Search Documents

By M. C. Flemings, T. S. Piwonka

Pore formation is examined analytically in cellu-larly solidified single crystals, in cylindrical castings of pure metals and alloys, and in unidirectionally solidified castings. Effects are considered of fluid flow. dissolved gas, and surface tension. Experimental results show that flow through a partially solid "mushy" aluminum alloy obeys relations similar to those applicable for flow through other types of porous beds. Flow rate is proportional to the square of the fraction liquid (fL) for fL less than 0.3. Results indicate models chosen for mathematical description of pore formation in alloy solidification are valid. ONE of the solidification variables which is influential in determining mechanical properties of castings and of wrought material produced from cast ingots is porosity. This porosity may result from shrinkage, dissolved gases, or a combination of both, and may take the form of either macroscopic pores in localized areas of the casting or microporosity evenly distributed throughout large areas of the casting. In alloys which freeze over a range of temperatures some microporosity is generally found after solidification. There has been much discussion as to whether the micropores are caused primarily by shrinkage, by gas, or by a combination of both.'-3 There has, however, been little experimental or analytical work performed to delineate the relative contributions of shrinkage and gas in causing microporosity or to quantitatively describe the influence of processing variables on microporosity. Porosity other than microporosity (e.g., center line shrinkage) has also received only limited quantitative treatment.495 The aim of this work is to examine analytically the general problem of pore formation in solidification and to perform limited confirmatory experiments. Consideration is first given to shrinkage porosity in pure and nearly pure metals (shrinkage in cellular growth, centerline shrinkage in cylinders). Next, a discussion is given of formation of shrinkage-caused microporosity in unidirectional solidification and in "mushy" solidification. Finally, influences of dissolved gas and surface tension on microporosity are examined. Numerical results are given for aluminum and an aluminum alloy. Typical examples of microporosity are shown in Figs. 1 to 3, for 1) cellularly solidified aluminum, 2) sand-cast aluminum alloy, and 3) low alloy steel. SHRINKAGE POROSITY IN PURE AND NEARLY PURE METALS 1) Cellular Growth. In cellular freezing of an impure liquid, liquid grooves may exist over a considerable length of the growing crystal.6 The cross-sectional area of the grooves decreases with increasing distance from the cell tips; the root of the groove is blunt if the liquid at this point reaches eutectic composition. As a result of volume contraction during solidification, flow occurs down the groove, parallel to the growth direction; hence, there must be a pressure drop from the groove entrance to points within the groove. The geometry of the groove is simplified to that of a circular cylinder of radius r and length L, Fig. 4, L » r, and a simple and useful limiting case is obtained. This is that, in the circular cylinder freezing at constant velocity, the pressure at the root of the groove is lower than that pressure at radius r in grooves of other geometries where r decreases continuously to a lower limit at L. As discussed below, a pore resulting from a given pressure difference

Jan 1, 1967

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1941 are available at Institute headquarters, unless otherwise noted They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS TECHNICAL PUBLICATIONS in Classes A-Metal Mining, 13-Milling and Concentration, H-Industrial Minerals, and I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month Technical Publications in Classes C-Iron and Steel Division, D-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly TECHNICAL PUBLICATIONS in Class G-Petroleum Division are distributed in PETROLEUM TECHNOLOGY, which is issued every other month TECHNICAL PUBLICATIONS in Classes F-Coal Division, J-Mineral Industry Education Division, K-Mining Administration, and L-Geophysics, are issued as separate pamphlets An Institute member is entitled to one copy of any printed TECHNICAL PUBLICATION or CONTRIBUTION Copies of TECHNICAL PUBLICATIONS listed have been mailed to members of the Institute according to their registration by classes CONTRIBUTIONS and other TECHNICAL PUBLICATIONS will be sent upon request A member may purchase an additional copy of a TECHNICAL PUBLICATION or a CONTRIBUTION at one cent a page, minimum charge, 25¢ Nonmembers may purchase any CONTRIBUTION or a TECHNICAL PUBLICATION of the F, J, K, or L classes at the same rate, but the nonmember price per copy for METALS TECHNOLOGY, MINING TECHNOLOGY or PETROLEUM TECHNOLOGY is $1 25 domestic, $1 35 foreign countries. TECHNICAL PUBLICATIONS (separate pamphlet form), $2 per annum domestic, $2 50 foreign. METALS TECHNOLOGY, $7 per annum domestic, $7 80 foreign (Iron and Steel Division and Institute of Metals Division ferrous and nonferrous papers) MINING TECHNOLOGY, $6 per annum domestic, $6 60 foreign (metal mining, milling and concentration, Industrial Minerals Division, and mining geology papers) PETROLEUM TECHNOLOGY, $6 per annum domestic, $6 60 foreign Bound volumes have been mailed to members that have requested them, and MINING and METALLURGY Is mailed each month A member is entitled to one volume a year on his membership and he may purchase for $2 50 one copy of a volume not already received, additional copies of the same volume, $5 Nonmembers in the United States may purchase the volumes listed at $5 each, outside of the United States and its possessions, $5 6o Extra single copies of MINING AND METALLURGY, 25¢ current issue, back numbers 500 each to members, to nonmembers 50¢ current issue and $1 each, back issues Subscription price to nonmembers and to members for extra copies, $3 per annum domestic, $4 00 foreign.

