Search Documents

By David Bendersky

This report covers a technical and economic investigation of old electrical power systems, equipment and practices being used in the metal/non-metal raining industry. The principal sources of information were the MSHA District offices, visits to representa¬tive mines and mills, equipment manufacturers and the literature. A list of 85 mines and mills, submitted by the MSHA Districts as candidates for this study, is given and their characteristics are analysed. The electrical power systems and practices at the 10 mines and 9 mills which were visited are described. The principal areas which do not conform to standard electrical practices are discussed with emphasis on the safety aspects of these practices. The costs to update electrical power systems and practices in metal/non-metal mines and mills are given. The principal findings of the study are summarized and recommendations are submitted.

Jan 1, 1980

By Li Zhou

The kinetics of the dissolution of galena was studied by monitoring the mixed potential of a galena electrode in ferric sulfate solutions. The results show that the mixed potential of the galena electrode fluctuated with time in a regular pattern in a 0.1 mol/L Fe2(SO4)3 solution of pH 1.66 and in a 0.01 mol/L Fe2(SO4)3 solution of pH 2.33 at 35°C. The periodic accumulation and precipitation of lead ions at the galena electrode surface and the cyclical variation in pH at the galena electrode surface caused the oscillation phenomena.

Jan 1, 2008

Copper ores are widespread through the Lachlan Geosyncline in New South Wales, but the size of the orebodies is generally small. The largest deposits occur in the Cobar district where an iron-rich copper ore type has been developed in Silurian sediments. Similar de- . posits to the south in the Nymagee-Mt. Hope-Melrose districts are related to quartz feldspar porphyries of probable Upper Silurian age. Deposits to the east in the Tottenham-Girilambone districts are less complex mineralogically and are possibly related to an ultra-basic source.Copper mineralization in the Highlands further to the east is often developed in Ordovician andesite or MiddleUpper Silurian acid volcanic sequences. The deposits in andesite contain considerably less galena than those in the acid extrusives; a small proportion of the mineralization in the latter has texture, mineralogy, and geologic setting analogous to the Captain's Flat copper-Iead-zinc deposit, for which both syngenetic and epigenetic origins have been proposed. Very little copper mineralization occurs within granitic material, even though rocks of this type ranging from Silurian to Carboniferous in age crop out through much of the geosyncline, and the extent of the metal contribution from plutons to the deposits in volcanics is open to question. Numerous deposits are known in the contact zone around Mid-Devonian and Mid-Carboniferous granites, however, and the formation of these orebodies has undoubtedly been influenced by plutonic activity. Small occurrences of copper with associated minor nickel sulphides are developed in a narrow serpentinite belt of possible Lower-Middle Devonian age in the southern section of the Highlands.

Jan 1, 1970

By Robb L. Swenson

Construction of foundations for the Skyway Segment of the San Francisco Oakland Bay Bridge required innovative techniques due to the mass of the structures being inserted and the unique subsurface of the Bay. Twenty of the pier structures required large sheet pile cofferdams. Eight other foundations were installed in open water without cofferdams at the deeper part of the Bay. This narrative will present the initial planning, as well as the stages of installation, for each type of foundation. The first section will discuss foundation constructability modifications made during the initial planning phases of the project. Considerable effort was expended by Caltrans, the owner, T.Y. Lin the designer, and KFM (Kiewit/FCI/Manson) the contractor in modifying the design to assure that required tolerance would be maintained during the installation of the foundations. The final section will describe the steps required for installation including: initial access dredging, installation of cofferdams, preparation required to install the footing boxes, footing box installation, foundation support pile installation, and pile to box connections.

