Search Documents

By R. N. Powell

The Pipeline ore body was discovered in March 1991. The construction of the new mine and mill did not start until early March of 1996. Upon completion of permitting and corporate project approval, the 289 million USD project was “fast tracked”. The commissioning began 11 months after start of construction and the project ended 40 million USD under the budget figure. The objective of this paper is to review and highlight the Pipeline Project history from discovery, design, lawsuits, permitting, and re-design through to current - 1998operating practices. Particular emphasis will review the process design, design mistakes, and design successes. The paper will review project history, feasibility, design concepts, operator training, construction, financial and the current operation. Additional discussion will review what design features worked and which did not work within the process plant.

Jan 1, 1999

By R. J. Wasilewski

The resistivity of single crystal and of polycrystalline metal has been determined between 77° and 1500°K. At comparable purity, the resistivity of the poly crystalline metal differs from that calculated from the axial resistivity values. The observed anisotropy is briefly discussed. A zone refined titanium rod was obtained from F. J. Darnell.1 The hardness of this material varied between 52 and 64 Bhn, indicative of its high purity. Single-crystal specimens were cut out from a few large grains, elongated predominantly along <1120>. Resistance measurements were taken with specimens immersed in liquid nitrogen, solid CO,, and acetone, and at ice point, and then recorded continuously between room temperature and 1200" to 1250°C, throughout at least one full heating and cooling cycle at a rate of l° to 3°C per min. Four probe measurements were taken using spot-welded Pt wire 0.003 in. in diam as potential terminals, and the electromotive force drop was determined poten-tiometrically. A standard resistance, in series with the specimen, served to determine the dc current (generally about 80 ma) in the circuit. In order to eliminate spurious thermal electromotive forces, the circuit polarity was automatically reversed at 5-min intervals, and the mean of the two adjacent readings taken as the true electromotive force value. The discrepancy between the readings at reversed polarities was generally of the order of a few µ v, as all the spot-welded joints were contained within a volume of some 5 mm cube. The relative resistance (R T/R 273o) variation with temperature is tabulated below, and shown in Fig. 1, as measured during the first heating run. The discontinuous drop in resistance, corresponding to the a — ß transformation, started for both initial orientations at 1170°K; i.e., some 15°K above the accepted value of 882°C (1155°K). Judging by the temperature ranse of transformation—some 30°K for the single crystal and 20°K for the polycrystal-line specimen—this difference is believed caused by the solution of the oxygen present initially on the surface of the specimens. The general trend of the resistance vs temperature shown in Fi,;. 1 is in qualitative agreement with that previously reported for polycrystalline titanium metal. 2,3 Significant anisotropy is, however, indicated by the crossing over of the curves for <1120> and <0001> orientations at 273°, 650°, and 1000°K. This difference is most startlingly shown in Fig. 2, where instantaneous temperature coefficients (l/R273 x dR /dT) are plotted for both the first heat-

Jan 1, 1962

By J. F. Reddick

The South African coal mining industry is currently disposing of about 10 million tons of ultra-fine coal (<150 µm) per year. Once discarded, these sulphur-containing ultra-fines contribute to several environmental problems. As part of a project initiated by the Water Research Commission to investigate the use of Cleaner Production (CP) in the mining industry, a study was carried out to determine whether a CP approach could be used to identify opportunities to reduce this coal waste, and to determine which of these opportunities would be most feasible. In order to do this, a CP assessment was conducted at three case study collieries in the South African Witbank coalfield. Mass-balancing and sampling, followed by laboratory characterisation tests and site surveys, were used to determine the quantity, quality and sources of the ultra-fine coal at the three collieries. Literature reviews, brainstorming sessions and interviews then followed to generate the CP options. An environ-mental, economic and technical feasibility assessment was then prepared for each option, to determine the most viable interventions for implementation. A number of opportunities were identified through the assessment. By preventing coarser coal from being discarded with the ultra-fine coal, the quantity of coal disposed of could be decreased at all three collieries, and by up to 24% in one case. Increasing the crusher top size would reduce the amount of coal that is milled to less than 150 µm, so that less is wasted. The ultra-fines that have already been disposed of on slurry dams can be completely reclaimed and converted into a valuable product, which can be sold as power station feedstock. The newly processed ultra-fines could be beneficiated using flotation and exported together with the coarser coal. The results of the assessments thus suggested that workable CP opportunities to reduce ultra-fine coal wastage exist at the sites investigated, and that their feasibility is colliery-specific. The associated financial benefits of the proposed options suggested that CP is a realistic approach to addressing environmental problems. Keywords: Cleaner Production; coal mining; coal-washing; ultra-fines

