Search Documents

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By Chase Palmer

INTRODUCTION. WHILE the reducing action of organic matter, of ferrous sulphate, and of hydrogen sulphide has frequently been invoked to account for the deposition of native gold and silver from ore-forming solutions, the high efficiency in this respect of certain of the metallic minerals which form the ore itself has not been sufficiently recognized. If a little finely powdered chalcocite is placed. in a test-tube and 2 or 3 cc. of a dilute solution of gold chloride are poured over it, two or three shakes of the tube suffice to remove all the gold from the solution. The color of the solution changes from yellow to pale green, showing that copper is dissolved simultaneously with the precipitation of metallic gold. If a piece of chalcocite is hung in a dilute aqueous solution of silver sulphate (1 normal), a coating of silver begins immediately to form on the mineral, and within a few moments a beautiful silver tree has developed, similar to that formed when metallic zinc is immersed in a similar solution.

Jan 5, 1913

By A. L. O’Neil, J. A. Wineland, A. B. Arnold

Movement of water through the Tehachapi Mountains was one of the most challenging parts of the planning, design, and construction of the California Aqueduct. The California Aqueduct is the main artery of the California State Water Project, which will move water 444 miles from the Sacramento-San Joaquin Delta into the arid and semiarid, densely populated parts of Southern California. The $2,000,000,000 project, designed and constructed by the California State Dept. of Water Resources, was started in 1957 at the Oroville Dam site and is now well past the halfway mark in construction. Water is now being delivered from the California Aqueduct to portions of the San Joaquin Valley. The California Aqueduct is scheduled for completion in 1972. Tunnels on the Tehachapi Crossing are often overshadowed in engineering descriptions of the Crossing by the tremendous importance and engineering significance of the Tehachapi pumping plant which will pump water through the tunnel system. For purposes of this paper, it will suffice to say that the plant is designed to lift 4100 cu ft of water per sec up approximately 2000 ft, making this the highest pumplift in the United States and one of the largest in the world. Water will be moved from the pumping plant through twin tunnels called the Tehachapi Discharge Lines to the top of the lift. From here, water will flow through four additional tunnels which are all linked by short connecting structures (Fig. 1). The tunnels are referred to as Tunnels 1, 2, 3, and Carley V. Porter Tunnel. HISTORY Selection of the final route of the Tehachapi Crossing was the result of comprehensive investigations beginning in 195 1. Numerous tunnel

Jan 1, 1970

By Akira Ishizu, Nobuo Matsui, Hideo Yamamoto, Tatsuya Nagahama

At Kamioka Mine of Mitsui Mining & Smelting Co., Ltd., Japan there are three mills, treating a total of 6400 t/d of lead-zinc Ore. In the lead-zinc bulk differential flotation at Shikama Mill the addition of reagents is automatically controlled by the feed rate, the lead and zinc content in feed, froth and tailing, the pH and the concentration of cyanide ion in the pulp. As the zinc thickener overflow at Shikama Mill contains CU(CN)3--, ZnS, CdS, CN-, xanthate and frother, all the ingredients in the over- flow other than CN are floated by using the Nagahm flotation machine, and the water containing only CN- is effectively recycled to the lead- zinc differential flotation circuit. In the lead-zinc straight differential flotation at Mozumi Mill, the overflow of tailing pond is recycled especially to the cleaning flotation circuit by decreasing the pulp density. Thus the integrated recycling of wastewater greatly reduces environmental problem and in addition, it generates sizeable profit.

Jan 1, 1977

By R. J. Schilthuis, T. V. Moore

In a previous paper,' the results of some experimental work on the measurement of slippage in the flow of oil and gas mixtures through vertical pipes were presented. The data obtained were correlated and equations were deduced from which the performance of the experimental gas-lift could be predicted with reasonable accuracy. However, attempts to apply the equations to the calculation of pressure drops in actual flowing wells yielded erroneous results. At the time the results of the experimental work were published, no satisfactory explanation could be offered for the failure of the empirical equations to express properly the performance of wells. However, recent work has led to the development of a new hypothesis which presupposes certain conditions affecting the flow of oil and gas in wells. When the proposed equations are corrected to allow for these conditions, an agreement between the observed and calculated performance of the actual wells is obtained which in most cases is quite satisfactory, although it is subject to certain limitations. In this paper, the method of calculating the pressure drop in actual wells is considered, and the application of the method to the design of tubing is discussed. (For nomenclature used in this discussion, see Table 1.) Factors Affecting Slippage and Efficiency At the outset, a few of the principle factors affecting slippage and efficiency in the gas-lift discussed in the previous paper will be reviewed. In the flow of the mixture of oil and gas in a vertical pipe, slippage is the phenomenon of gas moving upward with a. linear velocity greater than that of the oil. Under steady conditions, if given quantities of oil and gas enter the tubing per unit of time, the same quantities of oil and gas per unit time must, on the average, pass every section of the tubing; otherwise, there would be accumulation or depletion of the oil or gas at some sections, and the flow would be unsteady. Therefore, if the gas is to flow at a greater linear velocity than that of the liquid,

