Search Documents

The high-grade orebody at Miami was mined successively by top-slicing, shrinkage, stoping and under caving. The method described in this paper was developed to enable the low-grade orebody (36,000,000 tons assaying 1.06 per cent copper) to be mined at a low cost without further dilution of the grade. The method is clearly described and illustrated by drawings and photographs, and the original paper should be consulted as it is impracticable to abstract it, beyond noting that the mining cost is just under 40 cents per ton and the average grade of ore now being produced yields less copper than the mill tailing of 1915, the tons mined per day having increased from 4000 to 18,000 in the same period. Vertical and Incline Shaft Sinking at North Star Mine By Arthur B. Foote, Grass Valley, Calif. (Tech. Pub. No. 324: Class A. Metal Mining, No. 36) THE main shaft of the North Star mine is an inclined one following the main vein at an average dip of 26 deg., a vertical shaft intersects it at the 4000-ft. (incline) level, the incline continuing to the 6300-ft. level. At this point the vein was found to give out and a new vein, called the No. 1, was found to dip in exactly the opposite direction.

Jan 1, 1930

By William Reynolds

THIS paper deals with the results of a study of the application and development of mining machines for cutting out and removing dirt bands in bituminous coal beds. FACE PREPARATION When one or more dirt bands1 occur in a seam of coal, the problem of elimination of impurities becomes manifest. The degree of complete-ness to which these impurities are removed at the face has an important bearing upon labor costs, haulage costs and outside cleaning costs, and often the ash content of the product is markedly affected. Yet, because the present-day miner is paid for the number of tons he loads he often lacks interest in the quality of the coal. To insure a clean product, a system of penalties for dirty coal is enforced, but control of extraneous impurity content in the loaded coal is often inadequate and ineffectual when coal and banded impurity are shot as one. It seems only logical that to reduce the amount of impurities by proper face preparation before the men are permitted to load the coal is the most efficient method of preparation.

Jan 1, 1936

By T. A. Read, M. W. Burkart

The crystal geometry of the cubic-tetragonal interface after partial transformation of an indium-thallium alloy single crystal is described and a general theory is presented. The effects of applied stresses on this transformation are interpreted and the latent heat of transformation is obtained from observations of transformation under stress. A DIFFUSIONLESS phase transformation between face-centered cubic and face-centered tetragonal structures has been reported for the indium-thallium system by Bowles, Barrett, and Guttman1, 2 The transformation takes place at approximately 105 "C at 18 atomic pct Tl and 25°C at 23 pct Tl. In their study, Bowles, Barrett, and Guttman used poly-crystalline samples whereas in the present study single crystals were used to eliminate the transformation constraints imposed by adjoining grains. The use of single crystals made possible a comprehensive study of the effect of stress on the transformation. In the course of the work, it was possible to formulate a new method of analyzing dif-fusionless transformations (presented in this paper) which permits calculation of the geometry of the interphase interface from a knowledge of the crystal structures of the initial and final phases. The specimens were prepared from chemically pure thallium and 99.97 pct In which were weighed out to produce 3 to 4 grams of alloy of the desired concentration. The metal was placed in clean fused silica tubing, then melted, degassed and sealed under vacuum. (To obtain single crystals, it was found that both degassing and extreme cleanliness were essential.) Single-crystal specimens were grown by a modified Bridgman technique.8 pecimens were removed from the tube by dissolving the quartz in concentrated hydrofluoric acid which attacks the specimen very slowly. The specimen then was polished mechanically to produce four flat surfaces, electropolished, and annealed at 140°C for 48 hr. The electropolishing solution used was that described by Bowles, Barrett, and Guttman and the polishing was carried out on both the high and low temperature phases of the alloy. The high temperature polishing was done at 110°C with a stainless steel cathode. Visual Observation of the Transformation in Single Crystals A visual study of the transformation was made on specimens which had been electropolished in the high temperature phase. The specimens were supported on the stage of a metallograph by an electrically heated holder which contained an opening for observing the specimen. Visual evidence of transformation was found in the presence of an interface which separated the two phases. The interface plane defines the boundary of the phase undergoing transformation and manifests itself by the sharp change in angle between the surface of the specimen and the incident light at the juncture of the two phases. On slow cooling, well-annealed specimens transformed from the face-centered cubic structure to the face-centered tetragonal structure by the motion of a single plane interface which traversed the specimen from one end to the other. Upon heating, the interface moved back in the reverse direction. The interface could be started, stopped, or reversed at will. A temperature hysteresis of about 31/2oC was observed in the reversal of the interface. Holding an interface stationary caused it to disappear completely in most cases, whereas in other instances the interface became less distinct depending upon its orientation. The interface could be made to reappear by changing the temperature of the specimen. The low temperature tetragonal structure exhibits only the fine markings or subbands reported by Bowles, Barrett, and Guttman and is illustrated in Fig. 1. These subbands are twin-related. Back-reflection Laue patterns show the breakup of the cubic spots into pairs of spots corresponding to the twin orientations of the tetragonal phase.