Jan 1, 2007

By H. K. Lin

Deepwater discharges of sulfide flotation tailings have been practiced for several decades. Oxygen penetration and organic matter content in such environments are the two major factors that determine their reduction-oxidation condition and hence the rate of sulfide mineral dissolution under such discharge environments. In this study, the effects of solution redox potential and pH on the dissolution of some heavy metals from sulfide flotation tailings were examined. Zn, Pb and Cu concentrations in solution were all higher at a higher redox potential and lower pH. Dissolved Zn concentrations reached 100 ppm even at a low redox potential of 105 mV and near neutral pH after 33 days. Pb concentrations were below 2 ppm at 105 mV and near neutral pH after 165 days. At 105 mV, the Cu concentrations were below 0.2 ppm at near neutral pH after 165 days. At pH 2.3, the Fe concentrations were higher at 420 mV than at 105 mV. But at pH 6.8, the Fe concentrations were lower at 420 mV than at 105 mV, due to the oxidation of Fe2+ to Fe3+ and the subsequent precipitation of ferric hydroxide. Arsenic concentrations in solution were all less than 0.002 ppm. For Zn, Cu and Fe, no significant differences were observed between the tests in solutions prepared using seawater and those using distilled water. However, Pb concentrations reached higher levels in solutions prepared using seawater.

Jan 1, 2009

By D. S. Bird

The Kennecott Utah Copper Modernization Project, initiated in 1986, was directed to provide an expansion and modernization of mining and process facilities at the property&apos;s Bingham Canyon Mine and ore concentrators. Major components in the project included installation of an in-pit ore crusher, transfer conveying system, and construction of a new copper ore concentrator with a design capacity basis of 70,000 tonnes/day. The Copperton Concentrator was commissioned in February 1988. A principal feature of the plant is the grinding circuit, comprised of three identical lines, each consisting of a 10.37 m (diameter) by 4.57 m (length) Semi-Autogenous Grinding (SAG) mill and two 5.54 m (diameter) by 8.62 m (length) ball mills. The SAG mills are driven by two variable-speed 9,000 kW DC motors coupled through a clutch-pinion gear-ring gear assembly. The ball mills are driven by 4,125 kW synchronous motors coupled through a typical clutch-pinion gear-ring gear system. The expansion and particularly the Copperton Concentrator performance was so successful that by early 1989, management began examining options to further expand production capacity. With regards to the concentrator, numerous alternatives were considered, ranging from installation of a grinding line similar to one of the existing lines, to a "super" line consisting of a 12.8 meter (diameter) SAG mill and a 20,000 kW motor with a capacity of 50,000 tonnes per day. The technical and economic analysis of the various scenarios indicated that one "large" 11.0 meter (diameter) by 4.88 meter (length) SAG mill with a production capacity of 32,000 tonnes per day and a 12,000 kW drive would be optimum. The key question to be answered in the project was whether to continue with the pinion-ring gear combination, or install a gearless drive. The following paper outlines many of the items that were evaluated in the mill selection process followed by actual plant performance, and a discussion of ongoing plant continuous improvement projects.

Jan 1, 1995

By M. A. Trevits

The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate, improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Since wood is the second most abundant fuel available during a coal mine fire, it was decided that series of large-scale wood crib fire tests were needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.

Jan 1, 2009

Strategic Branding ? In 2006 Explore for More was created ? By industry, for industry ? Cohesive approach to career attraction ? Defines industry and employers of choice Career Kits ? Positive impression of mining: ? before seeing the brochure 31% ? after seeing the brochure 83% ? Likely to consider a career in mining: ? before seeing the brochure 12% ? after seeing the brochure 23% MARS ? Mining Attraction, Recruitment, and Retention Strategy (2007-2010) ? Attract, recruit and retain a skilled workforce ? Increase participation of under-represented groups ? Dispel myths and misconceptions of the mining industry ? Inform and educate Canadians of career opportunities ? Promote and build upon industry best practices in workforce planning

