Search Documents

By D. W. Gillmore, C. C. Wright

DEWATERING is a major problem in the preparation and utilization of fine-sized coals now being recovered in increasing amounts from colliery effluents, refuse banks, and silt ponds. Of the various methods which have, been proposed for dewatering fine coal, gravity drainage is probably the oldest and most widely used, and yet little information on this subject has been published. Consequently a laboratory investigation of gravity drainage phenomena was undertaken not only to provide basic data for predicting the drainage behavior of fine coals in cars, bunkers, basins, and silos, but also to obtain some understanding of the moisture retention properties of fine coal. Because of practical interest in the problem, a reproducible laboratory technique, which simulated plant conditions as closely as possible, was developed for the evaluation of drainage variables. The ap- paratus selected consisted of vertically-mounted lucite columns, nominally 4 to 8 ft in length and 2, 3 or 6 in. in diam; the bottom of the column was provided with a rubber stopper through which was inserted a -in. diam drainage tube; a wad of glass wool was placed on the upper part of this outlet tube to retain the coal and a plug was temporarily located at the lower end to prevent drainage during charging of the column, see Fig. 1. The most satisfactory testing procedure is as follows: 1—The fine coal, which has been thoroughly

Jan 1, 1953

By D. W. Gillmore, C. C. Wright

DEWATERING is a major problem in the preparation and utilization of fine-sized coals now being recovered in increasing amounts from colliery effluents, refuse banks, and silt ponds. Of the various methods which have, been proposed for dewatering fine coal, gravity drainage is probably the oldest and most widely used, and yet little information on this subject has been published. Consequently a laboratory investigation of gravity drainage phenomena was undertaken not only to provide basic data for predicting the drainage behavior of fine coals in cars, bunkers, basins, and silos, but also to obtain some understanding of the moisture retention properties of fine coal. Because of practical interest in the problem, a reproducible laboratory technique, which simulated plant conditions as closely as possible, was developed for the evaluation of drainage variables. The ap- paratus selected consisted of vertically-mounted lucite columns, nominally 4 to 8 ft in length and 2, 3 or 6 in. in diam; the bottom of the column was provided with a rubber stopper through which was inserted a -in. diam drainage tube; a wad of glass wool was placed on the upper part of this outlet tube to retain the coal and a plug was temporarily located at the lower end to prevent drainage during charging of the column, see Fig. 1. The most satisfactory testing procedure is as follows: 1—The fine coal, which has been thoroughly

Jan 1, 1953

By E. C. Houston

The presence in the Tennessee Valley of extensive deposits of olivine, a silicate of magnesium and iron that contains approximatcly 28 per cent magnesium, has been recognized since 1896 when Lewis8 published a survey of basic magnesium rocks of western North Carolina. A recent field survey by T.V.A.7 showed that more than two hundred million tons of high-grade olivine occurs above local drainage levels in western North Carolina and northern Georgia. Except for sporadic attempts to work the olivine for its nickel and chromium contents,10 the ore received little attention industrially until 1926 when Goldschmidt3 suggested its use in the manufacture of refractories. Only one instance is recorded of an attempt to utilize the ore commercially for its magnesium content;11 in this case a process was used in which olivine was treated with sulphuric acid, the resultant mixture was leached with water, and the leach solution was purified and evaporated to form epsom salts, which was the end product. As a part of its program of contributing to the development of the natural resources of the region, the Tennessee Valley Authority became interested in the olivine deposits as a source of metallic magnesium because of their high magnesium content and proximity to hydroelectric power. Studies were undertaken to determine the feasibility of producing magnesium chloride by extraction of olivine. The experimental work was carried out successively at the T.V.A. Minerals Testing Laboratory, Norris, Tenn., at the Georgia State Engineering Station,* Atlanta, Ga., and at the T.V.A. laboratory at Wilson Dam, Ala. The present paper describes a process, developed through the pilot-plant stage, whereby magnesium chloride suitable for reduction to metallic magnesium can be prepared from olivine by extraction with hydrochloric acid and subsequent purification. Research on the magnesium-from-olivine process, originally intended for peacetime use, was given impetus by the shortage of magnesium that existed at the beginning of the current world war. By the time the process was sufficiently developed to justify a proposal for its inclusion in the war program, the shortage had been met by expansion and development of other processes. However, it is believed that the magnesium-from-olivine process may have advantages that will warrant consideration of its use after the war, when the. economics of the various processes rather than production on a wartime scale will be the criterion for commercial production of magnesium. Description of Process Metallic magnesium is produced electro-lytically by the Dow and the Elektron

