Search Documents

By John A. Church

When, in 1879,I examined the mines of the Tombstone Mill and Mining Company, at Tombstone, Arizona, I found a bed of tailings containing 12,000 tons, which had a value of 9 to 12 ounces of silver per ton and some gold. The ore had been amalgamated in pans, in which each charge had been ground for four hours, having been pre viously stamped through rough-punched screens, which gave a pro duct varying from 1-100th to 1-20th of an inch, according to the state of wear of the screen. It was certain that a large proportion of the tailings must be in fine slimes, and the question of recovering their value was difficult. Even now the concentration of slimes is . an unwelcome task, and at that day very little was known about it. Nevertheless, after considering the results of a test by repanning the tailings, I advised the company to concentrate and smelt, although they had to face the difficulty of making a smelting-product from slimes containing only 3 per cent. of lead. Limestone was abundant enough, but no iron suitable for flux was to be had for hundreds of miles. One of the company's claims con tained an argeutiferous manganese-ore, which gave but poor results by amalgamation. This was one reason for recommending smelt ing ; for if manganese would play the part of a precipitant, as iron does, the company could smelt by combining two of its silver ores, without other flux than the small amount of lime that might be needed. At that time no smelter had ventured to trust manga nese as a precipitant, though large quantities of this ore containing silver were bought and used by custom-smelters, who looked upon the manganese solely as a basic flux for silica. I believe that no other furnace has been obliged to trust this metal, and that the man ganese practice of Tombstone remains unique among the records of smelting lead-ores in the shaft-furnace. The bright side of the problem was given by the fact that the mines were shallow and that the enterprise would at least begin with oxidized ores. The tailings contained about 85 per cent. of silica,

Jan 1, 1895

Jan 1, 1930

By Edward Martinez

Although the copper segregation process has been known as a method for treating oxide copper ores since the 1920's, the reactions involved in this process are still a matter of conjecture. However, the evidence turned up in a recent series of experiments at Asarco's Central Research Laboratories strongly indicates that some of the proposed reactions may not be occurring. Experimental work on oxide copper ores from the Sagasca mines in Chile led to the discovery of the copper segregation process in 1923. It was found that the reduction of the copper with coal at about 700°C occurred on the surface of the coal instead of remaining disseminated in the ore. The unusual behavior of the copper, which caused it to migrate from the ore particles to the coal, was traced to the presence of a small quantity of sodium chloride occurring in the ore. Further experiments with oxide copper ores proved that the presence of a halide, either occurring naturally or admixed with the ore, caused the copper to migrate from the ore particles and to segregate in the charge.

Jan 8, 1966

By Norman F. Schulz

Relative fineness is an important characteristic of iron ore balling feeds. It is frequently expressed in terms of the Blaine Number which is determined by standardized permeametry procedures. Inconsistencies in Blaine Number specifications for balling feeds from different sources prompted an investigation of permeability methods. A revised procedure for permeametry tests was developed for use with conventional apparatus that yields an Effective Blaine Number which is similar to the Standard Blaine Number except that it more accurately describes the effective fineness of the actual test sample.

