Search Documents

By L. D. Jaffe Hollomon, Hollomon John H.

For many steel parts it is desired to obtain the maximum toughness consistent with the strength required by the mechanical design. It is generally recognized that the greatest toughness at any given strength is found in steels having a tempered martensitic structure.' and is virtually independent of the composition of the steel2 (except for carbon). The choice of the composition of a steel for the parts in question should be based, therefore, on hardenability considerations and on manufacturing facility and economy. In a recent paper3 the concept of hardenability was discussed and a somewhat new approach to the problem was suggested. The hardenability was defined in terms of the cooling conditions (speed of cooling) required to avoid the pearlite and the bainite reactions. Since all the alloying elements do not have the same effects on the two reactions, the bainitic and pearl-itic hardenabilities must be considered separately. In order to design a steel for a given part, it is necessary to design a composition that has both sufficient pearlitic and sufficient bainitic hardenability. However, this requirement does not fix the combination of alloying elements to be used; an infinite number of steels would have the required hardenabilities. Other considerations limit the choice. For example, decreasing the carbon content increases the toughness at a given hardness, and for this reason low-carbon steels are often desired. Limitations or requirements of refining, casting, or forming practices often affect the level of some of the alloying elements. Price considerations enter. Frequently, however, it is very desirable to minimize the tendency toward quench-cracking while maintaining the necessary hardenability. This paper is concerned with suggesting a method for choosing compositions that will have the required hardenability together with minimum tendency toward quench-cracking. Quench Cracking Since only the case in which the entire part will transform to martensite in the particular quench employed is being considered, the analysis of the quench-cracking problem is somewhat simplified. Quench-cracking arises from the temperature gradients existing throughout the piece during cooling. Because of these temperature gradients, the contraction arising from the decreasing temperature and the expansion arising from the austenite-martensite reaction do not occur uniformly over the parts, and stresses are set up that tend to cause cracking. The temperature gradients can be reduced by decreasing the severity of quench. This, however, requires that the hardenability be correspondingly increased by increasing the carbon or alloy content. An

Jan 1, 1947

By Hollomon John H., L. D. Jaffe Hollomon

For many steel parts it is desired to obtain the maximum toughness consistent with the strength required by the mechanical design. It is generally recognized that the greatest toughness at any given strength is found in steels having a tempered martensitic structure.' and is virtually independent of the composition of the steel2 (except for carbon). The choice of the composition of a steel for the parts in question should be based, therefore, on hardenability considerations and on manufacturing facility and economy. In a recent paper3 the concept of hardenability was discussed and a somewhat new approach to the problem was suggested. The hardenability was defined in terms of the cooling conditions (speed of cooling) required to avoid the pearlite and the bainite reactions. Since all the alloying elements do not have the same effects on the two reactions, the bainitic and pearl-itic hardenabilities must be considered separately. In order to design a steel for a given part, it is necessary to design a composition that has both sufficient pearlitic and sufficient bainitic hardenability. However, this requirement does not fix the combination of alloying elements to be used; an infinite number of steels would have the required hardenabilities. Other considerations limit the choice. For example, decreasing the carbon content increases the toughness at a given hardness, and for this reason low-carbon steels are often desired. Limitations or requirements of refining, casting, or forming practices often affect the level of some of the alloying elements. Price considerations enter. Frequently, however, it is very desirable to minimize the tendency toward quench-cracking while maintaining the necessary hardenability. This paper is concerned with suggesting a method for choosing compositions that will have the required hardenability together with minimum tendency toward quench-cracking. Quench Cracking Since only the case in which the entire part will transform to martensite in the particular quench employed is being considered, the analysis of the quench-cracking problem is somewhat simplified. Quench-cracking arises from the temperature gradients existing throughout the piece during cooling. Because of these temperature gradients, the contraction arising from the decreasing temperature and the expansion arising from the austenite-martensite reaction do not occur uniformly over the parts, and stresses are set up that tend to cause cracking. The temperature gradients can be reduced by decreasing the severity of quench. This, however, requires that the hardenability be correspondingly increased by increasing the carbon or alloy content. An