Jan 1, 1954

By William L. Saunders

MANY members of the Institute, who participated in the visit made, during the Bethlehem meeting of February, 1906, to the shops of the Ingersoll-Rand Company, at Phillipsburg, N. J., inspected with interest the new Electric-Air drill, which the company had set up for the purpose of showing it in actual operation to American. mining engineers. At the request of the Secretary of the Institute, I promised at that time to prepare a paper for our Transactions, describing the construction and advantages of the machine. But such a paper would then necessarily have contained much that was only expected or claimed by the designers and manufacturers of the drill, and not yet incontrovertibly proved by varied and long-continued practice. However moderate such statements might have been, they would have given inevitably to the paper, to some extent at least, the air of a prospectus, rather than of a technical contribution. I therefore decided, with the Secretary's approval, to postpone the writing of the promised paper until it could set forth the results of adequate actual practice, as well as the latest details of construction, etc., based upon practical experience. That period has now arrived. The Electric-Air drill has been exhaustively tested in the field, under varied and arduous conditions and upon the hardest rocks. It is now fairly in the field; its merits and performances are matters of unimpeachable record, and its place among established competitors can be definitely determined. As a representative of the Ingersoll-Rand Co., as well as a member of the Institute, I may be permitted to add that my company, being largely interested in the manufacture of air-

Jan 9, 1907

By NORMAN D. FitzGkrald

IN 1942 the outstanding characteristic of the petroleum industry was the multiplicity of war-induced distortions in virtually every segment of the business. So devastating was the success of the Nazi submarine campaign along the shores of the western Atlantic and on transoceanic routes that within six months after our entry into the war petroleum rationing was necessary in the East Coast area. The conquest of the Netherlands Indies by the Japanese three months after the opening of the war in the Pacific cut off our normal sources of rubber, and in our first year of war nationwide rationing of gasoline had to be invoked to conserve rubber-borne transportation facilities. Meanwhile the oil industry faced the imperative necessity for rapid expansion in the output of aviation gasoline and later accepted the vast responsibility for developing a new industry. synthetic rubber manufacture. Probably no other essentially peacetime industry has been forced to make so many complicated adjustments, yet its response to its wartime obligations has been nothing short of dramatic.

Jan 1, 1943

By Richard E. Chism

The dry methods of assaying mercury-ores and other combinations of mercury all rest upon the volatility of this metal as a beginning. After the separation of the mercury in the form of vapor from the matrix upon which the assay is performed, the mercurial vapors are either condensed upon cold surfaces or received upon a gold plate into which the mercury is absorbed.