Jan 1, 1980

By D. A. Bailey, F. L. Kadey

During recent years, expanded perlite has found extensive use in a wide variety of commercial applications. Specifications for a range of uses call for aggregates having different physical properties and requiring various types of processing. The mitre scopic examination of expanded aggregates in specially prepared thin sections has yielded important information regarding internal structure and can be a useful aid in evaluation of the product. Perlite is an acid volcanic glass containing from 2 to 5 pct combined water. When crushed and rapidly raised to a temperature of 1500° to 2100°F, the volatilization of the combined water, coincident with softening of the siliceous glass, causes the particles to expand or pop. Expansion of perlite to densities as low as 1-1/2 lb per cu ft has been achieved, although the normal range is from about 2.5 to 10 lb per cu ft. Low-density materials of this nature have found application in cryogenic insula- tions, insulating tile and board, plaster and lightweight concrete, soil conditioners, filter aids after comminution, and a host of other uses. The expansion of perlite may be controlled by a number of variables. Some of these are ore milling, furnace design, expanding temperature, use of preheating techniques, screen size distribution, and feed rate of the crude. For the specific intended uses, the art of perlite expanding has developed to the point that much is known about the effect of these variables on the end product. The requirements, however, for an aggregate to be used in plaster are different from those for an expanded perlite to be used in lightweight concrete or for cryogenics. In the study of perlite, many practical questions remain unanswered. One of the most important is, "why do some perlites make hard aggregates while others cannot resist crushing or compaction?" The usual tests and methods for evaluation of nonmetallic substances have been tried and have contributed their share to our knowledge. But chemical analyses, compaction resistance tests, screen analysis, etc., will reveal only a limited amount of information. The answers to these complex questions may well be found in an examination of the intemal structure of the expanded particle. Such questions and the ex-

Jan 1, 1962

By Joseph J. Becker

RECENTLY the "oriented growth" hypothesis of recrystallization textures has been receiving considerable attention. According to this view, "whenever a new generation of grains is growing in a highly oriented matrix . . . one may assume . . . that from among available nuclei of a great variety of orientations those with suitable orientation relationship with respect to the matrix have by far the highest rate of growth (oriented growth) and will, therefore, predominate."' This statement includes primary recrystallization of single crystals and of polycrystalline materials showing strong deformation textures as particular cases. While the phenomenon of oriented growth undoubtedly does operate, and may be of importance in coarsening or secondary recrystallization, the writer feels that its extension to primary recrystallization is a different matter. Several aspects of this phenomenon may be pointed out which are difficult to rationalize on the basis of oriented growth. In recrystallizing deformed single crystals of alpha brass, Maddin, Mathewson, and Hibbard2 found that the twin composition planes of the recrystallized grains were parallel to the three operative slip planes they observed, and not to the fourth octahedral plane. The writer's current work seems to indicate further that when only one or two slip systems can be seen to operate, the recrystallized grains are aligned only with those slip planes actually observed. This behavior could hardly be accounted for by oriented growth, because on the latter basis the recrystallized texture of a deformed single crystal should certainly have the same symmetry as the crystal itself. Growth rates could not be expected to distinguish between crystallogra- phically equivalent directions, unless the presence of a visible slip system vastly increases the growth rate in the appropriate direction. This seems unlikely. These relationships were observed by the writer only when considerable care had been exercised before annealing to etch away the effects of cutting out the centers of tensile specimens with a jeweler's saw and to etch off the ends of compression specimens. When these.precautions were not taken, nu-cleation inevitably appeared to occur at the saw cuts or at the ends, and the resulting orientations never showed a [111] rotation but appeared quite random. The provision of many nuclei of many orientations did not enhance the correlation, but destroyed it. Recrystallization textures are sometimes strongly dependent on annealing temperature, which would imply that the anisotropy of growth rates is a suddenly varying function of temperature. This might be regarded as unlikely. Recrystallization textures can be strongly dependent on the degree of deformation. If textures are to be explained by selective growth from among nuclei of all orientations, it is difficult to see how the recrystallization process could have any dependence whatever on the manner or degree of deformation. It is felt that the above points should be considered before the oriented growth hypothesis is applied to primary recrystallization, with the necessary complete divorce of the mechanism of recrystallization from the details of the deformation process. References 1P. A. Beck and H. Hu: Reply to discussion of their paper on Recrystallization Texture and Coarsening Texture in High Purity Aluminum. Trans. AIME, 188, 1057; Journal oF Metals (Aug. 1950) TP 29083. 'R. Maddin, C. H. Mathewson, and W. R. Hibbard, Jr.: The Origin of Annealing Twins in Brass. Trans. AIME, 185, 655; Journal of Metals (Sept. 1949) TP 26763.