Jan 1, 1947

By Dennis E. Stover

Grade control for in situ uranium leaching is maintaining, at desired levels, the uranium concentration in the pregnant lixiviant which feeds the extraction (ion exchange) circuit. This differs from grade control in conventional mining in that in situ grade control is imposed subsequent to rather than prior to leaching without the direct observation and control possible in conventional mining and milling. Grade control is a necessary engineering task through the entire project life, beginning with preliminary evaluation and design and ending only when the final wells are shut in. More specifically, this task is associated with designing the initial well field, maintaining productivity during well field operations, and planning well field expansions to compensate for the depletion of existing wells. Our aim during each of these phases is to maximize uranium productivity while ensuring that we are developing information necessary for future phases. Throughout this task, we remain cognizant of the fact that uranium productivity is a function of both the complex geologic and operational parameters of the project. A minimum list of significant geological factors must include the following: . Host formation mineralogy . Uranium mineralogy . Permeability . Ore quality (grade and thickness) Our concerns are not limited to average or general descriptions of these factors. The interactions among the factors as well as localized variations among them are far more important in obtaining high productivity from a deposit. For example, an ore body may display an average permeability of one darcy but have its high grade ore confined to regions with permeabilities less than 500 millidarcies. This relationship between ore grade and permeability must be understood early in the project life if the operation is to be successful. Similarly, the fundamental operating parameters for the well field include those items which enable us to distribute the lixiviant within the ore as well as the chemistry which will dissolve the uranium minerals. A minimum list of such factors will include: . Well design . Well efficiency . Well bore damage . Pattern size and shape . Oxidant type and concentration . Complexing agent concentration - pH The interactions between these variables and the complex geological variations create a situation which often defies quantitative analysis. Hence, we have adopted a statistical approach when correlating production history with these parameters and the quality of the correlations improves as the number of wells operated increases. However, the correlations are often specific to an ore body. We find that we must tailor the process to meet the unique geologic parameters of each ore body. PHASE 1: INITIAL WELL FIELD DESIGN Designing the initial well field is perhaps the most difficult phase because we have the smallest data base from which to predict performance. We will have conducted numerous laboratory tests and, perhaps, field pilot tests to select the lixiviant system and to characterize the geologic parameters. However, we will learn a great deal more about the deposit and its productivity during actual commercial scale operation. Fully acknowledging its limitations, we will, as a starting point, assume that uranium productivity will be directly proportional to the quality and quantity of recoverable reserves. Future deviations from this assumption will be plentiful and result from our limited understanding of the aforementioned interactions between and among the operational and geological factors. However, in planning the initial field, estimation of the quantity of leachable uranium present at levels above the economic grade and grade-thickness limitations is a priority task. (The concentration of uranium in the ore, the ore grade, is expressed in units of weight percent. The grade-thickness of the ore is the product of the average grade and ore thickness expressed in units of percent-feet.) These parameters provide a direct indication of the quality and quantity of ore. They are determined from gamma logging of closely spaced drill holes (50 to 100 foot centers being typical) accompanied by uranium core analysis or direct uranium assay logging. Gamma- logging measures gross gamma radiation which emanates from uranium decay products and indicates only the possible presence of uranium. Direct uranium assays are necessary to confirm this presence and the true location and quality of the reserve. From this information, an estimate of the in-place uranium reserve is formulated. Utilizing the above data, we begin to assess the quantity and quality of the leachable reserve. Analysis of self-potential and resistivity logs in conjunction with uranium logs will identify those zones which contain uranium and display apparent high permeabilities. Similarly, zones with extensive calcite cementation or dense clay sedimentation are located and uranium within such zones is excluded. (Interpretation of these logs should be confirmed

Jan 1, 1980

By Duane E. Eubanks, David B. McDonald

The anticipated growth of western coal production over the next decade is expected to add approximately 274.3 million t/y (302.4 million stpy) to US capacity. The increased output, coming from both new mines and expansion of existing facilities, promises to bring with it a new set of problems for mine planners.