May 1, 2009

By A. Rosen, P. Wynblatt, J. E. Dorn

The temperature, strain rate, and structure dependence of the flow stress in a poly crystalline Fe-2 pct Mn alloy was investigated between 77" and 370°K. It was possible to identify the low-temperature data from 77° to 160°K with Dorn and Rajnak&apos;s theory of the Peierls mechanism of plastic deformation. Above 160°K one or more thermally activated mechanisms must he operative; however, these were not identified in this investigation. The mechanistic basis for the rapid decrease in the flow stress of bcc metals with an increase in temperature over the low-temperature range is yet being debated. Various dislocation mechanisms have been suggested in the past but the agreement between the various proposed theories and the experimental results have not been definitive. In the present paper, the authors will demonstrate that the plastic behavior of polycrystalline iron containing 2 wt pct Mn plus interstitials agrees excellently with predictions based on the Peierls mechanism from 77" to 160°K whereas from 160" to about 370°K other as yet unidentified thermally activated mechanisms take over. Undoubtedly, the overlap of these mechanisms with the Peierls mechanism contributed to the difficulties of rationalizing the low-temperature behavior of iron and its alloys. I) EXPERIMENTAL TECHNIQUES AND RESULTS Although extensive data are now available on the effect of temperature and strain rate on the flow stress of various bcc metals and alloys, it was, nevertheless, deemed necessary for the objectives of the present study to obtain highly accurate data of the type most pertinent for checking the theories on a series of well-documented work-hardened states. Iron containing 2 wt pct Mn was used in this investigation in order to obtain a lower ductile to brittle transition temperature than that for iron.&apos; The additional elements present were 0.004 pct C, 0.05 pct 0, 0.004 pct S, 0.003 pct P, 0.006 pct N, and 0.001 pct Si. The as-received 3/8 by 3/4 in. bars were cold-rolled to 0.100-in. thickness, recrystallized under argon for 30 min at 1073"~, further cold-rolled to 0.063-in. thickness, and finally recrystallized under argon for 30 min at 1000°K. This treatment gave a stable reproducible equiaxed grain structure having an average grain diameter of about 90 p. Prior to the final recrystallization treatment, the sheet was machined into tensile specimens 1/4 in. wide having a 1.625-in.-long gage section. All specimens were tested in controlled-temperature baths on an Instron Testing Machine. For convenience in the theoretical analyses the data will be given in terms of the shear stress for flow, 7, the shear strain rate, f, and the shear strain, y. A series of three standard strain-hardened states were obtained by prestraining specimens at 300°K and at a shear strain rate of 7.68 x lo-&apos; per sec to three stress levels of 6.89 X l08, 10.3 X lo8, and 14.5 x 10&apos; dynes per sq cm, respectively. Immediately following this prestrain the temperature bath was changed and each specimen was pulled in tension at either f = 7.68 X lo-&apos; or f = 3.06 X 10"3 per sec. In terms of the accuracy that was achieved, the values obtained did not deviate more than *0.1 X 10&apos; dynes per sq cm and * 1°K from the reported values of stress and temperature and not more than *5 pct in the reported values of the strain rate. The tensile stresses were converted to shear stresses using a factor of 1/2. The shear stress for the initiation of flow at the test temperature was determined by taking a y = 6.16 x 10&apos;3 offset. from the modulus line at which point good accuracy could be achieved in determining y and the associated flow stress 7, with only a negligible increase in the pre-

Jan 1, 1965

Much of the coal and gold mining industry of New Zealand is small scale. Funding is tight and mechanisation limited. The country has many well documented small coalfields (some with significant outcropping) and alluvial gold deposits. These are generally remote, difficult to access (physically and otherwise) and of submarginal value (largely a consequence of size when viewed for extraction by traditional techniques). The industry is also burdened by environmental and bureaucratic constraints. The above over simplified setting suggests to the Author, a newcomer to New Zealand, the opportunity to consider some novel concepts based on technology and techniques developed overseas or borrowed from other industry sectors. The objective being to make viable in economic and environmental terms projects that might otherwise be stillborn if considered for exploitation by conventional means. The paper mainly discusses 2 concepts focusing on the application of augers for exposed high wall or outcrop coal and micro-tunnelling augers for alluvial gold extraction. These may be considered high mobility &apos;container&apos; (as in shipping container) packaged, or &apos;non invasive&apos; mining systems. It is stressed that these are but concepts and have yet to be subjected to rigorous financial or engineering scrutiny. This could only follow their acceptance by, and input from, New Zealand miners. There will also be brief mention of a new modular conveyor system which might have application within the concepts or existing small scale mineral extraction operations and mention of a project currently in progress to apply tangible &apos;sustainability&apos; to underground coal mining.

