Search Documents

By J. Noll, D. Yantek, B. Kendall, J. A. Organiscak

"A self-tramming remotely controlled mobile Dry Scrubber (DS) was developed by J. H. Fletcher and Co. under a contract with the National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research (NIOSH OMSHR) to reduce exposure of miners to airborne dust. NIOSH OMSHR laboratory testing showed that the DS averaged greater than 95% dust removal efficiency with the disposable filters and averaged 88% and 90%, respectively, for the optional washable filters in their pre-washed and post-washed test conditions. Although the washable filters could be reused, washing them generated personal and downstream respirable dust concentrations of 1.2 and 8.3 mg/m3, respectively, for a 10-minute washing period. The DS’s velocity pressure regulated variable frequency drive (VFD) fan maintained a relatively consistent airflow near the targeted 1.43 and 4.25 m3/s (3000 and 9000 ft3/min) airflow rates during most of the laboratory dust testing until reaching its maximum 60 Hz fan motor frequency or horsepower rating at 2610 Pa (10.5 in. w.g.) of filter differential pressure and 3.97 m3/s (8420 ft3/min) of scrubber airflow quantity. Laboratory sound level measurements of the DS also showed that the outlet side of the scrubber was noisier and the loaded filters increased sound levels as compared to clean filters at the same airflow quantities. With loaded filters the scrubber reached a 90 dB(A) sound level at 2.83 m3/s (6000 ft3/min) of scrubber airflow, indicating that miners should not be overexposed in relation to MSHA’s permissible exposure level (PEL) of 90 dB(A) at or below this airflow quantity (1). The DS’s washable filters were not used during field testing because of their lower respirable dust removal efficiency and the airborne dust generated from filter washing. Field testing the DS with the disposable filters at two underground coal mine sections showed that it can clean a portion of the section return air and provide about a 50% dust reduction at the face area downstream of the continuous miner (CM) operation. INTRODUCTION Coal mine worker overexposure to coal and quartz dust continues to be a problem at underground coal mining operations in the U.S. The U.S. Mine Safety and Health Administration (MSHA) recently changed the standard for coal mine worker respirable dust exposure from 2.0 mg/m3 average during an eight-hour shift to 1.5 mg/m3 average over the actual working shift, effective as of August 1, 2016 (1). If more than 0.1 mg/m3 quartz mass is found in the coal mine worker dust sample, the applicable respirable dust standard is further reduced to the quotient of 10 divided by the percentage of the quartz in the sample (1). Over 90% of the mechanized mining units operating in U.S. underground coal mines are continuous mining machines (2). MSHA inspector dust samples from 2009 to 2012 showed that 3.7% of continuous miner operators exceeded the 2.0 mg/m3 dust standard, while 8.8% of these dust samples exceeded the new 1.5 mg/m3 dust standard and 9.7% of these samples exceeded the reduced quartz standard (3). Additionally, roof bolter dust samples at these mechanized mining units during this same period have exceeded the 2.0 mg/m3, 1.5 mg/m3, and reduced quartz levels at 1.1%, 3.7%, and 10.6%, respectively (3)."

Jan 1, 2016

By Nan Hua

As a high production and high efficient mining method, top coal caving method is now widely used in China. However, as more extra-thick coal seams are mined, it becomes more and more difficult to make the top coal fully broken up, resulting in more and more top coals flowing into the gob, rather than onto the rear AFC at the working face as designed. This research is aimed to investigate the failure mechanisms of the extra-thick top coal caving mining method.

Jan 1, 2009

Owing to improvements in computer capacity, it is now possible to undertake fully coupled or partially coupled, three-dimensional (3D) hydromechanical Finite Element (FE) simulation of mines, including explicit representations of large numbers of discontinuities. The analysis requires fewer assumptions than uncoupled analysis or two-dimensional (2D) analysis, but may require a change in how hydrological data is collected. The way hydrological data is incorporated in stability assessment and the approach to uncertainty in hydrological information also requires discussion. The current procedures for this type of analysis are discussed, along with some practical difficulties and teachings from early applications. A work flow for integration of 3D hydromechanical modelling with pit planning and some considerations for the management of uncertain data are also proposed.

