Search Documents

By Gligorije Stankovic

This paper describes the fluo-solids roaster and acid plants at the new 40,000-TPY Trepca electrolytic zinc plant. The electrolytic zinc plant units were constructed to the design of Singmaster and Breyer, New York and began operation in mid-1967. The fluo-solids roaster plant, constructed according to the design of Dorr-Oliver, Paris, includes concentrate handling and storage facilities; two independent concentrate roasting circuits, each with a 110 to 155 TPD fluo-solids roaster; waste heat boilers; cyclones; electrostatic precipitators; calcine coolers; and calcine conveyors. The acid plant uses the "Petersen system" contact process. The plant has one acid circuit with a capacity of 230 tons of monohydrate per day. Gases for the acid plant are obtained from roasting zinc concentrates. When the roaster plant is operating at maximum capacity, excess SO2 is used in two other Petersen System circuits in the near vicinity.

Jan 1, 1970

By Will H. Coghill, Fred D. DeVaney

THE coercimeter, as its name implies, is an instrument for measuring the coercive force[+] of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub- sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. The turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1938

By Ingvar Janelid

DURING the last ten years, in the effort to save manpower and costs, methods of drilling and blasting in Sweden have changed and developed in a revolutionary manner. These developments have been accompanied by extensive alterations in methods of tunneling and in mining technique. Since the end of the 1940's there has been a 100 pct change-over in Sweden to the use of tungsten carbide tipped drill steel. Both investigations and practical results have shown clearly that a tungsten carbide chisel bit fastened directly on the drill steel is the most economical for Swedish conditions. This applies to drill steel up to the longest size it is practical to handle. In terms of drilling footage, durability of the drill steel and the tungsten carbide bit is generally the same. In this respect, therefore, a detachable bit offers no advantage over integral steel. Transportation of integral steel to the grinding plant, instead of detachable bits only, involves heavier work, but this is counteracted by placing grinding plants closer together or by grinding at the working place itself. The drilling rate with integral steel is higher, the trouble of changing bits is avoided, and the difficulties which always arise with joints are eliminated.

Jan 6, 1954

By R. E. Ford, P. Tarassoff, P. H. Jennings

Copper oxide ore may be leached at all sizes from run-of-mine down to pulp, and consideration must be given to all available methods in determining the most economical one. Heap leaching was evaluated in a pilot plant at Gaspe Copper Mines, Ltd. which was designed to simultaneously leach two 1200-ton dumps of ore. The plant was operated for two years, in part under severe winter conditions. Two modes of leaching were investigated: acid leaching in which sulfuric acid was added externally to the leach solution, and pyritic leaching in which pyrite concentrate was added to the dump and acid was generated in situ by bacterial action. The pilot plant operation is described, and the results are compared with laboratory data obtained in 6-in.-diam columns. It is concluded that pyritic leaching offers certain operating advantages over acid leaching when copper is recovered by cementation in that iron buildup in the solution is prevented.

Jan 1, 1974

By E. C. Babson

In order to explore the possibility of predicting reservoir performance from laboratory data, behavior of a hypothetical low-permeability reservoir has been estimated by applying data and methods currently available in the literature. A method of calculating decline in productivity index is discussed, and recoveries by internal gas drive, external gas drive and water drive are estimated. Introduction During the life of a producing oil property an operator is faced with many perplexing problems. Any attempt to determine proper well spacing, optimum rate of production, or the desirability of pressure maintenance requires the evaluation not only of a host of economic and practical operating factors but also of the future performance of the reservoir. Although in some cases economic or operating con-siderations may be of primary importance in planning a development or production program, the anticipated effect on ultimate recovery is more likely to be the decisive factor. The soundest basis for evaluating reservoir performance is past experience with oil fields, but pertinent data are difficult to obtain or apply under conditions normally encountered in California fields. Many of these fields are characterized by thick sections of alternating sands and shales complicated by faulting and rapidly changing lithologic conditions. Further compli- cations are introduced by haphazard development and production practices resulting from competitive conditions, changing demand for oil, and insufficient knowledge of structural conditions during early development. Even in the rare cases where development has been systematic and adequate, production policy has usually been controlled by economic and competitive factors rather than a desire to obtain information for use in future operations. In other words, comparable reservoirs in which development and production practices have been systematically varied are seldom found. In the light of these conditions, conclusions based on experiences usually lack the certainty required for decisions involving large sums of money. Some other method of attacking these problems is needed to supplement and orient field experience. Progress in laboratory investigations of the flow of oil, gas, and water through sands has been so rapid in recent years that these data may furnish such a supplementary approach in the near future. In order to explore this possibility the author has attempted to predict the behavior of one type of reservoir by applying published data and methods. Basic Data and Assumptions Calculations outlined in this paper are dependent upon a detailed knowledge of the properties of oil, gas, and water present in the reservoir and the portion of the total pore space originally filled by each. It is also necessary to know how the permeability of the sand to oil, gas, and water varies with the saturations of these fluids 20