Jan 1, 1941

By A. Lawley, H. W. Schadler

TWINNING has long been recognized as a possible mode of deformation in crystalline solids and has been studied in a wide variety of crystals.&apos; Recently, deformation markings which have the topographical characteristics of twins have been seen in tungsten" and the body-centered cubic alloys of tungsten and molybdenum with rhenium.3-7 These markings have been identified as twins because: 1) they are visible after polishing and etching;2,3 2) their formation is accompanied by an audible click and a drop in load;4 and 3) the habit plane is {112}, the plane which has been identified as the twinning plane for several body-centered cubic metals.&apos; However, there has been no published evidence for the specific determination of the twinning direction in rhenium alloys of tungsten and molybdenum, because usually the deformation twins were not broad enough to be detected with a conventional X-ray beam. Consequently, [111] is inferred as the twinning direction since the latter must lie in a plane of symmetry perpendicular to the twinning plane (112). As Sims and Jaffee3 and Lawley and Maddin4 have shown, the addition of rhenium to molybdenum and tungsten increases the ductility of the alloy over that of the pure metal, but twinning is much more profuse in these alloys than in the pure elements, particularly at Mo-35 pct Re*and W-30 pct Re. Since twinning is often associated with brittle fracture in iron8 and the silicon-irons,9 direct experimental proof that the deformation markings in tungsten and molybdenum alloys of rhenium are twins seemed to be needed. Using the Laue back-reflection technique, the deformation markings in a Mo-35 pct Re alloy are shown to be deformation twins. The twins have a (112) habit plane and the twinning direction is <111>. The Mo-35 pct Re specimen used was taken from a 0.060-in. zone-refined single crystal deformed 6 pct in tension at 78°K. The Laue back-reflection technique, with a film to specimen distance of 2 cm, and white radiation from a copper target were used.

Jan 1, 1962

By A. J. Sedriks

ALTHOUGH the occurrence of a readily visible tarnish on the stress-corrosion fracture surfaces of titanium alloys tested in oxygenated nitrogen tetrox-ide solutions has been reported,&apos; the possibility that the formation of this tarnish is a requirement for cracking to proceed does not appear to have been considered. It has been proposed that failure occurs in this system as a result of some electrochemical-mechanical process.2 However, recent studies3-6 of the stress-corrosion cracking of a brass in certain ammoniacal solutions, which also cause visible tarnishing, have led to the view that failure occurs by the repeated formation and fracture of a brittle surface film of cuprous oxide. The purpose of this note is to point out the similarities which exist between the tarnish which forms on a brass and that found on titanium alloys failed in nitrogen tetroxide, and to suggest, by analogy, that a similar tarnish-rupture mechanism may be operative in the latter case. The titanium alloy selected for the present study contained 5.2 pct Al, 2.5 pct Sn, 0.025 pct C, 0.16 pct Fe, 0.014 pct N, 0.012 pct H, 0.07 pct 0, and 0.002 pct Mn by weight. Vacuum-annealed alloy strips measuring 4 by 0.25 by 0.04 in. were used to prepare self-stressed test specimens. Each specimen was made from two strips by bending the end portions and spot welding them together to produce curved sections of uniform bending stress. (The exact details of preparing such specimens have been described by Lisagor el al.7) The curvature in the strips determines the ma-magnitude of the outer fiber stress, which in the present specimens was 100,000 psi (yield stress = 120,000 psi). The specimen surface in the spot-welded end regions was shot-peened to induce compressive stresses and thereby eliminate the possibility of stress-corrosion cracking in these regions. The test environment was nitrogen tetroxide, initially containing 99.5 pct N2O4, 0.1 pct H2O, and 0.08 pct C1, through which oxygen had been bubbled for 30 min. During testing the tetroxide was subject to an oxygen pressure of 250 psi. The duration of the test was 96 hr, and during this time stress-corrosion cracks propagated through some 50 pct of the thickness of the specimens. After testing, the tarnish was liberated from the fracture surface by immersion in a methanol-5 pct bromine solution, and then examined by electron dif- fraction and transmission electron microscopy using a JEM-7 electron microscope. The possibility that the bromine solution had affected the structure of the tarnish was investigated by an "in silu" examination of the stress-corrosion fracture surface using a reflection electron diffraction attachment designed for handling bulk specimens. Typical areas of the tarnish liberated by the me-thanol-bromine solution are shown in Fig. 1. Fig. l(a) reveals that the tarnish consists of individual platelets, and from Fig. l(b) it can be seen that the platelets are joined together to form a semicontinuous film, the boundaries of the titanium substrate grains being retained in the tarnish. Electron-diffraction patterns taken from these areas exhibited diffraction spots typical of a monocrystal. The diffraction pattern shown in Fig. 2 was taken from the central area in Fig. l(n). Monocrystal patterns obtained from areas containing numerous individual platelets can only be explained by assuming that their growth is governed by the titanium substrate (i.e., their growth is epitaxial). In other areas, the tarnish had folded over or became mechanically damaged, and these areas gave diffraction patterns consisting of "spotted" rings, enabling interplanar spacings of the tarnish lattice to be determined. These spacings, measured using a