Jan 1, 1899

By W. A. Boyer, A. W. Beck

At the Morning mine of American Smelting & Refining Co. it was particularly important that there be a means of signaling the engineer from the moving cage in the shaft. Because of the shifting ground in which the shaft was located, buckling timber made it extremely difficult to keep a continuous bell line serviceable. In 1930 engineers considered a moving contact pantograph arrangement between the cage and two stationary messenger wires strung on insulators in the shaft compartment next to the cage. The idea was abandoned because falling material in the shaft and speed of hoisting made it difficult to maintain communication. Later in 1934 a manufacturing company was consulted about the use of an electric eye or a radio signal. As the shaft was located in a return air stream of nearly 100 pct relative humidity, there was too much fog for the electric eye to be used. The radio signal was considered, and it was believed feasible to generate electric static on the cage, locating a radio receiver at the top of the shaft, but the manufacturing company's research department was too busy to work on it at that time.

Sep 1, 1955

By David M. Parkes

This paper outlines the achievements to date at the British Columbia mine of Kaiser Resources Ltd. Almost one million raw short tons (855,000 metric tonnes) are now produced per year from a single monitor operation working 15 short shifts per week. Progress has been made in reducing the angle at which coal will flow in flumes by modifying the shape and the plastic linings. Improvements have been made in transporting coal from heading machines, and in the design of the present and future coal: water circuits. The development of hydraulic mining is still young and many improvements are being made.

Jan 1, 1976

By J. P. Newell, R. W Storey

This paper describes the development of a continuous float-and-sink process to produce coal low enough in ash content to be suitable for production of electrodes. The cleaned coal had a combined iron and silicon content of 0.239 pct. The efficiency of recovery was 84 pct. AUGER mining is a form of continuous mining in that it completely replaces with a one-cycle operation the older conventional cut, drill, shoot, and load method of mining. Relatively new, having been utilized only within the last few years, it is even more continuous in its production of coal than some other forms of continuous mining being practiced in this country today. There are at present coal recovery augers in operation working along strip-mined highwalls from the outside. This paper will deal with underground mining, specifically with an experiment which was carried out with a machine developed for this purpose. The location of this experiment was in Pike County in eastern Kentucky in the upper split of the No. 3 Elkhorn seam. Coal height was 32 in. and roof conditions were very bad, with 10 in. of soft draw slate coming down with every cut in conventional mining. The coal is high-grade bituminous, excellent for metallurgical coking. Underground auger mining fills a need for a method of recovering coal in thin seams, under bad roof conditions or in split seams. In many cases it might save money by eliminating the handling of excessive quantities of rock. In fact, if the coal can be recovered, as in the case of this experiment, without mixing with any impurities outside the seam, it may be possible to load or ship a satisfactory product with little or no preparation or cleaning expense. The need for some economical method for recovering coal from thin seams is becoming more pressing as the more profitably mined seams are exhausted. Basic Principles of Auger Mining The principles of the auger, or screw conveyor, have long been used in drilling small diameter holes for blasting and other purposes. These same fundamentals apply to large diameter drilling. However, considerably more attention was given to designing a cutting head that would not pulverize the coal and consequently would require a minimum of power to drive it. The head, as designed for this job, consists of a cylinder 25 in. in diam with steel bits set in 3 positions spaced around the forward rim. A conventional coal drill bit, at the head of a bursting cone in the center of the cylinder, trails the forward rim slightly, see Fig. 1. The bursting cone and auger connections are anchored to the cutter barrel by 3 arms spaced at 120". This head design proved to be very satis-