May 1, 2010

By R. P. Killmeyer, W. W. Wen, B. K. Parekh

A continuous pilot-scale test of the GranuFlow Process was conducted using a screen-bowl centrifuge for the dewatering and reconstitution of column -flotation concentrate at a coal preparation plant in Virginia. In this test, a slipstream of the fine clean-coal slurry from the column flotation con¬centrate was treated with a bitumen emulsion before dewatering. The treated products from the screen-bowl centrifuge appeared to be dry and in a free flowing granularform, while the untreated products were wet, sticky and difficult to handle. Test results indicated that the average moisture contents of the dewatered coal products were 35.7%, 35.5%, 32.6%, 29.9% and 26.5% (by weight) with Orimulsion additions of 0.0%, 0.7%, 3.2%, 4.8% and 6.4% (by weight), respectively. The handleability and dust reduction of the dewatered coal products were also vastly improved.

Jan 1, 2000

By G. L. Smith

Central to the success of any mining company is the ability to manage capital investment effectively so as to ensure acceptable stakeholder returns within an overall strategic context. Critical to this process is the effective selection and implementation of a strategically aligned project portfolio that enables optimal resource exploitation while operating within mandated bounds and identified constraints. Consideration is given to the strategic long-term planning process, an investment prioritization methodology and specific tools and techniques based on the discounted cash flow philosophy.

Jan 1, 2007

By K. M. Rolls, J. Wulff, D. A. Colling

Solid-solution alloys of the Ta- Ti system containing up to 70 at. pct Ti were melted and fabricated into wire. Steady magnetic-field measurements of cold-worked wires at 4.2°K indicate that the resistive critical field increases smoothly with increasing titanium, reaching a maximum of 93 kG (J = 1 amp per sq cm) for a composition of about 50 at. pct Ti. The composition dependence of the resistive critical field indicates it is largely paramagnetically limited for alloys containing more than 35 at. pct Ti. For cold-worked wires the value of the critical current density, Jc , was found to be insensitive to composition changes for compositions in excess of 20 at. pct Ti. It was observed that Jc could be increased by final-size heat treatment at 400°C without altering the value of- the resistive critical field. Experimental data are used to calculate the electronic specific-heat coefficient and the "upper critical field" for the alloys studied. THE effect and importance of metallurgical structure on superconducting properties have been summarized by Livingston and Schadler.1 Specific work on solid-solution alloys such as Nb-zr2-7 and Nb-Ti5-7 have shown that critical current density (Jc) and superconducting transition temperature are structure-sensitive. Berlincourt et al.6,8,9 in their studies of transition-metal alloys find that Ta-Ti alloys remain superconducting at fields comparable to Nb-Ti alloys. 6,8 Transverse critical current tests of a Ta-10 at. pct Ti alloy10 and longitudinal critical current tests of a Ta-25 at. pct Ti alloy1' indicate that such alloys are capable of carrying high currents at intermediate fields (-40 kG). The work reported in the present paper was undertaken to explore the superconducting properties of further compositions in the Ta-Ti alloy system as well as the structure sensitivity of the superconducting properties. I) EXPERIMENTAL PROCEDURE Alloys were prepared by melting tantalum (Fansteel Metallurgical Corp., 99.96 pct purity) and iodide, crystal bar titanium (Foote Mineral Co., 99.92 pct purity) mixtures in an arc furnace on a water-cooled copper hearth using a tungsten electrode. Melting was accomplished in a purified, gettered argon atmosphere at pressures from 250 to 400 Torr. Each alloy was turned and remelted fourteen times to assure complete mixing of tantalum and titanium. Ex- cessive coring in the cast samples was, nevertheless, observed. This was somewhat reduced by annealing in vacuo at 1000°C for 13 hr. The ingots were then machined to 0.250 in. diam, jacketed in Type 304 stainless-steel tubing, and swaged to 0.140 in. diam. They were then drawn to 0.010-in.-diam wire. Alloys containing up to 70 at. pct Ti were readily cold-drawn to wire in this manner. Later experiments showed that oxygen additions up to -3000 ppm could also be cold-worked into wire. Test samples for superconductivity measurements in the 2-in, air-core Bitter solenoids of the M.I.T. National Magnet Laboratory were prepared from 10-in. lengths of 0.010-in.-diam wire, cleaned of residual wire-drawing lubricant. Current contacts were made by clamping clean copper tubing over both No. 18 current lead wire and the ultrasonically indium-tinned ends of the specimen wire.12 Potential leads of No. 32 copper wire were connected to the specimen by ultrasonic soldering in an indium bath. The potential lead separation was about 4 cm, corresponding to the circumference of the Bakelite rod to which the wire was affixed with half-mil Teflon tape. The final specimen configuration is shown in Fig. 1. Specimens were lowered into a liquid helium bath (4.2oK) in a double solenoid dewar and positioned so that the maximum magnetic field was oriented transverse to the wire axis of the gage section. Measurements were made by passing a current through the specimen at a preset solenoidal magnetic field. The current was increased until a 1-pv potential difference appeared across the gage section (1/4 µv per cm). At low magnetic fields, however, it was not possible to use this criterion because power-dissipation difficul-

