Search Documents

By C. H. Jr. Herty

FEW subjects have attracted the attention of metallurgists more than ,oxygen in steel. From the days of Mushet and Ledebur interest in this subject has been increasing, and as additional knowledge has become available, the problem has naturally grown more complex. Instead of using the simple term "oxygen" we now distinguish between iron oxide, silicates of various kinds, oxysulfides, oxygen as gas and oxygen in solid solution in steel. There are five general methods for determining oxides in steel: hydrogen reduction;, vacuum fusion; various wet-extraction methods, including electrolytic methods; methods depending on volatilization of the iron away from the oxides; and metallographic methods. For oxygen in solid steel each of these methods has both advantages and disadvantages. The hydrogen-reduction method is of no use on steels above about 0.20 per cent. carbon;1 furthermore, it gives only FeO and possibly some MnO. The vacuum-fusion method2 is expensive and gives total oxygen, with the exception of some A1203, and does not differentiate between the various oxides in which the oxygen exists. Most of the wet-extraction methods' give only the more insoluble oxides Si02 and A1203, though the iodine method gives MnO to an uncertain degree (information that may be more misleading then no information

Jan 1, 1930

Jan 1, 1957

By Frederick T. Fischer

The New Jersey Zinc Company began a program of exploration in Middle Tennessee in 1964. The target horizon of the exploration project has been the Knox Dolomite which is a low-yield aquifer over nearly the entire Central Basin of Tennessee (1). With the exception of a few hundred acres in the Wells Creek and Flynn Creek disturbances (astroblemes?), the Knox Dolomite in Middle Tennessee is known only in subsurface. In January of 1969, New Jersey Zinc announced the discovery of a major zinc deposit near Elmwood, southeast of Carthage. This is on the northeastern flank of the Nashville Dome where the nearly flat-lying beds have an average eastward slope of about 50 feet per mile. The anticipated development of a mining situation has emphasized the significance of hydrologic relationships in the region as a whole and especially in the Elmwood area. These relationships affect several areas of concern which ma be generally grouped into two broad classes; i. e. , (1) Problems of a Public Nature - involving the prevention of the contamination of potable aquifers, the prevention of the contamination of surface waters, the prevention of the capture of presently utilized water, etc.; and (2) Problems of Mining Economics - involving pumping capacity and costs, the possible need for equipment of special composition, underground environmental conditions, etc. Exploration drilling in Middle Tennessee has contributed additional information about the Knox aquifer and

Jan 1, 1970

By Tsuyoshi Miyashita

Onahama Refinery of Ryoho Recycle Company employs the electrothermic process for producing marketable zinc oxide from steelmaking dusts. The process comprises washing, filtration, drying, sintering and furnacing. Fume from the sinter machine is treated hydrometallurgically to recover zinc, cadmium and lead.

Jan 1, 1976

OBSERVERS in more than negligible number appear to believe that the achievements of engineers during the last generation have been an affliction rather than a blessing to society. Quite accurately they perceive that scientific progress and technologic advance have reduced to a fraction-often a small fraction-the amount of manual effort required to accomplish a given unit of useful work. They have seen men, as a consequence, deprived of employment in a particular industry; and this so-called technological unemployment they have denounced as inimical to the workers and consequently to the whole social order in progressive nations. To those who subscribe to this thesis the story of the Porphyry Coppers may not make palatable reading, for it is an amazing record of engineering and technologic achievement. But to those others who take the longer and broader view that economic and social progress cannot enduringly lag far behind advance in the realm of science and engineering; and that any improvement in the means and method of doing essential things eventually must make the world a better place in which to live; to these the record of the development of these great mines can- not but be a source of delight. It is an outstanding example of the advantages of mass production coupled with the fruits of scientific research and inventive genius. More, it reflects the pioneer spirit, the initiative, the self-reliance, the independence of thought and action that are traditional with the mining engineer. The word porphyry is a geologic term, the significance of which will be elaborated in later chapters. The essential characteristics of the deposits that are universally, if not quite