Jan 1, 1953

By J. P. Newell, R. W. Storey

This paper describes the development of a continuous float-and-sink process to produce coal low enough in ash content to be suitable for production of electrodes. The cleaned coal had a combined iron and silicon content of 0.239 pct. The efficiency of recovery was 84 pct. AUGER mining is a form of continuous mining in that it completely replaces with a one-cycle operation the older conventional cut, drill, shoot, and load method of mining. Relatively new, having been utilized only within the last few years, it is even more continuous in its production of coal than some other forms of continuous mining being practiced in this country today. There are at present coal recovery augers in operation working along strip-mined highwalls from the outside. This paper will deal with underground mining, specifically with an experiment which was carried out with a machine developed for this purpose. The location of this experiment was in Pike County in eastern Kentucky in the upper split of the No. 3 Elkhorn seam. Coal height was 32 in. and roof conditions were very bad, with 10 in. of soft draw slate coming down with every cut in conventional mining. The coal is high-grade bituminous, excellent for metallurgical coking. Underground auger mining fills a need for a method of recovering coal in thin seams, under bad roof conditions or in split seams. In many cases it might save money by eliminating the handling of excessive quantities of rock. In fact, if the coal can be recovered, as in the case of this experiment, without mixing with any impurities outside the seam, it may be possible to load or ship a satisfactory product with little or no preparation or cleaning expense. The need for some economical method for recovering coal from thin seams is becoming more pressing as the more profitably mined seams are exhausted. Basic Principles of Auger Mining The principles of the auger, or screw conveyor, have long been used in drilling small diameter holes for blasting and other purposes. These same fundamentals apply to large diameter drilling. However, considerably more attention was given to designing a cutting head that would not pulverize the coal and consequently would require a minimum of power to drive it. The head, as designed for this job, consists of a cylinder 25 in. in diam with steel bits set in 3 positions spaced around the forward rim. A conventional coal drill bit, at the head of a bursting cone in the center of the cylinder, trails the forward rim slightly, see Fig. 1. The bursting cone and auger connections are anchored to the cutter barrel by 3 arms spaced at 120". This head design proved to be very satis-

Jan 1, 1953

By O. N. Carlson, H. A. Wilhelm, J. M. Dickinson

On the basis of microscopic studies, melting-point observations, and X-ray analyses, a phase diagram is proposed for the Cb-V system. A complete series of solid solutions is formed with a minimum in the solidus at 1810°C near 35 wt pct Cb. No compounds or intermediate phases were found in the system above 650°C. THERE is an ever increasing need for better structural metals and alloys for use in nuclear reactors. In addition to the normal properties of engineering structural materials, such as high temperature strength, resistance to corrosion, and fabric-abil~ty, the nuclear properties of the material must be considered. In a nuclear reactor it is important to conserve neutrons, so a material which removes these neutrons from the reaction excessively is considered to have unfavorable nuclear properties. In nuclear-reactor design the engineer must have nuclear as well as other data available on alloys in order to make a wise selection of materials. Due to the fact that many of the common structural materials have undesirable nuclear properties, it is vital that new alloys of metals having more favorable nuclear properties be investigated. Columbium and vanadium are both high melting metals, both exhibit resistance to chemical attack, and no great difficulty is encountered in fabricating them into desired shapes. With proper treatment both metals can be cold rolled extensively without failure. In addition they have desirable nuclear properties for certain types of reactors. Therefore, the alloys of columbium and vanadium should be of interest in the atomic energy program. Since an alloy-development program is enhanced by a knowledge of the phase equilibria of the components, this investigation was undertaken to establish the phase diagram for the Cb-V system. According to the Hume-Rothery rules for alloying,' the chemical similarity, crystal structure, and atomic-size factor are favorable for a complete series of solid solutions for this system. Both elements are in the same family of group V of the periodic table and thus are quite similar chemically. The crystal structures of columbium and vanadium are compatible for extensive solid solubility, since both have body-centered-cubic structures. The atomic diameters of columbium and vanadium are 2.85 and 2.62Å, respectively. This difference of slightly more than 8 pct is well within the 15 pct maximum difference allowed for extensive solid solubility. Experimental Procedures Source of Materials: Columbium powder and sheet trimmings were obtained from the Fansteel Metallurgical Corp. According to the manufacturer the metal contains less than 1 pct impurity. An analysis of the metal showed approximately 1800 ppm C in the powder while the sheet trimmings contained less than 500 ppm C. Spectrographic analysis showed minor amounts of Ca, Cr, Fe, Mn, Si, Ti, V, and Zr in both forms of the columbium. No commercial source of vanadium having the ductility and purity desired was available to the authors at the beginning of this investigation. As a result, all of the vanadium used in this study was prepared by the bomb reduction of vanadium pen-toxide with calcium employing the method reported by Long.' Yields of massive vanadium normally were about 80 pct. Chemical analysis of the vanadium prepared in this manner showed the presence of 200 to 500 ppm N and 800 to 1000 ppm C. Minor amounts of Ca, Fe, Mn, Si, Zr, Cr, and Cb were detected by spectrographic analysis. This vanadium metal was ductile and was cold rolled into 5 mil sheet. Annealing was not necessary during this rolling and the metal retained its cold-rolling characteristic after are-melting. Preparation of Alloys: The Cb-V alloys were prepared by melting pieces of vanadium sheet togethel-with columbium in the form of sheet or pellets of powder. The melting was carried out under argon in conventional arc-melting equipment employing a tungsten electrode and a water-cooled copper crucible. Each alloy was remelted three or four times, inverting the alloy after each melting in order to assure complete mixing. Alloys normally were obtained as round flat disks, weighed approximately 70 grams, and had roughly the shape of a disk 1 1/2 in. in diameter and 1/4 in. thick. Half of each alloy