Jan 1, 1933

By E. C. Bitzer

THE primary object of the work described in the following pages was to simplify the equipment in the separating circuit of the heavy-media process by substituting a spiral classifier for the separatory cone. Mechanical considerations were the leading attraction and the best that was hoped for on metallurgical performance was that the new vessel would give results equal to those obtained by conventional equipment. Tests have demonstrated in commercial operation on iron ore that the mechanical advantages of the spiral separator are about as predicted; also, the metallurgical performance is superior to the cone on the ores treated. Treatment of iron ore involves the separation of two products: a concentrate that sinks and a float product that contains true float material plus a controlled division of interfering middling. The middling material is heavier than the average specific gravity of the separating medium. Recent work with the spiral separator on Tri-State zinc ore showed that the middling material had to be recovered as concentrate because this fraction contained the bulk of the-zinc in the ore. It has been demonstrated that it is possible to make three products with the new separator on an ore such as this: a float tailing, a float middling, and a high grade heavy sink product. It appears from this last work that the new separator has definite mechanica1 and metallurgical advantages over any type of separating cone for treating feed that contains large amounts of material of a specific gravity close to that of the separating medium. However, either type of separator should perform equally well, metallurgically, on feed that is free of middlings. Each series of experiments with the spiral separator as required additional work to fully develop the possibilities of the machine. For this reason the paper is divided into chronological parts. History of Development A drag-type classifier was first proposed as a substitute for the cone separator by Butler Brothers technicians during the initial tests with galena medium at Crosby, Minn., in 1937. The desire for finding a substitute for the cone arose from trouble with interfering middlings and certain operating disadvantages of the cone. The possibility of using a spiral classifier was also suggested at this time by Emmett Butler and C. J. Abrams. However, inability to satisfactorily recover fine galena, which was used as a medium, terminated all development work at Crosby. During the winter of 1937--1938 investigation started on magnetic medium with concurrent s development of the inverted or closed- top cone, which was found necessary to eliminate iron-ore middlings with the float product. About

Jan 1, 1947

By Otto Wartenweiler

AFTER the phenomenal development of the new mine, the United Eastern Mining Co., with Mr. Frank A. Keith as President, decided to install a reduction plant. The character of the ore, closely resembling the product of other mines in the district, did not offer any particular metallurgical problems, since these neighboring mines had been operating milling plants very successfully for several years. Thus, with the general metallurgical treatment fairly well-defined, the matter of next importance was to design and construct a plant as economically as possible, that would give the best results obtainable. The ore consists of a mixture of calcite and quartz in about equal quantities with some decomposed andesite, while the average value of mill heads were calculated to be $20 plus in gold, no silver being present. The tonnage to be treated at ,the start was fixed at 200 tons, but, in view of the favorable condition of the mine, it was considered advisable to arrange facilities, for increasing the capacity to 400 tons. . While it is best in some cases to adopt a distinct independent unit system where future enlargement is contemplated, in this instance the plans worked out differently. Summarized, the treatment adopted consists of coarse crushing, coarse grinding, fine grinding and cyanidation. For coarse crushing the selection of the No. 6 size gyratory crusher was governed not so much by its capacity as by the size of the feed openings to properly receive the run-of-mine material, which was too coarse for a No. 5 crusher. To accomplish the coarse grinding to. best advantage, a careful comparison was made between the modern steel ball mill-the last word in crushing and grinding-and one of its older, and, at that time better-established, competitors, the rolls.' The following conclusion was reached: While it is possible that for the sized plant under consideration the cost of operating rolls might be a little cheaper, it is preferable to use ball mills because a simpler arrangement is possible, and1 because. the handling of, ball mills is preferred by the operator.