Jan 8, 1976

By R. W. Bond

The gas-lift is a comparatively recent development in the Oklahoma and Kansas fields. It was used to some extent in the old Dilworth field several years ago, but the first extensive installations were made in the Tonkawa and Garber fields in Oklahoma early in the year 1926. Compressor Equipment During the early development of the system, the equipment used generally consisted of small tandem compressors of about 250 cu. ft. per min. displacement, driven by automotive-type gas engines, using a short belt drive. These compressors were first installed at the individual wells largely as an experiment. After the experimental installations had proved the method a success, it was considered economically advisable to centralize the compressor equipment in strategically located stations. However, as the information in regard to "gas-lift flowing life" was anything but definite, and the most optimistic estimates in regard to it did not exceed six months, portability of equipment was still the first consideration in the minds of many operators, who continued to install srnall semi-portable com-pressors in their centralized stations. As electric power became available in the fields, the electric motor came rapidly into use as the prime mover for the small compressors. The operating cost of this motor is greater than that of the automotive-type gas engine for the same power output, but the greater continuity of service tends to balance the extra cost. Aside from the semi-portable units, a number of strictly portable compressors were used. These consisted of automotive-type gas engines direct connected to vertical compressors. The unit was assembled on one base and could be mounted on wheels or skids as desired. The chief objection to these, in the writer's opinion, was their small capacity— approximately 150 cu, ft. per min.—which made it necessary to use two, three, and sometimes more units per well, thus making the installation rather costly. However, they have been found valuable for test purposes and emergencies, where installation time is an important factor.

Jan 1, 1928

By Waldemar Lindgren

DURING the last 15 years much attention has been given to the "contact-metamorphic" ore deposits which mainly occur in limestone close to intrusive contacts. In general, these deposits are characterized by the association of magnetite and simple sulphides with the so-called "contact-metamorphic" silicates. These silicates comprise garnet, epidote, vesuvianite, tremolite, wollastonite, diopside, hedenbergite, ilvaite, and many other rarer forms. The ?contact-metamorphic zones contain also in places minerals with boron, fluorine, and chlorine, like axinite, tourmaline, danburite, fluorite, and scapolite. There is also more or less quartz and coarsely recrystallized calcite. The simple sulphides embrace pyrite, pyrrhotite, chalcopyrite, galena, zincblende, more rarely arsenopyrite. On the whole, sulphantimonides and sulpharsenides are rare. Deposits, of magnetite or chalcopyrite or of both are most common. The deposits have an irregular or rudely tabular form, following main contacts, dike contacts, or stratification planes; they rarely extend for more than 1,500 or 2,000 ft. from the contact; far more commonly they only reach a distance of a few hundred feet from that surface. The deposits are usually formed by replacement of limestone, or allied calcareous rock. Apparently they are found both in relatively pure and in impure carbonate rock. The deposits are geological bodies of a chemical and mineralogical character differing greatly from the adjoining intrusive rock and from the unaltered limestone. They are rich in silica and iron, with more or less of lime, magnesia, alumina, sulphur, and rarer metals like copper. The so-called contact-metamorphic silicates which form the gangue usually are coextensive with the metallic minerals, though of course not necessarily with the merchantable ore. All opinions agree in holding the deposits of epigenetic origin, later than the inclosing limestone. Regarding the origin of the metals and the genesis of the ores there are several opinions.

Jan 6, 1914

By G. G. Sarkar

SHARPNESS of separation and washing efficiency are often confused. The sharpness index indicates the precision of a washing unit; the washing efficiency takes into account not only the unit's precision but also the washability characteristics of raw coal and the near-gravity materials at the effective density of cut. A sound basis for evaluating the sharpness index is essential in comparing the sharpness of separation attained by different cleaning units. Sharpness Index and Related Criteria: Washing plant sharpness of separation has been well represented by Hancock's efficiency chart and Tromp's curve of migrated materials. Some useful coefficients derived from Tromp's curve—the error area, probable error, and imperfection value—have been widely used to measure sharpness of separation. These are defined in a number of papers presented at the first and second International Coal Preparation Colsference held in Paris (1950) and Essen (1954).1-5 In evaluating the performance of a dense medium separator at four different gravities, Yan-cey and Greer6 bserved that even with similar operating conditions and the same size grading of feed, the imperfection value of a washing plant varies through a greater range than the probable error. The present writer also observed the same type of anomalies in comparing the imperfection values of one plant which were determined under almost identical conditions. He therefore devised a graphical method to evaluate a washing unit's sharpness of separation and define it by a single coefficient, which is substantially independent of coal characteristics under normal operation of the unit. Unlike imperfection value, the new coefficient can be expressed on a percentage basis. Coal preparation engineers generally agree that the amount of misplaced material resulting from any separation in a washing plant is almost directly related to the amount of +0.10 sp gr (near-gravity) materials. In actual practice, however, misplacement is not restricted to the 20.10 sp gr range. It will be evident from a study of Tromp curves that this misplacement often extends over unequal specific gravity ranges on the two sides of the actual density of separation. The same condition exists for near-gravity ash distribution and the resultant misplacement of ash units during any separation. But so far as the same unit is concerned, the total misplacements bear a definite ratio to the amount of near-gravity zone materials that is affected by misplacements. This ratio should be constant not only for various densities of separation but also for different qualities of feed coal treated in the same plant. This ratio, multiplied by 100, directly represents the inefficiency of the plant. When the plant inefficiency value is subtracted from 100, the re- ' sult is designated as sharpness index. Evaluating the Sharpness Index: The method of evaluating the sharpness index is explained here with reference to Fig. 1. Fig. 1 is a reproduction of the familiar diagram used by Cerchar of France to represent the inefficiency of a separation in terms of "triangle of errors," which is a measure of organic loss. It will be observed that the characteristic (yield/fractional ash) curve of the raw coal represented by GHAPR