Jan 1, 1948

By E. C. Houston

The presence in the Tennessee Valley of extensive deposits of olivine, a silicate of magnesium and iron that contains approximatcly 28 per cent magnesium, has been recognized since 1896 when Lewis8 published a survey of basic magnesium rocks of western North Carolina. A recent field survey by T.V.A.7 showed that more than two hundred million tons of high-grade olivine occurs above local drainage levels in western North Carolina and northern Georgia. Except for sporadic attempts to work the olivine for its nickel and chromium contents,10 the ore received little attention industrially until 1926 when Goldschmidt3 suggested its use in the manufacture of refractories. Only one instance is recorded of an attempt to utilize the ore commercially for its magnesium content;11 in this case a process was used in which olivine was treated with sulphuric acid, the resultant mixture was leached with water, and the leach solution was purified and evaporated to form epsom salts, which was the end product. As a part of its program of contributing to the development of the natural resources of the region, the Tennessee Valley Authority became interested in the olivine deposits as a source of metallic magnesium because of their high magnesium content and proximity to hydroelectric power. Studies were undertaken to determine the feasibility of producing magnesium chloride by extraction of olivine. The experimental work was carried out successively at the T.V.A. Minerals Testing Laboratory, Norris, Tenn., at the Georgia State Engineering Station,* Atlanta, Ga., and at the T.V.A. laboratory at Wilson Dam, Ala. The present paper describes a process, developed through the pilot-plant stage, whereby magnesium chloride suitable for reduction to metallic magnesium can be prepared from olivine by extraction with hydrochloric acid and subsequent purification. Research on the magnesium-from-olivine process, originally intended for peacetime use, was given impetus by the shortage of magnesium that existed at the beginning of the current world war. By the time the process was sufficiently developed to justify a proposal for its inclusion in the war program, the shortage had been met by expansion and development of other processes. However, it is believed that the magnesium-from-olivine process may have advantages that will warrant consideration of its use after the war, when the. economics of the various processes rather than production on a wartime scale will be the criterion for commercial production of magnesium. Description of Process Metallic magnesium is produced electro-lytically by the Dow and the Elektron

Jan 1, 1948

By d&apos, D. L. Guernsey, J. C. Entremont, John Chipman

The reaction of aluminum with oxygen in liquid iron has been studied at 1740° and 1910°C. Interaction coefficients are very much smaller than those previously published. The equilibrium constant falls within the approximate range of earlier experiments and calculations. It is now well established that the "deoxidation constant" for aluminum in liquid steel at normal steelmaking temperatures is extremely srnall. Thus at 1600 the product [% Al] is of the order of 10- 14. At this temperature, therefore, great experimental difficulties are encountered in any attempt to obtain a direct measure of the constant. If the aluminum content of the metal is high enough to permit accurate analytical determination, that of the oxygen is too low. If the oxygen content is high, the aluminum is below the limits of detection. Our best values of the constant have come, therefore, from indirect calculations or by extrapolation downward from observations at higher temperatures.. For their studies in the range 1695° to 1866°C, Gokcen and chipman' restricted their aluminum concentrations to less than 0.06 pct. Oxygen analyses were made by the vacuum fusion method which appears to be dependable at these low aluminum concentrations. Experimental results, even at the highest temperature employed, are extremely sensitive to small errors in the analysis of either element. The slight change in the equilibrium constant with aluminum and oxygen concentration was utilized in the calculation of interaction coefficients expressing the effect of aluminum on the activity coefficient of oxygen and the reciprocal effect of oxygen on the activity coefficient of aluminum. The range of concentration, however, was so limited that only a rough value for the interaction coefficient could be obtained. This value was much more negative than that found for any other pair of reactants. In view of the very limited range of concentration employed, the reported values have always been regarded as very questionable. A redetermination was the object of the work reported here. EXPERIMENTAL METHOD At high aluminum concentrations, the vacuum fusion method is susceptible to grave error due to absorption of gas by aluminum distilled from the sample. Since it was desirable to extend the study to at least as much as 1 pct Al, another method for analysis was sought. In steels containing more than a few hundredths of a percent aluminum and no other deoxidizing element, it is safe to assume that