Jan 1, 1968

Aamot, Olav Crone, Chem. Engr., Norsk Elektrokemisk, Kongensgt. 18, Olso. Norway. &apos;29 Abadilla.-Quirico A., Dir., Bureau of Mines Manila, P. I. &apos;38 Abbott, Clarence E., V.P., Charge of Raw Materials, Tennessee Coal, Iron & R.R. Co., 1212 Brown-Marx Bldg., Birmingham, Ala. &apos;04 Abel, Raymond L., Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh, Pa. &apos;29 Abel. Walter D., Cons. Engr 1839 Holmby Ave., W. Los Angeles. Calif. &apos;32 Abele, Louis T R. F. D. 5. Susquehanna Trail, N., York. Pa. &apos;31 Abell, Leo M., Ore Dressing Investigator, School of Mines Adelaide, S. Australia. &apos;31 Abenius. Hakan V., Mine Supt., Bolidens Gruvaktiebolag Boliden, Sweden. &apos;37 Aborn, Robert H., Asst Met., Research Lab., U. S. Steel Corp. Lincoln Highway, Kearny, N. J. &apos;19 Abraham, W. E. V., East India United Service-Club, 16 St. James&apos; Sq., London, S. W. 1, England. &apos;28 Abrams. Charles Jackson 1624 17th St., Denver, Colo. &apos;36 Abstein, Henry T., Engr. & Mgr., Profile-Tamarack Mines Co Yellow Pine, Idaho. &apos;27

Jan 1, 1938

Jan 1, 1879

By N. T. Burdine

Formulas for calculating relative permeability from pore size distribution data are derived from basic laws of fluid flow ill porous media. The tortuosity factors that appear in the equation5 are described in. terms of the physical properties of tile medium and the saturations of the contained fluids. Procedures for calculating and methods for measuring the tortuosity factors are discussed. Values of relative permeability calculated by the formulas art: compared with results obtained by experimental measurements I INTRODUCTION Recently, several investigators have derived relative permeability equations from Darey&apos;s and Poisenille&apos;s Laws in which some, physical factor or factors describing the porous system appear. The factor that has caused the greatest amount of comment, and which is probably least understood, is the tortuosity of the fluid {lath ill the porous sample. Values of the tortuosity factors appearing in the equations range from a constant for all condition- of the fluid flow system to an inverse function of the pore radii. It is the purpose of this paper to compare wine experi~i~cntslly determined relative permeability curves with those calculated by a method which utilized capillary pressure infortmation. The capillary pressure data were obtained prefer.. ably from pore size distribution information as determined by mercury injection but. in some cases, in the absence of suitable mercury injection information. data were taken from measurements made by the porous semi-permeable diaphragm method. The physical significance of certain tortuosity concepts is inferred and the determinations of the tortuosity factors from pore size distribution data and by electrical measurements are discussed. THEORETICAL BACKGROUND In previously reported studies on pore size distribution in petroleum reservoir rocks. by the author and co-workers ail equation was derived relating specific permeability. k, to pore entry radii, R, porosity. . tortuosity factor. .,, and incremental pore volume. V. The equation is where being the "effective" length of the flow path in the porous sample. and L the length of the porous sample., The constant. 0.126. is a units conversion factor. (This definition of tortuosity factor X, = L L does not conform to all such definitions found in the literature. Fly similarity, in a two-phase system. the effective permeability of the wetting-phase.