Jan 1, 1967

By N. P. Mahumapelo

This paper is based on a study to determine the potential beneficiation opportunities for marble from Griekwastad in the Northern Cape Province. The marble was characterized mineralogically by X-ray diffraction. Major and trace elements were determined using inductively coupled plasma-optical emission spectroscopy. The sample was crushed, and the crushed material beneficiated by tumbling and polishing. The resulting beads were incorporated into a variety of jewellery and other decorative items. It is concluded that the beneficiation of Griekwastad marble presents a good opportunity for value addition and job creation, provided that an effective marketing strategy for the products can be developed..

Jan 1, 2014

By Wang Jia, Chai Li-yuan, Zhang Jin-Long, Peng Bing, Zhang Qiang

"Electrolytic manganese dioxide (EMD) residue was mixed with shale and fly ash as the main materials to make solidification/sintering brick for the utilization of the residue from EMD production. The effects of sintering temperature, sintering time, solid waste content and cooling process on its mechanical properties and toxic elements solidification were investigated according to compressive strength and leaching toxicity. The results showed that the calcined residue had capability of solidifying toxic metals and exhibited perfect strength after treated in the optimal parameters of EMD residue below 50%, temperature at 1000-1100°C, time3-5h, and semi-quenched at 600°C1 InstructionSolid clay-brick holds the leading position among building materials for a very long time in China. The traditional technique of making clay-brick has the drawbacks of backward process, simple facilities and single product. Since Chinese Reform and Opening-up, urban-rural construction and real estate have been booming with the rapidly development of national economy and science technology. The problems of ruining fertile land, environment contamination and high energy consumption in the traditional technique of clay-brick making have not been solved yet. On the other hand, more than 7 billion tons of industrial wastes are accumulated over years which occupies over 6.7 million hectares filed and causes serious environmental problems[1-31. Strategy present in ""The Chinese Agenda of the 21st Century"" required the production of wall materials less energy conservation, land saving and waste recycling.Coal gangue[4-9l, fly ash[I0- 13l, sludge from waste water treatment and tailings of gypsum, pyrite, copper mine, high silicon containing iron, asbestos and ects [l4-lSJ are the solid wastes used for brick making around the world. There are two kinds of process for brick making, high temperature sintering and low temperature steam curing[19•201. Although the technology of two brick making made great progress and got widely application in construction field, no precedent for preparing sintering-bricks with EMD residue as materials occurred in China because of its complicated processing technics and lack of sufficient practical experience to guarantee the bricks' quality.In this study, EMD residue was mixed with shale and fly ash as the main materials to make solidification/sintering brick. The effects of sintering temperature, sintering time, solid waste content and cooling process on its mechanical properties and toxic elements solidification were investigated according to compressive strength and leaching toxicity."