Jan 1, 1963

By R. G. Ward, P. L. Sachdev

Using an improved maximum bubble pressure technique, the densities of iron silicates at 1400°C have been measured under nitrogen. At the wiistite composition the density has been measured by bubble-blowing experments with both argon and nitrogen and calculated from the measured volume of a known mass of melt under nitrogen. The densities under nitrogen are significantly different from those measured under argon for melts containing less than 28 wt pct SiO2. THE constitution of liquid slags is not well understood, largely because no single property or parameter can be measured which gives conclusive evi- dence of the types and packing of the ions present. Of the many property measurements which can provide information leading to a picture of the constitution of slags, density gives the most direct evidence and has been studied extensively. The work reported here is part of a program of study of densities in multicomponent melts in which the iron oxide-silica system is the solvent. These melts are important as they are fundamental to basic steelmaking, and they allow the study of basic silicate compositions which have hitherto been largely neglected. As considerable disparity exists

Jan 1, 1965

By E. P. Shea

The Anaconda Co.'s Geological Department at Butte, Mont., was started early in the Company's history because of litigation involving vein ownership and extralateral rights. The problems, some of which were resolved in courts, were many because of the large number of veins and lode locations. Defensive action was required to prove ownership and protect against illegal exploitation of the downward and extra-lateral extensions of the ore bodies. In many cases it was necessary to define the outcrop of the vein and to show that its apex was within the boundaries of the lode claim. Exhibits illustrating geology were needed to present the cases clearly, and these could be made only after careful inspection and mapping of the underground workings by competent geologists. Also, The Anaconda Co. was one of the first companies to recognize the worth of skilled mining geologists and the value of accurate records in the search for new ore. The department was organized in 1900 by H. V. Winchell who, with D. W. Brunton, worked out the methods. Reno Sales was Chief Geologist from 1906 until 1948 when he was succeeded by V. D. Perry, the present Chief Geologist. Under their direction, F. A. Linforth, M. H. Gidel, C. H. Steele, E. P. Shea, C. C. Goddard, Jr., and W. A. O'Brien enlarged the scope of the work and improved the technique.

Jan 3, 1961

C. P. SANDBERG, LONDON, ENG : † I think we should all be grateful to the Pennsylvania Railroad Company, and to their chemist, Dr., Dudley, for spending so much time and money in order to solve an important question ; nor are we less indebted to the public spirit which leads them to impart the experience thus gained. In Europe nothing similar has hitherto been done, either by a company or by any private individual. In England the great railway companies employ their engineers in other ways, and do not keep a chemist or specialist to study rails; but even if they did they would probably not publish the results. The chief professional engineers are so occupied with their private practice of railroad construction generally, that they cannot be expected to devote their time and energies to so special a question. The German Railway Union has, in my opinion, missed the real object of its elaborate researches by falling into the error of specifying costly, impracticable tests for rails-tests at the same time which do not infallibly expose the impurities that may be in the rails under examination. There has, therefore, been nothing done on this side of the Atlantic in the way of exhaustive study to determine the best composition for steel rails. America should consequently have full credit for the enlightened example which she has set. I wish, however, to make a few remarks on Dr. Dudley's second paper, a paper which follows very much upon the same lines of argument as the first read three years ago, upon which I have previously touched in my paper on the same subject read at the meeting in August last. If Dr. Dudley had discovered a new metal he could hardly, I think, have taken more pains to prove that he was correct in his first formula for the best chemical composition of steel rails. But I have seen so much done in the way of proof by experiment that I am inclined to think that almost anything can be proved by experiments and by samples. If Dr. Dudley would only give up his formula, which would not suit any country-not even America- * For the convenience of members it has bees thought best to insert the continuation of this discussion at the Virginia meeting in tide place, rather than to delay its permanent publication until the issue of Volume X, Transactions, where it would properly belong. T. M. D., Sec'y, † Sent to the secretary in manuscript.

