Search Documents

By Lawrence H. Van Vlack

The energy of the y-iron grain boundary was determined to be 850 ergs per cm2 at 1105°C. The a/a and the a/y boundaries possess somewhat less energy. The microstructures of several iron alloys are discussed in terms of the interfacial energy relationships. THE dependence of the shape of liquid interfaces upon their energies has been studied for some time.1"3 Recently, Smith' concluded that many of the microstructures observed in metals may be attributed to the energies of the interfaces between the grains and phases. While the energies of liquid surfaces have been measured by numerous different methods: only two attempts have been made to determine experimentally the energy of surfaces involving crystalline solids. Udin, Shaler, and Wulff8 used a procedure introduced by Berggren7 to measure the surface tension of solid copper. It consisted of determining the load required on a thin copper wire so that the surface tension was counteracted, and no net strain resulted. Bailey and Watkins8 sed a different technique and were able to determine both the surface tension of copper and the tension of the copper grain boundary. They measured the contact angle which liquid lead makes against a copper surface. They then calculated the above energies from the surface energy of liquid lead by using the Pb vs. Cu/CuY dihedral angle and the surface groove angle formed during thermal etching. They obtained a value of 1800 dynes per cm for the surface tension of clean copper and approximately 640 dynes per cm for the tension of copper grain boundaries. The former value was somewhat higher than Udin's value of 1500 dynes per cm. This paper includes a determination of the energy of the y-iron grain boundary. In addition, the micro-structural relationships of several other metallic and nonmetallic phases with iron were examined and an attempt was made to interpret the observed structures in terms of interfacial energy relationships. Theoretical Considerations In a three-phase material containing a solid and two liquids, there may be two solid/liquid interfaces, one liquid/liquid interface and one inter- granular interface. Liquid/liquid interfacial energies can be measured directly. Therefore, by determining the energy of such an interface and by measuring the required interfacial angles: the energies of the interfaces involving solids may be obtained.10 They may be shown schematically as in Fig. 1. The above procedure requires the following assumptions: 1—The interfacial energies are, in general, unaffected by boundary orientation, and 2— the shapes of the interfaces are unaltered between annealing and sectioning for microscopic examination. The first assumption is good to a first approximation as shown by Dunn and Lionetti11 except for a few critically orientated boundaries. Two conditions may alter the shape of a boundary upon cooling: 1—Precipitation of dissolved material upon one side of the interface, and 2—a change in volume during the transition from one phase modification to another. The former must be detected by microscopic observation. The latter may become appreciable in systems containing an interface between two liquids which solidify after annealing. However, possible movement of the two-liquid interface may be checked in the system diagrammed in Fig. 1 by measuring 8, for example, and comparing it with its value as calculated from the other interfacial angles by: tan8, C11 05 COS- o- + cos 8, cos- The choice of a suitable pair of liquids is limited by several factors. The relative values of the several

Jan 1, 1952

By E. V. Foran

The repressuring of oil-producing formations during the flush stage of production, although requiring primarily the same procedure as operations on formations where the gas pressure has been depleted, offers several advantages of major importance, the value of which has not heretofore been demonstrated. It is the purpose of this paper to present an account of some recent operations of this character and the economic effects on the properties where they were applied. The principal objective in all repressuring operations is to secure an effective diffusion of the input energy to all parts of the producing sand. If this can be accomplished, success is assured during the remainder of the life of the property; if not, it will be temporary only and will be followed by difficulties, .and the maximum possible recovery will not be obtained. During the past year in Texas, the Cook pool in Shackelford County, and the Turbeville pool in Archer County, while still in their flush stage of production, have been subjected to repressuring operations to observe their reaction to this process during the early stage of their productive periods. The repressuring operations carried on in each of these pools will be discussed separately in this paper in order to show peculiarities which were present in one pool but were not observed in the other. Turbeville Pool The Turbeville pool is in Archer County, about 30 rniles south of Wichita Falls. The productive sand varies in thickness from 10 to 30 ft., the average being about 16 ft. The depth of the sand varies from 1450 to 1530 ft. The developed productive area to date is approximately 200 acres, but the limits of the pool have not yet been proved. The sand varies considerably in different parts of the pool with respect to both porosity and permeability. The gravity of the oil varies from 39 to 41° A. P. I. There were some wells which flowed for a few days after completion but during 1927 all production was secured by pumping. The

Jan 1, 1928

By Donald P. Richards, John F. Abel

Geotechnical site investigation for new mine shafts can reduce the level of design uncertainty for shaft linings. The parameters which determine the lining strength required include rock strength and hydrologic properties, the in situ stress conditions, and the concrete strength. These parameters are applied to analytical methods of shaft lining design using the plastic and clastic assumptions of rock response to determine the required lining thickness to maintain the stability of the shaft excavation.