Jan 1, 1944

By E. C. Babson

In order to explore the possibility of predicting reservoir performance from laboratory data, behavior of a hypothetical low-permeability reservoir has been estimated by applying data and methods currently available in the literature. A method of calculating decline in productivity index is discussed, and recoveries by internal gas drive, external gas drive and water drive are estimated. Introduction During the life of a producing oil property an operator is faced with many perplexing problems. Any attempt to determine proper well spacing, optimum rate of production, or the desirability of pressure maintenance requires the evaluation not only of a host of economic and practical operating factors but also of the future performance of the reservoir. Although in some cases economic or operating con-siderations may be of primary importance in planning a development or production program, the anticipated effect on ultimate recovery is more likely to be the decisive factor. The soundest basis for evaluating reservoir performance is past experience with oil fields, but pertinent data are difficult to obtain or apply under conditions normally encountered in California fields. Many of these fields are characterized by thick sections of alternating sands and shales complicated by faulting and rapidly changing lithologic conditions. Further compli- cations are introduced by haphazard development and production practices resulting from competitive conditions, changing demand for oil, and insufficient knowledge of structural conditions during early development. Even in the rare cases where development has been systematic and adequate, production policy has usually been controlled by economic and competitive factors rather than a desire to obtain information for use in future operations. In other words, comparable reservoirs in which development and production practices have been systematically varied are seldom found. In the light of these conditions, conclusions based on experiences usually lack the certainty required for decisions involving large sums of money. Some other method of attacking these problems is needed to supplement and orient field experience. Progress in laboratory investigations of the flow of oil, gas, and water through sands has been so rapid in recent years that these data may furnish such a supplementary approach in the near future. In order to explore this possibility the author has attempted to predict the behavior of one type of reservoir by applying published data and methods. Basic Data and Assumptions Calculations outlined in this paper are dependent upon a detailed knowledge of the properties of oil, gas, and water present in the reservoir and the portion of the total pore space originally filled by each. It is also necessary to know how the permeability of the sand to oil, gas, and water varies with the saturations of these fluids 20

Jan 1, 1944

By C. A. Heiland

FOR the past three years, the senior writer has carried out, with inter-ruptions, a series of investigations into the characteristics of prospecting seismographs of a wide variety of construction. Early in 1932, a com-plete equipment was developed for both refraction and reflection observa-tions; its first function being, however, the application in reflection shooting. The performance of the equipment proved to be highly satis-factory in a series of field tests' which were carried out by the junior writer, whose services were loaned to the Colorado School of Mines by courtesy of the Plains Exploration Co. in Denver. The various problems that were encountered in the construction of the equipment, in its application in the field, and in the interpretation of the results, are fully treated in Publication 47 of the Department of Geophysics of the Colorado School of Mines. Its first part deals with the various problems encountered in the design of the instruments, and presents a discussion of such topics as the free and forced oscillations of damped and undamped mechanical seismographs, the action of oscil-lographic recording instruments and amplifiers, the characteristics of electromagnetic seismographs, and the requirements of damping, natural frequencies and static magnification for the pickups, amplifiers and oscillographs used in refraction and reflection seismographs. Further-more, a detailed discussion of the various methods of static and dynamic tests of seismic receivers, and a description of the reflection equipment developed at the School of Mines is presented. Unfortunately, a delay has occurred in the publication of the first part of this investigation concerning the instrument problems. There-fore, the second part, dealing with the field problems, is herewith pre-sented first.

