Search Documents

By Thomas P. Mucho, David C. Oyler, Jim Pablic, Dennis R. Dolinar

A room and pillar coal operation in central Pennsylvania was experiencing roof cutters and long running roof falls caused by high horizontal stresses. The roof conditions created hazards for the miners, and caused several production panels to be abandoned prematurely. The mine requested assistance from the National Institute for Occupational Safety and Health (NIOSH) in applying the "advance and relieve" mining to reduce the affects of the horizontal stress during panel development. The "advance and relieve" plan that was developed called for removing a pillar on one side of the panel as it was being advanced, thus creating a cave. The caving then relieved a portion of the horizontal stress across the panel. Because the horizontal stress direction is key to the success of this method, stress mapping as well as mining experience was used to establish the direction of the horizontal stress. Subsequent field measurements provided an estimate of the stress magnitude. Three panels were mined using this technique, and good roof conditions were achieved in all these panels. Instrumentation was used to monitor the stress changes in the roof created by the cave. Stress relief of over 1,000 psi was measured 120 ft from the cave and to depths of 20 ft into the roof. The lateral extent of the stress relief zone across the panels appears to be about 400 to 500 ft. This case history has provided much insight into the practical application of the "advance and relieve" method discussed in this paper.

By M. A. van Nierop

The Discrete Element Method (DEM) is a model that is used to simulate the motion of the media in a grinding mill. The sum of the energy that is lost in inter-media and media-wall collisions represents the power drawn by the mill. The fact that the DEM predicts the power drawn by grinding mills over a large range of diameters has been used to show the validity of the DEM. However, the power drawn by a mill is a function only of the sum of forces of the load on the shell liners. A more accurate and detailed validation of the DEM would be to measure these forces as a function of angular position as the liner moves under the load, and to compare these measurements with predictions generated using the DEM. An experimental mill has been developed to reproduce exactly what the 2-dimensional DEM simulates. The 0,55 m diameter mill has a length of 0,023 m, which is fractionally larger than the diameter of the media used in the mill. One of the lifters in the mill has been instrumented so that the forces on the lifter can be measured as the mill rotates. The DEM simulation will be used to predict these forces. This will give experimental evidence of the validity of the DEM for modelling load behaviour in rotating grinding mills.

