Search Documents

The principles of geometry and trigonometry are so continuously used by mining engineers for the purpose of accurately and intelligibly recording their measurements, that the writer is prompted to lay the following cursory remarks upon mine surveying before the members of this Institution in the hope of eliciting a free interchange of opinion upon details of this interesting branch of the profession. He proposes to deal with surveying only so far as it concerns the mining engineer, not to intrude upon the domain of the professional surveyor, and, in this instance, to discuss more especially that which may be termed the mechanical, rather than the mathematical side of surveying.In the latter part of the eighteenth century and the beginning of the present one, the usual underground surveying equipment in the English metalliferous mines, consisted of a magnetic needle in a fiat square wooden box of about 9-inch sides, a two-foot rule, a long cord, aud a stool, upon which to place the needle and box. The operator took his bearing by sending his assistant with the end of the cord as far in a straight line as the length of the cord would admit.On its being drawn that he held its end in one hand and placed the side of the compass-box against it with the other, and noted the bearing thus found either by a book entry, or by ticking it off with a piece of chalk on the board the compass lay in. He then measured the cord with a two-foot rule. It is needles to say that with these appliances the accuracy of the results were open to question, and mining surveying was not unduly popular.In the present day, engineers have the advantage of using instruments brought to such a state of perfection, and of employing such an exact system of underground surveying, that inaccurate work must usually be attributed either to lack of care, or lack of ability in the operator.

By R. H. Oitto

To determine whether reflectors could substitute for the trip lights referred to in the Federal Mine Safety Code, the Bureau of Mines studied trip safety devices under simulated haulageway conditions. The noticeability of reflectors compared with trip lights and fluorescent panels was evaluated from distances of up to 850 feet with light source intensities of up to 1-6 foot-candles (ft c). Reflectors tested consisted of a reflective lens in a holder secured to a frame that can be attached to a trip. Reflectors were found to be suitable for use as a trip safety device. In fact, for the conditions in many underground haulageways some reflectors would be more effective than a permissible trip light.

Jan 1, 1968

By Harry Perry

One of the most notable achievements of the iron and steel industry in the United States in this century has been the general increase in productivity of individual blast furnaces and the reduction in coke rate. Most of the improvement in furnace operations has occurred within the past decade. During this time the output of the average furnace increased about one-third, while fuel rates decreased from 15 to 20 percent. For example, in 1949, the iron and steel industry produced 811.2 short tons of pig iron per blast-furnace day with a coke rate of 1,870.4 pounds per ton of pig iron, By 1960, the average production of pig iron per blast-furnace day had risen to 1,182.4 tons, while the coke rate had decreased to 1,497 pounds per ton of pig iron. These figures are averages for the entire industry; many furnaces produced over 2,000 tons per day and one furnace, operating on pellets, reached 2,700 tons of pig iron per day, Coke rates of individual furnaces varied, but some furnaces operated on less than 1,200 pounds per ton of pig iron. The significance of this decrease in coke rate is shown clearly when data on pig-iron production and coke consumption in 1959 are compared with 1948. In 1948, 57.3 million short tons of coke was charged into blast furnaces to produce 60.1 million tons of pig iron; in 1959 only 47.6 million tons of coke was needed to produce 60.2 million tons of pig iron. Thus, in 1959, nearly 10 million tons less coke was required to produce about the same amount of pig iron as was produced in 1948.