Jan 1, 2011

By Todd M. Ruff

Blind areas around construction equipment are a major contributing factor in incidents involving a piece of equipment striking a worker. In highway construction, these types of incidents result in an average of 22 deaths a year in the United States. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health, in cooperation with the Washington State Department of Transportation, is evaluating methods to decrease these incidents. One such method uses devices that assist equipment operators in monitoring blind areas around the equipment to prevent collisions with workers or other objects. Several camera and sensor systems are available for this application. These systems were evaluated on various trucks used in road construction and maintenance. Tests were conducted on sanding trucks during the winter months, which allowed researchers to investigate the effectiveness and limitations of various technologies under the most extreme conditions. Tests were also conducted on dump trucks and utility vehicles during the warmer months to study the effectiveness of the systems in highway work zones. Results showed that many difficulties arise when using camera and sensor systems in cold, snowy climates. And, while the operation of these systems is more reliable during the warmer months, challenges still exist in using them on equipment in congested work areas.

By N. D. L. Burger

A low noise blast hole drilling system was developed to limit the risk of noise-induced hearing impairment in mining operations. Noise- induced hearing loss has been identified as a major occupational health risk in SA mines. The noise generated by pneumatic percussion drills is a major contributor to such noise-induced hearing loss. This motivated the South African Safety in Mines Research Advisory Committee (SIMRAC) to commission the development of a low noise rock drill system. The system had to be designed, manufactured, tested and demonstrated in a simulated underground mining environment. The specification required noise levels below 90 dBA. Other important design considerations were ease of manual transport, setting up and operation. The primary design concept was to encapsulate a standard SecoS215 pneumatic rock drill in a composite material tube. The tube is pushed onto the rock face by a pneumatic cylinder and is sealed at the rock face by an elastic seal. The drill is pulled towards the rock face by a rope and pulley mechanism fitted inside the tube. This mechanism is powered by a second pneumatic cylinder. The actions of moving and setting the drill require two persons. However, the team can carry out the drilling function itself on several drills simultaneously because of the self-thrusting design. The drill is supported by two camlocks. The exhaust (air containing dust, water, rock debris, oil and grease) is removed from the encapsulating tubes via an exhaust tube to the end of the stope. In this way exhaust noise and air pollutants are disposed of away from personnel. Tests were conducted in a test stope. Noise levels of under 90 dBA were achieved, thereby attaining the primary design specification. This was achieved without materially compromising ease of handling. Penetration rate was somewhat improved compared to that of the standard drill, so that productivity could be maintained. Keywords: Drill, rock drill, quiet, noise, mine, underground.

Jan 1, 2004

What is a nugget effect? In the early development of geostatistics, the term ?nugget effect? was coined for the apparent discontinuity at the beginning of many semivariogram graphs. This name was chosen to reflect the large differences found between neighbouring samples in ?nuggety? mineralizations such as Wits gold reefs. Geostatistical theory assumes that the difference between a sampled value and a potential repeat sample at the same location is actually zero. Included in this ?nugget effect? would be true variation between contiguous samples due to the nature of the mineralization, micro-fracturing, nugget or crystal size, and so on. Also included in the nugget effect would be any ?random? sampling variation which might occur due to the method in which the sample was taken, the adequacy of the sample size, the assaying process, etc. Arguments were put forward that ?sampling errors? actually exist at zero distance. Some geostatistical schools actually maintain that the ?nugget effect? is all sampling error. This would imply that ?perfect? sampling would eliminate the nugget effect entirely. There is now a dichotomy both in the geostatistical world and in the software packages provided for geostatistical analyses. It may seem academic to argue over whether the semivariogram model should take a value of zero, a value equal to the nugget effect, or a partial value at distance zero. However, the decision can have a profound effect on both the estimated resource and in our confidence on that resource. Whereas most geostatistical texts define the semivariogram model as taking the value of zero at zero distance, others imply that the full nugget effect should be used at zero distance. For example: ?The nugget effect refers to the nonzero intercept of the variogram and is an overall estimate of error caused by measurement inaccuracy and environmental variability occurring at fine enough scales to be unresolved by the sampling interval3 ?Christensen4 has shown that the ?nugget effect?, or non-zero variance at the origin of the sernivariogram, can be reproduced by a measurement error model ?The nugget effect is considered random noise and may represent short-scale variability, measurement error, sample rate, etc.5. In many training texts and Web courses, the definition of the semivariogram is ambiguous as the formulae for semivariogram models is not actually specified at zero distance6,7,8.