Jan 1, 1881

By Ray Hammond Misener

THE purpose of this paper is to describe the installation of the pumping station on the 3314-ft. level of the Carlos Francisco mine of the Sociedad Minera Backus y Johnston del Peru, at Casapalca, Peru. However, so much preliminary work was necessary before the actual installation could be started that some of that work will be described briefly, in order to clarify the discussion of the main subject. The Sociedad Minera Backus y Johnston del Peru, a subsidiary of the Cerro de Pasco Copper Corporation, owns and operates a group of mines in the Casapalca district, of which the most important are the Carlos Francisco and the Aguas Calientes. These two mines, one mile apart, are connected on their 2100 and 2700-ft. levels. These are motor-haulage levels, equipped with 3 ½ -ton Baldwin-Westinghouse locomotives operating from a 260-volt d.c. overhead trolley. A 38-cu. ft. hopper-bottom car is used. Each mine has a 2 ½ -compartment, inclined (70°) winze shaft. The Aguas Calientes shaft, operating between its 2100 and 2900-ft. levels, is used only for men and materials; whereas the Carlos Francisco shaft, between the 1700 and 2700-ft. levels of that mine, is the main operating shaft for the district. All the ore from the Carlos Francisco and the Aguas Calientes mines is hoisted through the Carlos Francisco shaft. The ore produced in these mines is by-passed to the 2700-ft. level, where it is gathered by the electric trains, taken to the Carlos Francisco shaft and dumped into an ore pocket in front of the shaft. The ore is hoisted to the 1700-ft. level in 2-ton self-dumping skips and emptied into a 150-ton loading pocket. There it is loaded into electric trains and despatched to the concentrator through the Backus and Johnston tunnel, which is the main entry from Casapalca to all the mines in the Backus and Johnston group. DEVELOPMENT PROGRAM In 1934 the following development program was outlined for the Carlos Francisco and the Aguas Calientes mines: (1) to deepen the Carlos Francisco shaft from the 2700 to the 3400-ft. level, (2) to deepen the Aguas Calientes shaft from the 2900 to the 3300-ft. level, and (3) to connect the two shafts on the 3300-ft. level with a motor-haulage crosscut. Each mine was to be developed also on intermediate levels (2900 and 3100). The three levels were to be spaced 54 meters (177 ft.) floor to floor, measuring from the 2700-ft. level along the incline of the shaft. The Carlos Francisco mine, together with the section between it and the Aguas Calientes mine, produces 10,000 gal. of water per minute. A fault to the north

Jan 1, 1943

By Oscar Glaeser

THE purpose of this paper is to present specific applications of the fundamental principles of mine ventilation and the means that are at our disposal to accomplish the task of maintaining a healthful atmosphere in small mines and prospect openings.