Jan 1, 1962

By Sangseom Jeong, Kyoungyul Kim, Jaeyeon Cho

"Abstract The lateral earth pressure of vertical circular shaft is investigated by using experimental tests and a theoretical analysis. The emphasis was quantifying on the magnitude and distribution of a lateral earth pressure measured by three-dimensional arching effect. A framework for determining the earth pressure distribution on the basis of both centrifuge model and full-scale field test results is introduced. Through these studies, it is found that the lateral earth pressure decreases within active displacement (dh/H: 0.2×10-2, dh: horizontal displacement, H: Height of vertical shaft) of wall at deep excavation and the arching effect is more significant for deep excavation than for shallow excavation. It is also found that the lateral earth pressure acting on a vertical circular shaft considering arching effect is 70% smaller than that calculated by Rankine theory, and thus represents a significant improvement in the prediction of realistic earth pressure for vertical circular shaft subjected to arching pressure.INTRODUCTIONIn South Korea, an increasing need for underground excavation and the application of the vertical circular wall (i.e. vertical shaft) is becoming an important issue in engineering practice. Here the vertical circular wall is generally embedded in soft or hard rocks through weathered soil varying thicknesses ranging up to 15 m. Since 1980, a number of huge excavation projects such as underground space for constructing power stations, subways, high-speed railways, and many lifeline constructions have been performed in urban areas (Jeong and Seo, 2004). Although there have been considerable advancements in construction techniques involving vertical circular wall, it is still very important for tunnel engineers to control the lateral earth pressure. Additionally, Proper estimation of earth pressures is a key factor in design of vertical circular wall. Because of three dimensional arching effects, i.e. convex arching and/or inverted arching, the earth pressure acting on a circular type of wall is less than other types. Thus, the vertical circular wall is generally used."

Jan 1, 2014

By K. Lombard

"‘Roof support awaiting time’ (RSAT) is a term used at Goedehoop Colliery’s Simunye Shaft to describe the potential production time lost due to the continuous miner (CM) standing idle waiting for roof support to catch up. Investigations revealed that in 2013, Simunye Shaft had approximately1400 hours of RSAT, which suggests that the mine could have potentially produced an additional 280 000 t of coal. This project consisted of two parts. Firstly, the causes of the high RSAT and means to improve the situation were investigated. Secondly, as insisted by mine management, the CM cutting sequence was investigated as a possible cause of high RSAT. Machine-related challenges due to the roofbolter installing support too slowly, geological conditions (mostly hard roof conditions and slips),logistical challenges pertaining to the CM cutting sequence, man-related challenges related to operator fatigue, re-support, operator inexperience, and the absence of support targets were identified as main contributors to RSAT. Furthermore, results showed that the roofbolters in the sections at Simunye Shaft are slower than the CMs. A target of 28% reduction in RSAT was set. Experts from Kennametal and Fletcher were consulted to find solutions for the identified causes. In total, eight solutions for RSAT were identified, but the solution that contributed most significantly to reducing RSAT was to use hard roof drill bits as a standard product at Simunye Shaft. Calculations showed that by using hard roof drill bits, RSAT can be reduced by 43%, which is more than the specified 28% target. The cutting sequences at Kriel, Greenside, and Simunye Shaft, togetherwith three newly developed cutting sequences, were simulated using the UCMS (Underground Coal Mining Simulation) program. A re-aligningprinciple was incorporated into the newly developed cutting sequences toalign the cutting sequences to general support work and to reduce RSAT. A decision matrix revealed that a cutting sequence in which boxing takesplace in R3 (third road to the right of the belt road) and in which the re-aligning principle has been incorporated will be the best option for Simunye Shaft. The recommended cutting sequence will lead to a 5% increase in production.The work presented in this paper was carried out as partial fullfilment for the degree BEng (Mining Engineering)"

Jan 1, 2015

In presenting this address I am conscious of the honour that has been paid me in my election to this important office, and I am very aware that I follow, in the position of President, many distinguished men who have led the Institute over the 70 years since its inauguration in Broken Hill in 1893.It is perhaps appropriate tonight that I intend to talk about a metal which recalls the birth-place of the Institute, and is also one with which I have had a direct association throughout the whole of my working career. This metal is Silver.Silver is associated traditionally in everyone's mind with money and silverware, and has always been prized for its natural beauty and elegance. It is today one of the few metals in which world consumption has outstripped production, and the events which have occurred to bring about this situation make an interesting story.In telling this story, I propose firstly to indicate our development as a silver producing country, give an historical review of the metal, trace its use as currency and the factors influencing its price, and then say something of the old and new uses of silver. Finally I shall give some comments on silver production in Australia today.Australia, with 6-5 per cent of the world's output of silver, ranks sixth among the producer countries and over the years has contributed 892.5 million ounces to the world's supply which, based upon production since the discovery ofAmerica, is estimated to have been 22,150 million ounces or nearly 680,000 tons.Although our production appears relatively small by...