Jan 11, 1917

By H. A. Kortmann, K. Koch, B. M. Grover, O. P. Burghardt

Addition of lime, especially when treating a hematite feed, sometimes results in swelling and a severe loss in strength during reduction in the temperature range 900° to 1100°C and in grain disintegration in the temperature range 400° to 600°C in a weakly reducing atmosphere. Swelling and/or grain disintegration of pellets is often the reason for trouble in blast furnace operation, resulting in a decrease in the rate of smelting. Following a brief description of the test procedures employed (measurements of swelling, pressure-reduction-softening and grain disintegration), some results are given which were arrived at when testing pellets from industrial plants. Results of systematic tests are presented, where the effect of the quantity and quality of the gangue upon the behavior during reduction of pellets is illustrated. Varying amounts of quartz and limestone were added to a high-grade hematite ore and, then, pellets produced in a pot grate. The relationships of the behavior of the fired pellets during reduction are presented, among others, in the ternary system CaO-FeOn-SiOP. Finally, an attempt is made to explain the reasons for swelling, loss in strength, and grain disintegration.

Jan 1, 1974

[ ]

Jan 1, 1938

By William A. West

One manifestation of anelastic properties in solids is the mechanical elastic aftereffect, which may be described briefly as follows: If a stress is applied to a solid body, a deformation or strain is produced. On removal of the stress, this deformation disappears, at least in part. As a first approximation, this appearance or disappearance of deformation usually has been considered instantaneous. Actually, however, for a very wide variety of substances, on application of stress the instantaneous deformation is followed by a further slow yielding, which continues, although at a rapidly diminishing rate, for as long as the stress is applied. Similarly, on removal of the stress, the instantaneous recovery from deformation is followed by a further slow recovery, which continues, although at a rapidly diminishing rate, often for a long time. This latter phenomenon has been called the "elastic after-effect." Experiments upon the elastic after-effect in metals, when properly designed and when properly interpreted, are capable of giving quite precise information regarding the relation between stress and strain in the various constituent parts of the metal. For example, if certain parts of the metal, such as grain boundaries or slip bands, behave in a viscous manner—that is, if therein—the relaxation spectrum will contain lines or bands associated with the relaxation of shear stress within these parts. No attempts have heretofore been made to utilize elastic after-effects for obtaining such detailed information. The purpose of the present paper is to explore the possibilities of properly designed and interpreted experiments on the elastic aftereffect in metals. Since new procedures and principles are employed in this study, an attempt has been made to record each step taken. Elastic after-effect observations are susceptible of simple interpretation only when the stress level employed is so low that all effects are linear with the stress. Just how low the stress level must be can he determined only by experiment. An advnntage, other than simple interpretation, is associated with low stress levels. When all effects are linear, derived quantities, such as the relaxation spectrum, are independent of the stress distribution. It is, furthermore, possible to employ the type of deformation that is most convenient from the experimental standpoint; for example torsion. It appears that in experiments involving both loading and unloading the following would be observed: I. Instantaneous deformation, recoverable instantaneously in whole, or in part. 2. Delayed deformation, recoverable slowly in whole, in part, or not at all. 3. Permanent deformation, the difference between total deformation and total recovery. In the work here described, unloading experiments only were made. Wires were

Jan 1, 1947

By William A. West

One manifestation of anelastic properties in solids is the mechanical elastic aftereffect, which may be described briefly as follows: If a stress is applied to a solid body, a deformation or strain is produced. On removal of the stress, this deformation disappears, at least in part. As a first approximation, this appearance or disappearance of deformation usually has been considered instantaneous. Actually, however, for a very wide variety of substances, on application of stress the instantaneous deformation is followed by a further slow yielding, which continues, although at a rapidly diminishing rate, for as long as the stress is applied. Similarly, on removal of the stress, the instantaneous recovery from deformation is followed by a further slow recovery, which continues, although at a rapidly diminishing rate, often for a long time. This latter phenomenon has been called the "elastic after-effect." Experiments upon the elastic after-effect in metals, when properly designed and when properly interpreted, are capable of giving quite precise information regarding the relation between stress and strain in the various constituent parts of the metal. For example, if certain parts of the metal, such as grain boundaries or slip bands, behave in a viscous manner—that is, if therein—the relaxation spectrum will contain lines or bands associated with the relaxation of shear stress within these parts. No attempts have heretofore been made to utilize elastic after-effects for obtaining such detailed information. The purpose of the present paper is to explore the possibilities of properly designed and interpreted experiments on the elastic aftereffect in metals. Since new procedures and principles are employed in this study, an attempt has been made to record each step taken. Elastic after-effect observations are susceptible of simple interpretation only when the stress level employed is so low that all effects are linear with the stress. Just how low the stress level must be can he determined only by experiment. An advnntage, other than simple interpretation, is associated with low stress levels. When all effects are linear, derived quantities, such as the relaxation spectrum, are independent of the stress distribution. It is, furthermore, possible to employ the type of deformation that is most convenient from the experimental standpoint; for example torsion. It appears that in experiments involving both loading and unloading the following would be observed: I. Instantaneous deformation, recoverable instantaneously in whole, or in part. 2. Delayed deformation, recoverable slowly in whole, in part, or not at all. 3. Permanent deformation, the difference between total deformation and total recovery. In the work here described, unloading experiments only were made. Wires were

