Search Documents

By E. Swartzman, G. C. Behnke

THE free-swelling index, a numerical value for the free-swelling properties of coal, is being used to an increasing extent in specifying coal for burning in various types of equipment. The empirical standard ASTM method for determining this index uses, as a source of heat, a gas burner which requires frequent calibration because gas pressures are not constant, relatively small changes in gas pressure resulting in rather wide variations in the temperature attained in a crucible and thus in the resultant size of the coke button. Furthermore, the quartz crucibles specified for the test are not standard equipment, and relatively small variations in dimension and wall thickness from those specified often result in rather wide variations in the resultant size of the button. A method of analysis to be satisfactory not only for a scientific laboratory but also for use in industrial control laboratories under varying conditions should employ equipment which is rugged, easily calibrated, and readily replaceable by standard materials. Gas is not universally available as is electricity, and it is generally easier to calibrate and control a simple electric furnace or heater than a gas burner, the voltage not usually fluctuating to the degree that gas pressure does. Quartz crucibles are fragile, and the size specified in the test is not normally used for any other purpose in the laboratory. Although more expensive, the 15-cc platinum crucible, available in all laboratories where volatile matter in coal is determined by the standard ASTM method, is sturdy and standard and easily replaced. Because of these considerations, a modification of the standard method has been developed which employs a standard laboratory 350-w cone heater and standard 15-cc platinum crucibles. The results of numerous tests conducted with such apparatus show conclusively that the free-swelling index values as judged by the buttons produced with this equipment are exactly the same as those obtained by the standard gas burner method. Thus it is suggested that this electric cone heater method employing standard 15-cc platinum crucibles be considered as an alternative to the ASTM method, Designation: D720-46. The free-swelling index of coal is determined by means of the ASTM method, D720-46. This method, which is an adaptation of the crucible swelling test for coal of the British Standards Institution, consists of heating 1 g of coal in a special covered quartz crucible in a regulated gas flame for a period of not less than 2.5 min in which time the temperature of the inner surface of the bottom of the crucible reaches a temperature of 82025°C. The residual coke button is then compared in size and shape with a series of standard profiles shown in Fig. 1 and designated by number from 1 to 9 in increasing order of size. As the method is empirical, it requires rigid standardization of the apparatus and repeated calibration of the gas burner. The dimensions of the low form quartz crucible recommended must be rigidly adhered to as small variations in diameter or wall thickness result in variations in the rate of heat transmission and thus in the resultant size and shape of the coke button. The gas burner must be calibrated almost every time a new set of determina-

Jan 1, 1952

INTRODUCTION The first installation of large, commercial, high gradient-high field cannister and matrix magnetic separators for removal of impurities from kaolin was made in 1973 (1). Since then the technology and equipment have been widely adopted for clay processing with about 12 units in commercial use. These new separators have filled a need, caught the imagination of many and become a technology worth fighting for. A fight has occurred, and a resolution on royalties for kaolin processing, at least, has been achieved. LIMITATIONS TO APPLICATIONS OF MAGNETIC SEPARATORS Other than the use of these magnets on kaolin clay, no other application has yet achieved widespread adoption. Dr. Iannicelli blames inertia, and1 would agree that it is a factor. There are other reasons too, and if they are examined, they may isolate problems that R&D can significantly assist in solving. I'd like to break the problems into two areas. Machine limitations - the mineral properties are there but performance is insufficient or uneconomic. Separation limitations - the mineral properties aren’t there, but the magnetic separation would perform well if the properties were there (size is right; concentration is right, etc).

