Search Documents

By Z. Duan

A novel concept involving the deployment of chemical stabilization has the potential to eliminate the need of slurry impoundments and significantly reduce the release of trace elements from the high surface area fine coal waste. The process involves mixing the fine waste generated from the underflow of a thickener operation with chemical stabilization agents to tie up the water and to create a solid waste material that can be discharged directly. Portland cement, sodium silicate, F type flyash, C type flyash and hydraulic lime were evaluated as stabilizing agents. A detailed experimental study has been conducted to identify the conditions that provide the maximum compressive strength within a short curing time. Results to date show the ability to achieve compressive strengths adequate for equipment to maneuver on using a Portland cement concentration of around 10% by weight. Quick-setting concrete was not found to enhance stabilization time and compressive strength.

Jan 1, 2012

By David H. Tang

Massive pillar failures were observed at two underground coal mines. The results of stability analysis using traditional pillar design formulae did not agree with the underground observations. Finite element models were used to analyze the causes and mechanisms of the pillar failures. The results were confirmed by the underground observations. Finally, the improved mine plan for each case was derived to ensure the stability of the underground structure.

Jan 1, 1990

By D Craw

Uplift of the antiformal ranges in Central Otago, New Zealand , has resulted in the progressive evolution of eluvial placer deposits in tectonic sediments on the range flanks and along their margins. The placers are derived from the reworking of fine-grained gold from the auriferous Manuherikia Group fluvial sediments which covered the basement prior to uplift of the ranges. Gold in the tectonic sediments at Matakanui shows a progressive increase in grainsize in successively younger sediments and nuggets in the youngest gravel sequence are up to two orders of magnitude larger than gold grains in the parent alluvial source. Most of the gold in the tectonic sediments is highly irregular in shape, commonly with delicate surface textures which could not have survived fluvial transport and are indicative of authigenic precipitation. Some coarse grains have been rounded by recycling, and further addition of authigenic gold has occurred. Placer gold values result from both physical and chemical enrichment during sedimentary recycling. Continued range uplift and back-thrusting of sediments on to the ranges results in recycling of earlier formed placer sediments. They also result in further enrichment of gold values through the incorporation of additional supplies of the parent alluvial source sediment The host sediments are widespread along the ranges and are not confined to sites of historic mining activity.

Jan 1, 1992

By L. C. IlsLey

A specially recommended cable is a rubber-sheathed cable that has met the minimum performance requirements for cables as set forth in Schedule 20. The first in the series of recommended cables was listed September, 1930, by an ad- vance notice published as Information Circular 6375 which described the conditions under which the cable tests were made. Since that time six additional cables have met the test re- quirements and have been specially recommended. The complete list of specially recommended. cables is as follows: Specially recommended-cables Cable Symbol No. Hazacord No. 2 BM1 Stranding 19 x 7 Hazacord No. 3 BM2 do. Hazacord No. 4 BM3 do. Super-service No. 3 BM4 7 x 19 Super-service No. 2 Super-service No.. 4 BM5 do. BM6 do. Super-service No. 4 BM7 7x 7 Manufacturer Hazard Insulated Wire Works (division of the Okonite Co.) Do. Do. Rome Wire Company (division of the General Cable Corporation) Do. Do. Do. The cables listed were all twin (parallel duplex) cables having outer belts or cov- erings of approximately -inch high-grade rubber compound, and have the same general appear- ance and relative dimensions as the types of twin cables in general use. The cables were tested under conditions designed to show their approximate perform- ance under mine conditions. Only twin-type cables have met these test conditions. Although the recommended trailing cables are much better and safer for mine use than other cables and withstand being run over by a 7-ton car, they should not be considered as 100 per cent safe. The 7-ton car test represents the minimum limit requirement effective at present under Schedule 2-C, but the test car operates on a straight and level track, and thus does not represent the more severe conditions of mine use such as might result from uneven and curved tracks.

Mar 1, 1931

By A. Mazzucato

This paper presents the experimental results of driving and load tests on an instrumented pile driven into a test pit filled with fine homogeneous sand.

Jan 1, 2010

By A. Bascetin

Waste materials caused by mining activities are an important environmental problem. Paste technology is a good alternative for waste management because it has many benefits in the aspects of environment, cost and safety. Disposal of process wastes in paste form is an attractive option for waste management, as it eliminates or reduces the risks associated with conventional methods. Due to the geotechnical characteristics of the paste, it is very similar to soil materials. So determining the geotechnical properties of the paste material is essential to durability of the paste. The some important geotechnical properties are compressive strength, porosity, shear strength, hydraulic conductivity, water content, consolidation, etc. In this study, the important parameters and the relation between them were investigated and obtained some results which will affect for optimum design of waste management.