Jan 1, 1933

By H. Scott

IN a paper read before the Institute of Metals, Rosenhain 1 described a new type of furnace designed primarily for the thermal analysis of metals by the inverse-rate method and used by him in the metallurgical department of the National Physical Laboratory with considerable success. In his discussion of this furnace, Rosenhain pointed out some difficulties met with in its operation, such as uniformity of rate of heating or cooling being inadequate for the degree of accuracy aimed at. To overcome this difficulty, he suggested, in place of motor propulsion, a gravity drive controlled by a"hydraulic cylinder with a relief valve whose width of opening can he regulated to allow of any desired rate of motion." The authors, in constructing a thermal-analysis furnace of Rosenhain's type, have therefore followed this suggestion and also added certain features that increase somewhat the convenience and simplicity of its operation. Requests for information regarding this furnace and the highly satisfactory results obtained from its use, it is believed, justify describing its construction and operation in sufficient detail to make possible its duplication or improvement. Description of Furnace.-The details of the furnace construction are shown in Fig. 1, which is drawn to scale. The heating tube is of /4 in. (6.35 mm.) wall "alundum" heated at the upper end by seventeen turns of 0.52 mm. platinum wire, which is coated with "alundum" cement supplied for this purpose. The cement coating is essential when a high temperature (over 1000° C.) is required, as it prevents hot spots with the resulting burning out of the heater. This platinum-wire winding, unlike "nichrome," is entirely satisfactory for temperatures of at least 1000° C. It has been maintained at that temperature continuously for 2 months and shows no signs of deterioration. This temperature is maintained by a current of 5 amp. drawn from 30 volts potential, so its necessarily continuous operation is quite economical.

Jan 8, 1919

By Chas. A. Dobbel

The Chief Consolidated properties are situated in the Tintic mining district of Utah, being included in Juab and Utah Counties, about 70 miles south of Salt Lake City. The drilling referred to in this paper has been carried on in the Chief Consolidated No. Pmine, the Gemini mine, and the Eureka Hill mine at Eureka, the Grand Central mine, above Mammoth, and the Apex Standard mine just south of Dividend. The occurrence of ore through the district is typically in lenses on bedding or breaks, and in connecting pipes, without accurate geometrical trend so that the ratio between the total length of development in drifts and crosscuts to the square feet of ore exposed is very high. A section of one of the western channels (Fig. 1) through the Tintic district, shows, roughly, the irregularities calling for excessive development work, so typical of the Tintic mines. This irregular trend of the ore constantly calls for excessive cutting up of the whole area for offshoots and the connecting links always present. In the planning of prospecting and development, no regular system may be laid out without overlooking some orebodies or segments of orebodies. It was with these facts in mind that Cecil Fitch, the general manager of the Chief Consolidated Mining Co., decided that some method of drilling was the more feasible way of successfully cutting up and bringing about the discovery of ore believed to exist; yet this drilling had to compete with a great margin of cost over crosscutting, as a crosscut in the Tintic district, even though barren, brings out geologic facts that, in many cases, are worth the price of the working itself. Diamond drills met with the success that might be expected in a district that has a reputation for the Gear and loss of diamonds; after 6 or 8 months, this method was discarded on account of the high costs. Simultaneously, a small churn drill outfit was set up underground but a few shifts proved its inapplicability. At the same time, the ordinary hammer drill was used to drive prospect holes with jointed steel. Just what equipment to develop for this work with the hammer drill involved much experimenting, as nothing was found in the literature

Jan 1, 1925

By R. H. Thielemann

THE conventional short-time tensile test provides a reliable means of predicting the sustained load-carrying capacity of steels only when the temperature is such that continuous plastic flow does not occur. At elevated temperatures, stresses considerably less than the short-time rupture value may produce continuous flow, with fracture occurring only after long periods of time. The amount of flow or creep accompany-ing failure varies for different steels, and depends, to a large extent, on the temperature and the duration of the test. Service records of cracking stills, steam superheaters and high-temperature boilers have shown that brittle fractures sometimes occur with little or no warning. In installa-tions of this type, localized stresses are often encountered, and steels must be capable of withstanding a certain amount of deformation without fracture. The sustained-load rupture test determines the expected life and corresponding ductility of steels at various stresses and tempera-tures. It also yields additional information regarding the effect of micro-structure and metallurgical stability on the high-temperature properties.