Jan 1, 1979

By E. S. Bardwell, R. J. Lapee

Twenty years ago, W. T. Burns, in his paper presented at the Butte Meeting of the Institute,' discussed the general scheme then in use in the electrolytic copper refinery of the Anaconda Copper Mining Co. at Great Falls, Mont., for removing impurities from tank-room electrolyte and controlling its acid content. Since then marked changes have taken place in copper-refinery practice at Great Falls. The electrolytic copper refinery in use in 1913 has been replaced by a new and entirely modern plant capable of producing up to 27,000,000 Ib. of cathode copper per month. With the building of the new plant in 1916, the treatment of converter anodes was discontinued. At first the substitution of refined anodes for converter anodes resulted in a decrease in the impurity content of the anodes, but as time went on, changes in metallurgical practices at the smelter resulted in substantial increases in the impurity content of the anodes. The leaching of the silver slime to remove copper before shipment to Raritan for treatment further added to the purification problem. The fact that the scheme of purifying electrolyte which Mr. Burns described in his paper has proved adequate for our needs under a wide variation of conditions speaks well for its essential soundness. Method of Purification Briefly, the method adopted for purifying tank-room electrolyte at Great Falls has been as follows: Each day a certain volume of tank-room electrolyte is run off and sent to the purification plant, where it is boiled down to approximately 46' 136. The concentrated electrolyte is then sent to crystallizing tanks where the bulk of the copper is crystallized out as copper sulfate. The mother liquor is then passed through insoluble anode tanks to remove the last of the copper and most of the arsenic and antimony. It is then either returned to the tank room direct or boiled down to 55' Bé, the iron and nickel salts crystallized out and the mother liquor returned to the tank-room circuit as restored acid. Prior to 1930 all of the evaporating was done in lead-lined tanks 13 ft. in diameter by 4.5 ft. deep, provided with lead heating coils through which steam at 30 lb. gage pressure was circulated.

Jan 1, 1934

By R. H. Frazier, C. H. Lorig, F. W. Boulger

This investigation establishes the effect of ferrite grain size resulting from various heat treatments on the transition temperature of a semikilled steel plate. Different austenitizing temperatures and various cooling rates were used. The ductile-brittle transition temperatures were determined by the Navy tear test and the keyhole Charpy test. THE data presented in this paper deal with quality characteristics of ship-plate material which were investigated in a research project sponsored at Battelle by the Bureau of Ships, Dept. of the Navy. Specifically, the object of this investigation was to establish the effect of ferritic grain size (resulting from various heat treatments) on the so-called transition temperature of ship-plate steel. Transition temperature is not a fixed property of steel. It is derived from a series of static or dynamic tests made at various temperatures and is qualified by specifying the type of test employed as well as the testing criteria. Because in earlier investigations of ship-plate quality1,2 the so-called Navy tear test and standard notched-bar tests (keyhole Charpy) proved to be useful in interpreting instances of brittle behavior of ship plate in service, these tests were used in the investigation reported in this paper. By definition,' in the Navy tear tests the highest temperature at which one or more of four specimens breaks with a brittle fracture (that is, when less than 50 pct of the fracture area has a dull fibrous texture) is termed "transition" temperature. In the Charpy tests, the 12 ft-lb level of energy absorption was used as a criterion indicating the "transition" temperature, although other levels of energy absorption were also used for comparison. Earlier work" on ship-plate steels indicated that the temperature at which ship plate is finished has a very significant effect on its notched-bar properties. Plates rolled in the laboratory, where the finishing temperature can be carefully controlled, showed a 16°F decrease in tear test transition temperature when the finishing temperature was lowered 200°F (from X" to Y°F). The same plates showed a drop of 10°F in the keyhole Charpy transition temperature from the same decrease in finishing temperature. Commercially finished plates' exhibit a similar trend. When the ferrite grain size of the hot-rolled laboratory plates was determined, a close relationship was found between the ferrite grain size and the notched-bar transition temperature." " he indicated relationship between grain size and transition temperature was in agreement with the findings on low carbon steels of Hodge, Manning, and Reichhold' despite the differences in composition of the steels. The cooling rate after rolling varies from one steel plant to another. This variation changes the micro-structure" and appears very likely to affect the notched-bar properties of the steel plates. In the investigation summarized in the present paper, heat treatments simulating finishing practices in the hot rolling of ship plate were used in order to vary the ferritic grain size. It is believed that the indicated relationship between grain size and transition temperatures of the ship-plate material will prove useful in estimating the effect of rolling temperature and of cooling rates from rolling temperatures on the notched-bar properties of semikilled steel plate. Material The semikilled steel plate used in this investigation was a ¾ in. hot-rolled plate from an open hearth heat. Other plates from this heat have been used on many other studies performed for the Ship Structure Committee," "," and the heat has been identified as project steel "A". The chemical composition of the plate1 was 0.25 pct C, 0.49 pct Mn, 0.011 pct P, 0.045 pct S, 0.04 pct Si, and 0.004 pct N.

Jan 1, 1956

By T. F. Adams, D. P. Morse

Tunneling is primarily an excavating cycle consisting of a sequence of operations: drilling, shooting, ventilating, mucking, and erecting supports, if necessary. However, the type and condition of the ground that is being worked, as well as the size and shape of the tunnel, determine the rate of advance. In addition developments in drilling, ventilation, mucking, and haulage equipment have contributed to faster tunneling. Geology: This discussion will be limited primarily to rock tunnels or those which require the use of explosives, and the cost and hazards depend primarily on the condition of the rock which may be broken, decomposed, and contain water with gas. Advance geological study is an important part of any tunnel work and helps to minimize serious miscalculations. The geology itself, at best, is a matter of experience and prediction and it is not so much a matter of the types of rock the tunnel may go through, but a knowledge of the class and intensity of the rock defects that may be encountered.

Jan 4, 1958

By FREDERICK W. BRADLEY

MINING methods are evolved rather than devised; and the process is slow. The advance in no particular year is phenomenal, but progress is un- questionably being made constantly in several directions: (a) better adaptation to given conditions of various "systems" of mining; (b) better utilization of mechanical equipment ; (c) improvement in working conditions so as to promote the health, safety and efficiency of the workers. During the year 1930 operations were commenced at a number of important new mines. Methods adopted are not new, except in minor detail, but the fitting of methods to conditions is interesting, because, as the engineers presumably started from scratch, they have selected the methods that experience under similar conditions has indicated as being the best.

Jan 1, 1931

By L. C. Morganroth

Magnesite both Massive and Crystalline MAGNESITES are. of two general classes-massive and crystalline. Massive magnesite occurs in serpentine, being formed by the breaking down or decay of serpentine-making minerals or rocks as olivine, etc. (All the magnesia contained by the olivine is not liberated, as a portion goes to make up the serpentine; the breaking up of this serpentine later forms more magnesite.) Serpentine in various stages of transformation is found in the vicinity of magnesite deposits. Massive magnesite is very widely distributed. It is found in Greece, . California, Africa, India, Australia, Mexico, South America, and deposits of varying sizes occur in several of the European countries. Those on the Island of Euboea, Greece, are probable the most important deposits of this character of magnesite. They have been worked for a number of years, the principal quarries or mines being 3 miles in the interior from the village of St. George. (St. George is on the west coast of the island, between the towns of Limni and Khalkis.) (Figs. 1 and 2). -The magnesite occurs in veins or lenses in serpentine. Some of these lenses are very large; one worked several years ago was approximately, 50 ft. in thickness, 75 to 100 ft. high and 300 ft. or more in length. The magnesite is pure white and makes a very prominent feature of the landscape. While massive magnesite is widely scattered over the world, many of the deposits are in veins too thin to work. The usual mode of occurrence is in the form of stock work, the deposits in Venezuela, Mexico, and many of those in California, being of this form. The veins vary in thickness from the thinness of paper up to several inches, running in all directions, occasionally leading to a mass or nucleus of some,size. The spaces between the veins are filled with a disintegrated serpentine in the form of sand. Several of the deposits in California would probably be workable, if they were more favorably situated with reference to transportation, but by far the majority of the deposits are too poor to work. At one deposit,