Jan 1, 1933

By Ralph H. Sweetser

BENEFICIATION of iron ores from the blast-furnace point of view means more than the usual enrichment of the iron contents by the removal of a large part of the clay, carbonic acid gas, silica, or moisture of the natural ore; it includes all these, but it also embraces several other mechanical .processes made , necessary by the exacting requirements of present-day blast-furnace practice. The increasing use of iron- bearing by-products, to as much as a third or more of the total ore burden, has introduced still another series of processes for improving the blast-furnace ore burden. As we look back over the past three decades of blast- furnace practice 'in. this country, we see that many of the blast-furnace troubles were directly due to lack of proper preparation of the iron ore burden,, and we realize that beneficiation in one form or another would have remedied the trouble. This was particularly true in the smelting of magnetic iron ores, where run-of- mine ore included such big lumps of 'magnetite along with rich fines that the furnace operations were greatly retarded and control of the furnace such as is usual today, was completely unknown.

Jan 1, 1930

Jan 1, 1918

By D. S. Newton

Introduction Historically the production of zinc dust has been based upon residual and secondary zinc. Using horizontal retorts filled with diecasting scrap, galvanizers drosses and sweater billets, dust has been produced by condensation into static condensers on a 24 hour cycle. Although fairly flexible as regards input materials the process is not amenable to close control of the product, is labour intensive and unless carefully run can cause fume problems. With a steadily increasing demand for zinc dust of consistent properties and higher quality there is a demand for an improved method of manufacture in which dust can be produced continuously and which is capable of close control thus ensuring a minimum amount of oversize or unsaleable material. The Process in use in the works of Imperial Smelting Corporation (Alloys) Ltd. in England, and in Canada and Holland, satisfies the criteria stated above, and has proved to be easy to control with a minimum labour demand.

Jan 1, 1970

By Arthur M. Miller

FROM the time of its establishment in 1933, the Tennessee Valley Authority has been active in the field of phosphates. Under the T.V.A. Act it has a broad Congressional mandate to guide a unified development of the resources of the region for the long-range benefit of the people. As one phase of this function, it is directed to co-operate with farmers in the experimental large-scale use of improved fertilizers and development of better fertilizer practices. Following careful study, it was concluded that the objectives of this phase could best be attained by soil rebuilding through the use of phosphatic fertilizer and lime in an improved farm management sys- tem. This activity was launched through a program of test and demonstration on farms and simultaneous technical investigations to develop new and improved phosphatic fertilizers. Phosphorus has since become a keystone of the Authority's resource development and conservation program. Human effort is being conserved by phosphate utilization on the farm, and mineral conservation has been promoted by technical developments in phosphate mining and manufacturing operations.

Jan 1, 1944

By H. J. Seaman

The cost of keeping platinum ware in repair becomes such an important item in laboratories where much fusion-work is done, that a method of saving in this direction may not prove unacceptable to at least some of the members of the Institute. Some two years since I had the misfortune to puncture an almost new Bishop crucible. As an experiment I endeavored to patch it, and with such success that it is still in constant use. This may be accomplished in the following manner : The crucible and patch, which should be of stout foil, are rubbed bright with silica, or rotten-stone; a light platinum wire, welded to a corner of the patch, and the whole treated for several hours with hot concentrated hydrochloric acid; after which they are thoroughly washed with distilled water and dried. The head of an ordinary iron rivet, 4 inches by $ inches, is rounded off by hammering to somewhat the shape of the crucible. This is sunk 2 inches in a block of hard wood, and firmly wedged in place. This serves for an anvil. The hammer is an ordinary cast-iron toy, 11/2 inches long, and # inches in face, mounted on a 4 inch iron rod, 10 inches long. A gas-blowpipe is fixed in a horizontal position, and the strongest heat obtainable with it directed upon the rivet head; this soon at-

Jan 1, 1885

By Bernard H. Coyle, Robert N. Anderson, Judith A. Koperski

Between 6 and 8 million cars are shredded annually in the U.S. This shredded material is magnetically separated leaving a mixture of nonmetallics and nonferrous metals which can be further separated into its metallic and nonmetallic constituents. The metallic portion is a mixture of metalr; and alloys containing predominately zinc, and some aluminum, copper, and residual iron. Hydrometallurgical strategies are proposed for recovering the aluminum, copper, and zinc. The thermodynamic and kinetic behavior of the most promising alternatives to separation are discussed.

