Search Documents

By D Craw, J Becker

Post-metamorphic structural evolution of Otago Schist resulted in a pattern of northwest and northeast striking faults and fractures cutting the basement rocks. These faults have been reactivated several times since Mesozoic metamorphism. Gold-bearing quartz veins which have been exploited sporadically over the past 130 years are almost invariably hosted by northwest striking structures, and most exploration has been focussed on these structures. There is evidence for hydrothermal activity and mineralisation along some of the northeast striking structures, although there has been very little work done on these structures. Our study is attempting to characterise the hydrothermal processes in the northeast structures, in comparison to the northwest structures, in order to see if further detailed exploration is warranted. There is evidence for both normal and reverse senses of movement on northeast striking faults, and some of the faults have evidence for early ductile deformation overprinted by later brittle structures. Northeast striking structures host stibnite mineralisation in places, and faults are locally silicified or extensively impregnated with ankeritic carbonate. Sulphides are rare in veins, but do occur in some hydrothermally altered host rocks. Hydrothermal haematite accompanies extensive silicification along the Manuherikia fault zone near Alexandra. Anomalous gold concentrations occur in some hydrothennal zones, and in downslope sediments in some localities.

Jan 1, 1998

By Dai Xi

In the present work, the viscosities of molten FenO-MgO-Si02 and FenO-MgO-CaO-Si02 semi-synthetic slags for nickel flash smelting were measured in the temperature range from 1473 to 1723K by a rotational viscometer. The ratio of Fe to Si02 was fixed at 1.2, calcium and magnesium oxide contents varied in the range from 2 to 8 mass% and 9 to 12 mass%, respectively. The results showed that silicate anions became smaller by increasing CaO content, which results in a decrease of the viscosity of the slag. In the case of MgO addition the viscosity behavior was complicated. At MgO content below 11 mass%, the viscosity increased with the increase of MgO at all temperatures tested. However, when the MgO content was above II mass%, the viscosity decreased slightly for FenO-MgO-CaO-Si02 system. At higher MgO contents, low-viscosity slags can be obtained by adding CaO. At a given composition, the viscosity decreased with increasing temperature. The higher the temperature, the more MgO can be added before saturation. The effect of Fe304 on the viscosity was quite significant. The viscosity of slag increased by 300mPa's at l573K when Fe304 content varied from 3 to 9 mass%. The viscosity values are presented as the functions of temperature and composition. A comparison between FenO-MgO-Si02 and FenO-MgO-CaO-Si02 systems is given in this study.

Jan 1, 2003

By R E. Myers, G N. Phillips

Many of the worldÆs larger iron ore deposits are hosted by rock sequences of Archaean to early Proterozoic age. Most models for the genesis of these deposits are influenced, either directly or indirectly, by the nature of the atmosphere at the time of their formation, and more specifically by the presence or absence of oxygen in the early atmosphere. Since the early-1950s, the geological literature suggests that the Archaean atmosphere was æreducingÆ, and that it may not have contained significant amounts of free oxygen until ca 2 Ga. There are many different definitions of the term æreducingÆ, but the criterion adopted here is whether crustal iron was limited to Fe2+, or whether Fe3+ was also widespread, ie was there scope for redox changes in the state of iron? Significantly, major Australian banded iron formations span this period of inferred atmosphere transition, eg Mt Goldsworthy, Mt Tom Price, Middleback Ranges. Geological evidence for a reducing Archaean atmosphere is both ambiguous and controversial (see review by Phillips, Law and Myers, 2001). Many earlier ideas (eg no Archaean redbeds; all very large iron ore deposits being post-Archaean) have been disproved by dating, whereas other evidence (eg homogeneous detrital gold grains, inferred palaeosols) has not withstood geological scrutiny. The interpretation of some data sets (eg inferred detrital uraninite and pyrite in some Archaean meta-sedimentary rocks) is still controversial. In fact, some lines of evidence now suggest that oxygen was present in the atmosphere well before 2.5 Ga (eg sulfates in the Pilbara craton, carbon distribution in clastic sedimentary rocks). An oxidising Archaean atmosphere has important implications for the development of iron formations. First, the atmosphere is an obvious potential source of oxygen to stabilise ferric iron minerals. Second, reduced fluids in equilibrium with ferrous iron are commonly inferred to transport iron in solution to the depositional site. The redox state of the atmosphere thus provides critical constraints on the solution chemistry of surface waters, effective transport paths for iron and particularly on viable precipitation mechanisms. Iron formations developed from fluids in equilibrium with the atmosphere also have the potential to provide important constraints on the evolution of EarthÆs early atmosphere. If an oxygenated atmosphere is a necessary condition for the development of iron formations, then the Archaean atmosphere must have been oxidising since at least 3.5 Ga. If the redox state of the atmosphere is not a necessary condition, then the time distribution of iron formations cannot be used to provide constraints on atmospheric evolution. Given these uncertainties, models for the genesis of iron ore deposits of Archaean or early Proterozoic age should not rely on a reducing atmosphere in the absence of independent evidence and the alternative of an oxidising atmosphere should also be considered.

Jan 1, 2002

By J. Lewis, J. Harper, M. F. Ashby

A grain boundary in a metal interacts with second-phase particles, which exert a pinning force (first estimated by Zener) on the boundary opposing its motion. We have computed the shape of boundaries which interact with more or less spherical second-phase particles and have constructed a soap-film model to reproduce the shape of the boundary surface. An important result is that measurement of this shape allows the pressure, or driving force, on the boundary to be measured. We hare applied this technique to grain boundaries in two alloys and hate measured the pinning force exerted by single second-phase jwrticles on the boundaries. It is in good agreement with Zener's estimate. J\. boundary between two grains, or two bulk phases, interacts with small inclusions or particles of a second phase, whether they are gas or solid. This interaction means that the boundary, forced to migrate by a difference in free energy between the material of the two grains or phases which it separates, exerts a force on a particle which it touches, tending to drag it forward. (The movement of inclusions through metals under the influence of this force, has, in fact, been observed. 1-3) Equally, the particle can be thought of as exerting a pinning force on the boundary, tending to hold it back. Zener (in a celebrated private communication4) first realized that this interaction, and the resulting pinning force, existed. His calculation of its magnitude was crude but adequate: a spherical inclusion of radius r blanks off an area nr2 of the boundary on which it sits; since the boundary has an energy of rMM x per unit area, the blanlung-olf decreases the energy of the system by MM: this energy is returned to the system if the boundary is pulled free from the inclusion— a forward movement of the boundary by a distance r will do this—so that the maximum pinning force is Trrym.M- A similar argument can be made for inter-phase boundaries. The nature of the particle itself did not enter this, or two subsequent treatments.5,6 When it is considered, tic leifthe energyoftheb a) The boundary may enter and pass through the particle if the energy of the boundary is lower within the particle than in the matrix. Fig. l(r/). Certain coherent precipitate particles behave like this. h) More usually, the boundary will bend round the particle, enveloping and bypassing it. Fig. l(b). In doing so, it changes the structure and energy of the interface between the particle and its matrix. This means that the boundary does not touch the particle surface at right angles, as early treatments assumed,5'9 but at some angle a which depends on this change in surface energy of the particle, and can be calculated from the equilibrium of surface tensions. Most precipitate particles and inclusions behave like this. Gas bubbles or liquid drops can be regarded as belonging to either group. The progress of bypassing is conveniently measured by the angle shown in Fig. 1. When the nature of the particle is ignored, its maximum pinning force is exerted when - 45 deg. When it is considered, this critical value of is found to depend on a and thus on the nature of the particle. The maximum pinning force lies between nryMM and 2jtjMM (Appendix 1). not very different from Zener's result. In reality, a boundary between crystals has a specific energy and tension which varies with the orientation of the boundary. Furthermore, recent experiments7 indicate that such a boundary is not atom-ically smooth, but has steps on it: migration of the boundary corresponds to the sweeping of these steps across the boundary surface, like the Frank model of crystal growth from the vapor. This means that the interaction of a boundary with particles should really be considered in terms of the way in which particles hinder the movement of these steps. To suppose a grain boundary or interphase boundary to be smooth, and to ignore the variation of its energy with orientation, is to liken it to a soap film. The advantage of this soap film approximation, which we have used throughout this paper, is that interaction energies and boundary shapes can be calculated easily. We have done this by numerical computation and by using a soap film model, and have compared the results with grain boundaries in an aluminum-based and a copper-based alloy. It turns out that the shape of the boundary which bulges between particles allows the pressure an it to be calculated; that is, the local driving force an the boundary can be measured. This has allowed us to check the Zener relationship experimentally.

Jan 1, 1970

By H. G. Oltmann

The equilibrium nitrogen solubility in the CaO-SiO2system was studied by a slag-gas equilibration technique, in graphite crucibles at 1823K under a CO-N2 atmosphere. The nitrogen content of the slags was determined by the Kjeldahl method. A reliable technique was used to obtain an initial nitrogen content in the master slags, from the addition and pre-melting of silicon nitride. Reduction of silica by graphite was found to occur during the equilibration experiments, resulting in compositional changes of the slags. The results were extrapolated to equilibrium by kinetic evaluation of the data. The nitrogen solubility showed good agreement with the result of Suito and Sano, while Fruehan?s results were lower. However, the results of the present study do not support the maximum nitrogen solubility values found by Sano.

Jan 1, 1999

By Abdurrahman Cetinbas

The effect of water infusion on the flow of methane and on the production of dust was investigated at an active face in the Pittsburgh coalbed. The average total flow of methane at the face decreased by approximately 79 percent, whereas the flow from the ribs increased about 24 percent after infusion. On the day after infusion, dust concentrations appear to have been reduced; however, the presence of large quantities of rock dust obscured the results on the following days.

Jan 1, 1972

By Y. Wang, S. Sridhar, B. Coletti, G. N. Shannon, S. Vantilt

The final removal of inclusions in the ladle, tundish, and mold in a continuous casting process involves the kinetic steps of liquid film drainage, interface rupture, and absorption of the inclusion into the overlaying molten slag. During this process, oxide inclusions can undergo chemical reactions with the slag. This paper presents recent results on imaging the slag/steel interface and elucidates the evolution of Al2O3and Al2O3-CaO inclusions during their separation from the steel and on their incorporation into the slag. Experimental results, obtained through a Confocal Scanning Laser Microscope, are compared with thermodynamic predictions.

Jan 1, 2004

By D. Peatfield

The design and operation of coal preparation plants are governed by the inherent quality of the raw coal to be processed, market specifications and the saleable tonnage requirements. Topography influences the layout of the plant but does not affect the process design. The coal market comprises many sectors, each having specific requirements with respect to both size and quality. In turn, these have led to different levels of preparation and the development of specific types of coal preparation plant design. Developments in processing techniques and processing equipment have also influenced the design and now give the preparation engineer numerous permutations in process and equipment selection. This paper gives an overview of the coal industry in general and summarizes some of the developments in the design of plants and technical developments in the areas of dense medium processing, fine coal treatment and equipment design.

Jan 1, 2003

By D. M. Avant, A. J. Solomon, S. M. Pickering, W. R. Fox

Introduction Most high purity silica is produced from crystalline quartz, generally from sand. However, there is a small area of southern Illinois where a porous, friable white chert rock is found that is very different in physical form from quartz sand. This microcrystalline material, commonly referred to as tripoli, is more easily ground to micron sizes than sand. Although of similar Moh's hardness, microcrystalline tripoli is less abrasive than either ground quartz sand or many synthetic abrasives. Location The southwestern corner of Illinois is underlain by extensive deposits of very porous chert; in some places the material is quite white. Two companies, Illinois Minerals Co. and Tammsco Inc., mine and process this white material. The Illinois Minerals plant is located at Elco, and the Tammsco plant is in Tamms, IL. Both companies mine from various locations within a 10-mile truck haul of their plants. Production from this district has been continuous since at least 1915. Malvern Minerals Co. mines and processes a generally similar microcrystalline, friable novaculite near Hot Springs, AR. Geology The southern Illinois white tripoli area is on the southern flank of the Illinois Basin. The commercial silica zone is a facies of the Clear Creek chert of Lower Devonian Age. To the north, where it occurs deep in the basin, the Clear Creek is a siliceous limestone. In the mining area, thin overburden has allowed access by surface ground water, which has leached away the carbonate content and left a quite pure silica residue. Fossils characteristic of sea bottom deposition, such as brachiopods and trilobites, are occasionally encountered in mining. The structure of the mining area is poorly known, due to infrequent outcrops. Strata in most mines are inclined at dips of 5° to 20°. There appear to be occasional high angle normal and reverse faults, but these are seldom of any significance in mining. The friable white silica zone mined in the Clear Creek chert is overlain by dark brownish-red chert and siliceous shale. Exploration drilling to date has not encountered the base of the microcrystalline tripolitic zone. Chemical content Leaching by ground water solution has removed virtually all the carbonate from the original siliceous limestone. