Search Documents

By E. C. Reed

Oil was discovered in Nebraska on Nov. I, 1939, when the Pawnee Royalty Company's Boice No. I well, about 3 miles west of Falls City (NE 1/4 NE 1/4, sec. 18, T.r N., R.16 E., Richardson County) was drilled into the Hunton formation but the develop-ment of the area took place during 1940. After a pumping test lasting 18 days, the Boice well stopped producing and failed to qualify for the State bonus of $ 15,000 offered for the first oil well to produce go bbl. per day for 60 consecutive days. On May 9, 1940, the Pawnee Royalty Company's Bucholz No. I well was completed about M mile southeast of the discovery well and flowed at the rate of about 330 bbl. per day, easily meeting the State bonus requirements. In addition to the discovery well, which later was reconditioned, and the bonus well, 28 producers were drilled in the Falls City field during 1940. Of these wells, 23 are in sec. 20, two are in the northern part 'of sec. 29, two in the southwestern part of sec. 17 and three in the eastern part of sec.

Jan 1, 1941

By B. R. Reddy, Y. V. Swamy, B. V. R. Murthy, H. S. Ray

The Ni oxide was reduced with a CO-CO2-N2 gas mixture and the effects were observed of process variables such as roasting temperature, time and CO partial pressure. Extraction of over 90% of Ni was achieved by ammoniacal leaching of ore that had been reduced for 1 h at 760 degrees C under a gas mixture with a volumetric CO/(CO+CO2) ratio of 0.57. The kinetic data were found to conform to the Ginstling-Brounstein equation. The applicability of this model was confirmed by evaluating the apparent activation energy with the use of independently constructed differential and integral plots, which showed an excellent match

Dec 1, 1995

By George S. Rice

[This paper gives the details of tests to determine the design of stoppings capable of withstanding a pressure, applied to either side, of 50 pounds per square inch,6 as required by section 104 (a) of the Operating Regulations to Govern Coal-Mining Methods on Leased Lands on the Public Domain, issued in 1921 and quoted oil page 3. The regulations stipulated that the design for such stoppings must lie approved by the United States Bureau of Standards. The engineers of that organization felt that knowledge of the strength of such structures with respect to the effect of explosion pressure in comparison with static pressure and the strength of the walls which furnish the abutments was insufficient to justify drafting specifications; therefore, tests were needed to give information upon which a rational system of design could be based. A study was then begun; and several series of tests, made by the United States Bureau of Mines and the United States Bureau of Standards in cooperation, grave information upon which are based the detailed specifications offered in a later section. Slabs representing concrete stoppings, with and without reinforcement, were tested at the Bureau of Standards in Washington D. C.; afterwards, full-scale stoppings were tested at the Bureau of Mines Experimental mine near Pittsburgh. It was assumed that in most coal mines the strength of the floor and roof could not be relied on, but dependence must be placed upon the strength of the coal ribs. The tests developed that the maximum strength of an unreinforced concrete stopping was obtained when it acted as a flat arch buttressed against the coil ribs; but its ultimate strength depended upon the resistance to movement offered by the coal strata against which its ends were restrained or buttressed.]

Jan 1, 1931

By A. Mahmoudkhani

There has been a continuous interest in chemical aids for processing Canadian oil sands by hot water extraction process since the first commercial industry operation in 1967. Several inorganic and organic chemical systems have been introduced, of which sodium hydroxide is the most widely used extraction process aid by major producers. Use of NaOH, however, results in accumulation of sodium ions in recycled water, causing higher clays dispersion and producing tailings with poor geotechnical properties that turn into mature fine tailings. This is especially true for low grade and oxidized ores, which present the greatest challenges in bitumen recovery and produce the major portion of fine tailings. In this paper, we are presenting a novel method based on use of inorganic polymers as process aids for various low grade oil sands ores. Denver flotation cell and a laboratory scale hydrotransport loop were utilized to evaluate the effect of chemical dosage and operating parameters on the processability of oil sands samples from Athabasca region. Process tailings were examined for properties such as water chemistry, suspended solids, settling rate and the ease of tailing treatments. Our results demonstrate that the use of inorganic polymers during the froth process lead to a significant improvement in bitumen recovery from low grade oil sands and can improve further tailing treatments. This offers a viable solution that can be easily incorporated into current processing facilities and deliver several operational and economical benefits. Advantages in use of inorganic polymers versus sodium hydroxide are presented in details.