Jan 1, 1952

By James H. Boettcher, W. Durand Eppler

INTRODUCTION In the second quarter of 1979, Rapid Mining Co., Inc. ("Rapid") inquired whether Crocker National Bank ("CNB") would provide $4 million in term loan financing to help ("Dry Creek") acquire the outstanding shares of the Dry Creek Coal Company ("Dry Creek") in West Virginia. Prior to approaching CNB, Rapid had sought financing with the assistance of a financial advisor from a number of commercial banks without success. A summary of the initial terms requested by Rapid is shown in Table 1 compared with the actual terms on which the transaction closed. It is not difficult to note that the two sets of terms differ significantly. This is often the case when financing requests based on the expectations and vision of a mine developer are juxtaposed with more pragmatic requirements of a commercial bank. The "art" and fund of structuring financing plans for mining ventures (highly leveraged acquisitions or grass roots) comes in working with mine developers to arrive at a final financial structure that meets their objectives and constraints as well as those of the bank or other financial institutions providing much of the financing. Beginning with the terms requested by Rapid and ending with the terms that closed the transaction, this article briefly describes the process we went through with Rapid Mining. The Seller and Buyer The Dry Creek Coal Company was established in 1961, after its owner acquired the coal leases from Republic Steel. Republic has mined the primary coal seam from 1948-1961. Dry Creek was owned as a subchapter S corporation (i.e., for federal income tax purposes, income is taxed at the shareholder level) and had been run on a low key basis. Since the company had virtually no debt and limited cash needs, the owner produced primarily when rail cars were available and income was required. Output was therefore erratic as is shown in the top of Table II, but the result was a profitable little company with an attractive free cash position. Because the owner wished to retire and enjoy his wealth in a more readily spendable form, he had put the mine, with stated recoverable reserves of approximately 13 million tons, up for sale. In contrast, Rapid Coal's investors consisted of a number of investors of disparate financial situations. They had agreed upon a primary objective of income maximization and planned an annual production rate of 120,000 TPA which they and the current owner believed realizable. The Formulation of a Financing Structure Figure 1 presents a simplified overview of the sequence of steps taken in the financing process which lasted approximately three months from start to finish. Since banks see many requests for funding and considerble time is required to follow up on each, an important step was determining, after a brief review of the materials provided to us, whether the basic "eonomic entity" was viable. In this case, the size and quality of the reserves, the inherent operating cost characteristics, the sales arrangements, the management/labor situation and Rapid's principles all appeared to be sound enough to warrant investing the time necessary to do a thorough analysis of the project. Once this decision was made, the evaluation and analytic process shown in Figure 2 was initiated. The first and most fundamental concern of any banker is whether the loan will be paid back as scheduled from the cash flow generated by the project. The amount of debt relative to the owner's equity is of course crucial in such a determination. Before the debt/equity issue was addressed, however, a number of more qualitative factors had to be studied and if