Jan 1, 1955

By Robert Kinzie

WHEN Mr. Cameron, the President of the Santa Cruz Portland Cement Co., returned from Europe in 1929, he brought first-hand infor-mation about a very versatile type of hydraulic cement. It was not a new cement, many articles having been written about it in foreign journals, but in this country the record of this type of cement had been either neglected or minimized. Using local materials, and applying the information brought back by Mr. Cameron together with many data in numerous publications, the Santa Cruz Portland Cement Co. developed the Santa Cruz high-silica cement. This cement is manufactured by grinding with portland cement clinker a properly calcined mixture of siliceous material and lime. It has all the utility of portland cement, together with an increased resistance to the destructive action of many aggressive solutions. To explain the necessity for the development of a cement having these characteristics, the history of hydraulic binding materials may be reviewed briefly. The materials used as binding media by primitive people were mud, lime, gypsum and bitumin. Due to its utility, ease of preparation, and its common occurrence, lime was the most widely used. Fat lime, when used by itself or with an inert sand, hardened only on the outside surface, where the carbonate was formed by absorption of carbon dioxide from the air, while, the interior of the mortar remained soft. It was quite early discovered that the incorporation of proper siliceous material with the lime increased its ability to harden, and for this purpose various natural siliceous powders were used, such as puzzo-lana in Italy, trass in what is now Germany, and santorin in Greece. These powders reacted with the lime forming a permanent cement and rendered unnecessary the access of carbon dioxide to the mortar.