Jan 1, 1947

By Robert I. Jaffee, Walter L. Finlay

IN the broad survey of the nonferrous' metallic elements contained in this book, the reader may well be impressed by the wide range of property combinations offered by the many metals and alloys the metallurgist has prepared since before Kubla Khan. The diversity is great and the overlap is considerable. It is particularly surprising, then, to find the latest structural metal new- comer designated by such extravagant terms as "Cinderella Metal," "Wonder Metal," "Miracle Metal," "The Metal of Tomorrow," "Dream Metal or Nightmare?" and "The Middleweight Champion of the Structural Metals." Of these and others, the most appropriate designation for the metal involved, titanium, appears to be that of The Middleweight Champion. Its intermediate density of 4.5 and elastic modulus of 16 million is a unique combination between the lower density and modulus of magnesium and aluminum and the higher density and modulus of copper, nickel, and iron. It is light, strong, ductile, and corrosion resistant. A chemical neighbor in group IV of the Periodic Table, zirconium, is similar to titanium in many respects but is appreciably denser, 6.5 instead of 4.5, less stiff and relatively much less abundant. On the other hand, the resistance of zirconium to acids and alkalies is better than that of titanium. Also, compensating for its higher density, lower stiffness, and somewhat lower strength level compared with titanium, zirconium has much better permeability to slow neutrons and is much more suitable as a material of construction for nuclear reactors.

Jan 1, 1953

By Carl H. Samans

THE INFORMATION AVAILABLE on the rolling characteristics of the precious metals-gold, silver, the platinum metals and their alloys-is incomplete and mostly from scattered sources. In the present paper an effort has been made to assemble and correlate it and to fill in some of the gaps that exist. GENERAL ROLLING CHARACTERISTICS SOME EFFECTS OF IMPURITIES Gold and its alloys are generally considered to be hot short and hence are usually rolled cold. Cold rolling of the yellow, green, and pink gold alloys. Which customarily contain gold, silver, copper and zinc and frequently some nickel as well, introduces no new problems since reasonable reductions are quite feasible and the alloys show little tendency to fire crack in subsequent annealing. The white gold alloys. which usually contain little or no silver and 10 pct or more nickel, are very susceptible to fire cracking1 and hence wrist he given relatively heavy reductions, i. e., 8-10 pct or more per pass with a total reduction of about 50 pct between anneals, to minimize this tendency. In addition, it is preferable to keep the bar as flat as possible during rolling. Although no comprehensive study appears to have been made of the effects of impurities on the cold rolling characteristics of gold alloys, the observations of Nowack2 on the effects of small

Jan 1, 1948

By C. G. Dunn, K. T. Aust

SEVERAL studies1-10 have reported a type of grain boundary migration which occurs when a strained grain grows into an adjacent deformed grain during annealing. Beck and Sperry called this phenomenon strain-induced grain boundary migration, since the observed boundary movement, which takes place in a direction away from the center of curvature, is apparently motivated by the excess free energy of strain hardening. However, little information has been obtained on the detailed structural changes accompanying such grain boundary motion. The problem of driving force for strain-induced boundary migration was considered by Dunn and Daniels,' who used bent bicrystals of Si-Fe. They demonstrated that two grains of differing energy, in the form of subboundaries, behaved according to the concept that the low-energy grain would grow at the expense of the high-energy grain. Beck" reported experiments of Sperry for high-purity aluminum, which indicated that generally the particular grain of a pair which work-hardened more was invaded. The measure of work hardening here was