Jan 1, 1953

By M. E. Wadsworth, R. C. Peterson, W. M. Fassell

The temperature and pressure dependence of the reaction of tantalum in oxygen were investigated from 500° to 1000°C at pressures from 10 mm Hg to 600 psi total oxygen pressure. Tantalum was found to oxidize linearly under the above conditions. Three distinct regions of temperature dependence were found with different energies of activation. From 500° to 600°C the rate of oxidation of tantalum was found to be essentially independent of the oxygen pressure at the pressure investigated. The oxidation rate increases rapidly with an increase in pressure from 600&apos; to 800°C. The dependence of the oxidation rate on the bulk concentration may be expressed by V = k&apos;?, where k&apos; is the specific rate constant and ?=k1Co2/(l + K1Co2), where k, is the equilibrium constant for the adsorption of oxygen on tantalum. ONLY a limited amount of data has been presented in the literature on the oxidation behavior of tantalum metal. Some values of its oxidation rate were reported in the Corroston Handbook&apos; and by McAdams and Geil.&apos; The first extensive investigation of tantalum was the work of Gulbransen and Andrews." They determined the reaction rates of tantalum in O2 and N2. Their results indicate that this metal follows the parabolic law in the temperature range of 250" to 450°C in O2 at pressures of 7.6 cm Hg with an activation energy of 27,400 cal per mol. In nitrogen, the metal follows the parabolic law from 500" to 800°C at 7.6 cm pressure. All experimental determinations were of 2 hr or less duration and deviations from the parabolic rate conceivably could occur at longer times. A spectrophotometric study of the oxidation of tantalum by Waber, Sturdy, Wise, and Tipton&apos; indicated good agreement between this method and the microbalance technique. The experiments were conducted in air from 220" to 350°C. The metal was found to follow the logarithmic law up to 320°C and the parabolic law at higher temperatures. The activation energies in the logarithmic region were reported as 12.57 kcal per mol and 12.0 kcal per mol, respectively, for the microgravimetric and spectrophotometric methods. In the parabolic region the activation energy was found to be 27.2 kcal per mol, in good agreement with the value of Gulbransen and Andrews." The present paper is concerned with the behavior of tantalum from 500" to 1000°C in oxygen at pressures ranging from 1/2 to 40.8 atm pressure. Earlier preliminary data by McKewan5,6 indicated the following facts concerning the behavior of tantalum: 1—At temperatures from 500" to 600°C, the metal followed the linear law. 2—At 575°C the rate of oxidation was found to increase with O2 pressure. 3—The Arrhenius plot in this temperature region was nonlinear. The nonlinearity of the Arrhenius plot was indicative of a more complex behavior than originally suspected for this metal.

Jan 1, 1955

By A. Totani, S. Nakajima, H. Okazaki

The phase diagram for the SnTe-SnSe system has been studied in the temperature range from 300° to 900°C by differential thermal and quenching techniques. The X-ray measurements were made on quenched specimens. High-temperature diffraction was also made to study the phase transition in SnSe. The system is proved to be of a eutectic type in which no intermetallic compound exists. The eutectic point is at the composition SnTeo.55 Seo.45. the eutectic temperature being 755°C. Solid solubility limits are SnTeo.6Seo.r and SnT eo. 3s Seo.6s at the eutectic temperature, and change almost linearly to SnTeo.aaSeo.lz and SnTeo.18 Seo.az as temperature decreases to 300°C. It was shown that the SnSe phase has a phase transition of the second order at about 540°C and that the transition temperature decreases with increase of the SnTe content. THERMOELECTRIC properties of tin telluride (SnTe) and tin selenide (SnSe) have been studied extensively in recent years. The variation of physical properties with composition could be of interest if these compounds form an appreciable crystalline solution. The purpose of present investigation is to confirm the formation of crystalline solution or intermetallic compound, if any, and to establish the phase diagram for this system. The crystal structure of SnTe is NaCl type with a cubic unit cell1 (a = 6.313A). The crystal of SnSe having an orthorh2mbic unit cellz (a = 11.496, b = 4.1510, and c = 4.4437A) is isomorphous with tin sulfide (SnS) which has a distorted sodium chloride structure. It has been known that SnSe has a phase at at 540°C; the transition has been assumed to be of the second order. As far as we know, only two studies on the SnTe-SnSe pseudobinary system have been reported. The conclusion obtained in these papers is that, in the composition regions near SnTe and SnSe, the system forms a crystalline solution of the SnTe structure and the SnSe structure, respectively, and that, in the intermediate region, both phases coexist. However, neither the variation of the solid solubility vs the temperature nor the liquidus and solidus were investigated. Hence present writers have attempted to determine the phase diagram of the system by differential thermal analysis (D.T.A.) and X-ray diffraction. EXPERIMENTAL Sample Preparation. Starting materials, SnTe and SnSe, were prepared by the direct fusion of commercially available high-purity (99.999 pct) elements. Stoichiometric amounts of each couple Sn-Te or Sn-Se were weighed into a clear fused silica ampule. After evacuation to a pressure below 10-3 mm Hg, the am- pule was sealed, and annealed at 900°C for 5 hr. The melt was quenched in water. X-ray analysis confirmed the formation of a single phase of SnTe or SnSe. The other samples, SnTel-,Sex were synthesized from these SnTe and SnSe by mixing them in the required ratio, followed by annealing at 900°C and quenching. These samples were used directly for D.T.A. For X-ray measurements, samples were annealed at 700°, 600°, or 500°C for 100 hr or at 300°C for 150 hr, and then quenched in water. It was found that the lattice constants of the SnTe phase annealed for 150 hr at temperatures above 500°C did not differ from those annealed for 100 hr at the same temperatures. However the X-ray phase analysis showed that at 300°C the annealing for 150 hr was necessary to attain a true equilibrium state. D.T.A. The solid-liquid equilibrium temperature was determined from D.T.A. measurements. The sample was sealed in an evacuated silica tube and molybdenum powders sealed in an another tube were used as a reference material. The sample and the reference tube were placed in a nickel block and were heated from room temperature to 900°C at a rate of 3°C per min and then cooled down at the same rate to 600°C. Thermocouples for these measurements were Pt-Pt. Rh (10 pct) and the error of temperature measurements was within + l0C. D.T.A. curves were obtained on a two-pen recorder and an automatic controller (PID type) was used for the program of heating and cooling. When temperature reaches the solidus from the low-temperature side, there appears an endothermic peak. The solidus temperature was determined by extrapolation of the straight portion of the starting flank of this peak to the base line. In a similar way, the liquidus temperature was determined from an exothermic peak on D.T.A. cooling curve. In the case of supercooling, if any, its degree can be estimated from the magnitude of the abrupt temperature rise. X-Ray . X-ray powder patterns were taken by a diffractometer using CuK, radiation. Since the SnSe crystal is cleaved easily, the powders become flaky when SnSe-rich samples are ground in an agate

