Search Documents

By Eugie Kabwe

Rock bolts are components of tunnel support structures and their efficacy in reinforcement requires the appropriate estimation of the bolt pre-tension. However, cases of ineffective rock bolt application due to loosening are common which leads to the potential failure of the support structures, thus negatively affecting the tunnel stability. The effective employment of pre-tensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut pre-load. Henceforth, this paper presents a load indicator washer (LIW) capable of withstanding assigned static loading as well as provides an appropriate pre-tension. The different LIW breadths are numerically analysed in the finite element code (ABAQUS) to estimate deformation when a designated 60-kN pre-load is applied. The numerical simulation employs a bi-linear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nutLIW-rock bolt connection. Therefore, a long-term relaxation effect on bolt pre-tension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW-predetermined deformation is the bolt pre-tension. It is drawn from the simulation results that the 1.5-, 2.0-, 3.0-, 3.5-, and 4.0-mm-thick LIWs are completely flattened when subjected to 28-, 42.5-, 65-, 76-, and 88-kN pre-load respectively.

By A. R. Gaba

Phase I of the Canary Wharf development in London's docklands involves the construction of six fifteen storey buildings located predominantly over water of the West India Docks. The buildings are supported on some 1000 No., 25m long, open ended steel tubular piles driven through 10m of dock water to found in dense sand at a depth of about 15m below dock bed level. The piles are of composite section with reinforced concrete within the upper 17m of the steel tube. Three trial piles were installed in the dock to investigate the driveability and performance of the driven steel tubular piles. The piles were subjected to dynamic and static load testing. Loads were applied in both vertical and horizontal directions. Vibrating wire strain gauges were installed on the inside of the steel piles, on the reinforcement and in the concrete to determine the relative proportions of the applied load carried by the steel tube and concrete infill and to establish how these proportions varied along the length of the piles. Inclinometers were also installed to monitor the lateral deflection of the piles. This paper describes the driving, construction and testing of the three trial piles. The results of the vertical and horizontal loading tests are discussed and comparisons are made between dynamic and static tests carried out on the piles.

Jan 1, 1989

By Howard R. Pratt, Jimmie L. Bratton

The Air Force Weapons Laboratory (AFWL) has been carrying out a series of experiments whose principal purpose is to measure the dynamic response of rock media to large pressure pulses. Coupled with the field experiments have been theoretical calculations simulating this response. These two approaches allow an appraisal of the current ability to measure in-situ rock response under extreme conditions and also give a fair estimate of the current state-of-the-art in the area of computer calculation of the response of "real" geologic media to a large load. The area chosen for the test series is composed of a sequence of sedimentary units (shale, sandstone, and limestone) located in the Estancia Valley 45 miles east of Albuquerque, N.M. (Fig. 1). The units, which dip gently off the uplifted Manzano Mountains to the west, are essentially horizontal at the test site. An extensive geologic and geophysical investigation of the area was carried out in the form of surface mapping and seismic exploration. Numerous holes were cored and material properties were determined from tests of the cores. In-situ geophysical measure¬ments were also carried out. The experiment consisted of loading a 60X40 ft test area with a 4000-psi transient exponentially decaying pressure pulse. The pulse was initiated at one end and traveled the 60-ft length of the test bed. The test area was instrumented with acceleration, velocity, and strain measuring devices placed in drill holes to depths of 30 ft. Theoretical computer calculations of the response of the layered geologic media have been carried out on the AFWL CDC 6600 using one and

Jan 1, 1972

By Chengyi Ding, Xuewei Lv, Senwei Xuan, Chenguang Bai, Kai Tang, Gang Li

Sinter is an important iron-bearing material charged into blast furnace. Calcium ferrite (CF) is one of the most significant liquid phases in fluxed sinter. The isothermal reduction kinetics of CF and CF8M (n(CaO):n(Fe2O3) = 1, wt%(MgO) = 8) with 30% CO and 70% N2 gas mixtures at 1123, 1173, and 1223 K were investigated through thermogravimetric analysis in this study. Rate analysis illuminates that the reduction processes of CF and CF8M are mainly expressed as a typical two-stage reaction. Sharp analysis indicates that CF and CF8M reduction is expressed by the Avrami–Erofeev equation presenting a 2D shrinking layer reaction. The apparent activation energy values of CF and CF8M reduction are 46.9 and 31.8 kJ mol−1 individually based on model-free method.