Jan 1, 1978

By N. E. Garner

Laboratory experiments were conducted to investigate the cutting of a single diamond on limestone and shale under simulated down-hole conditions. A high-pressure chamber was modified by adding a rock-rotating device so that planing tests could be run. Weight on the diamond, diamond geometry and differential pressure across the face of the rock were varied. It was found that (I) high differential pressure reduced the volume of rock cut by the diamond at a given bit weight by strengthening the rock and changing the mode of failure; (2) a finely powdered rock left in the bottom of the grooves reduced the volume cut by as much as 50 percent; and (3) orientation of a single diamond about the axis of a drill point had considerable influence on diamond cutting efficiency. INTRODUCTION Diamond bits consist of many diamonds held in a matrix provided with water courses for fluid passage to clean, cool and lubricate the diamonds as they drill formation. Each diamond contributes its share to the overall effectiveness of a bit, but a lack of understanding of the performance of a single diamond has hampered efforts to engineer improvements in diamond bits. The need for those improvements prompted this study. This paper describes the findings of a laboratory investigation of the outting action of a single diamond where the differential pressure between the wdlbore and formation, diamond geometry and vertical force on the diamond were independently varied. The tests were conducted in a pressure chamber that provided relative horizontal motion (planing) between a rock and diamond under simulated down-hole pressure conditions. EQUIPMENT HIGH-PRESSURE CHAMBER WITH ROTATING DEVICE The high-pressure chamber used in previous rock mechanics studies' was modified for this study by addition of a rock-rotating device. The modified chamber (Fig. 1) differs from the old chamber in that the rock can be rotated to provide relative horizontal movement between the rock and the penetrator which may be a small element of a diamond or a drag bit. In this study the penetrator was a single diamond. The rock sample holder inside the chamber is mounted on a thrust bearing and is connected to the external drive mechanism by a stem that passes through two seal elements. The seal elements are needed to allow formation pressure to enter the bottom of the rock sample through a small hole in the stem. The Kapseal seal elements (Tefion boots backed by O-rings) provide low friction (hand free) even at differentials of 5,000 psi. The drive mechanism is a variable-speed transmission with a speed range from 0 to 30 rpm and an output torque of 2,800 in.-lb. A right-angle-drive gear box couples the drive to the stem. The new design has two independent pressure systems (formation and borehole) to simulate down-hole rock stress environment. Formation pressure enters from the bottom of the rock through a 6-in. diameter area, and borehole pressure acts over the remaining surface. A 14-in. layer of zero fluid loss oil-base mud poured over the top of the rock and an O-ring seal on bottom allow a differential between the borehole and formation pressures. Bayol 50 was used as the hydraulic fluid in the chamber. The differentials reported here were obtained by elevating the borehole pressure while keeping the formation pressure at zero.

By Edwin M. Chance

During the last decade many conditions have been encountered that have materially increased the cost of the production of coal. As in most cases it has not been practicable to increase the selling price of such coal sufficiently to insure the necessary margin of profit, the mine management has been forced to avail itself of what might be termed unusual means that costs might be held at as low a figure as possible. The so-called efficiency engineer has been called upon, costly power plants have been built and machinery has been installed to replace manual labor wherever possible. Another aid used recently to secure economies through the more intelligent production of coal, is the chemist. As the coal industry, barring the production of byproduct coke, does not at once give evidence of its need of the services of the chemist, the writer will endeavor to point out a few of the services that this branch of the staff has been able to render. The preparation of coal in the past has been carried on entirely upon an empirical basis, that is, the criterion adopted has been an ocular inspection. Unfortunately, the appearance of a coal and especially of an anthracite, has but little relation to its fuel value, and as long as coal is purchased for the heat that can be obtained from it by its combustion, the quantity of such heat that is purchased must be one of the principal desiderata in selecting or preparing a coal. Were coals purchased for use as bric-a-brac or for exhibition in museums it might be both wise and just to purchase them upon their appearance. After 4 or 5 years of investigation the fact has been established that coals of very inferior appearance, and I now have special reference to anthracite, might and often did possess heating and burning properties superior to those possessed by bright coals which in the past had commanded considerable and uniform premiums in the market. This being the case the question arose as to whether the trade could be convinced of this fact. While at first some difficulty was experienced in establishing the quality of such dull coals, still it was found that the real obstacle to the sale of these materials in the past had been the fact that the coal producers' own sales departments felt convinced of the inferiority of this type of fuel and when complaints were registered they were given ready credence. Upon convincing the sales department of the quality of this type of fuel, but

