Search Documents

By T. J. Kolokoto

This paper is based on a project conducted at Khomanani 2 shaft, Anglo American Platinum Limited. The main objective was to find an alternative support element in stopes to address the falls of ground (FOG) problem experienced at this shaft. Literature review was the major method used in the investigations. Resin bolts or any 1.5 m in-stope roofbolts were considered. The shaft was making use of 0.9 m long friction bolts, and these could not prevent the FOG experienced. Observations indicated that the FOG resulted in fall-out thicknesses averaging to 1.1 m, which is greater than the supported length of the friction bolts. The implementation of 1.5 m long bolts was recommended as a result of the project. These bolts will be able to address the fall-out thickness and provide sufficient support resistance to mitigate FOG. The chosen support element will result in a relatively small increase in support costs.

Jan 1, 2013

The success of smooth blasting essentially depends on geological condition of rock. Also, in the perimeter hole, borehole pressures with light, well-distributed explosive loads are important to minimise overbreak. In order to simulate perimeter holes with scaled model test, the borehole pressure was considered as a factor of scale. Hydraulic oil pressure is applied as borehole pressure instead of using explosives and detonators in order to remove the undesirable effects of detonators in an experimental set-up of just two perimeter holes in a tunnel blast. The borehole pressure on a perimeter hole is nearly reproduced with hydraulic pressure which is generated by non-electric detonators in the hermetical cylinder.

Dec 6, 2010

By Jo Katembo, Patty Bwando, Patient K. Ilunga, Yves Kalubi, Emman Mulaj

"From 2010, the dolomite concentration in the ore fed to the Usoke Plant increased, resulting in a significant increase in the gangue acid consumption and Mg build-up in the circuit, and thus an increase in the Mg:Co ratio in the plant solutions. This affected the Co salt grade, reagent consumption, filtration and drying capacity. Efforts were put in place to minimise the acid consumption and consequently the Mg dissolution (such as use of pre-diluted acid), but the benefits were negligible. Various efforts were then initiated by CHEMAF to improve the cobalt plant productivity (quantity and quality) by process changes, dual precipitation and seed recycle. The positive results obtained in the laboratory were successfully implemented on plant scale. A change in the process from a single-stage precipitation with Na2CO3 to dual precipitation using a combination of Na2CO3 and NaOH improved the capacity of the Co salt filtration by 30%, the Co salt grade and drying capacity by 50%, and reduced the reagent consumption by 22%. Implementation of precipitate seed recycle increased Mg rejection by 40%, improving the Co salt grade from 20% to 25%, and yielding a further drop in reagent consumption. INTRODUCTION CHEMAF (Chemicals of Africa), a mining company located in Katanga province of Democratic Republic of Congo (DRC), has been operating since 2003. The Usoke hydrometallurgical plant treats the Cu-Co ore from the Etoile pit to produce Cu cathodes via a leach–solvent-extraction (SX)–electrowinning (EW) circuit and Co salt via a selective precipitation process. The plant was designed to treat run-of-mine (ROM) ore grading 6% Cu and 1.5% Co; but, in 2008, due to a decline in grades, a heavy-media separation (HMS) plant was commissioned to enrich the low-grade ROM (3.5% Cu and 0.5% Co) up to 8% Cu and 1% Co before feeding it to the hydrometallurgical plant. Co is recovered by precipitation of Fe and Al with limestone, followed by Co precipitation as Co carbonate using sodium carbonate (Na2CO3), also known as soda ash. 85% of the final effluent from cobalt precipitation is recycled back to the plant as process water; the balance, 15%, is bled out and compensated for by fresh water top up to control and retard the rate of sodium sulfate build up."