Jan 1, 1934

By E. H. Crabtree, T. C. King

THE ferrosilicon grinding unit at the Central Mill of the Eagle-Picher Mining & Smelting Co. near Picher, Okla., was completed in March 1947. The object of the plant was to grind pigs of ferrosilicon, having a size of approximately 1 ½ by 4 by 12 in. and an analysis of 85 pct Fe and 15 pct Si, to approximately 100 mesh by crushing and wet grinding in a ball-mill classifier circuit. The minus-loo mesh ferrosilicon had formerly been purchased, and was used as medium in the heavy media process for treatment of lead-zinc ores. From the standpoint of dollars and cents, the cost of minus-100 mesh ferrosilicon was roughly $40.00 per ton more than pigs of the corresponding alloy delivered to the mill. Estimated wet grinding costs were considerably below this figure. The possible saving in cost of make-up medium for the cone plant was particularly attractive since, at that time, the plant losses averaged over four tons of minus-100 mesh ferrosilicon per day. Aside from the probable saving on the grinding charge, the need for such a unit was twofold. First, periodic fluctuations in the differential between the top and bottom densities of the cone were thought to be detrimental to metallurgy. There was little doubt that an intermediate differential existed at which the heavy media separation was most efficient, representing a compromise between concentrate grade and tailing loss. Furthermore, if a finer, but considerably cleaner, medium could be obtained, there was the possibility that the differential could be decreased without increasing the viscosity, or conversely, the viscosity of the medium decreased without increasing the differential. Preliminary to experimental work aimed at pegging the cone differential and circulating medium viscosity at whatever values were found to be most efficient, it was essential to have control over both the non-magnetic content of the medium and the particle size of the contained ferrosilicon. The latter was possible by means of a grinding unit at the mill. Second, whereas the ferrosilicon alloys are made by a number of manufacturers, only two, to our knowledge, grind it in any quantity for use in heavy media plants. For all practical purposes, the Central Mill was limited to one source of supply, a particularly vulnerable position. In case the supply was cut off, it was thought that pigs of the 85 pct Fe, 15 pct Si alloy could be obtained elsewhere, providing means of grinding them was available. There was no published information available covering wet grinding of ferrosilicon. Dry grinding in batch mills and in continuous mills with air classification was being practiced, but the cost of grinding was excessive and the dust condition objectionable. It appeared that primary and secondary crushing was no particular problem, providing heavy duty equipment was used;

Jan 1, 1947

By Werner Langguth

The modern process and plant for the precipitation of gold from chlorine solutions, by sulphurous acid gas and hydrogen sulphide, differ materially from the older methods of precipitating with sulphate of iron. The chemical process and its applicability, as carried out in the Golden Reward chlorination-works at Deadwood, S. D., was described and discussed in the Engineering and Mining Journal, of New York, for February 14, and March 21, 1891. I purpose to give, in this paper, the details of construction from a general standpoint—the particular arrangement, most suitable to each case, depending, of course, upon local conditions. The accompanying sketch shows the arrangement. The plant consists of a wooden, lead-lined tank, in which the chlorine solution is precipitated; apparatus for the production of the precipitants, sulphurous acid and hydrogen sulphide; and a pressure-tank and filter-press for the collection and filtration of the precipitated gold-sulphides. These parts and arrangements are, in general, those which I employed in the Deadwood chlorinationworks, and which have proved practically successful, more than $100,000 worth of gold having been already precipitated by this method. In the construction of the generator and pressure-tank I have made, however, a few slight changes. 1. The Precipitating-Tank. The exact dimensions of this tank are not of much importance. A horizontal area of 10 x 12 feet and a height of 12 feet, holding about 7000 gallons of solution, is a good size. As the amount of attention and care required to precipitate the solution in a precipitatingtank is independent of the size of the vessel, there is economy in tanks of large capacity. Square tanks are more advantageous than round ones, because they need less floor-space, and at the same time are cheaper in construction. These tanks are made of common 2inch pine boards and 12 x 12-inch timber. They are well-bolted,

Jan 1, 1893

By Harold L. Walker

ENGINEERING educators have recently been discussing the advisability of extending the undergraduate curricula to five or six years, and a plan has also been proposed requiring a preliminary period of study in the liberal arts college before admission to the engineering college. Extension of the undergraduate curricula has been suggested as a means of more fully covering the subject matter in the major field of study. Interest in this proposed plan of requiring a preliminary period of study in the liberal arts college has been heightened through a bill recently introduced in the legislature of the State of New York. This plan intends to give a more professional status to engineering, and credit for these additional years of study would be allowed to those engineers applying for professional licensure. As a result of the interest in engineering curricula and due to the impetus given by these proposed plans a general reexamination of curricula has been conducted by a large number of schools with the stated purpose of determining if the present curricula are meeting the aims and scopes of engineering education.