Jan 1, 1939

By Samuel Daniels

Aluminum-base alloys containing small amounts of copper and magnesium possess but ordinary physical properties as sand cast, but may be treated to give a remarkable range of tensile values and of Brinell hardness. The high-copper (4.5 per cent.) duralumins must be given a protracted treatment which in nature resembles the malleableizing of white cast iron; the low-copper (2.25 per cent.) duralumins develop an excellent combination of strength and ductility with a treatment which requires a maximum of 5 hr. to be completed. THE wrought alloys of aluminum with small amounts of copper and of magnesium have, with the development of the automotive and aircraft industries, sprung into prominence through the medium of duralumin; but the cast alloys remained in the background because their possibilities in the heat-treated condition were either not recognized or not fully investigated. In 1919, the Bureau of Standards published a preliminary survey1 of this field, which pointed out that, in general, the ultimate strength and the percentage of elongation of the alloys of aluminum with and without magnesium could be improved by so simple a treatment as heating to 932° F. (500° C.) for 2 hr., cooling in, air, and aging at room temperature for several days. British investigators, too, working with chill-cast material, found that " considerable improvement in the mechanical properties of copper-aluminum alloys' may be obtained from suitable heat treatment applied to castings."2 Jeffries and Gibson3 made the first contribution to the literature dealing exclusively with the heat treatment of sand-cast aluminum-base alloys, describing the effect of small additions or of combinations of copper, magnesium, and iron on the response to a short heat treatment comprising heating at 932° F. in a

Jan 7, 1924

By J. T. Norton, N. J. Grant, I. S., Servi

Coarse grained high purity aluminum was tested in creep at temperatures of 400° to 1200°F to develop subgrain structures. Measurements of subgrain size, distribution, and rotation were made from X-ray diffraction patterns. Subgrain size and distribution were checked metallographically and the size was compared with average slip band spacing. The slip family was determined for several specimens. THE interest and research recently evident abroad in the role of subgrain formation and polygon-ization as a contribution to the creep of metals at elevated temperatures is deserving of greater attention in this country. Such metallic subgrains can be defined as macroblocks existing within the grains. The general observation has been that the macro-blocks which belong to the same grain have a maximum difference in orientation of a few degrees. In spite of the considerable amount of work that has been done since Jenkins and Mellorl observed the "division of existing crystals into smaller units when deformation occurs at an annealing temperature," the subject of subgrain formation is only now receiving truly active discussion and investigation. The existence of subgrains has been revealed by metallographic methods, as in the work of Jenkins and Mellor,1 and by X-ray methods, first applied to this problem by Homes.' Hirst3 and Calnan and Burns4 applied the back-reflection Laue technique to the study of coarse grained specimens. Wood et al.5 and Greenough and Smith' examined the ring obtained with a back-reflection camera for the study of fine grained specimens. In addition to the above, the transmission technique was used by Wood.6 A special technique was developed by Guinier and Tennevin8 in order to improve the resolution. Metallographically, the subgrains have been observed directly on the surface of deformed specimens by Wood et al.,3 or have been made evident on repolished surfaces by applying a suitable etching reagent. The latter technique, first suggested by Lacombe and Beaujard,9 was then improved by Wyon and Crussard.10 Subgrains can be formed in single crystals after small amounts of bending followed by heating after this cold work, or during deformation at elevated temperatures. The first phenomenon was analyzed by Cahn11 for the simple case of pure bending followed by annealing. Cahn suggested a mechanism of subgrain formation based on the dislocation theory and called this phenomenon "polygonization." He extended this mechanism to the more complex case of local bending, such as the bending which may occur when a polycrystalline specimen is deformed in tension. Cahn's suggestion was later found quite consistent with the results obtained by Dunn and Daniels." An explanation has been presented recently regarding the formation of subgrains during deformation at elevated temperatures by Chang and Grant.'" In general, there are two schools of thought on the subject. One, according to Wood et al.,5 is that subgrain formation is a mechanism of deformation which is operative under certain conditions in the same way that the slip process is the mechanism of deformation which is operative under other conditions. The boundaries between the subgrains undergo a viscous flow which contributes substantially to the deformation of the material. The second, according to Cahn,13 Wyon and Crussard,10 and Chang and Grant,18 is that subgrain formation is the effect of simultaneous deformation and annealing and is,