Jan 1, 1969

By ELIHU THOMSON

IN 1877, Professor Thomson delivered at the Franklin Institute, [Philadelphia, five lectures on electricity. The object of the lectures and the demonstrations, which were numerous and many of them original even to the employment of special apparatus constructed by the lecturer, was to show clearly that electricity, of whatever name, was the same., differing only in tension (as it was termed) and in the current flowing, or quantity (the old term), in steadiness or in wave-like character. In those days, the textbooks divided the subject into statical and dynamic electricity, with sub-divisions such as frictional electricity, voltaic electricity, magneto electricity, electromagnetism, thermo electricity, and animal electricity. The well-known Ruhmkorff coil,&apos; or spark coil as it is now called (as when used for the ignition of automobiles), was employed to step, up a battery current to a high-tension discharge which would charge condensers, such as Leyden jars.

Jan 1, 1921

CONTENTS PAGE CARMICHAEL, NORMAN, and KIDDIE, JOHN.-Development of Mine Transportation in Clifton-Morenci District. Discussed by Norman Carmichael, Charles Legrand, B. B. Gottsberger 1 BARER, THOMAS C.-Fresnillo - Glory-hole Mining Practice. Discussed by Charles A. Mitke, B. B. Gottsberger, E. R. Thomas, Enoch Perkins..: 3 BRADLEY, P. R.-Estimation of Ore Reserves and Mining Methods in Alaska Juneau Mine. Discussed by R. M. Raymond, A. H. Rogers, Enoch Perkins, H. G. Moulton 6 BIRCH, STEPHEN.-Geology and Mining Methods of the Kennecott and Beatson Mines. Discussed by R. M. Raymond, Alan M. Bateman, Enoch Perkins 8 LEES, CHARLES E.-Mining Methods and Costs at the Iron Cap Copper Co., Copper Hill, Ariz. Discussed by A. L. Walker, A. Neustaedter 10 BELL, CHARLES N. -Mining Methods of the Telluride District. Discussed by Charles S. Hurter 10 Development of Mine Transportation in Clifton-Morenci District Discussion of the paper of NORMAN CARMICHAEL and JOHN KIDDIE, presented at the New York Meeting, February, 1924, and issued, as. Paper No. 1310-M, with MINING AND METALLURGY, March, 1924. NORMAN CARMICHAEL.-We realized the objections too the gable-bottom car, but were almost forced to its adoption by the same reasons that caused us to retain the 20-in. gage. To use another car would have meant a vast number of changes, for our transportation system was quite extensive; all mine chutes and ore bins were arranged for that car. Had we been laying out, new works, many of our decisions would have been different. MEMBER.-If you were planning it now, would you not put in box bottom cars with a rotary dump? NORMAN CARMICHAEL.-We surely would. One objection to the gable-bottom car is the spill. No, matter how carefully the cars are kept up,: there is always leakage and spill. The cost of keeping and maintaining the cars in a good state of repair, so as to keep that loss at a minimum, is not necessary for a box-bottom car.

Jan 6, 1924

In a letter to Prof. L. P. Breckenridge, chairman, urging the continua-tion of the Fuel Conservation Committee of the Engineering Council, Edwin Ludlow calls attention to the millions of tons of culm in the an-thracite region that can be utilized in properly equipped plants and the electricity generated transmitted to. New York, Philadelphia, and other nearby cities. He says: "Experiments have shown the economic value of No. 4 Buckwheat, which passes through a 1/16-in. mesh and over a 1/32-in. mesh. Culm passing through a 1/32-in- mesh is pulverized until it passes through a 300 mesh and is then burned under boilers. Two plants of this kind are now in successful operation in the anthracite region. Another rather interesting experiment was using 30 per cent. of this pulverized coal with 70 per cent. of oil in the generation of steam in the place of pure oil. This utilization of the fine anthracite, which has always been a waste product and thrown away, is not only fuel conservation in its truest sense but in the case of a bituminous strike, when no strike is contemplated in the anthracite field, will furnish fuel to manufacturing plants that otherwise would be obliged to shut down."