Jan 1, 1958

By Robert C. Mackenzie

EXAMINATION by the differential thermal analysis technique of a large number of samples of soil and other clays from various parts of the world has demonstrated that the occurrence of cold-precipitated hydrated ferric oxide (the identification of which in soil clays has previously been reported5) is not confined to any limited locality; e.g., it has been found in varying amounts in clays from Britain, France, South Africa, and Mexico. The conditions necessary for its formation have not yet been elucidated in spite of the number of samples examined, and, since this mineral is so easily prepared in the laboratory, it has been considered that a study of its constitu¬tion and of the conditions under which it could be prepared might. lead to a better understanding of the factors involved. These experiments form the subject of this short paper, and while they do not supply a definite answer to the mode of formation of this mineral in nature, they may, it is hoped, add something to our knowledge in this direction. EXPERIMENTAL WORK Materials Employed The a-Fe2O3.H2O (goethite) and B-Fe2O3.H2O (Weiser and Milligan") were obtained from the Department of Geology, University of Aberdeen, and Rothamsted Experimental Station, respectively. The beta material had been prepared by the method described by Fernelius.1 y-Fe2O3.H2O (lepidocrocite) was prepared at the Macaulay Institute for Soil Research by the method of van Schuylenborgh.6 The method employed for preparation of the cold-precipitated hydrated ferric oxide* was as follows: 1: 1 NH4OH was added (moderately fast with rapid stirring) to a solution of 5 grams FeC13.6H2O in 250 ml distilled water at room temperature (ca. 15°C) until red litmus turned blue, and then 2 to 3 drops in excess. The resultant precipitate was filtered off on a Buchner funnel and washed free from Cl- with distilled water. Previous experiments having shown that drying over P2O5 at room temperature or drying at 105°C in the oven did not significantly affect the thermogram,5 samples were nor-

Jan 1, 1952

By N. E. Grosvenor

The study of rock mechanics is becoming more important each year and several groups are currently engaged in the study of rock mechanics instrumentation and techniques that can be used to determine rock properties in place. As it becomes necessary to mine lower grade ores, larger equipment and tonnages are required, which in turn call for larger openings underground. In addition, rock mechanics studies are necessary for designing large underground openings for defense and powerhouses, and highway and water tunnels. Meramec Mining Co. has a rock mechanics program in which they are trying to develop a means of detecting ground instability prior to failure. In one case advance warning resulted in valuable lead time for back filling stopes before pillar failure had progressed to a dangerous extent.1

Jan 2, 1968

By T. F. Witherbee

IN the sections, Figures 1, 2, and 3, are shown three crucibles that have been applied to substantially the same furnace, all the conditions having been the same except a variation of one foot of bosh, and a slight variation in the angle of the same. The bosh of No. 3 was originally the same as No. 2, the additional foot in diameter being the result of three months' cutting. Beginning with No. 1, which was 5 feet 6 inches diameter, with tuyeres 5 feet 4 inches high, and cinder-tap four feet from bottom, great trouble was found in holding iron a proper length of time, four hours being the outside limit when working well, and two hours or less if working badly. "Break-outs" through the iron