Jan 9, 1914

By Frederick A. Mumpton

For more than 200 years zeolites have been familiar minerals to geologists and mining engineers as minor, but ubiquitous constituents in vugs and fractures of most basalt and traprock formations. More than 35 different species have been recognized including several, such as chabazite, erionite, mordenite, and faujasite, whose adsorption properties rival those of many synthetic molecular sieves. Igneous occurrences of this type have never been mined on a commercial scale; they are generally small and low grade, and they commonly contain as many as four zeolite minerals, along with small quantities of calcite, quartz, and other silicate minerals. Their economic beneficiation to monomineralic zeolite products has also not been achieved and, for the most part, industrial applications of zeolites have relied primarily on synthetic molecular sieves that were crystallized from hydrous aluminosilicate gels. During the middle 1950s, when Union Carbide Corp. and other groups were developing processes and markets for their fledgling synthetic zeolite businesses, natural zeolites

Jan 1, 1983

By Oscar Weiss

STILFONTEIN and surrounding areas gave negative results in all prospecting attempts since about 1904 when Goerz and Co., a forerunner of Union Corporation Ltd., first drilled in the region and on the farm Stilfontein. Subsequent efforts by African and European Investments Co. and Anglo American Corp. from 1934-37 were completely unsuccessful. Holes drilled by these companies on the farms Rietfontein, Hessie, and Palmietfontein were stopped in the Lower Witwatersrand system without finding payable reefs.

Jan 10, 1951

By J. C. Sullivan, W. A. Knoll

The sinking of a new shaft at the Newport mine, Ironwood, Mich., was started in May 1931 and completed on Aug. 3, 1932. During this period, 2665 ft. of shaft in granite was completed, at an average advance of 6 ft. per 24 hr. In Novernber of 1930, experimental work was conducted on 65 ft. of shaft through 22 ft. of overburden where ledge was encountered, and this work convinced the operators that all drilling could be done with vertical holes with the blasting relief to a 4½-in. hole drilled vertically in the center of the cut. The reason for not adopting the conventional V-cut was to get away from damaging the shaft steel. The blasting in a V-cut naturally tends to throw the broken material upward, but with the cut as adopted the relief was in a horizontal direction to a large extent. The scheme of mucking employed made it necessary to keep the steel shaft sets within 50 ft. of the bottom at all times. This could not be done without serious damage with a V-cut when blasting in granite. The cut as drilled also broke 10.83 ft. per round of drilling, which was considerably more than the experience with a V-cut in the same material. The extended cut reduced proportionately the delays for charging, blowing smoke and handling drilling equipment in the shaft. Another advantage was the ease in drilling vertical over inclined holes, and the preservation of the proper spacing of the drill holes at the bottom of the cut. Drilling Air was carried down the shaft in an 8-in. flanged pipe line at a pressure ranging from 95 to 100 Ib. This line was extended to within 100 ft. of the bottom, where a valve and a 4 by 4 by 6-ft. tee was connected to it. To each side of the tee was connected a nipple and elbow, the resulting span of the two elbows being about 4 ft. Lengths of short 3-in. hoses

Jan 1, 1940

By J. C. Sullivan, W. A. Knoll

The sinking of a new shaft at the Newport mine, Ironwood, Mich., was started in May 1931 and completed on Aug. 3, 1932. During this period, 2665 ft. of shaft in granite was completed, at an average advance of 6 ft. per 24 hr. In Novernber of 1930, experimental work was conducted on 65 ft. of shaft through 22 ft. of overburden where ledge was encountered, and this work convinced the operators that all drilling could be done with vertical holes with the blasting relief to a 4½-in. hole drilled vertically in the center of the cut. The reason for not adopting the conventional V-cut was to get away from damaging the shaft steel. The blasting in a V-cut naturally tends to throw the broken material upward, but with the cut as adopted the relief was in a horizontal direction to a large extent. The scheme of mucking employed made it necessary to keep the steel shaft sets within 50 ft. of the bottom at all times. This could not be done without serious damage with a V-cut when blasting in granite. The cut as drilled also broke 10.83 ft. per round of drilling, which was considerably more than the experience with a V-cut in the same material. The extended cut reduced proportionately the delays for charging, blowing smoke and handling drilling equipment in the shaft. Another advantage was the ease in drilling vertical over inclined holes, and the preservation of the proper spacing of the drill holes at the bottom of the cut. Drilling Air was carried down the shaft in an 8-in. flanged pipe line at a pressure ranging from 95 to 100 Ib. This line was extended to within 100 ft. of the bottom, where a valve and a 4 by 4 by 6-ft. tee was connected to it. To each side of the tee was connected a nipple and elbow, the resulting span of the two elbows being about 4 ft. Lengths of short 3-in. hoses