Jan 12, 1919

By John H. Schissler

INTRODUCTION AND SUMMARY Complex copper-lead-zinc ore is mined from underground workings high in the Western Cordillera of the Andes mountains about 100 km in a stralght line north of the city of Arequipa in southern Peru. The Madrigal mine is situated in a steep-walled canyon into which the six operating levels "daylight". Production is from cut-and-fill stopes currently producing approximately 740 dry metric tons per day. The Santa Rosa vein, the most important producer in the district, outcrops for a distance of about 4 km, bearing N 75º W and dipping about 70º NE. In places the vein splits into two or three branches; widths of each vary between 1 and 4 m and total mineralized widths of up to over 8 m occur. Principal ore minerals are chalcopyrite, galena and sphalerite. Ore reserve grades for the Madrigal mine average about 1.45% Cu, 2.6% Pb and 5.0% Zn, 2.9 ozAg per metric ton. [Compania] Minera del Madrigal is a California limited partnership; the general partner and operator is [Compania] Madrigal, a wholly-owned subsidiary of Homestake Mining Company. HISTORY Shallow workings found on the Santa Rosa vein were probably made by the Spaniards during colonial times in their search for

Jan 1, 1977

By B. Yarar, J. Kaoma

[Introduction The critical surface tension of wetting of hydrophobic materials has been investigated extensively by Zisman et al. (1973) and relates the spreading of a liquid on a solid to the surface tension of this liquid. Thus, the Zisman ap¬proach shows that a plot of Cos 0 versus ?LV where, 0 is the contact angle and ?LV is the surface tension of that liquid in contact with its own vapor at equilibrium, produces a straight line which can be extrapolated to Cos 0 = 1. The intercept corresponds to a given ?LV, termed the critical surface tension of wetting. In instances, however, Cos 0 - ?LV plots show deviations from linearity. Alternative approaches have also included the plotting of adhesion tension (YLV COs 0) versus ?LV that can be interpreted in terms of critical surface tension data (Lucassen-Reynders, 1963). It has, on the other hand, been customary to correlate contact angle (0) with flotation data, although it is recognized that surface inhomogeneities and related contact angle hysteresis limit the interpretations pertaining to solid surface structures purely based on contact angle measurements. It is nonetheless true that 0 = 0, when the liquid is water, corresponds to a hydrophilic solid. Determination of ?c by contact angle measurements in conformity with the Zisman approach can encounter experimental difficulties, especially when solids are in a powder form. Following the reasoning that 0 = 0 corresponds to the hydrophilic state of a solid, froth flotation experiments can be expected to produce critical surface tension of wetting values for powders. The technique that consists of plotting recovery (% R) versus YLV data and extrapolating the linear part of the curve to % R = 0, has been described elsewhere (Yarar and Kaoma, 1984). This paper describes some of the results obtained by the extrapolation technique mentioned above, using various sulfide minerals. Experimental Materials Molybdenite (MoS2), sphalerite (ZnS), chalcopyrite (CuFeS2), chalcocite (Cu2S), and galena (PbS) were handsorted from massive samples and ground by mortar and pestle, and the -147 Fan fraction used in experiments; sulfur (S) was a C.P. Fisher Scientific Co. product. Method One gram powder samples were conditioned for three minutes in methanol-water solutions of predetermined surface tension values and the percents recovered by flotation using a Partridge-Smith Cell (Partridge and Smith, 1972), were plotted against each ?LV value. Results and Discussion The percent recovery versus ?LV for two naturally hydrophobic solids, i.e., natural molybdenite, MoS2 and sulfur are given in Fig. 1 where it is seen that ?c for sulfur is obtained as 31.5 mNm-1 whereas for MoS2, it is 26 mNm-1. Figure 1 also shows that the new flotation technique described, for estimating ?c is in good agreement with the Zisman method. Curves obtained by the same method for the minerals Cu2S, PbS, and ZnS are given in Fig. 2, where it is seen that for Cu2S, ZnS, and PbS, the extrapolation to % R = 0 produces ?c values of 36, 39, and 49 mNm-1, respectively. CuFeS2, on the other hand, gives a curve that does not permit such an extrapolation to obtain a ?c value with certainty. Nonetheless, treatment of the powder with 8.95 X 10-5 molar Na2S solution followed by washing with distilled water prior to flotation effects the curves as shown in the insert of Fig. 2. The type of curves given in Fig. 1 appear to be typical of hydrophobic solids as can also be observed in Fig. 3. The composition of solid and minute quantities of inclusions seem to play an important role as regards the surface properties of solids as reflected by the slope of the linear part of the % R - ?LV plot and thus the value of ?c obtained by this technique. For example, MoS2 of three different stoichiometric compositions produced the data given below. [MoS2MoS2.14Mo1.002S2 ?c mNm-126.029.031.0 dR/d?8.95.23.0]]