Jan 1, 2015

By S. J. Ramokgopa

The development of the modern State and the growth of capitalism involves a complex process of interaction between cross-cutting structural dimension: first between politics and economics and, second, between market and hierarchy. Central to such developments are political economies of scale. Mineral specialization in the Third World developed within the framework of an international extension on oligopolistic structure of the advanced capitalist economies of Western Europe and North America. Up to the late 1960s, the world mineral and metallurgical industry was closely controlled by a handful of Western mining and industrial groups. To the extent that, foreign control of the mining sector was seen in the Third World producing countries both as the essence of foreign domination and as its major symbol. In some newly industrializing countries, the State took a more direct role in tying the economy and society together. Central to this process was the growth of large-scale finance capital. From early 1959to the mid-1970s, metal consumption in industrial countries expanded well beyond their domestic mineral endowments. And a free access to Third World minerals was a major element of the economic dynamism of these countries throughout that period. With the change in the characteristics of international investment, Africa has become less important as an outlet for capital exports of European countries. Actually, the African continent now receives only a very minor share of direct foreign investments of Western enterprises. International political economy is concerned first of all with the relationship between the economic and political domains across territorial boundaries. Second, attention should be drawn to the role of the State as the focus of decision-making in a system of competitive States, that is in turn, interdependent with a trans-national market economy in which mining and metallurgy are essential activities that affect the politics of the State, and how this in turn, rebounds on the politics of the international system. Understanding the role of the State must go beyond the glib pronouncements on the ?national interest?. How, and whose interest, the ?national interest? is determined, is precisely the problem. This implies a third theoretical problem that must be addressed: the linkage between the domestic and international domains (or levels of analysis), given that political-economic processes clearly cut across the lines of political decision-making constituted by the institutional structures of the State. Situating the State and economic interests within this vast ?state-society? complex that we call the global order will be a crucial problem for any theoretical approach that involves mining and metallurgy.

Jan 1, 2002

By M. Deal

Particle size analysis is a fundamental measurement utilized in the mining industry, especially in comminution, hydrometallurgy, and mineral processing. While sieves and cyclosizers are the standard methods used to determine particle size distributions, in recent years alternative instruments have been developed that claim to provide more rapid and equally reliable results. Newmont Metallurgical Services has implemented the use of two such instruments, along with traditional methods (sieves and a cyclosizer), on a daily basis. The Malvern Mastersizer 2000 laser analyzer is a wet sample system that can analyze particles in the size range 0.02µm to 2000µm, and the Horiba CAMSIZER® is a dry system that can analyze particles in the size range of 30µm to 30mm using digital image processing. A comparative analysis has been performed to determine the applicability of each particle sizing method in laboratory testing.

Jan 1, 2011

By K. K. Kershner

The purpose of this investigation was to develop methods, on a laboratory scale, for recovering tin from Bolivian metallurgical slimes. Petrographic and chemical analyses were made of slime ore fractions from several well-known tin operations. High percentages of the total tin were volatilized as chlorides at temperatures below 600° C. Under optimum conditions reaction rates were relatively rapid, and the chloridizing reaction approached completion. Owing to the low temperatures involved and the high yields of tin, the process was considered to have possibilities for treating Bolivian slimes on a commercial basis. ACKNOWLEDGMENTS Appreciation is hereby extended to the Patino Mines and Enterprises, Inc., of Bolivia, for supplying slimed tin ores that were used in the experimental work. This company has since been nationalized.

Jan 1, 1959

By L. J. Moore

Introduction Hydrometallurgical solvent extraction (SX) processes – featuring large quantities of combustible or flammable organic solvents - are common in the mining industry for recovering non-ferrous metals such as copper, nickel, cobalt, uranium, tungsten, iodine and lithium. Recent fire loss incidents and the widespread use of sub-grade tank farms and piping trenches, plastic piping, poor drainage, and closely spaced buildings demonstrate opportunities to improve the use of Inherent Safety (IS) in this industry. The mining industry has designed and constructed facilities with an emphasis on personnel safety, production efficiency and cost effectiveness. The use of IS to eliminate or minimize property fire exposures has not seen widespread practice. Lessons learned from the mainstream CPI have not been communicated or applied. As an example, copper SX plants have consistently used design of gravity flow as a cost and production-effective solution for transferring liquids and minerals through the process. In fact, Jergensen1 recommends to “utilize gravity to the fullest extent possible” in design of SX plants. This philosophy has been achieved by laying out SX plants with process equipment at different grade levels so that solutions can flow “downhill”. Because of the use of large quantities of flammable liquids and the potential for these liquids - if released – to flow unimpeded into other areas – gravity SX processes represent severe inherent fire consequences unless costly barriers, drainage and channeling are also provided. It appears that little thought has been given to the fire protection consequences and challenges of this design feature during the evolution of SX plants and most copper SX plants constructed today use some form of a sub-grade processing area (tank farm) and one-way gravity flow. While this layout is used to assure a cost effective operation it has resulted in significant exposures to high value production. The use of sub-grade production units is an inherently unsafe layout where flammable liquids are used and is a layout that would rarely if ever be used today by the mainstream CPI. Gravity-assist layout is only one example where copper SX plants have been designed and constructed without IS in mind. The use of combustible and frangible corrosion-resistant materials – such as glass, wood and plastic - for flammable liquid storage, processing and piping systems has significantly increased the hazards of these facilities. These materials of construction are not rigorous and allow for rapid failure and release of flammable contents during fire exposure. The use of combustible or frangible systems to handle or transport flammable liquids is not a practice seen today in the CPI.