Jan 1, 1917

By Jim V. Rouse

There have been many changes in environmental control techniques since the early days of uranium mining and milling, when liquid mill effluents and often mill tailings were discharged directly into nearby streams. With today's stringent environmental controls, the uranium miner must be as aware of regulatory requirements as he is of techniques in mining, milling, and in-situ recovery. The time delays involved in bringing a uranium project on line dictate that the proposed facility be designed with a view not only of present regulations, but also of those which may be in effect when the facility is completed. While such predictions are difficult, it's almost certain that regulatory agencies will exercise even more environmental control over future uranium mining and milling operations, using the past errors of the 1950's as justification for increasingly stringent controls.

Jan 10, 1978

By W. B. Mather

Of the 61 dikes examined some yielded cassiterite, tantalite, and beryl; eight contained spodumene; and six carried amblygonite. Two mines stockpiled spodumene as a byproduct. Only zoned pegmatite dikes carried lithium minerals. GEOLOGICAL studies have revealed the occurrence of hundreds of pegmatite dikes in northeast Brazil, Fig. I, in the three states of Rio Grande do Norte, Paraiba, and Ceara. Heretofore data have not been available on the possible production of lithium minerals from these areas, and in March, April, and May 1953 the author undertook a reconnaissance survey covering a cross-section of the pegmatite~. Sixty-one pegmatites were examined. The pegmatites of Rio Grande do Norte and Paraiba are located in an arid region (Seratao), and except in the most southerly portion there is a minimum of vegetation and overburden. The region is easily prospected and relatively accessible by jeep or truck. The pegmatites examined in Ceara are in an area of lush vegetation along the flanks of the Jaqueribe River valley. It is therefore more difficult to prospect, and the dirt roads, as a means of access, leave much to be desired. For all practical purposes rail transportation, except in Ceara, is not available. The rocks of the area are composed of Pre-Cambrian schist, gneiss, quartzite, and marbles. They have been intruded by granites, monzonites, and diorites and cut by quartz veins and pegmatites. Pre-Cretaceous erosion reduced the area to a peneplain upon which Cretaceous or younger sandstones were deposited. Recent erosion has left only a few remnants of these younger rocks. In most of the Rio Grande do Norte-Paraiba area the pegmatites were more resistant to erosion than the enclosing schists and therefore stand out in relief. This is not true in the rolling country of Ceara, where the pegmatites lack topographic expression. With regard to structure and lithology, the pegmatite~ of northeast Brazil are divided into two types, uniform and zoned. Of the 61 examined, 19 belong to the uniform and 42 to the zoned type. Uniform pegmatites are normally long, narrow, and tabular, with sharp contacts. They are composed of an intimate mixture of feldspar (microcline or ortho-clase), mica (biotite, phlogopite, or muscovite), and quartz. The grain size5 varies from fine at the contact to coarser in the interior. They are not considered a commercial source of pegmatite minerals, although efforts have been made to produce green beryl of gem variety. This type of dike is often abundant in schists and gneisses close to granite intrusives. The productive dikes — lenticular, pod-shaped, or irregular in outline, with sharp contacts — are of the zoned variety. Zone contacts are gradational, except for those with the quartz core. Zones re identified as follows, see also Fig. 3. Border Zone: This outer zone, in contact with the country rock, is composed chiefly of fine-grained muscovite and biotite, with lesser quantities of finegrained microline and quartz. It is the narrowest zone, usually measurable in inches. Wall Zone: Lying between the border and intermediate zones, the wall zone is composed of medium-grained feldspar (often microcline), muscovite, and quartz. Usually it is the widest zone. Widths of 50 ft were noted. Intermediate Zone: Lying between the wall zone and core, the intermediate zone is composed principally of coarse-grained microcline (occasionally with some orthoclase and albite). It may also carry minor amounts of coarse-grained quartz and fine to medium-grained mica. The width varies from less than 3 ft to more than 30 ft. Core: The center of the dike is composed almost entirely of massive quartz, occasionally with minor amounts of fine-grained muscovite. The width reaches 30 ft. Lithium and other minerals of potential economic value are found in the following zones:

Jan 1, 1955

By A. R. Rule, D. C. Dahlin, D. E. Kirby

The US Bureau of Mines is currently engaged in research to characterize complex, low-grade western phosphate rock and to develop methods for economic recovery of phosphate, as part of a government effort to assure an adequate supply of fertilizer minerals. Western phosphate varies from soft, friable, altered phosphatic shale to hard, tightly cemented, unaltered phosphate rock. To supplement current methods of beneficiation (normally restricted to sizing), the USBM has developed a flotation procedure that includes depression of phosphate minerals with H2SiF6 and anionic flotation of carbonate minerals, followed immediately by cationic flotation of silicate minerals. Tested on several different ore types, the procedure has yielded phosphate concentrates that range in grade from 28 to 31% P2O3 with a phosphate recovery factor of 60 to 70%.

Jan 1, 1978

By AIME AIME

WTHIN the next month all members of the Institute will be given an opportunity to vote for a new President, two Vice-Presidents, and five Directors. All of the candidates nominated by the official committee are well known to certain groups of the Institute membership but a brief record of their professional lives will be given here for the information of those that will vote. Not since 1927, when Everette DeGolyer guided the destinies of the Institute, has a member of the Petroleum Division been a candidate for President. John Meston Lovejoy has been a Director since 1930, and a Vice-President as well for the last year: In the three years 1932-4 lie was also chairman of the Admissions Committee. Dir. Lovejoy graduated from the Columbia School of Mines in 1911, just before lie was 22 years old, and began his professional career as a copper miner at Chuquicamata. Chile. Silver and gold mining later claimed his % attention, and it was not until 1914 that lie gut into the oil business, as geologist for the Standard Oil Co. of N. Y. This took hint to China and he later worked for the company in Wyoming. In 1917 lie joined the Army where lie rose to be captain of Field Artillery. Upon his return to the United States he went to work for the Amerada Petroleum Co., of which he later became vice-president and general manager, with headquarters in Tulsa. Since coining to New York he has been president of the Petroleum Bond & Share Cu.. and is currently president of the Seaboard Oil Co.

Jan 1, 1935

By H. R. Stahl

THE disseminated lead district of Southeast Missouri lies 70 miles south of St. Louis. The only metal of economic importance in the ore is lead, but minor amounts occur of iron, zinc, copper, cobalt, nickel, silver and cadmium. These minor metals, as might be expected, tend to concentrate in both the flotation and table middlings. In the past, some zinc has been recovered by differential flotation. The silver and cadmium tend to associate with the zinc, and some recovery is made of these two metals at the smelter. The lead occurs as galena, or lead sulphide. The minor metals are also present as sulphides. The presence of oxidized lead is suspected, but has not been definitely proved. The gangue is chiefly dolomitic limestone, with small amounts of sandstone and shaly glauconitic and chloritic minerals. The ore contains about 3.25 per cent lead, occurring as galena disseminated through the gangue. Some of the galena is very finely disseminated, and the mineral in the gravity tailings, or chat, is seldom or never in the free state. The method of treatment of the ore has been evolved over a period of 75 years; hence probably is not far from correct. The milling processes have tended toward simplification during the past 15 years, but recoveries have never been sacrificed for the sake of simplicity. In many cases, simplification of flowsheets has led to better recoveries and operating economies. A simplified flowsheet is shown in Fig. I. The St. Joseph Lead Co. operates four mills in the Flat River district, with a normal total capacity of about 21,000 tons per day, divided as follows: Federal mill, 11,000 tons; Leadwood mill, 4500 tons; Desloge mill, 3400 tons and Bonne Terre mill 2400 tons. The methods of concentration used at these plants are similar in principle; they differ mainly in details and in the type and size of the equipment used. The process of concentration may be divided into five main steps; i.e., dry crushing, wet grinding, classification with its attendant desliming, tabling and flotation. A brief description of these processes will be given, noting important differences in the various plants, and also noting the more important changes or developments of the past few years. DRY CRUSHING The run-of-mine ore is hoisted in skips, the capacity of these skips ranging from 2 ¾ tons to 8 ¼ tons. At the Desloge plant, the ore is hoisted in 2-ton mine cars on self-dumping cages. All ore is hoisted at shafts adjacent to the various crushing plants, no ore being transported on the surface. Primary breaking at all the mills is accomplished with 9E Telsmith breakers. Preliminary screening is provided ahead of most of these crushers, either by station-