Jan 1, 1996

Lead isotope measurements indicate that lead from the A.B.H. Consols mine and two transgressive veins in Browne&apos;s shaft is &quot;Thackaringa&quot; type and not &quot;Broken Hill&quot; type.

Jan 1, 1970

By Paul Weir

BLEACHING clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller&apos;s earths fall within the general group of bleaching clays and gradually the commercial term "fuller&apos;s earth" has been applied to natural clays originating, for the most part, in the south-eastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States.1 Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). TABLE 1.-Physical and Chemical Composition of Different Types of Clays Composition, Per Cent Constituents and Properties Bentonite Fuller&apos;s Mud Clay (Wyoming) Earth (P Peak)&apos; (Alluvial) Silica (SiO2) 60.0 69.6 61.67 Alumina (Al203) 19.0 14.3 20.34 Ferric oxide (Fe203) 2.8 3.90 7.70 Titanium oxide (Ti02) 0.13 0.70 1.01 Lime (CaO) 0.5 0.80 0.00 Magnesia (MgO) 2.0 1.00 0.24 Soda (Na2O) 2.4 0.40 0.31 Ignition loss 4.7 6.77 8.51 Moisture content 8.0 10.0 20.0 Isoelectric point, pH 9.2 9.2 6.5 Average swelling volume 15.0 0.0 0.0 Weight per cubic foot, lb 55.0 40.0 65.0 Material passing 200-mesh sieve, per cent 90.0 85.0 50.0

Jan 1, 1939

By Peter Florian

At 5:50 am on October 1, 1992, the new $800 million Pittsburgh International Airport Midfield Terminal opened its gates to the world after five years of construction and more than 24 years of planning. Despite numerous design changes, this massive project was completed on time and substantially within budget. The importance of this airport to Allegheny County and the Pittsburgh region was recognized 24 years earlier by Allegheny County Commissioners Tom Foerster and the late Leonard Staisey. Staisey and Foerster established a program to acquire land for the "Airport of the Future".

Jan 1, 1993

By Vedala Sastry

Longwall mining for coal extraction in deeper deposits is gaining momentum in India, due to the increasing stripping ratios and depletion of shallow deposits amenable for surface mining. In longwall mining, presence of multiple seams with varying interburden thickness is a major problem especially while planning for over-mining. An investigation program was taken up to analyze the effect of the presence of goaf and virgin coal blocks in already developed and extracted lower seam by bord and pillar mining, on the stress distribution in the longwall panel in upper seam. Studies revealed marginal increase in horizontal and shear stress as longwall face passes above goaf to the virgin area present in lower seam. Stress distribution over chock shields was considerably affected when the face in upper seam reached 15-25m zone above the galleries in the lower seam. A clear influence of the presence of solid coal, galleries and goaf in lower seam was found in the loading of longwall panel in upper seam.

Jan 1, 2007

By Romano J. Micciche

One of the largest scale uses of a multiple, high-strength steel bar tiedown system is described. Tiedowns were installed to resist hydrostatic uplift forces acting on a section of the Interstate Highway Route I-90 southern approach roadway to the Third Harbor Tunnel, in Boston, Massachusetts. Site specific information is discussed regarding design, testing, and installation of Tiedowns. Conclusions are presented regarding the overall performance of this system and the application of this type of tiedown system on future projects.

Jan 1, 1994

By B. C. Slocombe

A large derelict inner city site was regenerated for use as a distribution warehouse. Difficult topography and soils conditions required the adoption of a combination of specialist geotechnical processes. Particular attention was paid to the preparation of the site, programming and capabilities of each technique as additional soils information became available.

Jan 1, 1989

By Jean-Pierre Hamelin

Ground movements induced by underground excavation are always of critical concern, particularly in urban areas. Compensation grouting now appears as a safe means to control these movements. The paper presents new advanced systems developed by the specialist contractor to bring, at all stages of the project, an efficient control of operations and presents a case history taken from the project at Tren Urbano, Rio Piedras Section, constructed beneath an historic commercial section of San Juan de Puerto Rico.