Jan 1, 1985

By H. Carroll Weed

By caving a block into the workings of its open pit and using the block as an ore transfer, the lnspiration Consolidated Copper Co. has solved a transportation and sizing problem, making possible a great expansion of open-pit methods as applied to Inspiration ore-bodies. FROM 1915 to 1948 the entire production of Inspiration Consolidated Copper Co. was supplied from underground mining. The sole method used was block caving. Underground haulage and hoisting facilities were designed and geared to large-scale production. Beginning in 1948 open-pit mining was substituted for block caving in a portion of Inspiration's Live Oak orebody. The idea proved so attractive that before the Live Oak pit had come into production, another pit on the Colorado orebody (now the Thornton pit) had been laid out and stripping started. It should be noted that these orebodies were not new and the entire program was one of changed methods of mining. Since part of these orebodies had already been mined by block caving methods, it must be recognized that haulage levels had been established under the area or adjacent to it. The orebodies lay on the south side of Inspiration Ridge, while the shafts, crushers, and treatment plants are all on the north side of this ridge. The existing main crushing plant was designed to take a maximum of 12-in. material, and all ore was sized to this dimension by passing through grizzlies in the stopes. In the original planning for open-pit work much thought was given to the transfer of ore to existing underground levels for haulage and hoisting from the regular shafts. If this could be done the necessity of crossing the ridge could be eliminated. Final decision called for cutting a road through the ridge, installation of a primary crusher at an elevation of 3968 ft on the north side of the ridge, and railroad haulage with existing facilities to the main coarse crusher. This decision was brought about by the difficulties of properly sizing and transferring to underground haulage large tonnages of coarse breaking oxide which lay on the upper benches of the proposed pit. Trucking over the ridge on a 7 pct grade would give a cheaper and more flexible operation in handling this material. The benches in the pits are laid out at 50-ft inter-vals and designated according to elevation above sea level. The lowest bench in the original pit was laid out at 3500-ft elvation. All haulage roads are on a 7 pct grade and a vertical lift of 468 ft was considered about the maximum economically possible from a cost standpoint. After 2 years' operation the advantages of pit mining, both from the standpoint of costs and flexibility of operation, became more and more apparent. Studies were then started to develop the extension of open-pit mining to more of the ore reserve than had been planned originally. The idea of transfer raises was again explored. Obviously, as elevation of the pit was lowered, shorter transfer raises would be needed to reach the main haulage levels. Transportation from the lower elevations to the rim of the pit by belt conveyor or skip hoisting was also considered. However, it was recognized that sizing would be required both for conveying and regulation of feed size to the main crusher plant. This would necessitate a fixed or portable crusher located somewhere in the pit. It was known that the sulphide ore at the lower elevations was softer and easier to break than the overlying oxide of the upper benches. This sulphide ore is very suitable for grizzly sizing. Calculations indicated that for ore mined on 3650 elevation, costs for trucking to the primary crusher, crushing, and delivery by railroad to the coarse crusher would equal costs for dropping the same material to the 600 level, hauling underground, and hoisting directly to the coarse crusher bins, provided a suitable method of sizing and transferring could be developed. Above 3650 elevation costs would favor surface haulage; below they would favor underground haulage. The idea of caving an underground block from the 600 haulage level directly into the bottom of the pit

Jan 1, 1954

By J. Gurland

The strength variation ofWC-Co alloys with composition and particle spacing falls into two ranges. 1) Above a critical value of the mean free path, the strength follows a dispersion hardening relation; it is proportional to the volume fraction of WC and in-versely proportional to the particle size. 2) Below a critical value of the mean free path, the strength variation is based upon the Griffith criterion of fracture and is controlled by the case of crack propagation. The maximum strength is attained when the structure and load just satisfy the critical conditions for spontaneous crack propagation. THE relation between the strength and the structure of cemented carbides is of interest not only for its own sake but also for its contribution to the understanding of composite materials in general. The cemented carbides are essentially aggregates of a brittle carbide constituent and a ductile binder phase and, at certain structures of intermediate composition, the composite alloys attain strengths far higher than those of the separate constituents in bulk. It is this variation of strength with structure which will be discussed. The experimental procedures of sample preparation, mechanical testing, and quantitative metallo-graphic analysis have been described in Ref. 1. The reported strengths are the maximum fiber-stresses in bending calculated on the basis of completely elastic behavior. The plastic contribution to the over-all deformation is small and was neglected in the calculations (the elongation at fracture of the most ductile alloy, 50 pct WC-50 pct Co, is less than 0.5 pct).2 The pertinent structural parameters are: f, the volume fraction of tungsten carbide; p, the mean free path through the binder phase; the contiguity C, defined as the average fraction of surface area shared by a particle of wc with all neighboring particles of the same phase; and d, the average equivalent spherical diameter of the WC particles. The strength variation of WC-Co alloys with composition and particle spacing is shown in Fig. 1 and Table I, which are based partly on previously published data' and partly on new experimental work which extends the range to higher values of the mean free path. Each data point represents the average of five samples. For a given composition, the transverse rupture strength reaches a maximum