Jan 1, 2012

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. (a) In-shaft equipment design and specification criteria are considered as they influence guideline preparation. (b) A comprehensive review of hoist electric drives and controls as applied to mine hoists is set forth with special reference to duty cycle calculations and their effect on electrical component selection.

Jan 1, 1988

[Adams, Douglas K General Electric Co., P.O. Box 2331, Denver 1, Colo. Adams, Kenneth L Peabody Coal Co., 301N, Memorial Dr., St. Louis, Mo. 63102 Allen, Earl W Mine Safety Appliances Co., 257 Rio Grand St., Salt Lake City, Utah Allen, Dr. Harry C U. S. Bureau of Mines, Washington, D. C. 20906 Alston, George L Mine Safety Appliances Co., 201 N. Braddock, Pittsburgh 8, Pa. Archer, Bryan J., Jr Peabody Coal Co., 421 Glenwood St., Grand Junction, Colo. Arentzen, E. M Lee-Norse Co., P.O. Box 582, Charleroi, Pa. Arentzen, L. E Lee-Norse Co., 6030 W. 55th Pl., Arvada, Colo. Arentzen, Rolf F Lee-Norse Co., Box 582, Charleroi, Pa. Artis, Cliff E Big Horn Coal Co., 247 Sherman Ave., Sheridan, Wyo. Atchison, Lee Atchison Construction Co., Drawer D, Aztec, N. Mex.]

Jan 1, 1967

The use of belt air in underground coal mines has been a continuous discussion since it was first introduced in the Federal Coal Mine Health and Safety Act (Coal Act) of 1969. Although the Coal Act prohibits the use of belt air to ventilate active workings, there were two exceptions prior to the 2004 Final Rule. There have been several major studies/rule-proposals by MSHA since 1985 and the most recent of which is the Technical Study Panel (TSP) established by the Mine Improvement and New Emergency Response (MINER) Act of 2006 to study the use of belt air and related issues. This paper reviews the history of belt air use, its associated controver-sies, and more specifically, the 20 recommendations unanimously approved by the TSP.

Jan 1, 2009

By N. I. Aziz, I. Tague, P. Mackenzie-Wood

The recent mine disasters in Australian coal mines have initiated an introduction of Self-Contained Self-Rescuer (SCSR) as component in the development of new escape strategies for miners. These self-contained self-rescuers are closed circuit, demand sensitive breathing apparatus that make oxygen available to the wearer for a nominal period of time. Their operation is completely independent of the surrounding atmosphere. Once properly donned, the SCSR can assist a miner to escape from an area containing smoke, toxic gases or an oxygen deficient atmosphere. The duration of a typical SCSR is usually taken at the point of complete collapse of the breathing bag which is accompanied by an increase in breathing resistance and inhaled levels of carbon dioxide. Because the oxygen consumption (V02) and the heart rate are correlated, a prediction of V02 and consequently the duration of an SCSR can be made by monitoring the heart rate. Thirty-seven volunteers participated in field simulated escape trials at four underground coal mines. The results from the field trials suggested that oxygen consumption depends on the heart rate, the body weight and exercise rating of the miner. All the volunteers were asked to fill out the questionnaires to evaluate the performance of the units. The miners indicated that they could tolerate the inhaled temperature without any difficulty to breathing resistance. A complete statistical analysis of the field results is also presented.

Feb 24, 1997

By T. Johnson

Hydrometallurgical processes can be exceptionally corrosive. This is particularly true in acid leaching processes for copper, cobalt, nickel and rare earth elements. In the last five years, several large hydromet plants have been built in North America (Vale - Long Harbour, Baja Mining ? El Boleo and MolyCorp - Mountain Pass). Hundreds of storage tanks, extraction vessels and electrowinning cells along with miles of piping were designed and fabricated to withstand the aggressive environments inherent in these processes. One key element all three projects had in common was the extensive use of FRP in equipment design. As a material of construction, FRP provided equal if not improved durability relative to alternative corrosion resistant alloys at a considerably lower cost. This paper will highlight the extensive use of FRP in these three world scale projects and why it was chosen for each process.