Jan 1, 1963

By Georgene Renner, William R. Yernberg, Steve Kral

ABB provides integrated pro-cess control, optimization and information systems, drives and power-distribution equipment as well as other services and support to the mining industry. ABB also supplies electrical equipment and control systems for the openpit mining industry. This includes products for the automation of electrical equipment in mine shovels. The company offers low- and medium-voltage drives for various mineral- industry applications. And ABB provides gearless mill drives for equipment, such as semiautogenous grinding mills that are too large for conventional drives. ABB Industrial IT provides innovative hardware and software systems that cover all the requirements of the modern mining and processing plant.

Jan 1, 2004

By D. J. Kemp

The 20th century saw changes in the mining and metallurgical industry not only technically but also in social and environmental expectations. As projects continue to become larger their visibility raises concerns among many groups. For mining companies, transparency, openness, and early engagement of all parties are fundamental to assure success. An equally important task is to anticipate the standards that will be required to meet society’s expectations in the 21st century.

Jan 1, 2005

By Trevor Howie, Mal Edwards

"Thiess Contractors Pty Ltd. designed and operate the Mt Owen Mine in the Hunter Valley of NewSouth Wales, Australia on behalf of the owners of the mine, BHP Coal Pty Ltd. The mine is a multiseam open cut coal operation. Mining by Thiess commenced in September 1996 following thecompletion of the coal preparation plant. The location of the mine is shown below on Figure Al."

Jan 1, 1997

By Kristen Dunlap

There are several thousand remote stream crossing structures in the Tongass National Forest in need of removal. In 2007 thirty-three collapsing log bridges, log culverts, and metal culverts no longer in use were removed with explosives. Species of salmon, trout, char, and sculpin are present in the project area. Blasting overpressures may injure or kill fish in streams and ground vibrations can damage salmonid embryos in streambeds. Regulatory agencies offer guidelines with limits for blasting induced overpressures and vibrations. However, there has been no quantification of blast overpressures in shallow streams. Methods used to predict lethal levels for various blasting applications have not been completely validated. This research provides guidance for analyzing ground vibrations and water overpressures during blasting activities in or around fish streams.

Jan 1, 2009

By L. V. Clark, Arthur La Motte

"INTRODUCTION The U. S. Bureau of Mines in 1930 and 1931 made a study of the properties and characteristics of liquid-oxygen explosives (L.O.X.) at the request of one of the largest users, in order to determine and eliminate the hazards attending its use.This report deals with the examination of absorbents for L.O.X. to (1) determine their most desirable and most undesirable characteristics, (2) to find ways and means of desensitizing absorbents to mechanical shock, and (3) to determine the effect that such desensitization of absorbents has on the explosive Characteristics of L.O.X.ABSORBENT MATERIALS The absorbent used in driving the Simplon Tunnel, the earliest project in which L.O.X. was used, was composed of crude petroleum, soot, and kieselguhr. During the World War, powdered cork, soot, sawdust, powdered straw, or other similar powdered materials were mentioned in the German military instructions for use of ""liquid air"" explosives. At that time the common types of absorbent, materials were compounded ones containing the above ingredients as well as kieselguhr, paraffin, gas oils, charcoal, bituminous coal, etc.Kuryla and Clevenger4 investigated absorbents of the above type and made the following statement concerning them:"