Jan 1, 1963

By J. J. Donos

IN the operation of a smelter, continuous and accurate determination of smoke losses is essential for purposes of metals inventories and as a check on the efficiency of smoke recovery apparatus. Previous to the development of a continuous and automatic smoke sampler by R. MacMichael, in 1924, two methods were in vogue, and still are in some smelters, for measuring solids passing out of a flue or stack. These are: (1) the so-called dust concentration method whereby the gas volume passing through the flue is first measured and then the total amount of solids carried in the smoke stream calculated from the weight of suspended matter filtered out of a measured volume of gas; (2) the balanced tube method is independent of gas volume flowing through the flue, and relies for its accuracy on the fact that a true smoke sample may be taken if the velocity of the gas in the sampling tube is constantly maintained at a known ratio of the average flue gas velocity. The total amount of solids passing through the flue is then proportional to the weight of filtered solids and to the ratio of the area of the flue to the area of the sampling tube, corrected for the velocity ratio. The limitations of the first method lie in the uncertainty of the varying volume of gas arising from metallurgical operations and the unreliability of ordinary gas meters to hold their accuracy under

Jan 1, 1951

By F. T. Davis

The annual review of mineral dressing was the subject of considerable discussion at the MBD meeting in New York last February. Because the amount of material now being published is so imposing, it was generally agreed that reviewers should try only to cite the items of importance. In order to conserve even more space, it was agreed to omit bibliographies. In reading these reviews, and those of the past two or three years, one is impressed by the advances in materials handling, the enlargement and the advances in automation of unit process equipment. Although there has been development of a variety of new concentration principles in flotation, magnetic separation, et al., the design of these principles into new plants has not been widespread. The probable reason is that the plants being built today are so large and costly that few are able to face the risk of any significant degree of experimentation. There are exceptions to this; for example, some of the chemical processes, but these are usually because there was no conventional process available. This situation should change in time as the ores amenable to our conventional methods become depleted.

Jan 2, 1967

By Arthur H. Leigh

Anode mud, the residual material collected from the bottom of the electrolytic cells during the refining of copper is leached, roasted, fire-refined and cast into Dore1 metal anodes. Dore1 metal is a gold-silver-copper alloy containing 80 percent silver. The metal is processed electrolytically using the Moebius system to refine silver and separate gold, platinum and palladium. The Moebius cell cathodes receive a deposit of silver crystals which are melted and cast into 1000 ounce silver bars with 999 Fine minimum purity. Gold mud is collected in fabric bags and cast into gold anodes for further refining in the Wohlwill cells. Wohlwill cells are unique in that gold, the noble metal, can be put into solution electrolytically without the use of aqua regia. Gold is collected on high purity gold foil cathodes and cast into 400 ounce bull ion with 999.7 Fine minimum purity. Platinum and palladium remain in the electrolyte progressively increasing in concentration and are finally separated and purified by precipitation.

Jan 1, 1973

By C. R. Boyd

WITHOUT attempting to do more than give a preliminary or skeleton report upon the geology and minerals of Southwestern Virginia at this time, I am led to hope that the great commercial importance of the sixty miles of cross-section here crudely treated of

Jan 1, 1877

By Wells A. Hutchins

Water laws important to the mining industry are those which govern or affect the right to use water, to dispose of water after using it in mining or milling, and to discharge waste material into water-courses. They include statutes and court decisions having general applicability, as well as others that pertain specifically to mining. THE INDUSTRY'S CONTRIBUTION TO WESTERN WATER LAW Despite sharp differences of opinion, the water law the Spaniards brought to the Southwest appears to have included some form of appropriation of water. The Mormons, who settled in Utah in the mid-nineteenth century, also developed a system of appropriative water titles. But by far the most profound impact on western water law was made by the gold- seekers who flocked to the Sierra Nevada foothills of California after the discovery of gold in 1848. Much of the gold was extracted from the ground by hydraulic or placer mining, and so the-miners' rights to the use of water became fundamentally important. Since there was no organized government in the foothills and no laws other than those made by the miners, they helped themselves to the land, the gold, and the water needed to work their claims.' They established and enforced regulations governing the acquirement and holding of mining claims and their rights to the water they needed.'In 1879 Justice Field, former Chief Justice of the California Supreme Court, spoke for the U. S. Supreme Court in saying that the miners were "emphatically the law-makers, as respects mining, upon the public lands in the State.""