Jan 1, 2012

By B. Stimpson, K. Kosar, K. Barron

"A number of high wall failures have occurred in some of the Alberta coal strip mines of a type called by the authors ""Multiple block plane shear slope failure "". They cause rapid deterioration of the dragline bench, reduced productivity and maintenance costs.The failures are invariably associated with the presence of almost horizontal (± 5 degrees) bentonitic clay bands in the overburden, often immediately above the coal seam, and regress behind the slope as a series of tension cracks which isolate detached blocks. As many as 17 sets of cracks have been observed, at lateral distances in excess of five times the slope height from the toe.The theory of this mode of failure is presented and a limiting equilibrium computer program which will produce deterministic or probabilistic (Monte Carlo) solutions is briefly described. A case history of one such failure is documented. It is shown that the extent of the regressive failure is exceedingly sensitive to the water table elevation, leading to the conclusion that drainage, if practical, represents the best control strategy. IntroductionA number of high wall slope failures are occurring in some of the coal strip mines in Alberta of a type called by the authors ""Multiple block plane shear slope failure""(I). These failures cause a rapid deterioration of the bench from which the dragline operates, reduced productivity, and necessitate conregresses into the slope as a series of tension cracks and detached blocks. As many as 17 prominent cracks or crack zones have been observed, the last being in excess of five times the slope height distant from the toe.The block between each pair of cracks must be at limiting equilibrium, i.e. the factor of safety equals one. This condition can be used to determine the locations of the cracks which develop in sequence behind the face."

Jan 1, 1986

By W. K. Connor, O&apos

The U.S. Bureau of Mines investigated the Sheep Creek prospect in the north-central Alaska Range to evaluate the Pb, Zn, Ag, and Sn resources. The studies included field investigations, mineralogical characterization, and concentration tests. Mineralization at Sheep Creek consists of disseminated, banded, and massive pyrite, sphalerite, and galena. Tin occurs as grains of cassiterite (Sn02) in the quartz-mica matrix and within pyrite and sphalerite grains, and Ag occurs in solid solution within the galena. Three bulk surface samples and two sets of core samples were collected at the Sheep Creek prospect for this study. Gravity concentration yielded products with up to 30 pct Sn, and the best result was a product that recovered 52 pct of the Sn at a grade of 22 pct Sn. Bulk sulfide flotation yielded products that recovered up to 89 pct of the Zn, 73 pct of the Pb, and 75 pct of the Ag, but grades were relatively low; selective flotation would significantly increase the grades.

Jan 1, 1989

By G J. Lyman

In sampling a process stream, conventional sampling theory deals only with the variation of the analyte content and neglects the impact of the variation in the mass flow on the sampling variance, whether the sampling regime is time-based or mass-based. This is an obvious simplification of the real state of affairs and it is worthwhile to study this impact via simulation.With a facility to simulate large (long) random functions having some thousands of points in the function and the ability to impose covariance functions on the mass flow and analyte variations, such a study is possible. It is also possible to evaluate the impact of correlation between analyte content and mass flows.This paper describes a limited study of the variance increase due to mass flow fluctuations over the usual sampling variance due to analyte variation during the sampling period. The bias in the sampling result is determined for specific modes of correlation. Simulation methods are used as they are the only means by which a sampling result can be compared to the true assay for the lot; in the physical circumstances of mineral process analysis, it is never possible to determine the true process stream assay.CITATION:Lyman, G J, 2017. The impact of the weighting error, in Proceedings Eighth World Conference on Sampling and Blending , pp 311–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By J. Daavittila