Apr 1, 1932

By Alan Galley

CMIC Mandate CIM Annual Meeting, Toronto, May 6, 2013 To increase mining research, innovation and commercialization efforts in order to strengthen Canada?s pre-eminent role as a global leader in mineral exploration, mining and knowledge-based services and technologies. To increase the supply of highly qualified graduates from mining and earth sciences faculties to meet the significant demand today and into the future of industry, governments and academia. The CMIC initiative is intended to develop long term research strategies that extend five or greater years. Such a research plan will underpin fundamental research and innovation and the training of HQP

May 1, 2013

THE first session of the Institute was held at the Smithsonian Institution, on Tuesday evening, February 22d. The members were welcomed to Washington and to the Smithsonian by Prof. Joseph Henry. President Holley responded to the cordial welcome of Professor Henry, and then read an introductory address on the subject of Technical Education. Following the discussion on President Holley's address the following persons, duly proposed and indorsed by the Council, were elected members and associates of the Institute : MEMBERS. Emile R. Abadie, - St. Louis, Ma. R. J. Anderson, - Pittsburgh, Pa. Commander L. A. Beardslee, - Washington, D. C. Charles Bender, - New York City. Channing M. Bolton, - Richmond, Va. Thomas E. Bowman, - Silverton, Colorado. Calvin E. Brodhead, - Bethlehem, Pa. M. L. Brosius, - Lewistown, Pa. Harvey H. Brown, - Cleveland, Ohio. James A. Burden, - Troy, N. Y. J. P. Clemes, - Sonora, Mexico. N. H. Cone, - Nederland, Colorado. W. F. Durfee, - New York City. Robert Frazer, Jr., - Ashland, Pa. Joseph E. Galigher, - Bingham, Utah. William Golding, - Steel Works P. O., Pa. Samuel E. Griscom, - Pottsville, Pa. Gen. E. Burd Grubb, - Beverly, N. J. Arthur R. Guerard, - Charleston, S. C. Edward Hart, - Easton, Pa. Prof. Lewis M. Haupt, - Philadelphia. . R. S. Hawley, - Buffalo, N.Y. John W. Hoffman, - Philadelphia. Nelson P. Hulst, - Milwaukee, Wis. H. C. Humphrey, - Philadelphia. Ed. P. Jennings, - Ithaca, N. Y. B. F. Jones, - Pittsburgh, Pa.

Jan 1, 1876

By Lennart Mukka

The Kiruna Mine in Sweden currently has three ventilation systems. The first two (a new and old system) serve the production areas. The third system is used for the facilities on the former main haulage level 775. That area includes offices and workshops for load haul dumpers (LHD) and drill rigs. The third ventilation system also covers the crushing and haulage on level 1045. At the present time, the total airflow for the mine is 1,600 m3/sec(3.4 million cfm). The current system serves the levels above the 775 level. The new one is for the levels between 775 and 1,085 m (2,540 and 3,560 ft), which are needed for the new ore body. When all of the production is below level 775, the old ventilation system will be closed down.

Jan 1, 2002

By Murray Malott

The Sheppard Subway extension is currently being constructed in Toronto, Canada for the Toronto Transit Commission (TTC). McNally International Inc., in a joint venture with PCL and the Foundation Company of Canada were awarded the Twin Tunnels contract of the Sheppard extension. The Twin Tunnels project is approximately 4.4 km in length and consists of two separate twin bore drives each 3.3 km and 650 m in length and approximately 400 m of cut and cover construction. This paper presents a case history of the construction of the soft ground tunnels through the complex Toronto glacial deposits using two 5.9 m outside diameter Lovat earth pressure balance (EPB) tunnel boring machines.

Jan 1, 1999

By Victor C. Bryan

One of the most sought after answers in any consideration of blasting activities relative to mines and quarries is how to safely and efficiently use explosives. While that discussion might be relatively straightfonvard in a “site specific” situation. it becomes more complex when viewed from a broad geographic perspective. Such is the case in considering the operations of one United States producer of crushed stone with surface and underground mines spread over a thirteen state area. Differing geologic environments set conditions that dictate to the blaster as now specifically to get optimum results from the blast hole. This treatise is a discussion of the various methods, materials, and principles used in conducting such blasting operations.

Jan 1, 1991

By R. B. Schluter

Magnetite pellets were simultaneously reduced and indurated on a laboratory scale in order to determine the effects of temperature, induration time, degree of metallization, and sulfur content upon the physical and chemical properties of prereduced pellets. The reductants were commercially-pure tank gases. Among the findings were these: 1,100° C is the minimum temperature that will produce acceptably hard pellets using carbon monoxide as the reduc-ing gas. Prolonged treatment time improves the pellets' crushing strength, but the rate of improvement falls off sharply after 2 hours' induration. At 1,120° C, 75-percent metallization produces the maximum crushing strength; there was no corresponding peak at 900° or 1,050° C. Sulfur in the furnace atmosphere lowers the required induration temperature. A few tenths of 1 percent sulfur in the pellet increases the sintering rate of metallic iron in pellets by forming a liquid FeS phase that facilitates iron transfer.

Jan 1, 1968

By S. R. Borrowman

This investigation by the Bureau of Mines was undertaken to develop information on the extractive metallurgy of thorite ores because potential ore bodies of this mineral have been found recently in Colorado, Idaho, and Montana. Basic information on thorite ore treatment that would be useful in appraising the potential of these and other domestic thorium resources was developed. The work was done mainly on thorite ore containing 3.87 percent ThO2 from the Powderhorn district, Colo., and on a composite sample containing 0.52 percent ThO2 from the Wet Mountains district, Colo. Limited tests of d corroborative nature subsequently were made on a sample containing 2.30 percent ThO2 from the Lemhi Pass area on the Idaho-Montana border.

Jan 1, 1962

A commonplace, sometimes overlooked or taken for granted, article of everyday existence is the tin can. Produced from thin gauge low carbon steel, and commonly coated with a mere 60 millionths of an inch of pure tin, the product is however strong and corrosion resistant. Tin-plate serves a myriad of purposes-the most important being to meet the requirements of the canning industry. Australia's newest steel product, tin-plate, was first produced on a commercial scale during the early part of August, 1957. The commissioning of the Hot Dip Tinning Plant (Fig. 1) of The Broken Hill Proprietary Co. Ltd. at Port Kembla, marked the culmination of a proposal dating back to 1939, the advent of World War II having caused its deferment to the present time.Cornish tin is known to have been exported as early as 300 B.C. to Syria and tinned vessels existed even in the year A.D. 23. The tin coating of plate could be described as an ancient art, believed to have had its origin in Bohemia in the thirteenth century. During the next 450 years, the process spread through Saxony to Pontypool in Monmouthshire, but it was a further half century before any measure of success was obtained.Perhaps the two greatest milestones in tin-plate manufacture were the rolling of iron plates first carried out in 1728, thereby outmoding the hammer formed sheet, and more recently, the development of the electro-deposition process. By the nineteenth century, several important changes had arisen; namely, the substitution of steam for water power, coke for charcoal in the production of the base metal, and...

Jan 1, 1958

By John F. MacDonald

From 19BS thru the present, Guy F. Atkinson Construction Company has been involved in several transportation construction projects in the Seattle area. Two of these contracts, the Mt. Baker Ridge Tunnel, and The Seattle Bus Tunnel, had unique foundation features. MT. BAKER RIDGE TUNNEL ACCESS PITS The Mt. Baker Ridge Tunnel is part of the general upgrading of the I-90 freeway between I-405 and I-5 (see Fig. 1). It is located on the western shore of Lake Washington and consists of a 1300 foot long large diameter tunnel thru Mt. Baker Ridge. The ridge consists of over consolidated silts and clays overlain by a loose to medium dense silty fine sand. The water table is perched in this upper layer of material. The clays of Seattle have a history of being very sensitive to excavation. The hills are marginally stable and numerous landslides have occurred recently in the area of the tunnel. [ ]

Jan 1, 1990