Jan 1, 2010

The Round Hill gold-scheelite deposit is located three kilometres from Macraes Flat and approximately 60 kilometres due north of Dunedin, New Zealand. A mining feasibility study is currently being undertaken on the deposit by BHP Minerals (New Zealand) Limited, who are the managers and operators of a Joint Venture with Home Reef Mining Limited. BHP has a 70 per cent equity in the project area.

Jan 1, 1987

By George A. Morgan

The successful expansion of crude oil production begun in late 1977, led to promising development of the nonfuel minerals sector. Although actual production of nonfuel minerals was limited both in variety and in percentage of output on a world scale, the potential for expansion with a rapidly developing infrastructure was significant. The energy base was expanding with construction of two new hydroelectric powerplants in addition to the existing plant near Edea. The Song Loulou plant will have a 240-megawatt capacity, and a hydroelectric plant under construction in the northern part of the country by mainland China will have 72 megawatts of installed capacity. Inflation of between 15% and 20% resulted in a real gross domestic product (GDP) of $2.8 billion2 in fiscal year 1980 (July 31 to June 1), up 6% from that of the previous fiscal year. Petroleum became the leading export item in terms of value, surpassing coffee and cocoa exports. Mineral exports as a whole increased eightfold in value, mainly because of oil sales. Oil exports also caused a reduction in the trade deficit by nearly one-third, and the Government expected its 1980-81 budget to be balanced at $1.17 billion. The Port of Douala accounted for about 8 million tons of cargo, or 93% of total maritime traffic for Cameroon. Expansion plans for the port call for an initial increase to 5 million tons, and a cargo handling capacity of 7.5 million tons in 1985 and 10 million tons by 1990. The Port of Victoria will gain importance with the startup of an oil refinery. The country's third seaport at Kribi was used solely for timber shipments, and capacity at the Port was to triple by 1981. The Government operated its own shipping line with six oceangoing freighters. France was the dominant trading partner, accounting for 25%

Jan 1, 1982

By Jan E. Nesset, Antonio DiFeo, James A. Finch, Jose Hernandez-Aguilar, Cesar O. Gomez

"The gas dispersion measurement sensors and methodology developed by the mineral processing group at McGill University have to-date been employed at a number of plants in Canada, Australia, the U.S., South Africa and South America. In some cases the measurements have been directly linked with metallurgical performance while in others the gas dispersion surveys on their own have proved very useful in understanding the behaviour of the flotation cells. In addition to reviewing the current state of the gas dispersion measurement technology, the paper will present a series of case studies from the various plants and will show how this technology brings a remarkable new level of understanding to flotation behaviour. The influence of the bubble size distribution on recovery and grade are emphasized in the paper.INTRODUCTIONBackgroundThe advent of new sensors to characterize gas dispersion parameters in flotation cells is a development that is long overdue. While the chemistry of flotation has been studied since the early 1900’s, it is only now that the significance of bubble size distribution, gas rate and gas holdup can be meaningfully measured in-plant with robust and precise sensors. Early researchers, like T.A. Rickard (1916) recognized the importance of understanding the role of air and bubbles in flotation when he wrote in 1916 “we know that the key to the flotation process is to be found not in the oil, the acid, or the apparatus, but in the bubbles. The man who understands the mystery of a soap bubble has mastered the chief mystery of flotation”. In his 1999 review paper on The Froth Flotation Century D.W. Fuerstenau laments the fact that due to their “inert nature”, bubbles have never received their due attention from researchers who tended to focus on the chemical, physical, surface and colloidal aspects, rather than the physics of the process. It is perhaps fitting that now, 100 years after the inception of industrial flotation practice at Broken Hill, Australia, researchers and industry have turned their attention toward the importance of truly understanding the role of bubbles in flotation."