Jan 1, 1880

By Robert H. Dickson

Limestone replacement and contact metamorphic orebodies are 80 irregular that sampling and estimating are far less. exact than in more regular types of deposits; both the mineralized masses and the lenses of ore within them are extremely irregular. So much development work is required to find the ore that the expense of blocking out great tonnages is prohibitive; furthermore, the rock near these orebodies is so heavy that drifts or raises cannot be kept open for many years without excessive repairs. As a result, few mines in limestone have more than three years supply of ore in sight. As most of the ore, is developed by stoping— not by drifting, raising, or drilling—estimates of ore developed do not indicate the total amount of ore that may be expected; they simply indicate the relative condition of the mines. But even if they are to do this, they must be made according to a fixed plan, intelligently carried out. The estimates of ore in the Calumet & Arizona Copper mines, Warren District, Ariz., have been of much value to those who plan the mining and development work. This paper describes the methods of sampling and estimating used in these mines. Sampling Samples are taken in various ways and depend on the condition of the working and the purpose for which the sample is to be used. Drifts, crosscuts, and raises are sampled by channels or by taking a grab off each mine car as it is filled. Stopes are usually sampled by drill holes or by taking a representative sample off each mine car; the latter, or chute, sample is by far the best sample. All workings are studied periodically by an engineer, who makes graphic and detail notes of the geologic structure, as shown in Fig. 1. The daily car tally and assay of each particular working is added to the same sheet opposite the material it represents. These sheets make a permanent record, showing the exact boundaries as well as the grade of ore in all workings.

Jan 1, 1925

By W. T. Jr. Thom

INTEREST naturally attaches to fissuring and subsidence of the earth's surface, whatever the cause may be, and the induced movement and fissuring of the impervious strata overlying an oil sand is of even greater practical importance because of its bearing upon the recoverability of the portion of the oil not already extracted or extractable by ordinary production methods. It is probably true that significant ground movement induced by oil production occurs only in oil fields in relatively young formations, where the oil comes from incoherent or only slightly cemented sands and oil-soaked clays, but inasmuch as a great proportion of our "gusher" wells produce from "running" sands and yield a large part of the total oil output, it seems worth while to make an effort to inspire the collection and recording of data indicating the nature and magnitude of oil-field subsidence, both surface and subsurface.

Jan 1, 1927

By Howard N. Eavenson

AN analysis of the bituminous coal situation by an authority who traces the production, mining, safety, markets and labor trends in comparison with other fuels. BEFORE 1918 the production of coal experienced a steady growth, with slight recessions in ouput in only twelve years (1837, 1841, 1852, 1855, 1861, 1874, 1876, 1889, 1894, 1905, 1909, 1914), and in each of these cases the loss was recovered in the following year and the increase continued. In each decade the output was doubled. Prices, while not high, allowed some profit. In 1918 during World War I, an output of 580 million tons was reached and with the exception of 1923 this total was not again reached until 1942, in World War 11. Losses of output in this period were much greater than ever before; in 1932 the total was 270 million tons less than in 1918 or 1923, and the loss after 1923 was not recovered until 1942. The greatest output was 631 million tons in 1947.

Jan 1, 1950

ALL the ores of any kind whatsoever, even though they be semiminerals and may be perfect in their qualities, have to be recognized by experienced and good sorters. These men must have a detailed as well as a general experience of the metals so that in this first preparation, which is most important, they may know how to distinguish the good from the bad, and to know what is rock and what is ore. They must use patience in this, breaking and cutting and king the ore from the earth. They must separate the good ore from the bad, avoiding as far as possible every occasion for poisoning it by traces of other ores, evil stones, or other things inimical to its nature. Finally, with the judgment of the eye and with tools, and, in the end, by roasting it with fire and then quenching it with water, or by washing and re-washing it, the ore must be made as pure as possible in order to join it better with the companions that seem to be the most beneficial for its needs. Ores would be useless stones without smelting. Therefore, when it is certain that such ores are of divers elemental mixtures, aid must be given to each one according to the evil ingredients [47v] that harm it. But because such evil qualities are things that are often not apparent to the eye, such as too great a burning, or too much earthiness so that when they are alone the fire burns these ores before it melts them, it is necessary to temper them with other materials. To do this it is necessary to have the ability