Jan 1, 1958

By R. J. Piros, Brusenback, D. A. Dahlstrom

DEWATERING fine coal has been a serious problem to many operators who desired to wet-wash finer sizes and maintain high recovery. Centrifugal driers have become popular for this purpose for sizes between 3/8 in. and 14 mesh. Below 14 mesh the perforated screen centrifuges lose a large per- cent in the effluent solid bowl types that do retain -14 mesh coal, produce excessive degradation, tend to retain the highest ash fraction in any size fraction, and are subject to abrasion, which results in higher maintenance. In 1949 Truax-Traer Coal Co. planned a cyclone installation at their Ceredo preparation plant to recover coal down to 150 mesh with approximately a 14-mesh top size. Since available centrifugal equipment was not considered satisfactory, an investigation of rotary vacuum filters was begun in cooperation with the Peterson Filters and Engineering Co. to determine the suitability of the Peterson Top Feed Reservoir (TFR) filter. This investigation, which is described below, has resulted in a highly satisfactory installation of two 6x10-in. Peterson TFR filters that have been in operation over a year. After some preliminary laboratory batch vacuum filter tests, a pilot plant double-drum Peterson TFR filter was installed at Ceredo to prove the feasibility of vacuum filtration and determine optimum conditions. The full scale units were then installed on the basis of the pilot plant results. This was followed by an extensive research program on vacuum filtration in the laboratory at Northwestern University to investigate basic design and operating variables and their influence on final moisture con- tent of the filter cake. A method of scale-up from laboratory batch tests to the full-size unit was also proposed and proved. Because of the importance of dewatering fine coal today, it was felt that the results of the three steps should be made available for the use of others facing this problem. The work at Northwestern is given in a theoretical section following the discussion of the pilot plant and full- scale operation. Fig. 1 is a flow diagram of the cyclone and filter installation. The feed is drawn from below the

Jan 1, 1952

By W. D. Felix, R. D. Smith, J. A. Campbell

The mechanism most consistent with available information on atmospheric trace element emissions involves the volatilization of a significant fraction of many trace elements during coal combustion, with subsequent condensation on fly ash as the combustion gases cool. The larger surface-td-volume ratio of the smaller particles leads to an enrichment of the volatile trace elements. From an environmental viewpoint, the submicron size particles are of greatest concern. These particles show the highest concentrations of trace elements, are least efficiently collected by pollution control devices, have high atmospheric mobilities, and are deposited preferentially in the pulmonary and bronchial regions of the respiratory system. The mechanisms for trace element enrichment and formation of submicron particles will be described.

Jan 1, 1981

By Carl Floe

A NUMBER of proposals have been made for the hydrometallurgical recovery of copper from flotation concentrates, but as yet no process has been developed that has demonstrated an ability to compete with the present smelting methods under ordinary conditions. The treat-ment of copper concentrates by hydrometallurgical methods is in general similar to that used in the present electrolytic zinc process and involves roasting, leaching with H2S04 solution, separation of solutions, control of impurities and electrodeposition. While many of these steps are simpler and more readily carried out for copper than for zinc, a number of inherent difficulties have prevented the general adoption of the process. To compete with smelting, the following problems must still be con-fronted, although many solutions for their have been proposed: (1) con-duction of the roast in such a way that leaching will give an extraction of copper comparable to that obtained by smelting; (2) regulation of the ferric iron content of the solutions during electrolysis; (3) disposal of the excess acid regenerated from the sulphates formed in roasting; (4) eco-nomical recovery of the precious metals from the leach residues. The roasting problem is largely one of preventing the formation of copper ferrites, CuO.Fe2O, and Cu20.Fe2O3, which are quite insoluble in dilute sulphuric acid. These ferrites are apparently formed' to a small extent even at low temperatures and above 650° C. their formation is rapid1. While it is possible to carry out laboratory roasts in such a way that less than 5 per cent of the total copper is present in the insoluble ferrite form, a closer temperature control is required than can readily be obtained in industrial furnaces. The flash" roasting effects and consequent high temperatures that occur as the calcine falls from hearth to hearth in the ordinary multiple-hearth roaster are probably largely responsible for the inevitable formation of some ferrites. The result is that in a commercial plant the extraction of copper would not average more than 90 per cent in a single 10 per cent H2SO4 leach. This is

Jan 1, 1937

By Charles A. Ashburner

[The statistics contained in this paper were collected for the United States Geological Survey and communicated to the Institute, by permission, prior to their publication in the report on the Mineral Statistics of the United States for 1887.1 The total coal-production of Alabama in 1887 was about 1,950,000 short tons, the spot-value of which, at the mines, was $2,535,000. The coal-regions of the State lie in the extreme southern part of the Appalachian coal-field, the northern part of which lies along the western New York-Pennsylvania State line; between these limits, New York on the north and Alabama on the south, portions of the

Jan 1, 1889

By W. J. Keep

We have found that our graphic representations were, in some cases, not perfectly understood. In the tables by which we illustrate all our tests, the records appearing in the vertical columns between the rulings are the results of the tests of iron having the percentages and characteristics noted at the top of the column. The record is made by a short horizontal line in such vertical columns. It is located in horizontal spaces, which divide the table into units of measure, to indicate the value of the record. For example, in the upper part of Table VII. is recorded the transverse strength of the series of tests with white iron and aluminum, which were reported in our former paper. The numbers at the extreme top are the test-numbers. The fractional numbers below are the percentages

Jan 1, 1890