Jan 1, 1936

By E. P. Whittemore

Experience with the ASC multipoint gas lift system was obtained in Colonia zone of the West Montalvo field near Oxnard, Calif. The wells in this pool produce from depths varying from 10,500 to 12,000 ft. Oil gravity is generally 14 to 15' API with a few extremes of 12 and 20" API. Some salt water is produced which causes some very viscous emulsions. Viscosities at 150F (which is the approximate wellhead temperature) vary from 5,000 to 100,000 SSU. Most of the production is by gas lift, although a few wells are produced by rod and hydraulic pump. About half of the gas-lift wells are on continuous flow and the remainder are on intermittent lift using large, ported, pilot-operated valves for single-point transfer of gas from casing to tubing. Gas-liquid ratios vary from about 6 to 10 Mcf/bbl of gross fluid lifted. Wells are produced to a 450-psi trap system. The following remarks will be confined to intermittent lift only, since this is the type of lift which has been achieved with the ASC valve system. The maximum gross fluid which has been produced by single-point intermittent lift is about 350 B/D in 3-in. tubing and 200 B/D in 21/2-in. tubing with gas-liquid ratios of approximately 7 to 9 Mcf/bbl. Some design changes could reduce this ratio. The ASC multipoint system has provided production as high as 480 BOPD in 21/2-in. tubing with gas-liquid ratios just under 4 Mcf/bbl. To be able to apply the multipoint system, it is recommended that a detailed explanation be obtained concerning transition-point pressure and stabilizer setting—what its significance is to the string design, how it may work for or against the operation of the well, how it is related to tubing sensitivity and how it affects the unloading operation. The unloading operation may only be of academic interest in a technical paper, but to the production foreman, unloading and setting the valves in operation is a very real problem and should be understood in detail. One item touched lightly in the paper was the unloading valve. This valve controls the maximum pressure at which the well can be operated. When lifting heavy viscous fluids, it is most important to set this valve for the maximum possible realistic operating pressure at the surface. If the well lifts easily, it is simple to set the ASC valves at a lower operating pressure and the unloading valve will remain closed; but if the well happens to be heavier to lift than anticipated, it may be desirable to operate on the unloading valve itself and use all the energy obtainable at the bottom of the hole. In the Colonia pool very heavy wet-gas gradients are experienced due to the viscosity of the liquid and the dense mist which is left behind a slug of fluid. There are many combination strings of 3- and 21/2-in. tubing. This aggravates the wet-gas gradient problem and provides wet-gas gradients of about 50 to 70 psi/1,000. An advantage which multipoint lift has provided is increased slug efficiency through better maintenance of pressure under the slug and decreased fall back as the slug passes up the tubing. By using multipoint injection, wet-gas gradients have been reduced to about 30 psi/1,000. This has reduced bottom-hole operating pressure and given a production increase. The ASC valve is not a simple device. It's operation is difficult to understand, and it must be understood to be used efficiently in gas-lift design. Operating problems are difficult to diagnose—whether they be caused by the fluid lifted, valve malfunction, lift gas rate, or operating pressure. Calculations and reasoning are required to find out what is causing the problem. Inherent in the ASC valve is the inability to create large pressure differentials across a slug. Large differentials may be required to overcome the inertia of very viscous fluid as it is being accelerated in the bottom of the hole. This is tied back to the design of the unloading valve and is one reason for the importance of setting the unloading valve for the highest possible operating pressure. ~u; to the narrow spread the ASC valves provide, it is impossible to cycle slower than about 24 cycles/day on choke control. If small production of 150 BOPD and less is expected, a surface time-cycle controller will be required if the most economical operation is to be achieved. To achieve a satisfactory operation, the operator must keep a record of any changes made in the operating pressure of the ASC valves. Anything which may cause changes in casing pressure in excess of the stabilizer setting will change the valve operating pressure, and if this is not noted from daily inspection of the well casing-tubing pressure recorder charts, the operator will lose control of the well. Significant results can be achieved using ASC valves; however, considerable knowledge is required to design with them, and attention to detail is required for satisfactory field operation.

Jan 1, 1965

By N. Brown, M. Herman

IT has been pointed out by Cottrell' and Fisher that long-range order would produce superdis-locations, consisting of two partial dislocations separated by an out-of-phase region. The mutual repulsion of the partial dislocations is balanced by the surface tension of the out-of-phase domain boundary joining the dislocations (Fig. 1). The calculation of the equilibrium spacing of the dislocations has yet to be made. The argument uses the Bragg and Williams theory of long-range order." The metal under consideration is the A-B, body-centered type, such as ß brass. The slip system is taken to be [Ill], (110). Since nearest-neighbor interactions are considered, only the atoms position in the two (110) planes adjoining the slip plane have to be labeled. Corner sites are called a and a' in the top and bottom (110) planes, respectively. Similarly ß and ß are the body-centered sites. Thus, a and ß and 0 and a sites are nearest neighbors. Assume that the bottom plane moves and the top plane is fixed during slip; the atoms in a and ß sites exchange sites but atoms in a and ß sites remain fixed. Fraction of A atoms in a sites, for example, is given by fa and fa. for the un-slipped and slipped condition, respectively. Similarly number of A atoms in the a sites is given by n, and n'a for the unslipped and slipped condition, respectively. As the dislocation moves into the ordered region the change in number of A-A bonds is given by

Jan 1, 1957

By Victor M. Braschi

The railroad history of Mexico began with the first presidential term of General Diaz. Concessions for the building of railroads had been granted in former years; indeed, an exclusive privilege was granted, August 22, 1837, to Francisco de Arrillaga for the construction of a railroad from Mexico to Vera Cruz, with a branch to Puebla, and other concessions were granted from then on at various periods; but the year 1877 was the real beginning of the regular and constant decelopment of the railways of Mexico. The programme laid out at that time by the new government, and responded to by the nation, was to develop its natural ele-