Jan 1, 1953

By Oscar Lee

RESERVE Mining Co., owned jointly, by Armco Steel Corp. and Republic Steel Corp., controls 9% miles of magnetic taconite ore on the eastern end of the Mesabi Range lying between Mesaba and Birch Lake. The ore reserve which can be mined by open pit methods is conservatively estimated at 1.5 billion tons under a shallow, loose overburden requiring no rock stripping. Taconite now being mined is in the upper cherty horizon. It has been metamorphosed by the intrusion of gabbro and most of the iron oxide is altered to magnetite. The nonmagnetic portion of the iron is practically all in the form of silicate. The magnetic iron is finely disseminated through the rock and requires grinding -150 mesh for clean liberation of the iron oxide from the gangue.

Jan 5, 1954

By Harold L. Hinds

The Homestake Ledge or Lead was discovered by Fred and Moses Manuel on April 9, 1876. They recovered a small amount of gold from the quartz outcrop, but, unfortunately, they were prospectors not hardrock miners. Their claim was sold to a group of experienced California mining men in 1877. These mining men incorporated their holdings as the Homestake Mining Company. This was the beginning of one of the greater gold mining enterprises of the Western World. Metallurgical operations progressed over the years from an eighty- stamp grinding circuit using amalgamation for recovery to the more complex circuit of today. The Homestake Mine, today, is an underground mine with the deepest winze reaching the 8,000-foot level. The ore is hoisted to the surface by two primary shafts, the Ross Shaft and the Yates Shaft. See Figures 1 and 2. It is crushed in three-stage crushing plants located in the headframes. From here, it is trammed to the mill fine- ore bins by electric locomotives. The Lead grinding plant milling circuit, known as the South Mill, receives ore from the crushing plant at minus 112 inch (Figure 3). This material is dumped into overhead fine-ore bins from five- ton rail cars. The fine-ore bins have a live capacity of about 3,700 tons. The South Mill bins can also be fed by a conveyor system which reclaims ore from an 80,000-ton capacity stockpile. This stockpile is built up from peak mining production periods and available surface low grade material. It is then reclaimed during low mine production periods. The grinding circuit at the South Mill consists of four rod mills in open circuit followed by four ball mills in closed circuit. Three of the rod mills are 6-foot by 12-foot Marcy's. The other is

Jan 1, 1983

By R. M. Porter

The Sullivan mine of Consolidated Mining and Smelting Co. of Canada Ltd. is located one mile west of Kimberley. With its daily production of 10,000 tons, the mine is the largest in British Columbia and one of the outstanding mines of the world. The Sullivan orebody dips from nearly horizontal to 45". The ore zone is a bedded replacement de- posit in argillite with a width varying from a few inches up to 300 ft. The main sulfide minerals are pyrrhotite, pyrite, galena, and sphalerite. The chief metals produced are lead and zinc, with less important qualities of iron, silver, tin, antimony, bismuth, cadmium, indium and sulfur.

Jan 12, 1963

By M. R. Pickus, C. H. Mathewson

THE study of the plastic deformation and recrystallization of metals has been the subject of many investigations. In regard to the simple deformational processes, such as tension and compression, the early knowledge gained from studies of polycrystalline material has been supplemented by many significant researches on the behavior of single crystals. Unfortunately, this has not been true for more complicated deformational processes. As far back as 1927, G. I. Taylor1 wrote: It is impossible in the present state of knowledge to do more than give a possible reason why (face-centcred cubic) crystals set themselves with a (110) direction in the plane of rolling, and at right angles to the direction of rolling. The explanation of why the orientation of the crystal axes round the transverse direction is what it is, must be left till the distortion of metals, and particularly single crystals of metals in the process of rolling, has been studied in greater detail. That this gap in the systematic study of deformation and recrystallization has not yet been filled was indicated by C. H. Samans,2 who wrote in 1934 that "only four investigations upon cold-rolled single crystals of any of the face-centered cubic metals have been reported in the literature." Of these four studies, only those of S. Tanaka3 and T. Sakao,4 both of whom worked with aluminum crystals, had quantitative significance. The other two, carried out by F. Wever5 and W. G. Burgers," were of a qualitative nature. It is our hope that the present investigation may contribute something to the knowledge necessary for a rationalization of the origin of rolling textures in terms of the known behavior of single crystals, and may add pertinent information concerning the recrystallization characteristics of deformed single crystals.