In the latter part of the 1980s Outokumpu Chrome in Tornio, Finland, was in a situation when its twenty-year-old ferrochrome plant was becoming too inefficient to sustain economically sound production. The company made extensive studies on the then available processing methods to find out the best possible processing route. As a result, the whole plant was practically rebuilt and expanded. When equipment was proven in practical operation, an application for FeMn production was developed. Now as the Tornio FeCr-plant is considering expansion, the same type of exercise is to be performed with today?s challenges, which will be discussed in the paper. These challenges include increasing costs or decreasing quality of raw materials, increasing energy costs, stricter environmental regulations and demand for better working conditions. The possibilities of resolving to these challenges will be discussed in the paper. The future and continuing development with FeCr includes the better utilization of process dusts and a lower consumption of energy. By adapting the latest automation tools to better control the process, even higher efficiencies can be achieved with present technology. New processes are considered for development in the future and some possible technologies will be described.

Jan 1, 2004

The 21st Annual American Mining Hall of Fame Awards Banquet sponsored by the Mining Foundation of the Southwest will be held at the Sheraton Tucson Hotel in Tucson, AZ on Saturday, Dec. 6, 2003. This year’s inductee, guest of honor and featured speaker at the banquet will be Thomas J. O’Neil, recently retired president and chief operating officer of Cleveland Cliffs Mining. Prior to Cliffs, O’Neil spent 10 years with Cyprus Minerals. He was also professor and head of the Department of Mining and Geological Engineering at the University of Arizona. As representatives of mining heritage, the Hall of Fame will induct James Boyd and Thomas F. Walsh. Walsh discovered a rich gold telluride vein in Ouray, CO, which became the Camp Bird gold mine. Boyd was a former director of the U.S. Bureau of Mines, vice president of Kennecott Copper and later president of Copper Range.

Jan 1, 2003

By B. P. Watson

Several large falls of ground occur annually in the narrow, tabular stopes mined in the Bushveld Complex. These falls comprise safety risks and cause substantial production losses and compromise efforts to increase productivity. Underground observations in conjunction with instrumentation sites were used to establish the strategic parameters required to describe the rock mass behaviour of shallow-dipping stopes on the Bushveld platinum mines. Existing rock mass rating systems were evaluated using the observations and instrumentation results. None of the current systems adequately described all the relevant geotechnical conditions. Thus a hybrid of several current systems was developed, and the proposed system is discussed in the paper. The new rock mass rating system is termed the ?New Modified Stability Graph? system and follows the method originally described by Mathews et al.1and revised by Hutchinson and Diederichs2.Changes have been made to some of the tables provided by Barton3and to the stress analysis suggested by Hutchinson and Diederichs2. In addition, the logistical regression analysis has been applied to databases, formed using the suggested analyses, for three support resistances and risk levels established.

Jan 1, 2004

By J. G. Kirby

The total number of petroleum refineries in the United States continued to decline during 1950, and according to the Bureau of Mines annual refinery capacity survey there were 357 refineries January 1, 1951, compared with 367 a year ago. The total throughput capacity increased 267,344 barrels daily during the year to 6,963,644 barrels daily as of January 1, 1951, continuing the trend of the past several years to increase the throughput capacity of the refineries and decrease the number of plants. The capacity of the average refinery to process crude oil increased during 1950 from 18,246 barrels daily to 19,506. The Indiana-Illinois refinery district accounted for 110,175 barrels, or 41 percent of the total crude-oil capacity increase, the Oklahoma-Kansas district, 17 percent, the California district, 14 percent, the East Coast district, 13 percent, and the Louisiana Gulf Coast district, 12 percent. Slight declines ill crude-oil capacity were reported in the Texas Inland, Texas Gulf Coast, New Mexico, And Appalachian refinery districts. The 160,100 barrels of additional crude-oil capacity that was building January 1, 1951, represents an increase of 10 percent over the year earlier figure. The only completely new refinery listed as under construct ion at the beginning of 1951 is located at Superior, Wisconsin. Other new construction involves enlargement of existing refineries. Plans for at least five additional new refineries are under consideration, and construction is expected to begin during the current year.