Jan 1, 2000

The following is a &apos;partial list of members and guests who called at Institute headquarters during the period Oct. 10, 1917, to Nov. 10, 1917. Edwin T. Blake, Berkeley, Cal. Alfred C. Lane, Tufts College, Mass. H. M. Boylston, Cambridge, Mass. W. G. Matteson, Houston, Texas. W. B. Cogswell, Syracuse, N. Y. E. Francis M&apos;Crossin, Birmingham, Ala. Paul R. Cook, Zaruma, Ecuador. R. E. Murray, Butte, Mont. F. W. DeWolf, Washington, D. C. Edmund Newton, Minneapolis, Minn. A. Faison Dixon, Venezuela. J. J. Ormsbee, El Paso, Texas. W. H. Dufur,, Oil City, Pa. Pablo Ortega, Havana, Cuba. Maxwell E. Erdofy, Lieut. Engr. Officers&apos;. W. E. Pomeroy, El Paso, Texas Reserve Corps, New York. J. C. Ralston, Spokane, Wash. Evan Fraser-Campbell, Scotland. W. L. Remick, Chrome, N. J. David B. Gemmill, Crown King, Ariz. Howard D. Smith, San Francisco, Cal. F. Lynwood Garrison, Philadelphia, Pa. Harold C. E. Spence, Steeple Rock, N. M. C. J. Hall, Spassky, Siberia. R. K. Stockwell, Salt Lake City, Utah. H. Hamada, Tokyo, Japan. Maurice W. Summerhayes, Timmins, Rush M. Hess, Bouse, Ariz. Ont., Canada. A. Howard Higgin, London, England Malcolm M. Thompson, Morsemere; N. J. A. O. Ihlseng, Joplin, Mo. Nicholas Truschkoff, Petrograd, Russia. T. Ishikawa, Japan. H. J. Wendler, Los Angeles, Cal. C. H. James, Tucson, Ariz. Ira T. Wright, Hurley, N. M. R. R. Landon, Philippine Islands. C. Yabe, Japan. Robert W. Bissell has now become associated with Gunn, Richards & Co., of New York, N. Y. Major Reginald W. Brock is giving a course in a school for commanding officers in England.

Jan 12, 1917

Commercialisation of Ni Heap Leaching at Murrin Murrin Operations

Sep 13, 2010

By J. Hartikainen

Kemi cardboard mill is founded on the alluvial bed of Kemi river at the north-eastern cost of Botnic Culf in Northern Finland. The alluvium consists of sandy and silty layers underlain by thick medium dense silty moraine layer. The first cardboard machine, having a belt width of 7,4 m, was constructed in 1972 on 7,5 to 9,5 m long wedge-shaped precast driven piles. Because of the excessive differential settlements and sometimes unexpected dynamic malfunctioning of the machine it was decided to strengthen the foundation before installing the partly new machine and increasing the running speed from 500 to 750 m/min. Piling was done under extremly strick limitations concerning space, vibrations, settlements, dust etc. Extra vertical support was made by using 23...25 long x-form steel piles driven by compressed air pile hammer down to rock. The piles were held together with old piles by a conctrete frame with diagonals, which made the total system - machine - foundation frame, piles and ground - ridgid enough to avoid resonance during dynamic loading.

Jan 1, 2010

By Geoffrey Fosbrook, Donald Phillips, Anil Parikh

The Second Avenue Subway is a $16.8 billion project planned by the Metropolitan Transportation Authority (MTA) in New York City. It will reduce overcrowding and delays on the Lexington Avenue Line, improving travel for both city and suburban commuters, and improving access to mass transit for residents of the East Side of Manhattan. The project is a new, two-track, 13.5 km (8.5 mile) subway extending from Lexington Avenue at 125th Street in Harlem on the north end of Manhattan, to Water Street at Hanover Square in Lower Manhattan. The first phase of construction includes rock tunnels from 92nd Street to 62nd Street and connection to the existing 63rd Street station, three new stations, and track and systems from 105th Street to 63rd Street, allowing service between 96th Street and Brooklyn via an existing Broadway Line. The following describes the Project in detail, discusses the construction challenges addressed in the design, and the initial design/build contract to be awarded in 2005. A discussion of the planned mined construction of two rock caverns and a cut-and-cover station construction are also included.

Jan 1, 2005