Jan 1, 1938

By J. B. Dyess, H. A. Miley

Tarnish films on some of the common metals (particularly on copper and silver) have been of much scientific and commercial concern for a long time, but before the development of the electrical method1 of measuring film thicknesses there was no satisfactory quantitative approach by which to study the separate parts of these complex films. This method has been adapted to the measurement of duplex (cuprous-cupric) oxide films on copper.2 In the present work it has been used to measure tarnish films on copper when they were mixtures of cuprous oxide and cuprous sulphide, and also when they contained cuprous oxide, cupric oxide and cuprous sulphide, each component part being measured at a different potential value. Oxide-coated copper specimens, prepared by heating copper in air at chosen temperatures for given periods, were exposed to moist hydrogen sulphide in air to forml the various oxide-sulphide films studied. The comparative resistances afforded by (I) different thicknesses of oxide films, and also (2) equal thicknesses of oxide and sulphide films, against severe attacks of hydrogen sulphide were measured. The electrical method requires that the time be observed for the cathodic reduction of each part of the film substance, and these respective time values multiplied by the constant current give the corresponding quantities of electricity expended. Then each millicoulomb per square centimeter represents a film thickness of M X 108____ 2DX 96,494 X 103 where M is weight of oxide (or sulphide) giving one gram-atom of oxygen (or sulphur) for cathodic reduction, D is density of the oxide (or sulphide) and t is the thickness in Angstrom units per millicoulomb per square centimeter. The value of t for cuprous sulphide (cubical) is 14.27, and is obtained by substituting 5.78 for D and 159.20 for M in equation a. Previous values hf t for cuprous and cupric oxides (12.36 and 6.39, respectively) were used in the present work.

Jan 1, 1939

By J. B. Dyess, H. A. Miley

Tarnish films on some of the common metals (particularly on copper and silver) have been of much scientific and commercial concern for a long time, but before the development of the electrical method1 of measuring film thicknesses there was no satisfactory quantitative approach by which to study the separate parts of these complex films. This method has been adapted to the measurement of duplex (cuprous-cupric) oxide films on copper.2 In the present work it has been used to measure tarnish films on copper when they were mixtures of cuprous oxide and cuprous sulphide, and also when they contained cuprous oxide, cupric oxide and cuprous sulphide, each component part being measured at a different potential value. Oxide-coated copper specimens, prepared by heating copper in air at chosen temperatures for given periods, were exposed to moist hydrogen sulphide in air to forml the various oxide-sulphide films studied. The comparative resistances afforded by (I) different thicknesses of oxide films, and also (2) equal thicknesses of oxide and sulphide films, against severe attacks of hydrogen sulphide were measured. The electrical method requires that the time be observed for the cathodic reduction of each part of the film substance, and these respective time values multiplied by the constant current give the corresponding quantities of electricity expended. Then each millicoulomb per square centimeter represents a film thickness of M X 108____ 2DX 96,494 X 103 where M is weight of oxide (or sulphide) giving one gram-atom of oxygen (or sulphur) for cathodic reduction, D is density of the oxide (or sulphide) and t is the thickness in Angstrom units per millicoulomb per square centimeter. The value of t for cuprous sulphide (cubical) is 14.27, and is obtained by substituting 5.78 for D and 159.20 for M in equation a. Previous values hf t for cuprous and cupric oxides (12.36 and 6.39, respectively) were used in the present work.

Jan 1, 1939

By E. P. Pfleider

IT is generally believed that the amount of diamond drilling will increase appreciably in the next decade, as the search for minerals throughout the world becomes more difficult and intense. An attendant problem may be one of short diamond supply, resulting in higher bit and drilling cost. With this background, the U. S. Bureau of Mines1 and the School of Mines at the University of Minnesota2 have established comprehensive research programs in diamond drilling. One of the several aims is the design of a more efficient bit, which would lower diamond consumption and increase rate of advance, both essential in reducing drilling costs.

Jan 2, 1953

By Luis A. Fierino, M. Ashraf Mahtab

This paper reviews the background of, and solution techniques for, the major geomechanics problems affecting caving operations, including prediction of cavability, defining size distribution of or fragments, stability and support of production openings, and control of rock bursts and subsidence. Further research is also suggested in the solution of the various geomechanics problems.

Jan 1, 1984