Jan 2, 1960

By Martin Mayers

FIVE-SIXTHS of all the coal that is mined in the United States is burned, without previous treatment other than screening, for the produc-tion of heat and power, so that its value is fixed by its suitability for this purpose. Nevertheless, the characteristics of individual coals that determine their fitness for use in particular pieces of combustion equip-ment are not yet well known. This condition is due not only to the small extent of our knowledge concerning coal itself, but also to our compara-tive ignorance of the nature of the combustion process. The following paper is an analysis of the combustion process as it occurs in industrial furnaces, based largely on the results of laboratory research on combus-tion rates. From this analysis it is possible to determine the characteris-tics of the fuel that limit the capacity of a given piece of combustion equipment. Limitations imposed by other factors than the attainable speed of combustion will not be considered, since they are subject to a different type of analysis involving the balancing of maintenance costs against fixed charges. In order to observe the relations among the various factors that affect the speed of combustion, representative particles of fuel will be followed through two types of furnaces. A pulverized-coal furnace will be con-sidered first, because the independence of the individual particles facili-tates the analysis of the effect of furnace conditions. The second example will be a grate-fired furnace in which ignition of the fuel takes place on the underfeed principle. This includes both underfeed and chain grate stokers,(8)? but does not include hand-fired furnaces and some overfeed stokers. The furnace will be considered to be large enough, the tempera-ture high enough, and enough air provided, to burn the fuel completely, without, for the moment, specifying these quantities more completely.

Jan 1, 1934

By P. de Vitry, Willis P. Mould

THE wire saw is a tool not less than 60 years old, probably nearer 100 years old. It was developed in Europe and is reputed to have originated in Belgium. Frombold is said to be the original patentee. [ ] Wire sawing equipment, as indicated in Fig. I, is very simple. It consists of a three-strand wire cable, usually 3/16 or 1/4 in. in diameter, or a single flat ribbon of medium hard, tough, alloy steel twisted into a helix of those diameters, made to form an endless belt of any length up to several thousand feet. The wire is guided into the cut by sheaves mounted in slides on steel columns situated close to either end of the cut. The feed motion usually is controlled either by gravity or by hand-operated feed screws. The steel columns or "standards" range from 15 to 30 ft. in length. At the top is a swiveled arm supporting a sheave similar to the traveling sheave below. Immediately under the swivel-mounted sheave is a guy plate or collar with shackles attaching four chain or wire-rope guys with suitable tightening devices, or with two guys and two jack legs for supporting the standard vertically or at any desired angle. The usual drive is by a 10-hp. motor through a gear reducer, on which are mounted two grooved sheaves, one of which is keyed and the other free running on the shaft. Tension is provided by a car running on a track in line with the driving sheave