Jan 1, 1999

The Annual General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 27th August, 1969, at 4.15 p.m. Mr. R. C. J. Goode (President) was in the Chair. There were also present seventy Members, ten As¬sociate Members, two Affiliates, one Student and twelve Visitors making a total of ninety-five. The President declared the meeting open at 4.20 p.m. OBITUARIES The President: "It is my very sad duty to announce the deaths of the following members of the Institute: Mr James Charles Napoleon Humphreys, a Life Member who joined the Institute on 1st April, 1935, and passed away on 6th February, 1969. Mr Michael John Worrall, Graduate Member, who joined the Institute in 1960 and passed away on 2nd June, 1969. Mr Eric Adam Conrad Dickson, Associate Member, who joined the Institute on 13th June, 1952 and who passed away on 8th June, 1969. Mr Robert Jack, Associate Member, who joined the Institute on 2nd August, 1956, and passed away on 14th June, 1969. Mr R. A. H. Flugge-de-Smidt, Honorary Life Member and Gold Medallist, who joined the Institute in 1922 and passed away on 17th June, 1969. Mr John Gordon Craig, a Member who joined the Institute on 23rd August, 1960, and passed away on 6th August, 1969. As a mark of respect to the memory of the deceased, and in sympathy with the bereaved, I would ask you to rise and observe a few moments silence." MINUTES The President: "May we confirm the Minutes of the General Meeting held on 18th June, 1969, as published in the July, 1969, issue of the Journal?"-Agreed. WELCOME TO VISITORS The President: "We are honoured this afternoon by the presence of the Institute's Honorary President, Mr R. S. Cooke, President of the Chamber of Mines of South Africa, and by one of our Honorary Vice-Presidents, Mr T. L. Gibbs, the Government Mining Engineer, as well as by the presence of many distinguished guests, to all of whom I extend a most cordial welcome. We are happy to have present, Mr S. C. M. Naude, Director of the Witwatersrand Technical College, Mr G. A. P. Louw, Vice-President of the Associated Scientific and Technical Societies, Mr R. P. Randall, Senior Vice-President of the South African Institute of Electrical Engineers, Mr W. T. L. Wayman, President of the South African Institution of Mechanical Engineers, Mr D. F. Odendaal, President of the Institution of Certificated Mechanical and Electrical Engineers of South Africa, Mr E. Haacke, President of the Institute of Land Surveyors of the Transvaal, Mr B. L. Loffell, Vice-President of the South African Institution of Civil Engineers, Mr J. F. Leatherbarrow, President of the South African Institute of Assayers and Analysts, Dr W. S. Rapson, President of the Joint Council of the South African Scientific Societies, Dr P. L. Carman, President of the South African Chemical Institute, Mr F. Jackson, President of the Federation of Societies of Professional Engineers, Mr W. E. Kirkwood, President, S.E.I.F.S.A., Mr J. Steele, President of the South African Institute of Foundrymen, Mr M. Waite, President of the South African Institution of Welding, Mr M. R. Gericke, President of the South African Council of Professional Engineers, Mr G. C. Sowry, Chairman, Witbank-Middelburg Branch, Mr T. Groenewald, Chairman of the South African Chemical Institute (Southern Transvaal Section), Professor O. B. Volckman, Chairman of the South African Institution of Chemical Engineers, Mr H. W. Le Roux, Chairman of the South African Federation of University Engineer¬ing Students, Dr R. E. Robinson, Director of the National Institute for Metallurgy, Mr P. H. Anderson, Deputy-Chairman of Rand Mines Limited, Mr E. Boden, Manager of the A.S. and T.S. and Count Folchi-Vici, from Italy, who has lime interests in this country. I also extend a very special welcome to the lady guests here this afternoon, and to all the visitors." MEMBERSHIP The President: "I have pleasure in announcing that the names of the following candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership in the following grades: NEW APPLICATIONS Members: Stuart Denston Hill, Robert Roy Richardson, Gert Paulus van der Vyver. Affiliates: Henry Clifford Read, Allen Edward Hooper, Alan Edwin Edkins. Graduates: Lester Winston Sturgess, Erroll Vincent Bosman. Students: Terence Vernon van Heerden, David Curtis Lindley. MEMBERS TRANSFERRED TO A HIGHER GRADE From Associate Member to Member: Andries Willem van Zyl, Roy Lardner, Nugent Gerald Ward Comyn. From Student to Graduate: Michael John Worrell (now passed away), Peter John Hamilton Short. I wish to welcome the new members to the Institute, and to congratulate those members who have been transferred to a higher grade." ANNUAL REPORT OF THE COUNCIL AND ACCOUNTS FOR THE YEAR ENDED 30th JUNE, 1969 The President: "Ladies and gentlemen, It is with much pleasure that I present to you the Annual Report and Accounts for the year ended 30th June, 1969. These have been laid on the chairs and before calling for their adoption I would like to make a few comments. The Accounts show an excess of expenditure over income of R2,124 and our Honorary Treasurer, Mr D. G. Maxwell, will in due course comment on this. The main difficulty has again been the cost of the Journal and I think most of you are aware of the changes that we propose to make. I shall be sorry to see the last of our old format but then I have always had rather a con¬servative outlook.

By J. Van Steveninck, A. C. Pols, R. Feenstra

In the course of time, an increasing number of investigations on jet cutting all kinds of material, such as rock,1,2,3 metal,4,5 and wood6 have been reported to serve various applications. A number of papers have been published on these subject, 7,8,9 some of which refer to jets purposely containing abrasives, termed 'jetted particle drilling'.7 Since such abrasives complicate fluid handling considerably and do not appear to be absolutely necessary for making holes, only conventional drilling fluids have been considered. A large part of our investigation has been performed with the aid of three laboratory-type drilling machines, which permit tests on both micro-bits (1 ½ in. ) and full-scale bits (6 ½ -9 5/8 in. ) . In view of the application of jets in deep holes, care has been taken to simulate hydrostatic pressures as they exist in the field on the hole bottom. These have been found to have a major effect on the bit-penetration rate for various drilling fluids.

