and nonmetal mines formerly requiring excessive timber support, and further use of war surplus landing mats, chain link fencing, and a new punched channel developed by one of the steel companies has enabled other mines to operate deposits where costs of timber and lack of clearance for timber support would have prohibited mining. The block caving mines have made extensive use of reinforced concrete underground to achieve similar ends under difficult conditions. Steel sets are standard in many Bureau of Reclamation projects, although these are usually covered in with concrete to make the permanent structures the Bureau's reclamation projects require. But the use of steel in mining operations is limited and has been confined principally to the iron ore mines of Michigan, Wisconsin, and Minnesota. Some mines have installed used rail as posts, caps, and crossbars, but a rail section is not suited for load carrying, and used rails are generally brittle, having a tendency to fail without warning when overloaded.

Jan 7, 1959

Jan 1, 1934