Jan 1, 1982

By B. R. Eichbaum, J. E. Murphy, J. A. Eisele

The US Bureau of Mines demonstrated ferric chloride leaching of galena concentrate on a continuous bench scale basis. Leaching was performed at 95°C (200°F) and with a contact time of 15 minutes. The ferric chloride leaching solution was continuously fed to a leaching tank at a constant rate for periods up to 45 hours. In each test, a constant redox potential was maintained in the slurry exiting the leaching tank by controlling the concentrate feed rate. In the 45 hour test, lead extraction exceeded 99.5%, and the lead chloride produced was 99.97% pure.

Jan 1, 1986

By N. P. Peterson

THE Castle Dome copper deposit is of the porphyry type and occurs in a body of quartz monzonite intruded into the pre-Cambrian formations and possibly into the lower part of Paleozoic limestones. The hypogene sulphide minerals include pyrite, chalcopyrite, and a little molybdenite, sphalerite, and galena. Pyrite and chalcopyrite are disseminated or occur in small closely spaced veins. The hypogene mineralization shows distinct zoning in the distribution of pyrite and chalcopyrite, so that the mineralized area can be subdivided into pyrite and chalcopyrite zones. Supergene enrichment, though not extensive, played an important part in the formation of the ore body, the chalcopyrite zone being the protore. Several thin, gently dipping, diabase sills occur in the mineralized area, and the copper content of the rock in and near these sills is substantially higher than average. The formation of the ore body was caused by the combined effects of three forces: I. Zoning of the hypogene mineralization, 2. Richer copper metallization associated with the diabase sills, and 3. Supergene enrichment.

Jan 1, 1947

By George W. Maynard

In the biographical notice of Thomas F. Witherbee, published in.Bulletin NO. 32, August, 1909 (p. xxv), it is said that "he is believed to have been the first manager in America to use the chemical laboratory for the purpose of controlling the regular running of the blast-furnace." Since the year is not given, I cannot decide as to Mr. Witherbee's priority; but the statement leads me to contribute a bit of history, showing an early departure from the " rule-of-thumb " blast-furnace work to the employment of a chemist. In the autumn of 1868 the department of mining and metallurgy was established at the Rensselaer Polytechnic Institute. In connection with the assay-department a laboratory was equipped for making general commercial analyses. In January, 1869, Alexander L. Holley, the manager and builder of the Bessemer plant at the Rensselaer Works of John A. Griswold & Co., the first plant erected in the United States under the Bessemer patents, began to send me samples

Jan 1, 1911

By B. G. Langston, R. D. MacDonald, F. M. Stephens

WITH the development of uranium ores that contain substantial amounts of acid-consuming compounds, the alkaline leach has become an attractive method for extraction. Considerable work has been done on both atmospheric and pressure-leaching with aqueous solutions of sodium carbonate and sodium bicarbonate as the lixiviants.1,2,3 For the treatment of uranium-bearing limestones and other high-lime (CaO) ores, the sodium carbonate leach has proven attractive because it avoids the high reagent consumption incurred by the reaction of sulfuric acid with lime. In addition, the corrosion problems with sodium carbonate are negligible as compared with those encountered in the acid-leach system. The sodium carbonate leach, however, does not yield as high an extraction of the uranium as the acid leach and is not attractive for economic reasons when treating ores that are high in sulfates or sulfides.

Jan 9, 1957

By Thomas D. West

A short time ago, I had occasion to cast iron plates 1 in. thick, direct from metal containing Si, 0.51; 8, 0.045; Mn, 0.75; and P, 0.094 per cent. Much to my astonishment, I found that there was no trouble in planing them; whereas, if cupolaimetal of like composition had been used,*the planing would have been a difficult operation. I have often noticed a greater fluidity or " life " in furnace-metal, as compared with the cupola-product. Iron can be seen flowing down the furnace-runners from 50 to 100 ft., and reaching the last pig-bed in satisfactory condition, while cupola-metal might have solidified before it had flowed so far. I have seen Bessemer iron, which, on account of its low phosphorus-content, does not have the " life " of ordinary foundry-iron, held in a 30-ton ladle for nearly an hour and a half; and after skimming off the coke-dust, it still had to be cooled off' considerably before being cast. As a general proposition, it is known that the lower sulphur-content and the frequently higher temperature of direct-metal, compared with the same iron remelted in the cupola, has much to do with its greater life; yet some problems connected with this phenomenon seem to call for further study. For instance, furnace-metal containing more than 1 per cent. of silicon holds carbon, which is separated later as "kish." This separation does not take place to any great degree while the metal is very hot; but during its gradual cooling, at times, the kish is given off in such large quantities as to cover the ground from 20 to 30 ft. around the ladle. In making castings of direct-metal, especially with a high content of silicon, the separation of kish becomes an annoyance. Perhaps this throwing out of the excess of carbon makes the life of the metal shorter, after it has been remelted in a