Jan 1, 2006

Drilling in the south of the Rapahoe Sector at Greymouth Coalfield has demonstrated the existence of thick coal seams in the upper Rewanui Member. Seam correlation is handicapped by complex lithostratigraphy and laterally variable geophysical log profiles. An integrated investigation of coal measure stratigraphy, coal petrology, and proximate analyses, suggests a feasible model whereby most of the major seam intersections belong to a single horizon. Coal properties vary laterally in response to original swamp conditions, which are believed to have ranged from well-drained to ponded. A new model of peat accumulation is proposed for the northern Rapahoe Sector, whereby Upper Rewanui peat accumulation occurred on a flood plain between the levees of a major south southwest-flowing fluvial system in the east and the toe of a western alluvial fan.

Jan 1, 1985

By Leroy O. Gieseke, John B. Begley

If the particles produced and transported in your plant are as chunky as rough crushed coal or as fine as cement, there are probably several conveying and elevating systems suitable for your operation. The problem is deciding which is most suitable in terms of space, energy cost, allowable product degradation, productivity, and angle of movement. Each conveying and elevating method should be fit to the products it can handle successfully, to desirable economics, and to suitability for the overall operating scheme. Matching along these lines will result in selection guides that should be useful for many years, although design evolution is expected for the materials handling equipment involved. There are several common bulk material handling devices for moving solids: belt conveyors, screw conveyors, bucket elevators, chain conveyors, and en-masse conveyors/ elevators. En-masse conveyor/elevator equipment is commonly compared and contrasted with the other devices. These comparisons often involve en-masse versus all others. En-masse has developed into a versatile technique because the machines can move materials horizontally, vertically, or in closed circuit. Such machines unload, elevate, store, reclaim, and distribute materials-all without ancillary equipment except for chutes and gates. Bulk material can be carried, as with a belt conveyor or bucket elevator; pushed, as with a flight or screw conveyor; bumped, as with a vibrating conveyor; blown, as with a pneumatic conveyor; fluidized, as with a dense phase pneumatic conveyor; or by applying internal forces to it to induce "en-masse" flow. Conveying en-masse is analogous to the flow of a fluid in an open channel, and elevating en-masse is analogous to the flow of fluid in a pipe. In the case of a fluid, flow is caused by a differential in pressure. With en-masse movement, flow results from resistance to shear induced by the movement of chain and flights.

Jan 12, 1980

By Ronald F. Balazik

[This Bureau of Mines study is intended to identify and evaluate potential effects of impending large-scale U. S. rail line closings (abandonment) on domestic nonfuel mineral industries. This is the first nationwide study of rail abandonment impacts focused on nonfuel minerals. The analyses presented is based principally on a survey of 200 rail freight records and on statistical tests that correlated 2,000 points in the Bureau's Mines Industry Location System (MILS) with 700 prospective abandonments throughout the United States. The conclusions derived from the analysis can be useful in evaluating proposed national rail abandonment policy rind legislation regarding nonfuel miner it shipping. Among these conclusions are the following: (1) Certain mineral materials (especially fertilizers) are likely to account for a large percentage of the rail traffic affected by abandonment in the next few years, but the total tonnage- involved will be small; (2) abandonment will adversely affect some mineral shippers, particularly local smart haulers; and (3 abandonment could significance reduce the opportunity to develop new resources or reopen defunct mining facilities. Despite these problems, however, the data examined in this study do not indicate that current abandonment trends will cause widespread disruption 01 domestic nonfuel mineral shipping.]