Jan 1, 2013

By N. A. Eilertsen

Procedures of mining high-calcium limestone underground at the Kimballton mine of the Standard Lime and Cement Co. in Giles County, west-central Virginia, are described. Drilling and blasting procedures arc discussed in detail, and direct mining costs are tabulated in percentage of total cost. Output, about 1,725 tons of limestone a day, is attained with heavy trackless equipment by the room and pillar method of ruining; modified by benching floors. Operating features include underground air compression, electric-eye control of curtained doorways, use of a single jumbo drill rig for all drilling, and an effective plan for maintenance of equipment. The company's safety program has contributed to an outstanding safe mining record. The mina is integrated with a plant on the property which converts the stone to metallurgical and chemical grade lime.

Jan 1, 1964

By J. N. Van der Merwe

The results of over 900 coal strength tests done during the period 1993?1994 for the SIMRAC project COL021A were re-analysed with a view to find a method to delineate areas or seams that can be grouped together for analyses of coal strength and strength decay characteristics. It was confirmed that the strength of a coal specimen increases linearly with increasing diameter-to-length ratio and decreases exponentially with increasing size of specimen. However, by extrapolation of the data, it was shown that beyond a diameter of approximately 2 m, the size effect is insignificant. For larger specimens, the diameter-to-length ratio (referred to as the width-to-height ratio for full scale mine pillars) alone continues to influence the strength. The slope of the linear strength vs. diameter-to-length ratio relationship is independent of the size of the specimen and is not unique for coals from different mines. However, the intercept of that relationship is unique and is a function of specimen size. This offers a previously unknown method to distinguish between the coals from different mining areas and coal seams. Ranked from weakest to strongest, the samples tested from the different mines are in the order shown below, which roughly corresponds to the judgement of practising rock engineers in the field: ?Sigma ?ZAC ?Goedehoop ?Kriel ?Bank ?Blinkpan ?Secunda ?Greenside Arnot ?Khutala ?Delmas

Jan 1, 2003

By M. Aljarrah

The phase equilibria in the Mg-Al-Ca system was investigated experimentally by differential scanning calorimetry (DSC) and X-ray diffraction (XRD) techniques similarly the Mg-Al-Sr system has been studied using DSC and XRD as well as scanning electron microscopy/energy dispersive spectrometer (SEM/EDS) and quantitative electron probe micro-analysis (EPMA). A new ternary solid solution MgxAl4,xSr was confirmed in Mg-Al-Sr system, which is a substitutional solid solution of Mg atoms in Al4Sr. Maximum solubilities of 21.3 at.% Al in Mg17Sr2 and 11.4 at.% Al in Mg were observed. It was also noticed that Mg38Sr9 dissolved 12.5 at.% Al. In the Mg-Al-Ca ternary system, one of the invariant transformations predicted by thermodynamic modeling was verified experimentally and found to occur at 512°C with composition close to 10.8 at.% Ca, 79.5 at.% Mg and 9.7 at.% Al. A ternary solid solution (Mg,Al)2Ca was confirmed where large solid solubility of Al in Mg2Ca was observed.

Jan 1, 2006

By Flor De Cock

The paper reflects part of the work from the European Regional Technical Committee on Piles (ERTC3) during its mandate between 1994 and 1999, and, in particular, describes the find­ings from an International Seminar held in 1997 in Brussels on European practice for design­ing axially loaded piles. The seminar included contributions from 17 European countries, each of which provided a synopsis of their respective national design approaches. This paper pays particular attention to the design methods based on laboratory and in-situ test data for both bored and displacement piles.

Jan 1, 2002

By Youze Xu

The leaching and reduction of Cr(VI) in soils contaminated by chromium-containing slag were investigated with column experiments. The results showed that Cr(VI) concentration in leachate decreased from 988 mg L-1 to 407 mg L-1 after 7 days when water was used as leaching agent. However, Cr(VI) in leachate in culture medium treatment was not detected at above periods. In comparison, Cr(VI) concentration in leachate from autoclaved soil remained 398 mg L-1 at the end of experiment. The results indicated that the indigenous microorganism was capable of reducing Cr(VI). The amount of Cr(VI) reduction was 335 mg at the whole experiment period and the reduction rate was 67.09 mg d-1. Carbon supply showed minor effect on Cr(VI) reduction. However the reduction capability of Cr(VI) could be improved by combination of the carbon and the nitrogen. The optimal quantity was 5 g L-1 of yeast extract and 4 g L-1 of glucose.