Jan 1, 1940

By S. Yukawa, M. J. Sinnott

A high resolution autoradiographic study of the diffusion of a nickel isotope (NP3) into copper in the temperature range of 650° to 925°C, with particular emphasis on grain boundary diffusion, has been made. The extent of grain boundary diffusion is a function of the grain boundary angle and the diffusion temperature. The ratios of the grain boundary diffusion coefficient to the lattice diffusion coefficient ranges from 104 to 105. The activation energy for grain boundary diffusion decreases with increasing grain boundary angle. STUDIES and reviews&apos;-8 of metallic diffusion have indicated that grain boundary diffusion is a common phenomenon but quantitative studies of the many variables involved are not numerous. The present work was concerned with determining the influence of the crystallographic orientation of the grain boundaries and the temperature on the extent of boundary diffusion of nickel into copper. The study involved essentially three steps: 1—the production of grain boundaries of known crystallographic orientation, 2—the determination of the extent of diffusion into the boundaries, and 3—the analysis of the resulting data in terms of the usual diffusion concepts. The grain boundaries investigated approximated the simple tilt variety having l° of freedom. They were produced by controlling the solidification from a melt of Cuprovac (a high purity vacuum-melted copper obtained from Vacuum Metals Corp.) of a pair of seed crystals so that the bicrystals of copper produced had a common <100> axis. By rotating one seed crystal relative to the other, a simple tilt boundary was produced. The angle of rotation between the two crystals is the grain boundary angle 8, or what is sometimes termed the misfit angle. In all, some 16 boundaries ranging from 2" to 72" in 5" to 10" steps were investigated. The crystallographic orientations were measured with the use of both X-ray and optical goniometric techniques. The <100> axes in the crystals were found to be parallel within 2" to 3" with the exception of one crystal (8 = 12") in which the axes were 6" from being parallel. All bicrystals showed evidences of sub-grain structures. Laue analyses showed that these subgrains differed in orientation up to a maximum of 2". Because of these variations, and some curvature in the boundaries, the grain boundary angles listed are actually average values and deviate from the 1 o of freedom boundaries. The stripping film technique of high resolution autoradiography was used to detect the diffusion of the nickel isotope into the grain boundaries of the bicrystals of copper. Kodak experimental permeable stripping film with an emulsion layer 5 u thick

Jan 1, 1956

By E. V. Howard

During the recent expansion of precipitate copper production at the Chino Mines Division of Kennecott Copper Corp., Santa Rita, N. Mex., local studies of the dump leaching process were intensified. As these studies progressed, it became apparent that a reliable method for locating leach solutions within the dump was required, since the contact between the leach solutions and the copper-bearing ma.teria1 determines recovery. In the past, the problem of determining leach solution contact has been attacked by various methods, including destructive testing (dump dissection), indirect observation (such as chloride or dye tracers) and mathematical or laboratory model studies, but they have not proved completely satisfactory. The investigation of methods for in situ observation of leach solutions led to consideration of radiation logging in drillholes, which are subsurface techniques used in petroleum exploration and development for locating fluids and measuring porosity. A significant advantage of radiation logging is that, unlike other types of logging, measurements may be made in cased holes, since gamma rays and neutrons will penetrate steel and cement. Three techniques are currently used at Chino: Natural gamma ray logging; neutron-neutron, or moisture logging; and gamma-gamma, or bulk density logging.