Jan 1, 1940

By R. H. B. Jones

This paper reviews pertinent geology of the Biwabik iron formation, Mesabi Range, Minnesota. This iron formation is divisible into four members. Each member is distinctive and contains marker horizons, which are recog nizable throughout all phases of alteration from lean, fresh rock to high-grade iron ore. Some beds have a larger magnetite content than others. During the process of ore genesis, which is essentially an oxidation process, the magnetite content is lowered. Alteration from iron formation to ore includes both oxidation of iron minerals and silica removal by leaching and these distinct processes progress at variable rates for different locations and structures. Magnetic intensities, of each horizon of the iron formation are dependent chiefly upon its preoxidation magnetite content, upon the subsequent degree of oxidation, upon the character of the enclosing rocks, and on the extent of fracturing, folding, or faulting. The results of a number of magnetic surveys are described and are correlated with results of drill-hole and mine exploration and developmerit. The magnetic anomalies obtained are discussed in relation to phases of formation of ore within the iron formation. General Information One hundred years ago a party of surveyors, applying the principles of geophysical prospecting, discovered iron ore in the state of Michigan in the Lake Superior district. This event was officially reported as follows:' On Sept. 19 (1844) while running the east line of Town 47 North, Range 27 West, they observed by means of the solar compass remarkable variations in the direction of the needle, amounting to 87" from the normal. Ascribing this phenomenon to iron ore, they sought and found it in ledges or outcrops at several points. The solar compass referred to was invented by William A. Burt, deputy surveyor in charge of this party.2 It is used for determining the true meridian by an observation on the sun. Eight years later, on July 7, 1852, the first iron 're, consisting of 6 bbl. of Ore, was shipped from Marquette, Michigan. It was another 40 years before the first or> shipment left the Mesabi Range in Minnesota, in October 1892. It totaled 4245 tons. Fifty years later, 90 years after the original shipment, during 1942 the Lake Superior district shipped 93,495,392 gross tons of iron ore. Production came from Minnesota, Michigan, Wisconsin, and Ontario, Canada. Throughout the 90-Year period it was known that magnetic properties of most of the ore bodies, and of the iron formations in which they occur, affected the compass. This phenomenon, later to be made use of to outline areas of ground favorable for exploration, was at first a