Jan 1, 1902

By J. C. Sullivan, W. A. Knoll

THE sinking of a new shaft at the Newport mine, Ironwood, Mich., was started in May 1931 and completed on Aug. 3, 1932. During this period, 2665 ft. of shaft in granite was completed, at an average advance of 6 ft. per 24 hr. In November of 1930, experimental work was con- ducted on 65 ft. of shaft through 22 ft. of overburden where ledge was encountered, and this work convinced the operators that all drilling could be done with vertical holes with the blasting relief to a 4%-in. hole drilled vertically in the center of the cut. The reason for not adopting the conventional V-cut was to get away from damaging the shaft steel. The blasting in a V-cut naturally tends to throw the broken material upward, but with the cut as adopted the relief was in a horizontal direction to a large extent. The scheme of mucking employed made it necessary to keep the steel shaft sets within 50 ft. of the bottom at all times. This could not be done without serious damage with a V-cut when blasting in granite. The cut as drilled also broke 10.83 ft. per round of drilling, which was considerably more than the experience with a V-cut in the same material. The extended cut reduced proportionately the delays for charging, blowing smoke and handling drilling equipment in the shaft. Another advantage was the ease in drilling vertical over inclined holes, and the preservation of the proper spacing of the drill holes at the bottom of the cut. DRILLING Air was carried down the shaft in an 8-in. flanged pipe line at a pres- sure ranging from 95 to 100 lb. This line was extended to within 100 ft. of the bottom, where a valve and a 4 by 4 by 6-ft. tee was connected to it. To each side of the tee was connected a nipple and elbow, the resulting span of the two elbows being about 4 ft. Lengths of short 3-in. hoses

Jan 1, 1938

By S. W. Kessler, R. B. Pond

Metal specimens were solidified through a measured thermal gradient so a free surface and the liquid-solid interface could be examined. A line structure was observed on the surface and a hexagonal structure on the interface. A model to explain these forms is proposed. NUMEROUS observations of the dendrite form have been made both in nonmetallic and metallic systems. From these, extrapolations have been made as to the probable dendrite form in pure metals. Observations of the dendrite form in pure metals, nevertheless, have been scanty. In general, these observations have been made on the skeleton dendrite after the mother liquid has been drained from around it, and a mechanism of the formation of the dendrite has been postulated from this solid form. Recent investigations have been conducted in an endeavor to make a study of the formation of the dendrite in several pure metals and the effect of several variables on this mechanism and final form. For these investigations, an apparatus was designed and constructed as shown in Fig. 1. It consists of a talc block containing a half-cylindrical depression, the end of which terminates in the conical recess of a copper block having an external attachment for cooling. A heating coil extends the length of the mold just beneath the lower limits of the cavity. The entire cavity for holding metal is coated with a thin film of graphite. Six thermocouples are equally spaced in the cavity and under the graphite, and six microammeters indicate the temperatures at the particular thermocouple stations. Readings were taken of all meters at the same instant time measurements were taken by photographing the panel of microammeters and a stop watch which was started at the beginning of the run. It was possible with this apparatus to solidify metals through a measured thermal gradient and to observe the progression of the liquid-solid interface with time by following the formation of the dendrite markings in the surface of the solid material. These

Jan 1, 1952

By Stuart M. Buck, J. H. Bramwell, Edward H. Williams

The Southwest Virginia Improvement Company began operations in the Bluestone Flat-Top coal-field, situated in Tazewell County, Virginia, in the fall of 1881. In May, 1883, the company had built 200 coke-ovens, and by March, 188-1, had 9000 feet of entries, exclusive of air-ways, in the Nelson or Rig coal-bed of this district (which here averages eleven feet in thickness), and had extracted 200,000 tons of coal, representing an area of about twenty acres. About this opening has grown the recently incorporated city of Pocahontas, and the completion of the New River branch of the Norfolk and Western Railroad to this point enabled the company to make large contracts for supplying coal and coke, so that it was deemed necessary, on account of the limited area developed, to work the mine day and night to fill orders. At 1.30 Thursday morning, March 13th, the inhabitants of Pocahontas were awakened by a violent shock, and within a few minutes all knew that the East mine had been the scene of an explosion of so general a nature that, of the 114 men at work, not one had escaped. The daily papers gave more or less distorted accounts of the number of victims, the scenes in and about, the mine, and the probable cause of the disaster. At the request of the company, the President of the American Institute of Mining Engineers appointed the undersigned a committee of three to investigate the matter, and the committee thus constituted presents the following report, accompanied by a copy of the testimony taken daring the investigation, for preservation in the archives of the Institute. Pocahontas was reached on Thursday, April 24th, and left on Friday, May 2d. During this interval the committee made repeated visits to the mine, especially to the points, of most importance, examining it carefully in every part; and summoned a number of witnesses, twenty-six of whom appeared and testified. The mine had been left in the same state as when the bodies were