Jan 1, 1951

By F. Calizaya, S. Bhattacharyya

"This study presents the results of a set of sound level measurements carried out in three underground mines where auxiliary fans are used regularly. Sound levels as high as 100 dB(A) by the workings and 115 dB(A) by the fans were measured in these mines. These levels are quite high even for intermittent noise. Ventilation layouts and best practices used to overcome potential problems related to overexposure to fan noise in underground hard-rock mines are presented here. Factors such as fan type, rotational speed, and silencer-duct arrangements and their effects on noise attenuation are discussed. INTRODUCTION Auxiliary fans are used in hard-rock mines extensively. They are used to ventilate development headings, crusher rooms, conveyor transfer points, and underground shops. They are also used in developing long tunnels and ramps. Depending on the flow requirements and space restrictions, single or double stage axial fans with rigid or flexible ducts are used. Usually, they are high pressure (3.75 kPa) fans with flow rates ranging from 7.1 m3/s to 30 m3/s. The input power varies from 15 kW to 113 kW (Mutama, 2004; O’Connor, 2008). Typically, a 113 kW fan can produce sound levels as high a 113 dB(A) (Howes, 2005). Silencers are often omitted for cost reduction purposes or when used, they are not well maintained. Furthermore, silencers provide limited attenuation depending on their length and type. Typically, the sound attenuation ranges from 10 dB(A) for a 1 × D silencer to 14 dB(A) for a 2 × D silencer, where D is the fan diameter. In a mine, the silencer is subject to wear and tear, especially when the silencer is used in harsh environments. The interior lining can get clogged and the acoustic fill can get covered by dust and diesel soot, thus reducing the silencer performance. Periodic cleaning of the interior casing can increase the attenuation capacity of a silencer by 6 to 9 dB(A) (Dabson & Acuña, 2017). However, this requires a special silencer design in which the inner cartridge can be removed, the sound absorbing material replaced, the inner casing cleaned and the whole set retrofitted. A number of techniques can be used to reduce auxiliary fan noise in underground mines. These range from selecting the right fan for the job to installing adequate silencers. The choice depends on the air quantity requirement at the working place, cross-sectional area of the opening, duct diameter, fan type (axial or centrifugal) and local restrictions. Auxiliary ventilation layouts and best practices used to overcome potential problems related to overexposure to fan noise in underground hard rock mines are presented here. Factors such as fan type, rotational speed, duct diameter, and silencer-duct arrangements and their effects on noise attenuation are discussed."

Jan 1, 2019

By Maria Agostina Cinellu

Some aspects of the reactivity of the two different kinds of gold(III) oxo complexes [Au2(N,N)2(?-O)2][X]2 [N,N = 2,2'-bipyridine (bipy) (1), 6-alkyl-2,2'-bipyridine (bipyR) (2), R = Me a, CH2Me b, CHMe2 c, CMe3 d, CH2CMe3 e] and [Au2(C,N,N)2(?-O)][X]2 [HC,N,N = 6-benzyl-2,2'-bipyridine (bipyR') (3), R' = CHMeC6H5 a, CMe2C6H5 b] (X = BF4, PF6) have been studied. Treatment with water converts the unsubstituted bipyridine complex [Au2(bipy)2(?-O)2][PF6]2 (1) and the cyclometallated derivatives [Au2(C,N,N)2(?-O)][PF6]2 (3) into the water soluble monomeric hydroxo species [Au(bipy)(OH)2][PF6] (4) and [Au(C,N,N)(OH)][PF6] (5), respectively. These hydroxo species, likely the intermediates in the formation of the oxo complexes, are quantitatively reverted to the latter ones by reflux in anhydrous solvents. Both kinds of oxo complexes react with PPh3 to give OPPh3, the gold(I) complex [Au(PPh3)2][PF6] and the free bipyridine ligands. The reaction of the dioxo complexes [Au2(bipyR)2(?-O)2][PF6]2 (2a, 2b, 2c, 2e) with different alkenes gives the unprecedented alkene complexes [Au(bipyR)(?2-alkene)][PF6]. The styrene adduct [Au(bipyip)(?2- CH2=CHPh)][PF6] (7) (bipyip = 6-iso-propyl-2,2?-bipyridine c) has been characterized, inter alia, by X-ray diffraction analysis. Organic products arising from olefin oxidation are also found in the reaction mixture.