Mar 1, 2018

By Arnis Mangolds

A study of the technical and economic feasibility of using a unique undercut and fill system developed by USBM engineers to mine steeply pitching coal is discussed. A brief resource assessment has indicated that significant reserves exist in most coal regions to justify the development of a safe and economical method of extracting steeply pitching coal. The undercut and fill system combines hydraulic coal cutting with unassisted gravity fluming of the coal slurry. Mining occurs across strike and the extended entry is backfilled to provide uniform strata control and an impermeable water and air barrier. Subsequent mining occurs beneath the previously filled stope such that the roof consists of a solid, controlled back. In addition to providing positive roof and hanging-wall support, the backfill system eliminates subsidence potential, post-mining drainage, and the danger of spontaneous combustion from naturally drafting air currents. A unique through-flowing ventilation system permits passage of return air through the production face via ducting located at the backfill-coal junction. This provides a constant supply of fresh air at the face, eliminates the need for brattice cloths, and provides an additional escapeway for the miners. The preliminary estimates indicate a production rate in the neighborhood of 31.9 tons/ manshift. Capital costs are approximately $3.17/raw ton over a 20-year life with an initial investment per annual ton of $48.29. Total cash-costs for labor, supplies, power and benefits range in the vicinity of $19.59 for a 704,460 ton/year mine, or a total cost of $22.76/ton. These costs do not include federal and local taxes or post-of-money; however, the cost of coal is well within the area selling price.

Jan 1, 1981

By W. J. Dick, K. G. Kress

A pipeline syphon can be a simple and reliable alternative for water conveyance as compared to otherwise more complex pumping systems or low-level outlet conduits through earthfill dams. In a simple form, it consists of a pipeline constructed over the top of a dam or other high topographic feature, connecting a source pond to a receiving pond or channel (Fig. 1). The syphon action is initiated by removing air from the pipeline (priming) using water pumps, vacuum trucks, or simple devices that can be purchased “off-the-shelf.” Once primed, the syphon flow rate can be controlled or stopped using conventional gate, valve, orifice plate, or other devices. Repriming is not required even if the flow is stopped, provided the syphon was not drained. A limiting factor in considering a pipeline syphon as a design option is the maximum lift (i.e. vertical distance from source pond water level to summit of pipeline syphon) which is approximately 9 m or less, depending on pipeline syphon features and site conditions. A pipeline syphon can be quickly constructed from readily available materials including steel, concrete, polyethylene, or PVC pipe. It is particularly well suited to many of the unique conditions often encountered at mine sites. This paper identifies situations that can sometimes be best resolved using a pipeline syphon. It provides basic principles for pipeline syphon design and includes case histories of their successful application.

Jan 1, 2005

1. Book review Respiratory protection - principles and applications by B. Ballantyne and P. H. Schwa be (Editors). London, Chapman Hall, 1981. (Reviewer: M. J. Martinson) 2. New manual Swedish steel manual, 1981. Available from Jernkontoret, P.O. Box 1721, S-I11 87 Stockholm, Sweden. SEK 85. 3. Publications of the Mineral Policy and Energy Sectors, Canada General review by L. Tibbo. 10 pp. Columbium (niobium) and tantalum by D. G. Fong. 6 pp. Sulphur by B. W. Boyd. 13 pp. Statistical summary of the mineral industry in Canada. 66 tables. Uranium by R. M. Williams. 16 pp. 4. Mintek reports Report 2126 The determination, by microwave techniques, of the interface between pulp and froth. Report 2129 An electrode controller for submerged-arc furnaces. Report 2131 The separation of trace elements in manganese dioxide. Report 2132 The assessment of pellicular anion-exchange resins for the determination of anions by ion chromatography. Report M2 The preparation of two reference materials of South African fluorspar. Report M3 The platinum-group minerals in the UG-2 Layer of the Bushveld Complex at Maandagshoek 254KT.