Jan 6, 1974

By K. A. Lewandowski

The efficiency of heap leaching is reduced by poor solution flow characteristics (i.e., channeling and ponding) that result from fines migration. Agglomeration of the ore can immobilize fines, but for agglomeration to be successful in copper leaching, an acid-resistant binder is needed to stabilize the agglomerates. Until now, there has not been a satisfactory method to evaluate whether a binder was effective, other than squeezing a handful to see if it ?feels right.? This paper reports on several procedures that have been developed to quantitatively determine whether a binder gives good performance in an acidic solution. These procedures have been used to identify binders that would be suitable for copper heap leaching.

Jan 1, 2008

By Tai Luu, Maxim C. Schisler, Yaser Taheri

The Stevens Gateway Project is an expansion of the Stevens Institute campus overlooking the Hudson River in Hoboken, NJ. The plans call for 90,000 ft2 (8360 m2) of new classroom, research, and student life facilities in new, 4-story buildings. The excavations for the building footprints were bounded by city streets and existing buildings, including the historic Carnegie Laboratory of Engineering, built in 1902. Pit underpinning was originally specified for the Carnegie building. However, given the depth of cut, construction time required for the 13 ft (4.9 m) deep pits would be substantial. The geotechnical contractor retained for the support of excavation work therefore offered an innovative active soil nail wall design that would meet project requirements in a shorter timeframe. Unlike the passive soil nail systems common in the industry that are chiefly used for soil slope stabilization, active soil nail walls contain pre-stressed anchor components to resist soil movement and limit settlement of soil and structures being contained. In addition to a discussion of the overall design approach of the active soil nail wall system, this paper will include a detailed description of its constructability and effectiveness. This project’s use of a conventional slope stabilization technique for an unconventional purpose may have positive implications going forward. INTRODUCTION Stevens Institute of Technology is a private university in Hoboken, New Jersey that sits on the cliffs of the City of Hoboken overlooking the Hudson River and Manhattan Island to the east of the campus. In recent years, the university has executed numerous plans to expand and upgrade its campus academic, student life, and residential facilities. One such project is the Academic Gateway Complex. The plan adds 90,000 ft2 (8360 m2) of new classroom, research, and residential facilities while also enhancing community connections by building a park to serve as a green corridor for the city. The proposed construction took place on the north and south side of 6th Street between Hudson Street and River Street. The project included the demolition of an existing university building followed by the construction of two, 4-story buildings on the north and south property lots. The north and south buildings will be connected by a second floor bridge spanning 6th Street. The buildings each contain a full basement extending from the proposed ground floor at approximately El. 41ft (12.5 m) to the basement subgrade at El. 26 ft (7.9 m). Each building will be constructed on respective mat foundations. Figure 1 presents an overview of the project area.

Jan 1, 2019

[Trans. No. Place Date Vol. Page 1. Wilkes-Barre, Pa.* May, '71.. 1 3 2. Bethlehem. Pa Aug., '71.. 1 10 8. Troy, N. Y Nov., '71.. 1 1S 4. Philadelphia, PaFeb., '72.. 117 5. New York, N. Y.*May: '78.. 120 5. Pittsburgh, PaOct., '72.. 125 7. Boston, MassFeb., '78.. 128 8. Philadelphia, Pa.* May, '78.. 2 3 9. Easton, POct., '78.. 27 10. New York. N. YFeb.. '74.. 2 11]

Jan 1, 1946

The theme of this Conference is 'The Future of Mining in New Zealand' to be addressed at a time of deepening economic concern. To ensure the assessment and development of our mineral resources in a competitive, safe and environmentally acceptable way a modest supply of a rare commodity û the professional mining engineer û must be assured. This paper briefly' reviews the history of mining education in New Zealand, discusses relevant overseas academic concerns and actions and discusses recent local trends which have led to a most serious recruitment position in the Department of Mining Engineering at the University of Auckland. Conclusions are drawn and proposals made which may remedy this situation which could have serious economic and sociological consequences for New Zealand.