Oct 1, 2003

Trans No. Place Date Vol. 1. Wilkes-Barre, Pa. May, '71 1 2. Bethlehem, Pa. Aug., '71 1 3. Troy, N. Nov., '71 1 4. Philadelphia, Pa. Feb., '72.. 1 5. New York, N. Y. May, '72 1 6. Pittsburgh, Pa. Oct., '72 1 7. Boston, Mass. Feb., '73 1 8. Philadelphia, Pa. May, '73 2 9. Easton, Pa. Oct., '73 2 10. New York N. Y. Feb., '74 2 11. St. Louis, Mo. May, '74 3 12. Hazleton, Pa. Oct., '74.. 3 13. New Haven, Conn. Feb., '75 3 14. Dover, N. J. May, '75 4 15. Cleveland, Ohio Oct., '75 4 16. Washington, D. C. Feb., '76 4 17. Philadelphia, Pa. June, '76 5 18. Philadelphia, Pa. Oct., '76 5

Jan 1, 1932

By A. Barba, M. P. Gómez, F. Puertas, M. Palacios, M. F. Gazulla, S. Martínez-Ramírez, I. García-Díaz

"The present study explores the reactivity and burnability of cement raw mixes containing fired red or white ceramic tile wastes or combinations of the two as alternative raw materials. The results showed that the new raw mixes containing these wastes are technically viable. The reactivity and burnability of the new raw mixes have been evaluated; confirming very good results when the particle size of wastes was less than 90 µm. The chemical and mineralogical compositions of the new clinkers were comparable to clinker manufactured with conventional raw materials. The mix of red and white ceramic tile waste was found to perform as well or better than each type of waste separately, a promising indication that separation of the two would be unnecessary for these purposes.IntroductionPortland cement clinker production consumes large amounts of energy (850 kcal/kg clinker) and has a considerable environmental impact. This involves massive quarrying for raw materials (limestone, clay etc), as it takes 1.7 tonnes to produce one tonne of clinker, as well as the emission of greenhouse and other gases (NOx, SO2, CO2) into the atmosphere. Around 850 kg of CO2 are emitted per tonne of clinker produced.The cement industry is looking for solutions to these problems, to attain sustainability and comply with the Kyoto Protocol commitments [1,2]. For that reason, experimental ways are being explored to develop cements whose manufacture is less energy-intensive, less damaging to the surrounding environment and with lower tendency to emit polluting gas. One of the reach this objective is the use of industrial waste and by-products as alternative materials for cement manufacture. Such alternative materials may partially replace fuel [3,4], conventional raw materials [5-8] or clinker in the final composition of the cement [9]."

Jan 1, 2008

Trans No. Place Date Vol. 1. Wilkes-Barre, Pa. May, '71 1 2. Bethlehem, Pa. Aug., '71 1 3. Troy, N. Nov., '71 1 4. Philadelphia, Pa. Feb., '72.. 1 5. New York, N. Y. May, '72 1 6. Pittsburgh, Pa. Oct., '72 1 7. Boston, Mass. Feb., '73 1 8. Philadelphia, Pa. May, '73 2 9. Easton, Pa. Oct., '73 2 10. New York N. Y. Feb., '74 2 11. St. Louis, Mo. May, '74 3 12. Hazleton, Pa. Oct., '74.. 3 13. New Haven, Conn. Feb., '75 3 14. Dover, N. J. May, '75 4 15. Cleveland, Ohio Oct., '75 4 16. Washington, D. C. Feb., '76 4 17. Philadelphia, Pa. June, '76 5 18. Philadelphia, Pa. Oct., '76 5