Jan 1, 1980

By Steven Derycke, Stephen C. Tadolini, Anand Bhagwat

"The tensile and shear strength of intrinsic bolting support systems has always been a major concern of designers. A comprehensive laboratory testing program was designed to evaluate the tensile and shear strength of individual wires and completely wound PC-strand cables. PC-strand cables with smooth wires and the recent anchorage enhancement innovation of indentation were evaluated and compared. The testing protocol detailed in ISO Standard 15630 utilizes a mandrel system that was investigated at 3 different diameters which alters the wire to mandrel ratio from 2:1 to 9:1. The results demonstrate that the difference between smooth and indented wires is statistically insignificant when larger diameter mandrels are used, and that indentation does not adversely affect strand properties and performance. Insight into the shearing mechanism and evaluation techniques are discussed with the introduction of triaxial loading to describe the PC-strand tensile and shearing mechanisms. Another important result indicates that the shear strength of PCstrand cable bolting systems has a greater shear strength value than traditional steel bar bolting systems.INTRODUCTIONPC-strand cable bolts have proven to be a global cost effective ground control solution in metal/non-metal and coal mines. The inherent strength to weight ratio of cable supports, combined with flexibility has been used in underground entries that range from 20 to less than 1.2 m in height (65 to 4 ft). In coal mining, the systems are used as primary and secondary support installed both passively or actively with installation tensions that range from 38 to over 178 kN (8,500 to 40,000 lbs) . While cable can be specified in several diameters, the most predominant sizes in the US remain 15.2mm (0.6 in) and 18mm (0.7 in). The capacity of the systems defined in the ASTM 432-13 is 90% of the minimum strand strengths of 260 kN (58,600 lbs) and 320 kN (72,000 lbs), respectively.Cables are not only suitable to support vertical loads, but are also often used to effectively support fractured and jointed materials and can be exposed to shear forces across the wound PC-strand structure. In fact, Goris et al. reported that cable bolts placed across jointed surfaces could more than double the shear resistance. These results were duplicated for both smooth and rough jointed surfaces (Goris et al., 1996). An example of tensioned cable bolts used to support a fractured and sliding roof in a longwall tailgate entry is shown in Figure 1."

Jan 1, 2015

By Rodney D. Lamond

The need for blast vibration monitoring can be attributed to a combination of three factors: Structural damage, Blast design and Human annoyance. Traditionally, vibration damage criteria are prescribed in terms of peak particle velocity (PPV), as measured or predicted in the ground surrounding a blast. The PPV in the vicinity of a blasthole is strongly influenced by the quantity of the explosive per delay. In general, the existing prediction models give reliable results but fall short of addressing the change in PPV when the charge is decoupled and/or distributed.

Jan 1, 1995

By Philip J. H. Ball

The new application and development of grout jacking processes has combined, over the last decade in particular, to provide a method by which the effects of new underground construction on superficial structures can be controlled to acceptable levels. This paper sets out the basic principles, processes and limitations of compensation grouting. It describes key elements of the philosophy and design and details the control systems required to perform satisfactorily. To illustrate the application, a case history is described for the construction of a shaft and tunnel within and beneath the prestigious structure of Harrods in London.

Jan 1, 2000

By S. Brummelkamp, G. Van Weert

Separation of minerals by shape has received little attention, since minerals normally do not break into different shapes during crushing and grinding. However, comminution of consumer wastes generates opportunities for novel separations based on particle shape. For instance, ductile plastics are broken into longer curved shapes, whereas brittle plastics yield angular particles. Using spouting beds for particle separation in water requires controlling the spout's instability. The preferred geometry for such redesigned spouting beds is reported. Plastic cylinders, discs and spheres were separated as a function of rising water velocity and amount of particles in the system. By using 5 mm particles, differences in settling behavior could be video recorded.

Jan 1, 1999

By Darrell L. Beddard

Pile driving started October 29, 1993 and was completed on January 27, 1994. Field work included driving piling from ground surface at one site and at or near proposed footing elevations for the remainder. Piles were driven to specified tip elevations or the elevations directed by the Project Manager. In an attempt to address what installation technique(s) performed the best, several methods were used, including varied predrilled depths, open ended piles, closed ended piles, and the use of both impact and vibratory hammers. Piles were driven closed ended where possible to study the feasibility of this option to reduce construction costs associated with pile cleanout. Piles were driven to different depths to measure capacity variations. The 24-inch (610 mm) diameter piling were driven in one piece while the 42-inch (1.07 m) diameter piling was driven in two segments. A total of 79 piles were driven for the four sites, 74 of the 24-inch (610 mm) diameter and 5 of the 42-inch (1.07 m) diameter. Various hammers were used to determine which hammers provided viable solutions to the potential problems anticipated in the design phase. Hammer selection was based on the driveability studies. Equipment included a 175 ton (1.56 MN) crane, support crane for pile stabilization, crane mounted auger drill, offshore leads, Delmag D30-32, D46-32, and D62-22 diesel hammers, an HPSI 2005 single acting hydraulic hammer, a Foster IHC S-90 double acting hydraulic hammer and a Kencho VM2-25000AII vibratory hammer with the weights set to produce 17,500 pound-inch (1.98 kN-m) of eccentric moment.