Jan 1, 1942

By I. N. Knap

Discussion of the paper of HOWARD R. HUGHES, presented at the Now York meeting, February, 1915, and printed in Bulletin No. 99, March, 1915, pp. 629 to 635. I. N. KNAPP, Ardmore, Pa.-The claims made in the paper for the Sharp & Hughes cone bit are modest. I have used it with satisfactory results. It is a wonder for eating through hard, brittle rock; it will drill through iron pyrites that the fish-tail bit cannot enter. Soft ground is apt to contain concretions that are much harder than the containing ground. ?We have at times in drilling with a fish-tail bit thought the hole was partly in such hard material and partly in soft, thus making a difficult place to drill past in the ordinary way. By changing to a Sharp & Hughes cone bit such obstructions were easily overcome. This cone bit has greatly widened the range of work that may now be profitably accomplished by the hydraulic rotary method of drilling. It is not, however, adapted to drill soft or sticky ground, the old fish-tail bit being better for such purposes. The fish-tail bit usually scrapes its way through the material drilled, but not always. I believe at times it cuts and chips in soft friable rock. That is, the bit seems to bite into the rock, and when sufficient torsion is put on the drill stem it breaks its hold and jumps around and chips the rock from the bottom of the hole, like a stone cutter's chisel, and then takes another hold. This condition occurs only in friable material when the bit is sharp and the feed properly controlled. The Sharp & Hughes cone bit is a most valuable -tool for the rotary driller.

Jan 5, 1915

By Theodore Marvin

USE of airplanes to facilitate mining and petroleum operations has definitely left the "doubting Thomas" stage. As a matter of fact, front pages no longer record the novelty of this efficient arm of the mineral industry. We are now down to the facts basis. The recent aviation issue of Engineering and Mining Journal added - to our fund of knowledge on applications which the A.I.M.E. Aviation Committee is extensively adding to through its world-wide compilation of specific data. Another indication of the advance of flying in our. industries is the addition of regular aviation specialists to the staffs of various mining and petroleum companies, who function in the organization the same as do the metal

Jan 1, 1936

By R. W. Raymond

THE death of Louis Janin, which took place Mar. 6, 1914, at Santa Barbara, terminated the earthly career of almost the last survivor, and one of the most illustrious, members, of that group of American mining engineers and metallurgists who, in the last quarter, of the nineteenth century, directed the development of the mineral resources of the Pacific slope. Louis Janin was born in 1836 at New Orleans. His grandfather, an officer in the French army, had emigrated to this country, with his family, at or before the outbreak of the French revolution. His father became an

Jan 7, 1914

By Robert Yerkes

THE following is a brief account of the methods of measuring intelligence especially prepared for use in the U. S. Army, of typical results, and of some of their immediately practical applications. It has been prepared for the assistance of army examiners and for the information of all who are interested in the relations of scientific placement to military efficiency. PURPOSE OF THE INTELLIGENCE TESTS Under the direction of the Division of Psychology, Medical Department, and in accordance with provisions of War Department General Order No. 74, mental tests are given recruits during the 2-wk. detention period. These tests provide an immediate and reasonably dependable classification of the men according to general intelligence. Their specific purposes are to aid: 1. In the discovery of men whose superior intelligence suggests their consideration for advancement; 2. In the prompt selection and assignment to development battalions of men who are so inferior mentally that they are suited only for selected assignments; 3. In forming organizations of uniform mental strength where such uniformity is desired; 4. In forming organizations of superior mental strength where such superiority is demanded by the nature of the work to be performed; 5. In selecting suitable men for various army duties or for special training in colleges or technical schools; 6. In the early formation of training groups within regiment or battery in order that each man may receive instruction and drill according to his ability to profit thereby;