Jan 1, 1982

By Gerry Houlahan

The east span of the 3.5 km long SF-Oakland Bay Bridge is supported by different types of foundations along its span. Starting from the west, its first 460 m section comprising twin concrete box-girders is supported by sands and rock on Yerba Buena Island. A 620 m long steel suspension span then bridges a 25 m deep channel that is formed in sediments overlying rock. Twin concrete box girder structures, each 2.4 km long, complete the stretch over the remainder of San Francisco Bay to the engineered earth fill landing at its east end. For most of its length, the Skyway bridges water 3 to 10 m deep over soft surficial Young Bay Mud. The foundation types include spread footings with hold-downs, steel and concrete piles that are set in drilled rock sockets up to 3 m in diameter and 2.5 m diameter steel tubular piles driven to penetrations of up to 100 m. The design and construction-related considerations are presented. The different foundation types, influences of the site geology and earthquake demands on the substructures are discussed. The seismic motions of the bridge superstructures and substructures, as well as the depth-varying soil motions, influenced the foundation design. Together with performance-based design criteria, including post-earthquake footing displacement limits, these seismic demands influenced various aspects of the foundation design, including the use of battered and vertical piles.

Jan 1, 2005

ADDRESS BY THE PRESIDENT OF THE INSTITUTE (MR. J. G. SYMONS) IN PRESENTING THE MEDAL TO LAURENCE CHARLES BRODlE-HALL, C.M.G.The Institute Medal is awarded to a select band of people who have rendered great service to the mining industry and the community. Tonight it is my privilege to present the 1976 Institute Medal to one of our members, Mr L. C. Brodie-Hall, C.M.G.Laurence Charles Brodie-Hall, as chief executive in Western Australia for Western Mining Corporation Limited (WMC) from 1958 to his retirement in 1975, had a profound influence on the company's growth and development which had a significant influence on the prosperity of the State of Western Australia and, in turn, Australia.Following the company's decision in 1952 to diversify from gold mining, he took a leading part in the exploration and development of the bauxite deposits in the Darling Ranges by a subsidiary company, Western Aluminium N.L., and the subsequent formation of Alcoa of Australia Limited, the development of the first long term export contract for iron ore from Western Australia, the development of the nickel deposits at Kambalda and the subsequent establishment of a nickel refinery and nickel smelter in Western Australia.

Jan 1, 1977

By Russell J. Miller

A high-pressure intensifier system was designed, constructed and field tested as part of a program to determining the feasibility of applying high-pressure water jets on conventional mechanical rock excavation equipment to increase advance rates. Also developed were a high-volume swivel, capable of transferring the high-pressure water to a rotating cutterhead and manifold system for locating and protecting the jets on the cutterhead. Field tests were conducted in a granite quarry near Skykomish, WA, approximately 90 miles east of Seattle. The concept of improving excavation rates by using water jets to assist mechanical cutting was proven to be successful, with an average increase in excavation mete of 50 to 60%. For some tests, the excavation rate was more than doubled. Machine torque requirements were reduced approximately 25% when the water jets were used. It was suggested this was due to reduced cutterhead friction in the presence of the water jets. A comprehensive economic analysis was undertaken as part of a concurrent study to determine the degree of cost benefits attainable from increased advance rates. Very significant savings were seen to be possible. It was concluded that the basic concept of combining a water jet capability with a mechanical excavating machine is definitely possible.