Jan 1, 1949

By R. H. B. Jones

This paper reviews pertinent geology of the Biwabik iron formation, Mesabi Range, Minnesota. This iron formation is divisible into four members. Each member is distinctive and contains marker horizons, which are recog nizable throughout all phases of alteration from lean, fresh rock to high-grade iron ore. Some beds have a larger magnetite content than others. During the process of ore genesis, which is essentially an oxidation process, the magnetite content is lowered. Alteration from iron formation to ore includes both oxidation of iron minerals and silica removal by leaching and these distinct processes progress at variable rates for different locations and structures. Magnetic intensities, of each horizon of the iron formation are dependent chiefly upon its preoxidation magnetite content, upon the subsequent degree of oxidation, upon the character of the enclosing rocks, and on the extent of fracturing, folding, or faulting. The results of a number of magnetic surveys are described and are correlated with results of drill-hole and mine exploration and developmerit. The magnetic anomalies obtained are discussed in relation to phases of formation of ore within the iron formation. General Information One hundred years ago a party of surveyors, applying the principles of geophysical prospecting, discovered iron ore in the state of Michigan in the Lake Superior district. This event was officially reported as follows:' On Sept. 19 (1844) while running the east line of Town 47 North, Range 27 West, they observed by means of the solar compass remarkable variations in the direction of the needle, amounting to 87" from the normal. Ascribing this phenomenon to iron ore, they sought and found it in ledges or outcrops at several points. The solar compass referred to was invented by William A. Burt, deputy surveyor in charge of this party.2 It is used for determining the true meridian by an observation on the sun. Eight years later, on July 7, 1852, the first iron 're, consisting of 6 bbl. of Ore, was shipped from Marquette, Michigan. It was another 40 years before the first or> shipment left the Mesabi Range in Minnesota, in October 1892. It totaled 4245 tons. Fifty years later, 90 years after the original shipment, during 1942 the Lake Superior district shipped 93,495,392 gross tons of iron ore. Production came from Minnesota, Michigan, Wisconsin, and Ontario, Canada. Throughout the 90-Year period it was known that magnetic properties of most of the ore bodies, and of the iron formations in which they occur, affected the compass. This phenomenon, later to be made use of to outline areas of ground favorable for exploration, was at first a

Jan 1, 1949

By Frederick C. Langenberg

A method is presented for computing the solubility of nitrogen in molten alloy steels. Examples are given to illustrate the procedure, and comparisons are made between predicted and measured nitrogen solubilities. THERE is an increasing use of nitrogen as a major alloying element in steels, or as a partial substitute for other alloying elements. Nitrogen is a potent austenite stabilizer, and Cr-Mn-low Ni-N steels, or even Cr-Mn-N steels, are being considered

Jan 1, 1957

By H. C. Lukens, E. V. Potter

The volume of hydrogen released from electrolytic manganese at various temperatures and pressures was determined in a previous investigation1 as part of a study to determine the most practical procedure for removing the hydrogen from electrolytic manganese metal. No attempt was made to determine the absolute volume of gas in the metal at any temperature and pressure; the volume of gas released showed only the variation in solubility with temperature and pressure. The results were very similar to those obtained by Sieverts and Moritz.² Both sets of data show a minimum solubility between 500' and 700°C., but they differ in certain respects; on cooling from 500°C., our results showed an increase in solubility of about 7 C.C. as compared with an increase of 34 C.C. per 100 grams shown by Sieverts. Furthermore, the transition temperatures, as indicated by sharp breaks in the solubility curves, did not agree well with Sieverts' data. This information was of secondary importance in the earlier investigations, and the solubility at low temperatures and the transition temperatures were subject to considerable error. Therefore, a subsequent investigation, reported in this paper, was made to measure the absolute solubility at temperatures from room temperature through the melting point and make more accurate observations of the transition temperatures. Apparatus and Method The apparatus and method were essentially the same as those described in the previous work,' as shown in Fig. I. At high temperatures, the small tube containing the thermocouple in the sample container A frequently broke off, so for some of this work the thermocouple was placed outside the sample container and protected by a quartz tube of about the same wall thickness as the sample container. No significant difference was found in the transition temperatures obtained in the two ways. The automatic temperature controller was used in these tests in the regions where there was little change in solubility with temperature. In the neighborhood of the transition points a continuously variable autotransformer was used instead of the automatic controller, and the power input to the furnace was adjusted so that the temperature increased or decreased at a very slow, uniform rate through the transition range. This procedure was followed because the temperature oscillations produced by the controller were too great compared with the transition range, and the transi- . tion points determined under such conditions were less accurate. Absolute Solubility Procedure ad Results The absolute solubility of hydrogen in manganese could be determined most