Jan 1, 1905

By Jerry G. Rose, Robert C. Howell

This paper addresses a process by which both the disposal and utilization of preparation plant coal refuse can be simultaneously accomplished with an attendant benefit of significantly increasing the percentage of extractable coal. A laboratory study is described in which coal refuse was successfully utilized as an aggregate in low cost concrete (coal-crete) mixes under simulated mine environments. Coal-crete specimens with compressive strengths of 14 000 kPa (2000 psi) were consistently produced. A construction sequence and mining plans are offered for placing the low-cost coal-crete pillars in accessible areas in room and-pillar mines so that a substantial portion of the remaining coal pillars could be extracted. The method could be applicable in areas where mining procedures do not permit pillar extraction became of possible surface subsidence, roof problems, or other conditions. Possible structural difficulties with the coal- crete pillar support system are discussed. Using a discounted cash flow analysis, the economic feasibility of mining with the coal-crete pillar system is investigated. The cost of the system is compared to the cost of a mining system which would have less coal recovery. The analysis indicates that although at higher coal selling prices the coal-crete mining system may yield an acceptable rate of return, the alternative of leaving the coal pillars is more attractive at the present time.

Jan 3, 1979

By George E. Kruger, William F. Butler

The less developed nations maintaining a free enterprise economy (to which this chapter is addressed) have real and substantial opportunities to lay a foundation for general economic progress by using their mineral resources. Most of these nations have mineral resources which could be developed. By seizing these opportunities, nations seeking rapid economic development can secure a source of foreign exchange earnings to finance the imports needed for growth and, at the same time, increase the technical knowledge and well-being of an important part of their population. History clearly shows the manner in which most of the currently industrialized nations have used mineral resources to support their development. Indeed, few nations have managed to achieve a high level of income without a firm base of mineral resource development. The main exceptions appear to be the Netherlands, Switzerland, Denmark, and New Zealand, and the last two have based their prosperity on a highly efficient agriculture. Economic growth in the United States, the United Kingdom, Canada, France, Germany, and Russia was importantly based on the use of indigenous mineral resources. Despite this record of accomplishment through mineral development, many of the currently less developed nations are not taking advantage of the opportunities available in the mineral field. Restrictive laws or practices in many such nations operate effectively to prevent development of mineral resources. This failure to grasp real opportunities for development is based on a series of arguments that the mineral field offers few substantial and attainable advantages. Among these, the following propositions appear the most important:

Jan 1, 1964

By James W. Baxter

Underground mining of limestone is becoming increasingly practicable in Illinois. Most quarries are near rivers on the western and southern borders where competition for land use is intensive. Increasing demands for stone can be met by expanded mining with access by adits in existing quarries and by inclines and shafts at downdip sites. Geologic, hydrologic, and engineering conditions indicate that deep mines in the Ste. Genevieve, Salem, Ullin, and basal Burlington limestones of Mississippian age and in the Moredock member of the Dunleith formation of Ordovician age are particularly feasible, but development will require prudent exploration and planning to ensure that the product will be of good quality.