Jan 1, 2009

By A. Andrews

Paper written on project work carried out in partial fulfilment of MSc (Eng) degree Solid state sintered silicon carbide ceramics are used in aggressive environments as sealings. There exist data concerning corrosion, but there are only few data concerning their electrocorrosion behaviour. Therefore the electrochemical corrosion of solid state sintered silicon carbide (SSiC) ceramics has been studied at room temperature in acidic and alkaline environments by using potentiodynamic polarization measurements. The investigation showed a pronounced electrochemical corrosion in bases and acids. In HCl andHNO3pseudo-passivity features due to the formation of a thin layer of SiO2on the surface were observed, whereas in NaOH soluble silicate ions were observed, resulting in more pronounced corrosion. The microstructural observations of initial and corroded samples reveal that the residual carbon found in the microstructure do not dissolve preferentially. Keywords: Corrosion; SEM; SSiC; polarization test.

Jan 1, 2006

By D. J. Steynfaard

Sishen Iron Ore Mine is situated 280 km north-west of Kimberley in the Northern Cape Province of South Africa. The mine produces and sells high quality iron ore of various specifications to various national and international clients. The saleable product is derived from the blending and beneficiation of different types and qualities of hematite iron ore. This paper documents the new developments which were implemented (or are in the process of being implemented) on the mine in the long-term planning, medium-term planning, grade control and material tracking in the beneficiation plant with special attention being paid to the quality of the final, saleable product. The process starts with the long-term planning where the pit shell and pit optimization is determined by Whittle 4X. New developments include the introduction of a linear programming based scheduling system to enhance the long-term schedule generated by Whittle 4X. The LP route was decided on in order to take into account all the constraining factors of the final product that could not be configured in Whittle. To complement this the XPAC Auto Scheduler scheduling package was introduced to do the medium-term mine scheduling. This 18-month rolling plan includes cost parameters to enable the planner to extract a detailed operational budget from the scheduling while ensuring that production standards are maintained and grade constraints are met. The existing grade control system was enhanced with GPS capabilities and a computer system to do material tracking. The high precision GPS system introduced on the shovels allows for the accurate control of the loading procedures at the mining face. Because of the complicated geology and grade composition of blasting blocks it is imperative to accurately differentiate between different materials in the same blasting block and being able to excavate that with the loading equipment. The GPS system on the trucks allows for accurate location monitoring of dumping in order to keep track of specific material types. The state-of-the-art material tracking system developed for Sishen will enable the grade control officer to keep track and record various parameters of the material from its in situ position in the blasting blocks, through the crusher and onto different stockpiles, in various stages of the beneficiation process and onto the blending beds, into the dispatching trains and eventually into the ships for international distribution. These developments elevate the Sishen planning and grade control systems to a new level of service excellence from which management can obtain accurate and timely information on product status. It also enables Sishen to maximize resource utilization while still complying with the tough market constraints.

Jan 1, 2003

By Pierre Roy, Claude Gosselin, Maryam Sadeghi, Michel Bourassa, Christian Rochefort, Claude Bazin, Gautier Mahieu, François Lavoie, Marilène Renaud, David Cataford