Jan 2, 1919

By James R. I. Henagan, William O. Crego

The Mamou Field, located in Evangeline Parish, La., is an elongated anticlinal structure on the downthrown side of a major east-west fault with oil and gas production from the upper part of the Wilcox formation. Two main producing horizons occur at an approximate depth of 11,500 ft and have been designated the Morein sand and the Deshotels sand. The upper sand (Morein) had an original bottom-hole pressure of 6,788 psig, which is some 1,500 psi above the normal pressure for that depth. Oil production with high gas/oil ratios and fluid analyses giving high shrinkage factors prompted a study of the reservoir in its early stages. The results indicated a closed reservoir producing under solution gas drive with low expected ultimate oil recovery. The early study of the Wilcox formation and its contained hydrocarbons resulted in the presentation of the data to the Department of Conservation of the State of Louisiana. with suggestions for field rules and a request for permission to inject extraneous water into the Morein sand. The water injection plans eventually led to complete unitization of working and royalty interests, to the construction of a gasoline plant, and to a central tank battery installation for the field. Deshotels sand wells were reworked to the Morein sand, and the water injection system was installed and ready for continuous operation in the early part of 1949. The injection of water was started in time to arrest the bottom-hole pressure decline at or near the bubble-point pressure. This injection was calculated to increase the ultimate recovery and to conserve natural resources. Pressure maintenance, the extraction of LPG products, and the sale of residue gas (early 1950) represent an attempt to produce an oil field with utmost efficiency. INTRODUCTION The two principal Wilcox oil horizons in the Mamou Field are the Morein sand and the Deshotels sand, occurring at 11,500 ft and 11,700 ft subsea, respectively. Minor oil production has been encountered in Morein stringer sands. (Fig. 1.) This paper deals only with the Morein sand, which is blanket over the Mamou Field. It is, however, segmented by the northwest-southeast "E" fault as shown in Fig. 2. The west segment is the area involved in the water injection pressure maintenance program. To date the east segment has operated largely under the influence of a strong water drive. The paper presents (1) a brief history of field development, (2) a resumé of reservoir conditions which led to the decision to inject extraneous salt water into the principal producing horizon, and (3) a summary of reservoir analysis and performance. FIELD DEVELOPMENT The Mamou Field is located in Evangeline Parish, La. The discovery well (J. B. Morein No. 1, now Unit No. 5) was completed in December, 1945, after penetrating 200 ft into the Wilcox formation. Initial production from the Morein

Jan 1, 1951

By James R. I. Henagan, William O. Crego

The Mamou Field, located in Evangeline Parish, La., is an elongated anticlinal structure on the downthrown side of a major east-west fault with oil and gas production from the upper part of the Wilcox formation. Two main producing horizons occur at an approximate depth of 11,500 ft and have been designated the Morein sand and the Deshotels sand. The upper sand (Morein) had an original bottom-hole pressure of 6,788 psig, which is some 1,500 psi above the normal pressure for that depth. Oil production with high gas/oil ratios and fluid analyses giving high shrinkage factors prompted a study of the reservoir in its early stages. The results indicated a closed reservoir producing under solution gas drive with low expected ultimate oil recovery. The early study of the Wilcox formation and its contained hydrocarbons resulted in the presentation of the data to the Department of Conservation of the State of Louisiana. with suggestions for field rules and a request for permission to inject extraneous water into the Morein sand. The water injection plans eventually led to complete unitization of working and royalty interests, to the construction of a gasoline plant, and to a central tank battery installation for the field. Deshotels sand wells were reworked to the Morein sand, and the water injection system was installed and ready for continuous operation in the early part of 1949. The injection of water was started in time to arrest the bottom-hole pressure decline at or near the bubble-point pressure. This injection was calculated to increase the ultimate recovery and to conserve natural resources. Pressure maintenance, the extraction of LPG products, and the sale of residue gas (early 1950) represent an attempt to produce an oil field with utmost efficiency. INTRODUCTION The two principal Wilcox oil horizons in the Mamou Field are the Morein sand and the Deshotels sand, occurring at 11,500 ft and 11,700 ft subsea, respectively. Minor oil production has been encountered in Morein stringer sands. (Fig. 1.) This paper deals only with the Morein sand, which is blanket over the Mamou Field. It is, however, segmented by the northwest-southeast "E" fault as shown in Fig. 2. The west segment is the area involved in the water injection pressure maintenance program. To date the east segment has operated largely under the influence of a strong water drive. The paper presents (1) a brief history of field development, (2) a resumé of reservoir conditions which led to the decision to inject extraneous salt water into the principal producing horizon, and (3) a summary of reservoir analysis and performance. FIELD DEVELOPMENT The Mamou Field is located in Evangeline Parish, La. The discovery well (J. B. Morein No. 1, now Unit No. 5) was completed in December, 1945, after penetrating 200 ft into the Wilcox formation. Initial production from the Morein

Jan 1, 1951