Jan 1, 1991

By S Jackson, I Arbuthnot

The use of High Rate Thickeners has gained wide acceptance in the mineral treatment industries. The design of these units is characterized by an efficient deaeration and flocculation chamber, and introduction of the flocculated feed solids into a preformed floc bed zone. By these means the settling process is accelerated and consequently High Rate Thickeners achieve a significantly higher throughput per unit area than conventional thickeners.   The object of a control system on a High Rate Thickener (HRT), as on a conventional thickener, is to obtain the required underflow density and overflow clarity at all feed conditions. The feed conditions which may vary include volumetric and mass feed rate, pulp density, particle size and particle type. A conventional thickener has a large volume and cross sectional area, and changes in performance occur slowly û the operator has time to observe and react to these changes to maintain control. On a HRT, there is a much reduced residence time and therefore control parameters need to be reset more frequently. Although manual control is possible, the use of automatic control systems is therefore desirable to avoid excessive operator attention, while optimizing control of density and clarity. Automatic control of a conventional thickener is usually achieved by an underflow density loop which regulates the rate of withdrawal of underflow. A turbidity meter is sometimes used to measure overflow clarity and regulate the addition of a coagulant or polymer flocculant. These measures are not adequate on a HRT, because they would not give optimum control and could lead to excessive flocculant use. To achieve optimum operation in a HRT, the floc bed level should be maintained above the feed inlet point in the thickener. This bed level has become the key variable around which most control systems have been designed. However, a number of problems have occurred which has resulted in poor control, or only partial control of thickener performance. We will describe some of these problems, and a solution which is simple and effective.

Jan 1, 1990

By E. Douglas, V. M. Malhotra

"This report presents the results of a laboratory study undertaken to evaluate ground granulated blast-furnace slag from Algoma Steel Corporation, as a replacement for Portland cement in cemented mine backfill. The evaluation was based on the results of compressive strength tests performed on cylinders cast from mixtures made with a granulated blast-furnace slag and tailings from four different mines in the Sudbury basin. Various percent¬ages of slags and various binder to tailings ratios were used.Tests results show that, in terms of compressive strength, the slag performs as well or better than Portland cement as the binding agent in cemented mine backfill. Lime was found to be a poten¬tially good activator for ground granulated slag in mine backfill applications.A field test was conducted at one of the mines, consisting of placing a mixture of 95.5% ground granulated slag and 0.5% lime into a stope, and inspecting the floor slab as it hardened. The slag performed as expected, considering the backfill mixture proportions used and the preparation of the test site."

Jan 1, 1989

By Larman J. Heath

Wellbore enlargement was tested using hydrazine hydrate in a gas-storage well in Ohio to increase the well productivity. The wellbore was to be enlarged by chemical disaggregation of the sandstone adjacent to the wellbore. Productivity immediately declined 49.1 percent and gradually declined to zero in 7 months. A down-hole camera survey showed a white-to-gray precipitate covering the entire wellbore surface. The precipitate was chemically analyzed and identified as mostly carbazic acid, a hydrazine derivative of carbonic acid. Formation of this precipitate was not anticipated; this viscous sub-stance caused the gradual loss in productivity of the well. The wellbore was not enlarged. Laboratory tests were run to determine what clay stabilization measures could be taken in sandstone cores to prevent clay swelling and particle migration caused by hydrazine hydrate. Normal clay stabilization methods did not prevent the virtually complete loss in permeability to hydrazine hydrate. Other laboratory tests using natural gas diluted with small amounts of carbon dioxide confirmed the ease with which carbazic acid could be formed in a hydrazine hydrate-saturated environment within and adjacent to the wellbore.