Jan 1, 1996

By Charles Sabine

The U.S. Bureau of Mines studied mines and prospects in the Bristol/Granite Mountains Wilderness Study Area (WSA) in 1982. The 45,000 acre WSA, located in the eastern Mojave Desert of California, is underlain by Mesozoic plutonic rocks with scattered roof pendants of Paleozoic (?) metasedimentary rocks. Two mines and six prospects are identified; one mine, the Silver Lode Mine, and a prospect of unknown name are adjacent to the area. The Silver Lode Mine has occurrences of silver, lead and zinc. Within the study area, the Comanche Mine has occurrences of iron and copper and the Iron Victory Prospect has an occurrence of iron. None are large enough to constitute a resource. Occurrences of magnesian marble at the Comanche Mine, Iron Victory Prospect, and elsewhere in the area contain too much MgO for commercial use other than agricultural soil supplements or crushed stone. Transportation costs to markets would exceed the value of the rock. At the Comanche Mine, situated in a roof pendant of marble, about 10 tons remain of a 110-ton pod of magnetite which contained 42.5% iron, and less than 50 tons remain of a mineralized fault breccia which averaged 2.5% copper and 0.3 oz/ton silver. Magnesian marble contained 41 to 45% CaO and 14 to 16% MgO. Primary and secondary silver, lead, zinc, and copper minerals are disseminated along altered joints and in quartz veins in quartz monzonite at the Silver Lode Mine, adjacent to the WSA. Analytical data are sporadic; samples contained as much as 0.12 oz/ton gold, 1.8 oz/ton Silver, 1.1% lead, 3.8% zinc, and 0.3% copper. Mineralized zones in the workings are not resources, but they might indicate possible silver-lead-zinc resources at depth. At the Iron Victory Prospect, lenses of magnetite and hematite with some chalcopyrite occur in a skarn lone in a marble roof pendant. About 110,000 tons of iron-rich rock, averaging 47.2% iron, are present; the largest lens contains about 30,000 tons. About 150,000 tons of magnesian marble, averaging 41.0% CaO and 11.7% MgO, are also present. Deposits of stone, and sand and gravel in the WSA are too distant from markets to be resources. Occurrences of energy minerals were not identified.

Jan 1, 1984

By Arel B. McMahan

The U.S. Bureau of Mines investigated 21 mines, prospects, and mineralized sites in and adjacent to a 38,713-acre portion of the 255,058-acre Kingston Range Wilderness Study Area in 1983. The study area is 35 miles north of Baker, CA in the Mojave Desert. Mineral deposits in and adjacent to the study area are in altered carbonate rocks intruded by diabase sills near monzonite porphyry contacts. Monzonite porphyry forms the core of the Kingston Range and underlies about 70 percent of the study area. Sedimentary carbonate rocks are exposed in bands on the north and east boundaries and as isolated roof pendants in the southeastern portion of the study area.

Jan 1, 1986

By Lucia Kuizon

The Miranda Pine Roadless Area Review and Evaluation (RARE II) study area (No. 5114) comprises 12,600 acres (5,100 ha) in Los Padres National Forest in Santa Barbara County, California, about 15 mi (24 km) east of Santa Maria (fig. 1). Mineral investigations are made by personnel from the U.S. Bureau of Mines on National Forest lands identified as Further Planning Areas in the RARE II program. The Bureau of Mines reviewed literature, mining claim records, and production files; examined the study area; and sampled mineral properties where appropriate.

Jan 1, 1983

ALABAMA Anniston.-Carrington, F. G. Auburn.-Brown, R. L. Battelle.-Green, G. G. Bessemer.-Abbott, C. E. Dobbs, G. G. Ferguson, V. Birmingham.-Adams, J. H. Aldrich, T. H. Aldrich, T. H., Jr. Allen, A. W. Bonnyman, J. Bowron, J. Bush, M. W. Crawford, G. G. Crockard, F. H. Ellis, E. E. Fairbairn, C. T. Gallacher, J. Geismer, H. S.

Jan 1, 1917

By O. Ogunsola, M. Downing

This paper gives a brief overview of impacts of coal blending on coal-fired power plants performance and discuses the preliminary results of an on-going study aimed at evaluating the effect of coal properties on the effectiveness, compatibility and thermal reactivity of coal blends. Plant survey studies reported no significant impacts on an existing plant designed for a high rank coal when switched to a blend of low- and high- rank coal. However, slight modification of some aspects (handling, fuel storage/stockpile, transportation, preparation, and general housekeeping) of plant design and operation may be necessary. The preliminary results of an on-going study at the Mineral Industry Research Laboratory shows that more compatible and better blends could be made from coals where ranks are closer than from those where ranks are far apart.

Feb 24, 1997