Jan 1, 1981

By J. Washburn

Two simple types of dislocation distribution were introduced into zinc crystal specimens and the effect of each on the stress-strain curve was investigated. Quantitative results were obtained for simple edge dislocation arrays and for an array of screw dislocations lying in the slip plane. A CCORDING to present knowledge, the disloca-tions present in large annealed metal crystals can be divided into two somewhat arbitrary groups: 1—single dislocation lines distributed more or less at random or forming elements of a three-dimensional network in which the distance between adjacent dislocations is of the order of 10 2 to lo-' cm and 2— widely separated planar arrays of edge dislocations forming dislocation walls or small angle boundaries within which adjacent dislocation lines are spaced at much smaller distances (lo-' to 10- hm). The former can be considered as a dislocation interpretation of the mosaic crystal proposed by Darwin and Ewaldl, ' 40 years ago to account for anomalously high integrated intensities of X-ray diffraction maxima. Small angle boundaries, although now known to be present in most single crystals used for mechanical testing, were not generally recognized by the early workers. This was partly due to the fact that only recently have improved X-ray and metal-lographic techniques been available for checking the macroscopic perfection of crystals."" It has long been known that changes in growth conditions and in annealing procedure, which might logically be expected to cause variations in the structural details of both the dislocation network and of dislocation boundaries, produce marked variations in some mechanical properties such as yield strength." However, no quantitative experimental correlations between changes in dislocation distribution and changes in mechanical properties have yet been made. Such a correlation has been difficult to obtain because, even when great care is exercised to keep the histories of a number of single crystal specimens identical, it usually has not been possible to avoid considerable variation in macroscopic per- fection.' The number and orientation of dislocation boundaries vary from specimen to specimen. This has probably been an important contributing factor to the large scatter in the results of most mechanical measurements on pure single crystals. Some recent experiments"% ith single crystals of zinc have shown that the presence of dislocation boundaries in a specimen can increase its resistance to deformation by slip. With polycrystalline aluminum and nickel, there is also evidence that dislocation boundaries within the individual grains of the aggregate can increase the resistance of the material to plastic deformation, either as measured by tension tests at room temperature or by creep tests at higher temperatures.'" " Although the foregoing observations seem to have established the fact that substructure can have a strengthening effect, the test conditions were too complex to give much information concerning the mechanism. In the foregoing cases, a network of intersecting boundaries having various orientations and boundary angles were present. Before their apparent strengthening effect can be understood, it will be necessary to isolate and study separately the effect of a number of variables: 1—boundary angle, 2—boundary orientation with respect to the active slip direction, 3—number of boundaries, 4—intersections of boundaries, 5—detailed structure of the boundaries, and 6—interaction of impurity atoms with dislocations in boundaries. The object of the present work was to study the effect of dislocation boundaries on flow stress under the following simple experimental conditions: 1— substantially pure shear deformation and 2—boundaries of controlled angle, orientation, and number. In this way, it might be possible to distinguish the important variables from the relatively unimportant ones. Experimental Procedure Stress-strain curves of hexagonal metals are generally nearly linear even out to very large strains."

Jan 1, 1956

By B. Etkin, A. A. Haasz

The Infrasizer Mk III, developed at the University of Toronto, is capable of sizing particles of a few pm to hundreds of pm according to particle terminal velocity, which is a function of particle density, size and shape. The factors limiting the performance of the Infrasizer Mk III have been presented and analyzed. It has been established theoretically and experimentally that the device has excellent potential as a laboratory instrument. The principle is applicable to a continuous production classifier, a prototype of which is now under development.

Jan 1, 1980

By Richard R. Parizek, E. Scott Blair

Numerical modeling of ground water flow systems can be used to help analyze many practical problems encountered in the mining industry. Numerical models can be used to predict ground-water seepage rates into surface mines, shafts, and other large excavations; to predict water-level changes under adjacent properties; and to predict the effectiveness of various deep-well dewatering schemes. As with any model, the results from a numerical model are limited by the quality and quantity of data, and by the restrictions of any simplifying assumptions. A case study is presented that shows how a numerical model was used for engineering purposes to help analyze the hydrologic impact of a proposed open-pit mine by Predicting changes in the dewatering rate caused by the lateral growth and deepening of the mine and by predicting the effectiveness of various deep-well dewatering schemes.

Jan 1, 1982

ONE of the fundamental reasons for the extreme rapidity with which the Porphyries developed after the trail had been blazed at Bingham was the amenability of the deposits to prospecting and proving of the ore either by churn-drilling or by diamond-drilling. At Ray churn-drill data formed the principal basis for early calculations of ore reserves; and in 1913, Inspiration floated its first bond issue for $6,000,000 on the strength of the estimate of 45,000,000 tons of sulphide ore assaying just over 3 per cent copper. The money was obtained in spite of the fact that no one ever had actually laid eyes on more than a minute fraction of that ore. The customary method of developing a copper deposit before the Porphyry era had been to sink shafts or drive adits and then to follow and expose the veins or lodes with horizontal and vertical underground workings-drifts, crosscuts, raises, and winzes. The excavated material sometimes was sampled in bulk; but always the walls of the openings would be channeled at intervals to obtain small samples representative of the ore left in place. This process was known as "blocking out" ore. It was costly and it required a great deal of time to prove the existence of immense tonnages. The early development at Utah was done in this way; likewise, at Miami. This fact helps to explain why only 3,000,000 tons of ore was reported as being developed when J. Parke Channing wrote the report on which the original Miami financing was based in March, 1908. Fortunately, his 3,000,000 tons averaged 3'per cent copper. At Ray, Seeley W. Mudd estimated 3,000,000 tons of ore in June, 1908, developed principally by underground working; but by the end of 1909, Henry Krumb was able to report 50,000,000 tons as the fruit of a little more than a year of churn-drilling.