Jan 1, 2013

By V. Yahorava

Resin-in-pulp (RIP) technology has recently often been considered for the direct recovery of base metals and uranium from dense pulps. Implementation of RIP will eliminate the requirement for any solid-liquid separation downstream of leaching and has the potential to combine the recovery and purification steps, hence reducing both capital and operating costs. The recovery of the valuable metal is expected to be higher when RIP is used, especially where the leached solids are difficult to settle or filter, and to wash. The main concerns about the use of RIP for uranium recovery from dense pulps are the impact of silica on the resin?s metallurgical performance and the operating costs that would be associated with resin loss. Although a number of resin manufacturers have been developing much improved RIP-grade resins, it is critical that the most cost-effective resin be selected. Mintek currently is doing a significant amount of work on silica fouling of RIP-grade strong-base resins in acidic leach liquors and the effect it has on the performance of the resin, including its durability. This paper describes the results of the test work done on silica fouling and its impact on plant design input data. Resin durability test work was done using various laboratory techniques, but durability was also evaluated on a relatively large scale using actual pumps, screens, and mechanical agitation. Based on the results generated, a preliminary economical evaluation was done to estimate the impact of resin loss on the overall economic viability of a specific application. Keywords: resin-in-pulp, silica fouling, resin loss, equilibrium, kinetics, elution, durability, mechanical strength, resistance to attrition.

Jan 1, 2009

By E. M. Murphy

Comparative data from ASTM method of test E-162 and large-scale trials in the Experimental Mine show that the flame-spread quality of brattice cloth and other ventilation control materials can effectively be evaluated by either method. Materials having a flame spread index of 25 or less, as determined by the simpler and more economical laboratory test ASTM E-162, do not present a serious fire hazard when used in coal mines.

Jan 1, 1972

By A F. Cooper

Otago Schist in the Mount Patriarch, High Burn and Cameron Creek areas of northwest Otago grades from textural grade IIA in the east to textural grade III in the west. The entire region is of the actinolite-pumpellyite metamorphic facies. Lithologies in the area are interbedded turbidite sequences comprising pelite and psammite together with pebble conglomerate, greenschist and metachert horizons. The mineral assemblage of the schist is typically quartz-albite-epidote-actinolite-pumpellyite-chlorite-stilpnomelane-calcite. A good foliation is well defined in the area and is predominantly parallel to bedding, except in hinges of mesoscopic isoclinal folds. The structure of the area appears to be defined by a large southwest plunging isoclinal fold defined by bedding with a steeply dipping axial planar foliation. Kink folding and dextral strike-slip faulting in the area postdates the ductile phase of deformation. Pods of rhodonite, rhodochrosite, spessartine garnet, coombsite, caryopilite, Mnstilpnomelane and Ni-Cu-Zn sulphides were found in concordant metachert layers in the Mount Patriarch area. Metachert was also found in float in the Cameron Creek area. Malachite occurrences relating to copper mineralisation were also noted in a green metachert horizon on the eastern flank of Mount Patriarch. The coombsite, in only the third observation worldwide, is the most Fe-rich variety reported.

Jan 1, 2003

By Nicholas J. Grant, Bill C. Giessen

The phase diagram Ta-Ni has been treated repeatedly; investigations up to 1958 are summed up in Ref. 1. Since then, an equilibrium diagram has been presented by Kornilov and Pylaeva.2 They found the following intermediate phases: Ta2N; (CuA12 type),3 "TaNi" (p phase, Mo8Co7 type), TaNiz, and TaNi3 (Ticus type).5 Of these, the crystal structure of TaNin remained unknown, and no further literature reference was found. According to Kornilov and pylaeva,&apos; TaNil melts peri-tectically at 1420°C. A 5-g alloy of Ta + 66.7 at. pct Ni was prepared by inert-gas arc melting using 99.95 pct Ta rod (NRC-MG) and 99.9 pct Ni shot (Fisher). The weight loss after three melts was <2 mg; a microscopically homogeneous ingot resulted. As shown in Ref. 6, no oxygen or impurity pickup needed to be considered under these conditions. Specimens were annealed for 15 hr at 1350°C, 15 hr at 1205oC, and 15 hr at 875°C with subsequent powdering and stress relief for 10 min at 1350°C, 15 min at 1205oC, and 1 hr at 875oC, respectively. Micrographs and X-ray analysis (114.6 mm Norelco camera, filtered CuK, radiation) showed homogeneous one-phase alloys in the as-cast state and at all three temperatures, all having the same powder pattern except for broad lines in the as-cast state. From this it is concluded that either TaNi, melts congruently or its melting behavior is a transition between the eutectic and peritectic cases. Since it was found that very slight surface contamination on stress relieving can considerably alter the structure of similar phases (e.g.,TaPt3),7 patterns before and after stress relief were also compared; they were identical except for line broadening in the non-stressrelieved condition, and two faint impurity lines in the stress-relieved samples. The powder pattern is presented in Table I. All lines were accounted for by indexing with a tetragonal lattice, 0Yh- I4/mmm , with a, = 3.154 ± 0.001A, co = 7.905 * 0.002i and c/a = 2.506. The atomic positions are: 1000; 1/2, 1/2, 1/2] + 2Ta(a): 000; + 4Ni(e): *(002); z = 0.333 * 0.002 This proves TaNi2 to be a representative of the MoSiz (Cllb) type. The variable parameter was determined by grouping the visually estimated intensi- ties according to their 2 indices, plotting their F values, and varying z for best fit, which was obtained at z = 0.333= 1/3. Since absorption was not considered, only the relative intensities with similar 28 can be expected to agree. The interatomic distances are presented in Table 11; the standard error is *o.o2A, resulting chiefly from the uncertainty in z. These distances indicate a coordination number 10 for both kinds of atoms and show that the pseudohexagonal layers along (110) are rather un-distorted. The mean atomic volume of 13.1A3 is close to the Vegard&apos;s law value of 13.3A3, showing