"Spirals are gravity concentrators used for the concentration of iron oxide minerals from ores. This paper presents the mineral size recovery curves observed for spirals operating in two Canadian iron ore processing plants. The size recovery curves are presented for rougher, cleaner and re-cleaner spirals. The partition curves observed for the spirals are significantly different than those observed for typical gravity concentration devices such as hydrocyclones or hydraulic classifiers. The size recovery curves show the complex behaviour of the minerals as they flow down a spiral and are analysed with a view toward process modelling and simulation. Initial simulation results show that gains in the iron recovery can be achieved by increasing the recovery of coarse iron oxide particles in the rougher spirals.INTRODUCTION Spiral concentrators are gravity based separation devices used for the preparation of coal, iron and different heavy minerals ores (Wills, 1992). The classification of the particles in spirals is based on the combination of gravity, centrifuge, drag, lift and Bagnold forces (Atasoy and Spottiswood, 1995; Burt, 1984; Bouchard, 2001). Several papers are dedicated to the analysis of the forces acting on the particles flowing down a spiral (Das and al., 2007; Sivamohan and Forssberg, 1985; Holland-Batt and Holtham, 1991; Holtham , 1992). Most of these papers aim at the development of a general model for the simulation of the classification of the particles for coal ore processing. Few papers deal with the operation of spirals for processing iron ores (Hyma and Meech, 1989; Srivastava, 2001; Dallaire et al., 1978) and fewer papers present results for spirals used as cleaners following a rougher stage. Since the classification in spiral classifiers is dependent on the particle size and specific gravity a partition or performance curve commonly applied to classifiers (Mai Manga et al., 2012) is used here to analyse spiral operation. Few papers were found to describe the operation of spirals in terms of partition curves (Atasoy and Spottiswood, 1995; Holland-Batt and Holtham, 1991; Richards et al., 2000). Most of the investigations presented the application of a model to simulate the position of coal particles of various sizes and specific gravities along the trough of a spiral (Kapur et al., 1996; Holland-Batt and Holtham, 1991). In addition most of the available literature on spirals deals with one stage of concentration by spirals (Dallaire et al., 1978; Das and al., 2007; Sivamohan and Forssberg, 1985) while industrial circuits usually consist of rougher and cleaner spirals."

Jan 1, 2014

By R. M. Waterstrat

X-ray diffraction and metallographic examination of binary Mn-rich alloys with Ti revealed the presence of intermediate phases in this system. A binary R phase has been identified and also a phase having an a-Mn type structure. The X-ray pattern of the phase TiMn3 is presented and a tentative phase diagram for the Mn-rich portion of this binary system has been constndcted. MANGANESE-rich alloys with titanium have been subjected to thermal analysis at temperatures down to 1100°C by Hellawell and Hume-Rothery.1 Their results indicate the existence of an intermediate phase TiMn3 in this binary system. This phase appears to coexist with the Laves phase TiMn2, and with terminal solid solutions based on the allotropes of manganese, at least down to 1100°C. The above investigators did not attempt to determine the crystal structure of this phase, however. Since, by analogy to the binary systems Mn-V and Mn-Cr3 one might expect to find a phase in this region of the diagram, it seemed desirable to obtain X-ray diffraction patterns of alloys in the concentration range in question, in order to ascertain whether the sigma phase or related structures occur. EXPERIMENTAL PROCEDURES Alloys were prepared by arc-melting electrolytic manganese and iodide titanium in a water-cooled copper crucible under a helium atmosphere. Excess manganese was added to each melt in order to allow for losses incurred during melting. The alloys were then wrapped in molybdenum foil and sealed in evacuated quartz tubes for annealing at various temperatures, as shown in Table I, followed by quenching in cold water. Although the inside of the tubes showed evidence for some loss of manganese from the specimen during annealing, there was no evidence of any reaction between the specimen and either the molybdenum foil or the quartz tube at these temperatures. It was later found that the manganese loss was considerably reduced by annealing these alloys in sealed quartz tubes containing one atmosphere of purified argon. As an added precaution the surface of each specimen was ground off before crushing the alloys to -270 mesh powder, using a hardened steel mortar and pestle. X-ray powder patterns were obtained using either FeKa or CrKa radiation in an asymmetrical focusing camera, which gave excellent dispersion of the closely spaced lines. Pictures were also obtained using a Debye camera of 5-cm radius which provided data in the angular region not covered by the focusing camera. The alloy specimens were polished and examined metallographically, using an etchant consisting of 60 pct glycerine, 20 pct nitric acid, and 20 pct hydrofluoric acid. The 10-g buttons were in each case broken in half and found to be well-melted and free of any gross segregation. One half of certain alloy buttons was submitted to chemical analysis in the "as-cast" condition. No appreciable change in composition seemed to occur during annealing . RESULTS The X-ray pattern of alloy Ti1.17Mn0.83 was found to agree well with that of the ternary R phase which was first found in the Mo-Cr-Co system,' and re-