Jan 1, 1976

By J. D. Davis

THIS REPORT gives results of an investi¬gation of the carbonizing properties of coals from Pittsburgh bed, Jamison No. 9 mine, Marion County, W. Va., and from Upper Freeport bed, Bull Run No. 1 mine, Preston County, W. Va. The study included Bureau of Mines-American Gas Association tests at 800° and 900° C. and various chemical and physical tests designed to evaluate the plastic, expanding, and agglutinating properties of coal. A blend of each coal was carbonized in the 500-pound slot oven. The carbonization sample of Pittsburgh coal contained 2.7 percent moisture, 35.8 percent volatile matter, 54.4 percent fixed carbon, 7.1 percent ash, and 0.9 percent sulfur. It contained 60.9 percent fixed carbon on the dry, mineral-matter-free basis and had a heating value of 14,780 B. t. u. per pound on the moist, mineral-matter-free basis. It therefore ranks as high-volatile A bituminous and was blended with low-volatile Pocahontas No. 3 coal. Upper Freeport coal contained 2.8 percent moisture, 27.7 percent volatile matter, 60.9 percent fixed carbon, 8.6 percent ash, and 1.0 percent sulfur, as carbonized. It contained 69.5 percent fixed carbon on the dry, mineral-matter-free basis and therefore ranks as medium-volatile bituminous. It was blended with high-volatile A Pittsburgh coal from Allegheny County Pa.

Jan 1, 1952

By B. Samanta

LHD (load haul dumper) is now used as a loading machine for intermediate mechanization in underground coal mining. For survival in the intense competition in the global business environment in recent years it is essential that LHD machine should be reliable and maintained effectively and efficiently. This paper seeks to study the reliability, availability and maintainability (RAM)of an LHD machine with failure and repair data by Markov modelling. The constraints and reasons for machine unavailability are outlined. The reliability and maintainability of an LHD and its subsystems are evaluated. Possible modification or design alternatives are highlighted. Reliability and maintainability of an LHD system are disappointing. There is room to take decisions on optimal maintenance planning and machine improvement from this analysis. Keywords: reliability, availability, maintainability, Markov model, LHD

Jan 1, 2004

New developments in the pipe conveyor and belt are advanced to address the growth in the capacity, length and complexity of pipe conveyor systems. Improved belt construction can offer better stability during horizontal curves and resistance to twist. Low rolling resistance rubber compound can significantly lower the power consumption and belt tension, producing capital and operation cost savings. Dynamic analysis, when used to analyze the conveyor?s starting and stopping behavior, can improve the design and reliability of long overland pipe conveyor systems. For these three aspects, technical backgrounds and field installations as examples are discussed in this paper.

Jan 1, 2012

By T. D. Mailula

Paper written on project work carried out in partial fulfilment of M.Sc.(Chemical Engineering) degree Chromite and talc are two major gangue minerals in platinum bearing UG2 ore processed from the Bushveld Complex in South Africa. During flotation, talc is effectively depressed by the addition of depressants. Chromite, on the other hand, is considered to be hydrophilic, its recovery is believed to follow water recovery and therefore recovered by entrainment only. In certain cases it has been shown that chromite can be activated by the reagent suite and hence is made amenable to true flotation. The aim of the work was to investigate the effect of the addition of copper sulphate as an activator and the effect of the depressant type and dosage on the recovery of chromite. The results of these experiments showed that copper sulphate, at higher dosages, activated the chromite. Low dosages of copper sulphate resulted in no chromite activation. This was observed at low depressant dosages of both IMP4 (guar gum) and KU5 (carboxymethyl cellulose (CMC)). When the depressant dosages were increased, at higher copper sulphate dosages, it was observed that the activated chromite was depressed by IMP4, but that the activation was still significant with the use of KU5. The activation of the chromite is attributed to the form of the copper species present in the solution and on the mineral surfaces at pH = 9 enhancing collector adsorption and thereby increasing hydrophobicity. These species were not measured directly and it is recommended that this should be further investigated using surface mineral techniques. Keywords: flotation; depressants; chromite; copper sulphate