Jan 1, 1885

By Hallan N. Marsh

The subject of this paper is apt to bring to mind wells ranging from 6000 to over 8000 ft. in depth. However, it is uncommon to pump wells at depths greater than about 5000 ft. Fig. 1 shows the number of wells being pumped at various depths by one company in Southern California. A few companies have a very few wells pumping at depths greater than this. This paper will deal with wells between 3000 and 5500 ft. in depth. Most California oils at these depths are between 25" and 35" gravity. The subject is so broad that it will be necessary to omit many interesting phases, and to treat others very briefly. Power, power transmission equipment, power efficiency, counterbalancing, sucker rods, pumps and volumetric efficiency will be discussed. Power As a source of power, the 50/20-hp. electric motor is generally preferred. Input is generally between 10 and 25 hp. Due to the uneven-ness of the load, an input of 20 hp. on the low range is generally about all that these motors will carry without overheating, in spite of their overload capacity. In some cases the capacity of the motor limits the speed

Jan 1, 1929

NEW YORK SECTION ALLEN H. ROGERS, Chairman, H. C. PARMELEE, Vice-chairman, FOREST RUTHERFORD, Vice-chairman, W. S. DICKSON, Secretary, 71 Broadway, New York, N. Y. J. E. JOHNSON, JR. . F. T. RUBIDGE, Treasurer, P. G. SPILSBURY. The annual meeting of the New York Section, for the election of officers and other business, was held at the Machinery Club on May 23,

Jan 8, 1918

By F. J. Smit

The Tintic Division of Kennecott Copper Corporation operates the Burgin Mine in the East Tintic District near Eureka, Utah, approximately 75 miles south of Salt Lake City. The Division was organized in 1963 to develop concealed replacement orebodies in the area located by Bear Creek Mining Company, Kennecott's domestic exploration subsidiary. Several accounts of the discovery of these orebodies and the general geology of the area have been given (1, 2). The ore is very complex and of varying degrees of oxidation and alteration. The principal metal values are lead, zinc, silver, and cadmium. The Burgin No. 2 shaft was sunk in 1963 to provide access for mining the orebodies. Much of the ore mined after this shaft was sunk was high grade and shipped directly to smelters, but concurrently it was recognized that concentration would be required to upgrade the lower grade ore in the deposits. Accordingly, in January 1967, authorization was received to construct a 500 tpd concentrator. From the beginning it was expected that the characteristics of the mill feed would vary widely and unpredictably as mining progressed. This paper summarizes the characteristics of the ore, the test work upon which the plant design was based, the engineering and construction, and the present operation of the facility eighteen months after startup. ORE CHARACTERISTICS The Burgin ore is a complex assemblage of minerals from replacement of limestone. The replacement and alteration occurred in at

Jan 1, 1970

By Joseph Perry

MAGNESITE is found in 22 California counties, but many of the deposits are too small or too impure to be of commercial value. Several of sub-stantial size and quality were entirely exhausted by wartime operation. At present, three properties comprise the only known workable deposits in the state. Of these, the Western mine and the Patterson mine have been known and worked for many years, and have been described in con-siderable detail in various publications, therefore need only brief mention here, because of their proximity to the Bald Eagle mine. The latter, recently developed, is unusual in type of ore deposit, plant design and operation, as well as products made, and very little has been written concerning it. WESTERN MINE The Western mine, 32 miles south of Livermore, Calif., was formerly operated by C. S. Maltby. It has been a consistent producer for many years.1 The ore is of amorphous variety, occurring along fracture zones in serpentine. The veins vary greatly in width, the average being perhaps 8 ft., with the maximum indicated in one early stope of 40 ft.; 2 ft. is considered the minimum for economical mining. The strike of the veins is predominantly north and south, with dip to the west varying from 40° to 75°. Walls are well defined and as a rule firm and easily supported, Veins range in length from a few hundred feet to 1000 or more. Their maximum vertical extent is about 350 ft., but many run less. Early mining consisted of open-cut and glory-hole work on the larger outcrops. This was followed underground by a modified shrinkage system, the waste and low-grade horses being removed by hand sorting on the tramming levels and transported to surface dumps. Filled-stope mining is used now, in order to eliminate the handling of waste, which has

Jan 1, 1938