Jan 1, 1943

REJUVENATED is an apt word to apply to Chino, Kennecott's big open-pit mine at Santa Rita, New Mexico. Back in 1923 Chino was merged with Ray by an exchange of shares, and in 1926 the Ray-Chino combination was taken over by Nevada Consolidated through an issue of bonds that were traded for the Ray and Chino assets. Subsequently, of course, the whole package was acquired by the Kennecott Copper Corporation. On the basis of the terms of the Ray-Chino-Nevada exchanges, Chino was rated third in value, something less than thirty per cent of the total. In 1955 the appraisal would doubtless be forty per cent or more. But it is not only vis-a-vis Ray and Nevada that Chino has blossomed out. At the end of 1931, Chino ranked seventh among the Porphyries in point of output; whereas by the end of 1954 it was fifth,. having passed both Inspiration and Nevada Consolidated. Sharp curtailment in production in 1932-33-34 and total suspension in the two years following (see Fig. 21) found the property in a somewhat parlous position. However, the engineers had not been idle; they had been planning for the future, and in 1937 a far-reaching program of rejuvenation was launched. During the ensuing five years, capital expenditures totaled more than $8,500,000. Among the projects undertaken were the following: (1) Mine-Purchase of larger and better equipment for drilling, loading, and transporting the ore. (2) Mine-Beginning of the first systematic project to leach and recover copper in the waste dumps at the mine.

Jan 1, 1957

By Don Rose

In the USA the cost of steel ribs for tunnels approximates $100 million each year. European practice has long since abandoned heavy steel ribs for tunnel support, and tunnel coats in Europe (normalized for wages) are about half the costs incurred in the USA. A feeling has existed for some time that the USA practices of supporting tunnels with heavy steel ribs have been overly conservative. The USA practice is based on rock load coefficients by Karl Terzaghi. In 1946, Karl Terzaghi published a tunnel rock classification system (Terzaghi, 1946), with the rock loads on tunnels predicted for each class of rock. No data on real rock loads were presented by Terzaghi and his rock load coefficients may have been largely intuitive. His classification system and associated predicted rock loads have been widely used in the USA. Each rock class, taken from Terzaghi's classification system, is assumed to generate loads of loosened rock resting as dead load. The dimensions of the loosened rock are described by rock load coefficients multiplied by the tunnel diameter. The resulting rock loads are used by design engineers, contractors and agencies to size supporting steel ribs. Terzaghi clearly stated that he had conservatively assumed high rock loads for his classes 4, 5 and 6 to take a presumed effect of groundwater into account. If the tunnel was not affected by ground- water, Terzaghi stated those rock loads should be reduced by 50 percent. Twenty two years later Tor Brekke (1968) wrote a paper clearly showing that based on observation of more than 250 tunnels groundwater does not affect tunnel rock loads. In 1969, Deere, et al., published measurements made on a number of tunnels, and a well-known curve was drawn by Deere to illustrate Terzaghios coefficients graphically. Deere's text stated that Terzaghi's predicted rock loads were too high and should be reduced. Cording and Deere (1972) more recently published data indicating that very large real rock caverns and chambers were being successfully built using rock bolts, which can take only a very limited rock load, thus indicating that real rock load is much smaller than Terzaghi or even Deere predicted.

Jan 1, 1982