Jan 1, 2003

By Tracy Brettmann

In recent years the Augered Cast-In-Place (ACIP) Pile industry has seen a substantial increase in the quality control options available to Contractors, Engineers, and Owners. Quality control methods range from the simple, manual techniques that have been used for years to new computerized installation monitoring equipment and nondestructive testing methods. Our ability to monitor and test ACIP piles has grown to such a degree that the industry is struggling to determine how much quality control is enough. This paper reviews the many options available and describes the pros and cons of each. The various nondestructive testing methods, in particular, have been difficult to apply reliably due to misapplications of methods and misinterpretation of the results. ACIP piles have unique properties that require the various nondestructive testing methods available be considered very carefully in determining the method most appropriate for a particular use. Some nondestructive testing methods, as well as automated monitoring equipment, potentially can be applied effectively to increase the level of quality control for ACIP piles. The experience gained on real projects using these new methods, in conjunction with the old procedures, provides valuable information for future applications.

Jan 1, 2000

Ferruginous manganese deposits have been known at Ripon Hills since the late 1950s. The main group of deposits occur in an area 6 km by 5 km and these were extensively investigated by Longreach Metals N.L. during1971 and 1972 for possible commercial exploitation.Ripon Hills is a dissectcd fault plateau 350 m above sea level formed by the uplift of a block of gently dipping Proterozoic shales, cherts, and dolomite. The plateau consists of chert breccia which is underlain by massive dolomite. The shales which are ferruginous and manganiferous overlie the chert breccia but are now only preserved, in places, in the broad depression and valleys of the plateau.The ore deposits occur as supergene replacement of the shales and were investigated by geological mapping, grid percussion and diamond drilling, and bulk beneficiation testing. Iron and manganese oxides erraticallyreplace Shale accompanied by the leaching of other minerals. The ore is composed of fine grained pyrolusite intergrown with fine grained hematite and locally containing extensively altered bixbyite and braunite. Thegangue mineral is mainly kaolin.The average grade, using a 15 per cent Mn cutoff, was 19 4 per cent Mn and 25·9 per cent Fe for a combined drill-proven, indicated, and inferred tonnage of 56,000,000 tonnes. The average depth of this mineralization from the surface is 11 m. Using a cutoff grade of 20 per cent Mn the average grade was 24·6 per cent Mn and 23·0 per cent Fe for a combined tonnage of 12,000,000 tonnes to an average depth of 8 m.The substantial drop in reserves occurs because a high proportion of the mineralized material contains less than 20 per cent Mn.It was shown that whereas the lower grade ore, despite erratic fluctuations in grade, could be beneficiated to specification grade by crushing, screening, and conductivity ore sorting, the higher grade ore could be beneficiatedto specification grade by crushing and screening only. The utilization of the higher grade ore was considered to constitute a more viable operation.There is potential for high grade manganese ore to be discovered in the Ripon Hills area at the contact of chert breccia and underlying dolomite.

Jan 1, 1977

By Ting Ren, Jon Roberts, Zhongbei Li, Ming Qiao, Jianming Wu

Spontaneous heating of coal continues to present a health and safety hazard in underground coal mines. The influence of seam gas composition on gas flow dynamics and distribution characteristics in the active longwall goaf has not been studied in-depth, and corresponding effective proactive goaf inertization strategies for preventing potential spontaneous heating from occurring have limited investigation. To advance this knowledge, an 80-m-height goaf model was constructed and developed based on specific conditions of an Australian underground coal mine, and onsite gas monitoring data was collated to verify base model results, which allowed for various scenarios of seam gas composition to be simulated and investigated with confidence. This study involved modeling five different gas composition scenarios for the goaf atmosphere, namely, 100% CO2 (case 1), 80% CO2 and 20% CH4 (case 2), 50% CO2 and 50% CH4 (case 3), 20% CO2 and 80% CH4 (case 4), and 100% CH4 (case 5). Simulation results show that O2 is primarily distributed at the middle and upper part of the CO2- dominant goaf model, while it is mainly layered at the floor level of the CH4- dominant goaf model. N2 is superior to CO2 in the goaf inertization for the CO2- dominant goaf model, whereas CO2 performs better than N2 for the CH4- dominant goaf model. The optimal inert gas flowrates for case 1 to case 5 are 1.5, 1.75, 0.75, 0.5, and 1.0 m3/ s, and the oxidation zone area is reduced by 55.76%, 67.21%, 58.04%, 78.17%, and 81.82%, respectively. The simulation results allow for increased insight and understanding of the gas distribution patterns in the active goaf with different seam gas composition and the development of corresponding proactive goaf inertization practices, thus minimizing potential spontaneous-heating-related hazards and improving mining safety.