Jan 1, 1962

By F. Maciosek, D. Denton, J. Johnson

Researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health and personnel from Coeur Silver Valley, Wallace, ID, conducted tests using rock strain strips and Split-Set rock bolts instrumented with strain gauges to monitor wall rock strain at the Galena Mine, Osburn, ID. The objective of the test was to identify whether strain on the rock bolts increased prior to a rock burst. Although results were inconclusive, researchers learned that the Split-Set rock bolts yielded in stick-slip fashion in the highly jointed walls of the stope. The bolts were also bent as stress was redistributed following blasting and subsequent movement along joints in the wall rocks.

Jan 1, 2004

By Laszlo Toth

A feeder is used to control the gravity flow of bulk solids from storage areas, like a bin or a stockpile. For this type of application, it is important to select a proper drive that can fulfill all of the demands put on it. High starting torque capacity, variable speed and the ability to handle frequent starts and stops are some of the demands that the drive must be able to meet. The following is a comparison of the most common type of drives used today for feeder applications. When a feeder is started, the breakaway torque may reach as high as200% of the running torque. The accelerating torque usually is set to protect the carrying element of the feeder, like the belt for the belt feeder and the carrying chain of the apron feeder (Fig. 1).

Jan 1, 2003

By B. Anderson, P. Churak, S. Dewar, A. Johnson, P. Eger

Although vegetation can be successfully established on fine taconite tailings, innovative approaches are needed to reclaim the coarse tailings used for dam construction. Through a series of cooperative projects with various government agencies and industries, EVTAC has been able to develop a unique closure plan. This plan will not only meet current reclamation standards, but also provide mitigation for a disturbed wetland and possibly create a tree plantation in the interior of the basin. By using waste products and exchanging materials, reclamation of the entire basin will be accomplised in a cost effective manner.

Jan 1, 2002

By K. I. Afewu

A modified approach to the implementation of Gy?s sampling theory is discussed and used to design a procedure for sampling crushed gold ore feed to metallurgical process plants. The approach involves calibration of certain ore-specific parameters. These parameters were calibrated for two different crushed gold ores en route to grinding mills in process plants. The model predictions were compared with the predictions from Gy?s original model. Far smaller masses of samples are required by the modified model than by Gy?s model at the same relative variance. The representativeness of the sampling procedure if normally distributed errors are assumed was also calculated. These procedures and evaluations lead to significant savings on cost of handling and preparation of the samples and to a quantifiable degree of confidence in the analytical results for the process plant.

Jan 1, 1998

By J. J. Scott

During 1967 wage settlements and strikes ran at a high rate and it has been estimated that union gains of 4 ½ % to 5% per year have been attained in many instances. When these events are coupled with the need to operate on lower grade and deeper deposits the need for technological advances in underground mining becomes obvious. Emphasis has been on ways to reduce the number of manshifts required per ton of product. Most significant advances have been made in rapid advance of primary mine openings, development of mobile, rubber-tired, front-end loaders and hauling units, high-speed drilling with rotary and rotary percussive units and a serious look at nuclear devices to break large volumes of ore cheaply. Boring Developments in bit manufacture and metallurgy have allowed continuous boring-type machines to be used on harder formations than was deemed feasible in the past. Hecla Mining Co. has been using raise boring equipment for drilling 9 7/8 in. diam pilot holes in raises which are later reamed in an upward direction to 48 in. diam. The machine used is a J. S. Robbins model 42R raise borer which has been used successfully to drill two relatively long 48-in. diam holes. The first was 520 ft in length at a dip of 76º, and the second was a 785-ft vertical hole.