Jan 1, 1947

By E. V. Potter, H. C. Lukens

The volume of hydrogen released from electrolytic manganese at various temperatures and pressures was determined in a previous investigation1 as part of a study to determine the most practical procedure for removing the hydrogen from electrolytic manganese metal. No attempt was made to determine the absolute volume of gas in the metal at any temperature and pressure; the volume of gas released showed only the variation in solubility with temperature and pressure. The results were very similar to those obtained by Sieverts and Moritz.² Both sets of data show a minimum solubility between 500' and 700°C., but they differ in certain respects; on cooling from 500°C., our results showed an increase in solubility of about 7 C.C. as compared with an increase of 34 C.C. per 100 grams shown by Sieverts. Furthermore, the transition temperatures, as indicated by sharp breaks in the solubility curves, did not agree well with Sieverts' data. This information was of secondary importance in the earlier investigations, and the solubility at low temperatures and the transition temperatures were subject to considerable error. Therefore, a subsequent investigation, reported in this paper, was made to measure the absolute solubility at temperatures from room temperature through the melting point and make more accurate observations of the transition temperatures. Apparatus and Method The apparatus and method were essentially the same as those described in the previous work,' as shown in Fig. I. At high temperatures, the small tube containing the thermocouple in the sample container A frequently broke off, so for some of this work the thermocouple was placed outside the sample container and protected by a quartz tube of about the same wall thickness as the sample container. No significant difference was found in the transition temperatures obtained in the two ways. The automatic temperature controller was used in these tests in the regions where there was little change in solubility with temperature. In the neighborhood of the transition points a continuously variable autotransformer was used instead of the automatic controller, and the power input to the furnace was adjusted so that the temperature increased or decreased at a very slow, uniform rate through the transition range. This procedure was followed because the temperature oscillations produced by the controller were too great compared with the transition range, and the transi- . tion points determined under such conditions were less accurate. Absolute Solubility Procedure ad Results The absolute solubility of hydrogen in manganese could be determined most

Jan 1, 1947

Jan 1, 1884

By Shawn T. Sorrell, Carl Hrovatic

Original by Carl Hrovatic and Shawn T. Sorrell Revised by Carl Hrovatic Land is a precious resource and should be treated as such by all members of our society. The soil covering this earth is only a very thin outer layer, varying in thickness from a few inches to a few feet and covering the rocks and minerals lying beneath the surface. The wise use of this valuable commodity is the responsibility of everyone. Many everyday activities disturb the earth's surface. Examples are highway construction, housing and commercial developments, agriculture, and various types of mining. This chapter discusses the relationships of the environment to land as it applies to surface operations in the coal industry. Mining by surface methods disturbs, for a brief period of time, thousands of acres of land annually. In addition, refuse piles, slurry ponds, abandoned mine structures, unprotected mine openings, and unsightly cleaning plants can also adversely affect land unless properly handled. ACTIVE SURFACE MINING OPERATIONS Mining by surface methods includes rock quarries; sand and gravel pits; huge open pits to extract iron, copper, phosphate, and other ores; and coal mining. Production of coal by surface methods is now approaching 408.2 Mt/a (450 million stpy), amounting to almost 60% of the total coal output. Surface coal mining can be classified into the following five broad categories : Open-pit mining is practiced where coalbeds are extremely thick, as in some western states, or where coalbeds are sharply pitching, as in the anthracite region of the eastern United States. A typical open-pit mine, with coalbeds of 3.05 to 30.5 m (10 to 100 ft) or more thickness and a

Jan 1, 1981

By Thomas Egleston

The adoption of the regenerative principle for burning fire-bricks, pottery, etc., has been delayed beyond what would naturally have been expected, because there bas been until recently little necessity for high heat in burning such material. But the introduction of pro-

Jan 1, 1887

By James Lee Hibbard, Doraiswami Ramkrishna

A population balance model accounting for the transient variations in drop size distributions in a stirred liquid-liquid system is analyzed for its effect on chemical reaction conversion in a stirred, batch reactor. The analysis is applied specifically for phase transfer catalytic reactions, which indicates that transient effects of evolution of drop size distributions may be important in such systems.

Jan 1, 1981