Jan 1, 1985

By H. B. Bell, P. C. Lidster

A study has been made of the use of ThO2-Y2O3 solid electrolytes to determine activity of chromium in Fe-Cr and Ni-Cr alloys in the temperature range 1300° to 1700°K. This method has been shown to give results which agree with the best vapor pressure measurements. SEVERAL investigations1"5 have been made of chromium activities in Fe-Cr alloys. Most of these have been made by vapor pressure measurements using knudsen cell techniques while one has been made using gas equilibration with H2/H2O gas mixtures. In the present investigation electromotive force measurements have been made on this system using a thoria yttria solid electrolyte. This system was -chosen to establish the technique of measurement at low oxygen potentials, before extending it to Fe-Ni-Cr alloys. The cell used was Pt Cr • Cr2O3 ilThO2 • Y2O3 llalloy • Cr2O3 IPt Since the oxygen pressure of the chromium-chromic oxide mixture lay in the range 10"19 to 1027 atm in the temperature range investigated, thoria yttria electrolytes were used. It was soon found during the investigation that considerable care was required to prepare satisfactory electrolytes and a study was made to find the best method of preparing pellets of TI1O2-Y2O3 solid solution of as near theoretical density as possible. Various compositions in the range 2 to 15 mole pct Y2O3 were studied but the experimental measurements were made with electrolytes containing 4 to 5 pct Y2O3. The method of preparation finally adopted was to use thorium oxalate and yttria as raw materials. The thorium oxalate was decomposed at 900°C for 6 hr to give a reactive powder. This powder was then mixed with the appropriate amount of yttria and ground in an agate mortar for about 4 hr. The powder was moistened with absolute alcohol as a lubricant and pressed in a metal die at a pressure of 7 tons per sq in. The pellets were then heated at 1100°C for 24 hr followed by 24 hr at 1250°C. After this firing cycle the material was reground and repelleted and again fired at 1100° and 1250°C followed by heating for 7 days at 1600°C. It was found in later experiments that a further firing of 4 hr at 2000°C improved the density further and gave pellets of only 2 pct porosity. After firing, the pellets were polished on emery paper and finally with the 2 µ diamond paste. The polishing was followed by a final firing of 24 hr at 1500°C. Investigation showed that this final treatment minimized reaction between the electrolytes and chromium oxide. It was believed that this was because of a lowering of the surface energy of the electrolyte surface. Two types of investigation were carried out to check that the pellets were satisfactory oxygen ion elec-

Jan 1, 1970

THE Institute met on Wednesday evening, May 22d, in the parlor of the Stanton House, Dr. T. Sterry Hunt, President, in the chair. The President delivered an introductory address on the Brown Hematite Deposits of the Great Valley, after which the following papers were read and discussed : Note on the Result of an Experiment with the Wheeler Process of Combining Iron and Steel in the Head of a Rail, by W. E. C. Coxe, of Reading, Pa. On the Jenks Corundum Mine, Macon County, N. C., by Dr. R. W. Raymond, of New York City. On Wednesday afternoon, previous to the opening session, the members who had already arrived in Chattanooga, were taken by the Local Committee to the works of the Roane Iron Company, and Chattanooga Iron Company, and then to the top of Lookout Mountain, where, at the request of the members present, Dr. Hunt described the geological and geographical features of the Chattanooga region, with the magnificent panorama spread out before them as a map. On Thursday morning an excursion was made by steamboat down the Tennessee River as far as Shellmound. Here cars were taken to the coal mines of the Dade Coal Company, where the members were courteously received by Mr. E. B. Wells, the Superintendent. After a trip through the mines the party partook of a collation provided by the company. South Pittsburgh, on the Tennessee River, was next visited, where the Southern States Coal, Iron and Land Company have a large blast-furnace plant in the course of erection. After conducting the party through the works, shops, etc., Mr. James Bowron, the manager, entertained the members with graceful hospitality at dinner. The second session was held on Thursday evening for the transaction of business. The President, Dr. T. Sterry Hunt, appointed Messrs. W. E. C. Coxe, R. H. Richards, and F. J. Slade, scrutineers, to examine the ballots for officers for the ensuing year.

Jan 1, 1879

By Anthony F. G. Lucas

BORN on Sept. 9, 1855, in the city of Spalato, Dalmatia. Austria, Antonio Francisco Luchich was the son of Francis Stephen Luchich, a prosperous shipbuilder and ship-owner of Lesina. His mother, Johanna Giovanizio, was known to the people of Trieste as a woman of unusual learning and piety. After receiving his high school training in Trieste, Antonio Luchich entered the Polytechnic Institute at Gratz in the year 1875, graduating two years later as an engineer. He then entered the Naval Academy of Fiume and Pola as a Midshipman, receiving his commission as a Lieutenant in 1878. In 1879, then 24, Antonio Luchich obtained a leave of absence from the Austrian Navy and came to Saginaw, Mich., to visit an uncle. He remained in this country and on May 4. 1885 at Norfolk, Va.. he became Anthony Francis Lucas. an American citizen.

Jan 1, 1945

FEB. 17-The past month found the average citizen backed off just a little more into his blind corner staring glassily at hydrogen bombs, unbalanced budgets, John L. Lewis, more inflation, a rising wave of strikes, the country&apos;s only active battleship on a mudbank, a famous scientist in gaol as a traitor, a favorite actress on a Roman holiday, and rising mountains of potatoes, butter and eggs begging for destruction. About the only bright spot has been industrial activity and employment, but even these are menaced by the coal shortage. Most industries have orders on hand or in prospect to warrant high operations for some time to come. The trend of the Reserve Board&apos;s production index is upward except as strikes may interfere. There has been heavy buying at the seasonal merchandise shows, particularly in furniture and house-hold goods. The demand for goods of this kind illustrates greater confidence in the Spring outlook than was generally felt a year ago. Further, the demand also reflects improved market positions due to curtailment of output and reduction of inventories in 1949 and sustained consumer buying power. It demonstrates the strong support that is given directly to many businesses, and indirectly to all, by the phenomenal construction activity that is now under way. The Commerce Department places the number of new dwelling units started in 1949 at the new all-time high of 1,019,000.