Jan 1, 1942

By H. P. Greenwald

Cooperation between the Bureau of Mines of the United States Department of the Interior and the Safety in Mines Research Board of Great Britain dates from 1924. It has been intimate and has involved exchange of personnel and. equipment as well as information. Correlation of divergent results obtained in large-scale tests of the explosibility3/ of coal dusts made in the respective countries was one of the first problems to be studied. The purpose of this paper is to show to what extent such correlation has been achieved. COMPARISON OF TEST METHODS The first research accomplished Jointly by the two organizations was a comparison of large-scale methods of determining the explosibility of coal dust. Large samples of coal were exchanged and subjected to test in the Bureau's Experimental coal mine and in the Board's steel gallery, 38 inches

Jan 1, 1939

By W J. Rankin

A study was carried out to compare the environmental impacts of a number of process routes for lead and zinc metal production from sulphide ores using Life Cycle Assessment methodology and based on average industry data derived from the literature. The processes investigated were:blast furnace production of lead; Imperial Smelting Process for lead and zinc production; and electrowinning of zinc with the mining and mineral processing stages common to all three routes. The effect of a number of process variables, namely ore grade, fuel source for electricity generation and efficiency of generation, on the environmental impacts was also examined. The environmental impact categories considered in the study were:total (or full cycle) energy consumption; Global Warming Potential (GWP); and Acidification Potential (AP). The results of the study show that when produced separately, zinc production is more than twice as energy intensive as lead production (viz 48 and 20 MJ/kg respectively), however when produced jointly by the Imperial Smelting process, the energy intensity of the two metals is not all that dissimilar (viz 36 and 32 MJ/kg respectively). The metal production and refining stage was found to make the greatest contribution to the overall environmental impacts for all three processes. The study also highlighted the importance of taking a life cycle approach when comparing the environmental impacts of different processes.

Jan 1, 2002

This paper discusses support requirements for the proposed monorail system to be used in decline development. The monorail drilling and loading systems are systems that move on the rail (monorail) installed in the roof of the decline and supported by roof bolts, suspension chains and steel supports. However, due to the weight of the components of the two systems, it is imperative that the force in each roof bolt, suspension chain and steel support capable of suspending the weight of the heaviest component is determined. Numerical models that relate the weight of the monorail drilling and loading components to the required strength in the support system have been developed. Using these developed models, numerical values of the forces in each roof bolt, suspension chain and steel support, required to suspend the weight of the heaviest component of the monorail drilling and loading systems are determined.

Dec 6, 2010

By J. Drelich, C. L. White, Ch. Zhou, W. M. Cross, E. T. Zellers, E. M. Nadorny

A laser-based particle deposition (LBPD) technique has recently been developed at Michigan Technological University for patterning mesostructures made of nanoparticles and their clusters. The LBPD technique makes use of laser induced optical forces to transport and pattern nanoparticles on a variety of conductive and non-conductive substrates from nanoparticle-in-liquid suspension. A weakly focused laser beam is used to confine and propel particles along the laser beam. Confinement is accomplished by forces due to optical field gradients that act on polarizable particles and tend to move them to axis of the laser beam. The force propelling the particles along the direction of the laser beam arise from momentum conservation of photons scattered from the particles. In this paper, this novel LBPD technology is briefly reviewed, and several examples of patterning are presented. The size and morphology of mesostrips produced from gold and polystyrene nanoparticles, under a range of deposition conditions, have been characterized by optical microscopy, atomic force microscopy, and scanning electron microscopy. The results presented here demonstrate that gold and polystyrene nanoparticles deposited by LBPD can form clusters of particles. When deposited at an appropriate rate, such clusters can form multilayer mesostrips of high particle density. One goal of research on such systems is to fabricate arrays of parallel lines made up of colloidal particles having a range of surface functionalities. Such arrays have potential for application as novel microsensors for environmental sensors.

Jan 1, 2003