Jan 4, 1968

By N. J. Gran, W. R. Opie

HYDROGEN in molten aluminum and aluminum alloys, which precipitates during cooling and solidification, is the principal cause of pin hole porosity in ingots and castings. Much attention has been given to determining the effect of temperature and pressure on the solubility of hydrogen in pure aluminum, but little data are available on hydrogen solubility in aluminum alloys. This investigation was undertaken to check results reported for pure aluminum and to show the effect of silicon and copper additions on the amount of hydrogen contained by molten alloys. Previous determinations of the solubility of hy-drogen in molten pure aluminum are plotted in fig. 1. The most reliable data appear to be those of Ransley and Neufeldl and of Baukloh and Oester-len.&apos; The latter authors also report some results on the effect of copper and silicon additions. Up to 6 pct these elements decrease the solubility of hydrogen quite rapidly, with a definite minimum noted at 6 wt pct for both copper and for silicon, although no reason is apparent for these minima. Experimental Procedure The solubility of dry hydrogen in pure aluminum, aluminum-silicon, and aluminum-copper alloys was determined by the method of Sieverts.8 This consists of determining the volume of the gas system above the molten metal at a given temperature and pressure by using an insoluble gas. This volume is referred to as the "hot volume." The system is then evacuated and the soluble gas is introduced at the same temperature and until the same pressure is reached. It is necessary to introduce enough of the soluble gas to fill the space above the metal plus the soluble amount. The difference in the volume of soluble gas and the "hot volume" is the solubility. The accuracy of solubility measurements by the Sieverts&apos; method is primarily depend-

Jan 1, 1951

By J. L. Christie, R. H. Leach

SO much has been written recently about the use of silver to replace scarce metals that certain facts about silver and its uses should be of interest. Figures for the production and use of silver, taken from the Handy & Harman annual reviews of the silver market, are given in Table 1. It will be seen that the rate of production has remained fairly constant and has been affected in recent years by the production of base metals, of which silver is a by-product. In each of the years 1937, 1938, and 1939, the U.S. Government acquisitions alone exceeded the entire world production, the difference, of course, being made up by imports of previously accumulated stocks. In 1940 and 1941 the U. S. Government acquisitions plus the United States and Canadian uses in the arts and industries exceeded the Western Hemisphere production. The U.S. Government pays a premium price for silver newly mined in the United States, at present 71.11c. compared with the price of 35&apos;/8c. for foreign silver, with the result that the current U. S. production is not used commercially for the arts and industries. At the time this is written (June 1942) there is much uncertainty as to the future effect of this situation.

Jan 1, 1942

By Robert B. McCormick

THE major use for quartz crystal is in the manufacture of radio oscillator plates and telephone resonator and filter crystals. Quartz crystal is also cut and polished as a semiprecious gem stone, particularly in the colored varieties (amethyst, Brazilian topaz, and others), and often is carved into various objects of art. Prisms, wedges, lenses and other optical parts often are made of quartz crystal, usually for special- purpose instruments. Chips and small clear crystals below 100 grams in weight, called “lascas” by the trade, are the raw material for fused quartz products. HISTORICAL BACKGROUND The Greeks believed quartz to be permanently frozen water and therefore called it krustallos, which, literally translated, means clear ice; but ages before their civilization, prehistoric man had crudely cut and polished crystals for rough charms and ornaments. About 2000 B.C., the Egyptians brought the art of cutting quartz to a high level. While there are earlier examples of crystal art that have great value, working in crystal during that period became a means of artistic and religious expression that has endured through the ages. Art museums and private collections throughout the world contain many priceless pieces. They include findings from the tombs of the earliest Egyptian rulers, as well as magnificent art objects in both clear and colored crystal encrusted with silver, gold, enamel, and precious gems of oriental and European workmanship. Pierre Curie first measured the piezoelectric effect of quartz, in 188 1, by placing a weight on the surface of a quartz crystal and measuring the resulting electrical charge, which he found was proportional to the weight applied. The following year the inverse piezoelectric effect was proved by the Curies. By applying a voltage to a piece of quartz, a measurable physical displacement occurs. The first practical application of this effect was the construction of a bimorph unit to measure voltage by measuring the amount of the displacement of the end of the bimorph. The piezoelectric properties of quartz crystal remained largely a laboratory curiosity until World War I, when a supersonic device for

Jan 1, 1949