Jan 1, 1964

By Karel Van Acker

The automotive is a sector where energy consumption during the use phase prevails over the production and the end-of-life phase. Therefore, a lot of research and innovations at replacing classical steel parts by lighter materials like light metals and polymer composites. While composites are very attractive for the use phase of cars, their introduction suffers from the limited end-of-life options for composite structures. An extensive life cycle analysis for a reference car design has been conducted to study the effects of replacement of conventional steel structures by lightweight carbon fibre composite alternatives. The study also takes second order effects in the design of the car into account. The opportunities and treats of the trend towards more intensive use of carbon-fibre composites in car design are identified. A discussion on the potential of other types of composites for the automotive in terms of sustainability considerations is added.

Jan 1, 2010

By M. L. Young, J. B. See

Effective thermal conductivities of packed beds of chromite ores by M. L. YOUNG, B.Se. (Rand), M.Sc. (Rand) (Visitor) and J. B. SEE, B.Sc. (Hons), Ph.D. (New South Wales), M.I.M., M.I.M.M. (Member) The effective thermal conductivities in stagnant air of packed beds of fines, lumps, and indurated and pre-reduced pellets of two chromite ores with different chromium-to-iron ratios were determined in the temperature range 300 to I 100°C by the heat-sink technique. Packed beds of fines, whether of the size fraction between 20 and 65 mesh, between 65 and 100 mesh, or between 100 and 150 mesh, were found to have the same values of effective thermal conductivity. For one ore, the effective thermal conductivities of packed beds of fines between 20 and 48 mesh at tem peratures above 600"C were higher than those for finer particles. This difference is explained as being due to the increase in importance of radiation heat transfer, but no definite conclusions are reached about the relative contributions of conduction and radiation heat transfer to the effective thermal conductivities of packed beds of fines between 20 and 48 mesh. Two published models were used for the theoretical prediction of values for thermal conductivities of the indurated and pre-reduced pellets as well as of lump ore. The experimental and theoretical results were in good agreement in view of the uncertainties in the assumed values of emissivity and thermal conductivity of the chromite ore.

Jan 12, 1976

By Roger A. Bullivant

As the UK&apos;s foremost domestic foundation underpinning contractor over the last 25 years it has become abundantly clear that the size of the repair market, some £500m per annum is a significant waste of resource and cost. To experience this scale of foundation failure in mainly new construction less than 20 years old is unacceptable. This is being further endorsed by our contracting experience in the USA over the last 10 years. Our foundation repair systems are mainly based upon the use of driven mini piles and it was considered appropriate that this type of pile should be upgraded and used on new build construction where the ground was marginal or bad.

Jan 1, 1995

By Bruce Conard

For many years, Bruce Conard has been engaged in reading about and discussing the desired sustainability of the mining and metals resource industry. He has, however, become concerned that there is a greater issue that requires our urgent attention: what challenges do we face as a global society? His Distinguished Lecturer presentation traces the idea of environmentally sustainable economic development but concludes that a business’ interest in its sustainability is predicated on the sustainability of our global society. Conard reviews some of the most serious challenges, including population growth, clean energy supplies, freshwater availability and climate change, and calls on scientists and engineers not only to apply their skills in helping solve these challenges, but most urgently, to speak with intelligence and passion about the need to act now.

Jan 1, 2014

By J. de Villiers

Through the application of the Rietveld method, X-ray diffraction analysis has developed into a fully quantitative method for phase analysis. The Rietveld method itself has progressed from an unstable method that required constant operator intervention to a stable and robust method suited even for routine analysis. The method, however, requires a good initial calibration and periodic checks on its precision and accuracy. Several examples from minerals processing, pyrometallurgy, and materials science show the strengths and applicability of the method. The limitations and sources of error are also discussed.

Jan 1, 2007