Sep 26, 2023

By Philip L. Sibrell

A new process utilizing pulsed fluidized limestone beds was tested for the remediation of acid mine drainage at the Friendship Hill National Historic Site, in southwestern Pennsylvania. A 230 liter-per-minute treatment system was constructed and operated over a fourteen-month period from June 2000 through September 2001. Over this period of time, 50,000 metric tons of limestone were used to treat 50 million liters of water. The influent water pH was 2.5 and acidity was 1000 mg/L as CaCO3. Despite the high potential for armoring at the site, effluent pH during normal plant operation ranged from 5.7 to 7.8 and averaged 6.8. As a result of the high influent acidity, sufficient CO2 was generated and recycled to provide a net alkaline discharge with about 50 mg/L as CaCO3 alkalinity. Additions of commercial CO2 increased effluent alkalinity to as high as 300 mg/L, and could be a useful process management tool for transient high flows or acidities. Metal removal rates were 95% for aluminum (60 mg/L in influent), 50 to 90% for iron (Fe), depending on the ratio of ferrous to ferric iron, which varied seasonally (200 mg/L in influent), and <10% of manganese (Mn) (10 mg/L in influent). Ferrous iron and Mn removal was incomplete because of the high pH required for precipitation of these species. Iron removal could be improved by increased aeration following neutralization, and Mn removal could be effected by a post treatment passive settling/oxidation pond. Metal hydroxide sludges were settled in settling tanks, and then hauled from the site for aesthetic purposes. Over 450 metric tons of sludge were removed from the water over the life of the project. The dried sludge was tested by the Toxicity Characteristics Leaching Protocol (TCLP) and was found to be non-hazardous. Treatment costs were $43,000 per year and $1.08 per m3, but could be decreased to $22,000 and $0.51 per m3 by decreasing labor use and by on-site sludge handling. These results confirm the utility of the new process in treatment of acid impaired waters that were previously not amenable to low cost limestone treatment.

Jan 1, 2003

By Alex C. Smith, Thomas A. Gray, Lynn M. Crayne, Michael A. Trevits, Phil Glogowski

Mine fires constitute one of the greatest threats to the health and safety of those working in the underground environment and each event has the potential for disastrous consequences. Of the major mine fires and thermal events that have occurred in the United States in the last 6 years, it is estimated that remotely installed seals could have been used in 63% of the events to control fire growth or to aid in fire suppression work. The National Institute for Occupational Safety and Health (NIOSH) is conducting full-scale tests at the NIOSH Lake Lynn Experimental Mine to evaluate and improve remote mine seal construction technology. The main focus of this work is to develop reliable technology that will completely close the mine opening from floor-to-roof and rib-to-rib. This paper presents the results of remote seal installations using grout-based materials.

By Roy Peratrovich

An innovative cost-saving design for a 1,100 ft bulkhead on the Tanana River at Nenana in central Alaska won Alaska Construction & Oil magazine&apos;s Construction Achievement Award. The designers utilized materials available nearby at low cost. They planned sheet pile enclosures, self-anchored back into shore without cell closures. They made it practical for inexperienced local workers to do the building. And they completed the project on time and below a reduced budget.

Jan 1, 1985