Jan 1, 1970

Direct reduced iron (DRI), produced by the reaction between iron ore and reducing gasses, is used as a source of low-residual iron, in addition to ferrous scrap and pig iron, in the production of steel mainly through the electric arc furnace (EAF) route of steelmaking. The main DRI technologies in use are those of Midrex and Hyl, but in recent years a myriad of newer processes emerged based on variations in feedstock, reducing agent and fuel sources. Since the beginning of the nineties, DRI has increasingly emerged as a cheaper, low-residual iron feedstock for EAFs, which have traditionally relied almost entirely on ferrous scrap feed. The main stimulus behind the interest in DRI has been the increasing popularity of the EAF and the ?mini-mill? set-up as the favoured steelmaking option compared to the traditional and much less flexible blast furnace/ basic oxygen converter. This, however, has been creating a problem with regard to availability of low-residual scrap, resulting in upward pressure on high quality scrap prices and leaving DRI, traditionally the ?expensive alternative?, as a much more competitive consideration. The second main determinant has been the increasing production efficiency of existing steel plants which, in the light of improvements such as continuous casting and near net shape casting, has been constraining the supply of low-residual domestic scrap, traditionally the prime source of EAF feed. The explosion of current and proposed DRI projects has been accentuating the mounting interest of global role-players in assuring the availability of reliable sources of low-residual iron units for the future, especially in cases where definitive competitive advantages exist with regard to proximity to primary sources of iron ore and fuel (gas or coal).

Jan 1, 1999

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House on Wednesday, 24th August, 1977. Dr M. D. G. Salamon (President) was in the chair and declared the meeting open at 16h00. Obituaries The President: It is my sad duty to announce the death of the following members of the Institute : C. G. Evans, J. P. Rees, Life Fellows ; S. R. Bryant, H. MacConachie, M. Mrost, and A. W. van Zyl, Fellows; L. T. Campbell-Pitt, F. W. Collins, A. J. Duncan, I. G. Evans, F. W. Kleinschmidt, P. L. Vaughan, R. W. Wallace, and H. Wason, Members. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I would ask you to rise and observe a few moments' silence. Minutes The President: May we confirm the minutes of the General Meeting held on 23rd March, 1977, as published in the June issue of the Journal? Agreed.

Jan 1, 1978

Precast prestressed concrete piles designed to be end-bearing in a sand stratum at Drax Power Station met with extremely variable resistance during driving. Some piles came to virtual refusal almost immediately on entering the sand whereas others were driven to considerable penetration with very low resistance. Redriving and load tests on piles experiencing low resistance on initial drive showed that take up in strength occurred over a relatively short period of time. Investigations involving the use of pneumatic piezometers revealed the development of significant excess pore pressures during driving. Samples from boreholes showed that piles met the least resistance when the sand had a high silt content. Comparison with the original site investigation data demonstrated the difficulties in predicting detailed pile behaviour. The varied behaviour could not be related to the original borehole logs or to SPT or static cone penetrometer results. The factors controlling pile driving behaviour were essentially geological and could only be explained with reference to local soil grading.

Jan 1, 1989

By C. R. Copeland

Airborne dust emission standards are receiving growing attention. This trend is motivated by significant health studies that have shown adverse health effects due to exposure to dust. Currently, the air quality standards are not specific to particles in the nanoparticulate range (<1,000 nm). However, as our understanding of health related matters increases, it is very likely that nanoparticulate standards will be adopted. It was previously believed that typical comminution and material-handling practices could not result in airborne nanoparticulates. However, experimental studies using air monitoring and SEM have verified the presence of nanoparticulates in the air as a result of comminution and material handling. This means that emerging nanoparticulate air quality standards are a real possibility for industrial operations. With this emerging problem facing the minerals industry, effective suppression methods for nanoparticulates should be explored. Systematic studies have indicated that nanoparticulates from silica can be suppressed utilizing hygroscopic reagents such as calcium chloride. This reagent was as much as 93% more effective than water in suppressing silica nanoparticulates.