Jan 2, 1968

By N. Katsikaros, A. Lewis-Gray, P. Richards

"To optimize gold recovery in complex leach-to-electrowinning processes, Gekko Systems developed the Gekko resin exchange column (G-REX) as an intermediate step, using a highly gold-selective resin to isolate contaminant metals. The AuRIX®100 resin produced by Purolite is licensed exclusively to Gekko, with the G-REX column designed specifically for this resin. Operational experience has been gained at the Castlemaine Goldfields Ballarat gold mine. In near-continuous operation since 2008, the Ballarat plant treats unclarified concentrate leach solution. The extension of this technology to higher throughputs and more complex chemistry is discussed.RÉSUMÉ Afin d’optimiser la récupération de l’or dans des procédés complexes impliquant la lixiviation suivie de l’extraction électrolytique, Gekko Systems a développé la colonne Gekko de résines échangeuses d’ions (G-REX) comme étape intermédiaire, à l’aide d’une résine hautement sélective pour la récupération de l’or qui permet d’isoler les métaux contaminants. Gekko détient la licence exclusive pour la résine AuRIX®100 produite par Purolite, et la colonne G-REX a été spécifiquement conçue pour cette résine. C’est à la mine d’or Ballarat de Castlemaine Goldfields que l’expérience opérationnelle a été acquise. L’usine de Ballarat, en exploitation quasi-continue depuis 2008, traite une solution concentrée non clarifiée de lixiviation. L’extension de cette technologie à des capacités supérieures et à une chimie plus complexe est examinée.AURIX®100 RESINAuRIX100 resin is a crosslinked polystyrene alkaline resin developed by Henkel (Virnig, Mackenzie, & Adamson, 1996). The resin beads are off-white in colour and spherical, with a nominal size of 100% +600 µm. This resin is highly selective for gold and silver over many metals, by way of extracting precious metal–cyanide complexes from leach solutions with a pH of less than 11.5. The higher end of the pH scale produces the best selectivity according to the order of preference: Au > Ag > Hg > Zn > Ni > Cu > Co > Fe. Purolite produces the resin and Gekko Systems maintains licensing of AuRIX100 resin for use in its G-REX column, as part of its unique suite of gravity gold–handling equipment.Significant cost savings over carbon-in-solution (CIS) systems are realized with AURIX100 resin: approximately 4–12% in capital savings and 27–40% in operating costs (Virnig, Mackenzie, Katsikaros, & Gray, 2004). Additionally, AuRIX100 resin is not susceptible to fouling; that is, the resin does not load with inorganic salts or organic compounds that would affect the loading and extraction of precious metals. To counter any potential for fouling by inorganic salts, a dilute acid wash is periodically conducted in service on the resin to unblock resin pores."

Jan 1, 2017

By Tim O’Neil

The search for precious metals opened up the American West. And Nevada was right in the heart of this development. In the mid-19th century, prospectors seeking gold roamed the hills of Nevada and discovered the ComstockLode. The development of this huge silver and gold deposit began in1859 and was responsible for Nevada’s early entry to statehood. Mining was Nevada’s first industry. In more recent years, the Nevada mining industry has led the nation in gold, silver and barite production. Nevada also produces many other minerals. These include aggregates, clays, copper, diatomite, dolomite, gypsum, lime and limestone, lithium and magnesium compounds, perlite, salt and silica. Even today, Nevada’s mining industry continues to be a major economic force in the state. The mining industry has made more than $10 billion in capital investments in Nevada since 1985. And the value of Nevada’s mineral production last year was about $2.7 billion.

Jan 1, 2000