Jan 3, 1950

By Robert L. Hoss

The application of Muskat&apos;s differential equations for predicting the performance of a solution gas-drive reservoir to the Fullerton field indicates that a recovery may be expected of 14,030 bbl per acre under primary depletion, and 15,910 and I7,190 bbl per acre, respectively, under the two pressure-maintenance programs analyzed. In this analysis it is assumed that fluid properties are the same throughout the reservoir, that the core data used are typical of the Clear Fork limestone in the locality, and that injected gas is completely diffused through the pay zones. The economic study of the three recovery programs considered indicates that the one in which 60 pct of the produced gas is returned to the formation is the most profitable. Introduction The purpose of this paper is to consider the effect of pressure maintenance by gas injection on the ultimate recovery of oil from a solution gas-drive reservoir. This prediction of reservoir behavior is the result of calculations based on the equations presented by M. Muskat in the Journal of Applied Physics, March 1945. Reservoir The reservoir analyzed is the Fullerton field in Andrews County, West Texas. It is situated on a broad anticlinal structure with approximately 330 ft of closure, and extends approximately eight miles north and south and five miles east and west. The areal extent is taken as 16,642 acres. The producing horizon is the Lower Clear Fork limestone of Permian age, occurring at depths from 6650 to 7350 ft. It is divided into four zones. For the purposes of this study, the fluid characteristics in all zones are assumed to be the same. Therefore an equivalent zone is assumed of thickness equal to the sum of the thicknesses of the four zones, or an average of 216 ft. The reservoir contains 3,586,991 acre feet of producing limestone, with an initial volume of stock tank oil in place of 918,-403,100 bbl. The average connate water saturation is 24.0 pct. The permeability ranges from 6.7 md. to 12.6 md., and the porosity ranges from 7.7 pct to 11.4 pct, except for occasional cavernous streaks. Based on these values, the limestone may be considered intergranu1ar.l Production histories and material-balance studies have indicated that the driving mechanism is solution gas. Water levels have been established. Theory It is possible to express mathematically the change in residual oil saturation with pressure decline in a solution gas-drive reservoir as being equal to the change in the physical properties of the fluids present in the reservoir as this pressure decline occurs. Essentially these equations, in differential form as presented by M. Muskat,2 express quantitatively the instantaneous net effect

Jan 1, 1948

By Robert L. Hoss

The application of Muskat&apos;s differential equations for predicting the performance of a solution gas-drive reservoir to the Fullerton field indicates that a recovery may be expected of 14,030 bbl per acre under primary depletion, and 15,910 and I7,190 bbl per acre, respectively, under the two pressure-maintenance programs analyzed. In this analysis it is assumed that fluid properties are the same throughout the reservoir, that the core data used are typical of the Clear Fork limestone in the locality, and that injected gas is completely diffused through the pay zones. The economic study of the three recovery programs considered indicates that the one in which 60 pct of the produced gas is returned to the formation is the most profitable. Introduction The purpose of this paper is to consider the effect of pressure maintenance by gas injection on the ultimate recovery of oil from a solution gas-drive reservoir. This prediction of reservoir behavior is the result of calculations based on the equations presented by M. Muskat in the Journal of Applied Physics, March 1945. Reservoir The reservoir analyzed is the Fullerton field in Andrews County, West Texas. It is situated on a broad anticlinal structure with approximately 330 ft of closure, and extends approximately eight miles north and south and five miles east and west. The areal extent is taken as 16,642 acres. The producing horizon is the Lower Clear Fork limestone of Permian age, occurring at depths from 6650 to 7350 ft. It is divided into four zones. For the purposes of this study, the fluid characteristics in all zones are assumed to be the same. Therefore an equivalent zone is assumed of thickness equal to the sum of the thicknesses of the four zones, or an average of 216 ft. The reservoir contains 3,586,991 acre feet of producing limestone, with an initial volume of stock tank oil in place of 918,-403,100 bbl. The average connate water saturation is 24.0 pct. The permeability ranges from 6.7 md. to 12.6 md., and the porosity ranges from 7.7 pct to 11.4 pct, except for occasional cavernous streaks. Based on these values, the limestone may be considered intergranu1ar.l Production histories and material-balance studies have indicated that the driving mechanism is solution gas. Water levels have been established. Theory It is possible to express mathematically the change in residual oil saturation with pressure decline in a solution gas-drive reservoir as being equal to the change in the physical properties of the fluids present in the reservoir as this pressure decline occurs. Essentially these equations, in differential form as presented by M. Muskat,2 express quantitatively the instantaneous net effect

Jan 1, 1948