Jan 1, 2007

US 4,152,143-Continuous precipitation of cement copper from an aqueous ore leach solution mixed with pieces of iron as the precipitant Copper depositing on the pieces of iron is loosened and removed therefrom by means of constant but regulated oscillating movement of the pieces of iron in a horizontal elongated chamber, and the loosened copper is separated and collected from the mixture E Kausel and R Nissen, assigned to Klockner-Humboldt-Deutz A G May 1, 1979 8 pp (75-100) Filed 1-12-78 (868,981) (Drawings below) [ ] US 4,156,711-Removal of metal impurities from an acidic zinc or cadmium solution prior to electrolysis. Impurities such as manganese, cobalt, nickel, and thallium are selectively precipitated by contacting the solution with persulfuric acid or an ammonium or alkali metal salt thereof while maintaining a pH value of from 1 5 to 4 5 This patent is a continuation-in-

Jan 1, 1980

The Bureau of Mines is active in programs pertaining to solid waste disposal and land reclamation. Nine reclamation projects of mining companies and six projects of the Commonwealth of Pennsylvania were investigated to provide information on the procedures, costs, and results obtained from reclamation projects of bituminous coal-waste disposal areas. Refuse disposal costs of mining companies ranged from 9 to 28 cents per ton-mile, and quantities disposed of ranged from 600 to 4,500 tons per day. Spreading and compacting the refuse at the dump site ranged from 3 to 20 cents per ton. Cost of covering with soil and planting ranged from $750 to $1,646 per acre. Total costs of reclamation for the Pennsylvania projects ranged from about $1,800 to more than $15,000 per acre. Refuse preparation costs ranged from $772 to $5,550 per acre. Soil covering and planting costs ranged from $1,083 to $5,086 per acre. The best results were obtained by soil preparation and conditioning prior to planting. The type and depth of soil and effect of climate were also factors.

Jan 1, 1973

By M. Hooman, W. M. Marx, R. C. W. Webber-Youngman

This paper discusses a study that investigated different underground bulk air heat exchanger (>100 m3/s) design criteria. A literature review found that no single document exists covering all design criteria for different heat exchangers, and therefore the need was identified to generate a guideline with decision analyser steps to arrive at a technical specification. The study investigated the factors influencing heat exchanger designs (spray chambers, towers, and indirect-contact heat exchangers) and the technical requirements for each. The decision analysers can be used to generate optimized, user-friendly fit-for-purpose designs for bulk air heat exchangers (air cooler and heat rejection). The study was tested against a constructed air cooler and heat rejection unit at a copper mine1. It was concluded that the decision analysers were used successfully. This tool (decision analysers) can be used by engineers for the efficient and cost-effectively design of heat exchangers.

Jan 1, 2015

Paper presented at the UK minerals industry conference and published in: Minerals extraction towards the millennium. UK minerals industry conference, 3-5 April 1995, University of Leeds. London: Institution of Mining and Metallurgy, 1995. The various types of risks that arise in minerals industry projects are usually financial, technical, or environmental, and the key to valid risk analysis is complete integration of all risks, both within and between categories. Geographical information systems (GIS) and geostatistical simulation methods can provide a means of integrating data and conducting realistic risk analyses. Risk can be quantified but there are limitations to numerical approaches to risk assessment. Realistic quantification requires adequate models of the processes that give rise to risk. Risk perception must also be taken into account when conducting risk assessment and reporting the results, especially in public forums. The modelling and visualisation capabilities of a combined GIS/simulation system can provide the means of dealing with perception in risk analysis

Jun 19, 1905

By E. Fockedey

he destruction of free cyanide on a Co3O4 doped carbon felt was studied. The experiments were done with an eiectrochemical filter press cell on dilute alkaline solutions containing 250 mg/l NaCN. No chloride ions were added to the solutions. The cobalt oxide protects the felt against corrosion and has a catalytic effect on the degradation of the cyanide. This kind of electrode allows working with current density as high as 1200 Aim without any visible degradation of the felt. The most interesting results were obtained with a current density of 400 Aim&apos; at which the cyanide concentration can be lowered to 5 mg/l with a current efficiency of more than 70 % and a specific energy consumption of about 10 kWh/ kg CN.

Jan 1, 1998