Jan 1, 1946

By Frank L. Antisell

Certain physical and chemical properties of copper are so intimately related that a change in variation of the physical properties indicates a certain chemical change. The standard specifications of copper of the American Society for Testing Materials are based upon physical characteristics with one exception, namely, the copper contents. The physical standard includes electrical properties, defects in the "set or casting," variation in dimensions, weight, etc. Paragraph 4 of the specifications states, " Wire bars, cakes, slabs and billets shall be substantially free from shrink holes, cold sets, pits, sloppy edges, concave tops, and similar defects in set or casting." Shrink holes and concave tops indicate both physical and metallurgical defects; cold sets, sloppy edges, etc., indicate physical defects only; small pit holes may be indicative of either or both physical and metallurgical defects, depending on conditions under which they originated. To the refiner, a copper casting, no matter how made, is known as a "shape," irrespective of whether it is wire bar, ingot, cake, slab, billet, etc. As practically all shapes are cast in an open mold, that is a mold without cope, the surface of the shape cools in contact with the atmosphere and has a coating of oxide. Certain phenomena of the surface indicate the adaptability of the metal for forging or rolling. The writer believes that it is much simpler to produce shapes that are metallurgically correct than those that are mechanically satisfactory. When copper is to be rolled into thin sheets or drawn into very fine wire, the slightest physical defect becomes evident. It is, therefore, of the utmost importance to consider every characteristic of the shape and ascertain the physical and chemical relationship. Pitch and Set.—The appearance of the surface of the copper when cooled is considered as to its "pitch," or the general contour of the surface of the shape (which may vary from a concave to a convex); and the '" set,"' or the detail appearance of the surface of the shape (the wave-like structure). When the shape presents a concave surface, it is known as "low pitch;" a convex surface is known as "high pitch" or "tough pitch;" and a level surface is called "flat pitch." The set of the copper is, in a very large measure, directly related to the pitch; and so intimately are

Jan 1, 1921

By C. P. Parsons

Caliper logging is a practice of measuring the variations in the diameter of the open hole in a well. This information is useful for many purposes, among which are: Determining the volumetric capacity of the portion of open hole to be cemented; the amount of gravel to be used for gravel-packing a well; the size and location of seat for a packer to be placed in a well; studying the effects of nitroglycerin shots; studying the effects of acidizing; studying the cause of drill-pipe failures; studying drilling technique; geological correlations. This is a new practice in oil fields and is eliminating considerable guesswork. Introduction Caliper logging of the open hole in oil wells, recently introduced and now showing initial results in many sections of the country, is providing information that is filling a long-felt need in oil-well cementing and in numerous other oil-field practices. Briefly, it measures the variations in diameter, of the open hole in a well. This direct physical measurement of the strati-graphic profile has considerable value for subsurface interpretations by the geologist, engineer, driller and others charged with the responsibility of properly completing and repairing oil and gas wells. The caliper shown in Fig. I is run into a well in closed position. The four arms are released when logging is to start. These arms are independent of each other. As the calipers are pulled upward through the open hole, the arms are like nimble fingers feeling the changing profile of the hole. This mechanical action is in turn converted into an electrical circuit, which is connected to a recording mechanism at the surface. a. Lowered into well in closed position. b. Arms released. Readings are made while caliper travels upward. Direct recording is made at surface, in inches. The recording of the diameter of the hole is directly in inches.

Jan 1, 1943

By C. P. Parsons

Caliper logging is a practice of measuring the variations in the diameter of the open hole in a well. This information is useful for many purposes, among which are: Determining the volumetric capacity of the portion of open hole to be cemented; the amount of gravel to be used for gravel-packing a well; the size and location of seat for a packer to be placed in a well; studying the effects of nitroglycerin shots; studying the effects of acidizing; studying the cause of drill-pipe failures; studying drilling technique; geological correlations. This is a new practice in oil fields and is eliminating considerable guesswork. Introduction Caliper logging of the open hole in oil wells, recently introduced and now showing initial results in many sections of the country, is providing information that is filling a long-felt need in oil-well cementing and in numerous other oil-field practices. Briefly, it measures the variations in diameter, of the open hole in a well. This direct physical measurement of the strati-graphic profile has considerable value for subsurface interpretations by the geologist, engineer, driller and others charged with the responsibility of properly completing and repairing oil and gas wells. The caliper shown in Fig. I is run into a well in closed position. The four arms are released when logging is to start. These arms are independent of each other. As the calipers are pulled upward through the open hole, the arms are like nimble fingers feeling the changing profile of the hole. This mechanical action is in turn converted into an electrical circuit, which is connected to a recording mechanism at the surface. a. Lowered into well in closed position. b. Arms released. Readings are made while caliper travels upward. Direct recording is made at surface, in inches. The recording of the diameter of the hole is directly in inches.

Jan 1, 1943

By Thomas R. Couzens

Jan 1, 1985