Jan 1, 1933

By David A. Summers, John Corwine, Li-King Chen

The results from fracturing plexiglas beams are combined in eight existing equations to determine the surface energy of the material. The reliability of each equation is tested, and the equation in use to determine fracture toughness is found to be the most exact. This equation is then used in determination of the surface energy of Barre Granite.

Jan 1, 1971

JAMES DOUGLAS Dr. James Douglas, twice President of the American Institute of Mining Engineers, and one of its principal benefactors, died in New York on June 25, 1918, at the age of 81 years. After a life of extraordinary activity, failure of his health compelled him to retire about 2 or 3 years ago, and in view of his advanced years his death was not unexpected. His funeral was held at the Church of the Mediator, on June 26, and was attended by representatives of the American Institute of Mining Engineers and of the Canadian Mining Institute. His body was then taken to Quebec for burial in the family plot. An extended notice of Dr. Douglas, prepared by Dr. R. W. Raymond, will be presented in the September issue of the Bulletin. LEWIS NEWTON BAILEY Lewis Newton Bailey died of pneumonia at Camp Merritt, N. J., April 30, 1918, at. the age of 34 years. He was Master Engineer, .Senior Grade, in the Fourth Regiment, U. S. Engineers; and although he was offered a commission as First Lieutenant shortly after enlisting, he preferred not to accept it until he had reached France. By those who knew him well, this lack of eagerness for promotion will be recognized as consistent with his whole character.

Jan 8, 1918

By Nicholas J. Grant, Gordon D. Gemmell

CREEP rupture characteristics of high purity Al-Mg solid solution alloys were studied by Mul-lendore and Grant' to investigate solid solution strengthening of pure aluminum and the accompany- ing effects on deformation and fracture characteristics. This paper presents the results of an extension of that work to A1-Cu and Al-Zn alloys to permit a comparison of the relative effects of the three solute elements on the high temperature strength and on the deformation and fracture characteristics. Experimental Procedure A total of nine alloys was studied. They were all made of ultra high purity aluminum alloyed with high purity copper, zinc and magnesium. The corn-

Jan 1, 1958

By Benjamin B. Lawrence

The lease-system is the gradual result of the development of our larger producing mines throughout the State of Colorado. The operation of a mine, or group of mines, by corporations has been attended, in many cases, by disaster, owing to the difficulty of securing a fair day's work from the men employed in the mine, and the loss entailed by careless mining and sorting of high-grade ores, or by lax or inefficient management on the part of superintendents and foremen. Given, therefore, a mine that has been practically abandoned by its owner, for the reasons given, but still possessing merit, the lessee appears on the ground and secures a lease for a year, or term of years, from the owner, upon the payment of a royalty upon the gross smelter- or mill-returns of the ore which he mines. In this way many of our abandoned mines have been re-opened by the miner, who, with two or more associates, has been enabled, by careful attention, to obtain profitable results.

Jan 1, 1893

By W. D. Klopp, R. I. Jaffee, H. R. Ogden, D. J. Maykuth

The purification of commercial-purity tantalum powder by vacuum sintering in the temperature range 2600° to 2860°C has been investigated. Mixtures of tantalum oxide and tantalum carbide were sintered at 1800° and 2200°C. Tantalum bars containing 1 pct additions of oxygen, nitrogen, and carbon. were sintered in the range 1800° to 2600°C. Anulyses were conducted on the sititeyed mixtures to determine the extent of removal of oxygen, nitrogen, and carbon at each sintering condition. The mechanism for remova1 of each impurity, and the conditions necessary for preparing ductile tantalum by vacuum sintering are discussed. INTEREST in the refractory metals has been stimulated in recent years by the need for structural materials capable of operating at temperatures of 1100°C and higher. These metals include columbium (niobium) (mp 2468°C), molybdenum (mp 2620°C), tantalum (mp 2996°C), rhenium (mp 3160°C), and tung- sten (mp 3415°C). In addition to its high melting point, tantalum possesses the advantages of forming a solid, nonvolatile oxide at temperatures of interest and of being ductile and easy to fabricate. The classic method of consolidating tantalum from powder refined from the ores is by vacuum sintering at temperatures on the order of 2600°C. This sintering treatment both densifies the compacted powder bars and purifies the metal by causing impurities to boil out. The present work was undertaken to provide more quantative data on the relationship between sintering conditions and purity and to determine the mechanisms of impurity removal.

Jan 1, 1961