Jan 1, 2005

By M. Sibanda

The diffusion of carbon in Co-5% Fe alloy was studied in a belt-type pressure system at temperatures of up to 1330°C and press loads or nominal pressures of 7 020 tons or 42±3 kbar. Under these conditions, this alloy is in the solid state. Discs of graphite and prealloyed Co-5%Fe were used to make up the diffusion couple. The diffusion coefficient increased with increasing press load due to the tendency of the low density graphite to dissolve in the metallic phase reducing the overall volume and increasing the density of the system. Furthermore, inhomogeneous plastic deformation may have promoted diffusion by creating defects in the alloy. Diffusion couples treated at atmospheric pressure exhibited graphite particles in the metal, while those treated at high pressures exhibited carbide in the form of Widmanstatten laths. Carbon analyses indicated increased carbon solubility with increasing pressure. This was confirmed from calculated high-pressure phase diagrams.

Jan 1, 2005

By Lucien Eaton

THE use of filling in mines is less common in the United States than it is in Europe, where in some places it is required by law. In most cases the filling is placed by hand, and the material used for this purpose is the waste from development and that sorted from the ore in the stopes. When these sources provide an insufficient supply, additional rock must be quarried on surface or mined underground, or some other material :st be used. In different parts of the world sand, clay, gravel, culm, nulated slag, mill tailings, and even ashes, have been used as filling material in place of or in conjunction with rock. Of all the materials used for filling the best is probably clean sand. Gravel, finely crushed rock, granulated slag and coarse mill tailings are almost as good, and the methods used for placing and confining sand will apply equally well to any of these. The advantages of sand are its comparatively slight compressibility and the ease, economy and convenience with which it may be placed. On account of the voids, which necessarily occur in fills made of coarse waste, such fills will compress 10 to 25 per cent before they develop their full strength, whereas clean sand seldom compresses more than 5 per cent. Sand is especially desirable when practically complete filling is required, and sand derived from mill tailings, especially when not thoroughly cleaned, has been remarkably effective in sealing off and extinguishing mine fires. When natural sand is available on surface, or when it can be obtained from the mill tailings or tailings dump, the cost of using this material for fill will probably be considerably less than that of rock. In this paper it is not proposed to discuss all methods of filling, butt to describe some of the methods used for placing sand fill and to make a brief comparison of their merits.

Jan 1, 1932

John P. Thomas, President. B. W. Snodgrass, Secretary-Treasurer. San Andrews, mine boss, Morley. Richard Bickerton, Tabasco. E. P. Bayles, superintendent, Cokedale. Clyde Campion, parting tender, Valdez. O. C. Cook, 406 East Seventh, Street, Trinidad. James Cameron, superintendent, Hastings. Charles Chambers, superintendent, ,Sopris. Arthur Dennison, Trinidad. Samuel Dean, mine inspector, Delagua. F. S. Dunlevy, assistant engineer, Hastings. L. R. Douglas, assistant engineer, care Danford & Sanderson, Trinidad. W. E. Danford, superintendent, Segundo. M. O. Danford, superintendent, Cedar Hill Coal & Coke Co., Trinidad. John Dougherty, mine foreman, Morley. J. C. Davidson, timberman, Valdez. William Easton, fire boss, Valdez. George Fortune, electrician, Primero. D. J. Griffiths, chief mine inspector, Trinidad. J. E. Hanes, assistant engineer, Hastings. Joseph Haske, superintendent, Primero. O. C. Erwin, electrician, 714 Pine Street, Trinidad. R. J. Jinkins, superintendent, Morley. Thomas jolly, superintendent, Gray Creek. James Jamieson, assistant mine boss, Valdez. James Kilpatrick, fire boss, Tobasco. L. M.. Kuhns, first-aid miner, care Mine Safety Car No. 2, Trinidad. William B. Lloyd, 404 East Seventh Street, Trinidad. J. C. Lawrence, machinist, Starkville. R. A. McAllister, mine inspector, Trinidad.

Jan 1, 1913

By I. Bock

Selective Blast Mining (SBM) makes use of milli-second sequential blasting technology to separate the valuable reef material from waste rock in the blasting operation at stope faces in the mining of tabular ore bodies such as exist in the gold and platinum mines in South Africa. The waste rock is cast blast to the back of the stoping area, and the reef material is fractured and deposited close to the stope face. Only the reef material is transported to the surface. A simplified economic model is presented to evaluate the economic benefits of SBM. Although premature, in that adequate experimental demonstration of the validity of the model has not yet been possible, the model is presented since it indicates substantial benefits in the case of narrow reef gold mines. It is suggested that many marginal mines should seriously consider SBM. Benefits can also be realised in platinum mines, but a lot more experimental work is necessary to establish cost parameters more reliably. Some practical experience in the use of SBM in the mining of the UG2 reef is presented.

Jan 1, 1998

By J. T. Hollow

The Fort Knox Mine is located in Alaska?s interior, where the average ambient air temperatures range from -24°C (-11°F) in January to 16°C (61°F) in July. The mill processes a free-milling gold ore utilizing both a gravity recovery circuit and conventional cyanide leach/carbon-in-pulp circuits. Mathematical models have been developed to accurately predict the impact of leach circuit slurry temperature on gold leaching, carbon adsorption and cyanide destruction kinetics. Additionally, an energy-balance approach has been used to model the seasonal variations in slurry temperatures throughout the Fort Knox mill. The energy-balance model, combined with the kinetics models previously developed to predict plant performance, was used to justify a tailing thickener installation at the Fort Knox Mine. This paper describes the development of the energy-balance model and its prediction of plant performance assuming a tailings wash thickener to reduce heat loss from the mill. Also presented is an analysis of the post-project plant performance that validates the model and shows that the mine produced an additional 596 kg (19,155 oz) of gold while reducing mill reagent costs by $6,302,000 during the first 38 months of operation.

Jan 1, 2007

By G. Deschênes

Following a successful investigation on the Central Zone sample, a cyanidation study was conducted on an ore sample from the AD-MW Zone of Clarence Stream Property, owned by Freewest Resources Canada, to develop a leaching strategy to extract gold. At a grade of 6.48 g/t, gold is present in the forms of aurostibite, free gold and electrum. The ore contains 4.3% berthierite/gudmundite, 1.3% pyrrhotite, 0.7% pyrite, 0.07% stibnite and 0.9% arsenopyrite. Similar to the Central Zone, the extraction of gold from the AD-MW Zone can be performed at atmospheric pressure, pH 10.5 and with a low concentration of cyanide. The grind size had no effect on gold extraction between a P80 of 28 to 71 µm. The oxygen and cyanide requirement significantly increased with a ?ner grind. Consequently, a very close control of cyanide addition is required to minimize passivation of gold. Lead nitrate, added in the pretreatment, increased the extraction of gold by 2.3%. Leaching at pH < 10 improved gold extraction but increased the cyanide consumption by 5%. Passivation of gold occurred when the pretreatment was longer than 2 hours. A longer pretreatment reduced the cyanide consumption by 5%. Mineralogical characterization of the leach residue with no gravity pretreatment prior to leaching indicated the presence of unleached gold grains and passivated gold grains. Removal of coarse gold by gravity increased the extraction by 2.8% (leach residue at 0.74 g/t Au). Increasing the DO to 16 ppm or the lead nitrate from 500 to 1,000 g/t increased the overall gold extraction to 90.4% (leach residue at 0.62 g/t), which is the maximum gold extraction obtained. The leaching parameters were 800 ppm NaCN, DO 16 ppm and pH 10.5 for a duration of 120 hours. The associated cyanide consumption was 4.0 kg/t. Gold leaching was not sensitive to cyanide concentration. Reducing the cyanide concentration to 250 ppm resulted in a gold extraction of 89.5% with a cyanide consumption of 2.6 kg/t.

Jan 1, 2009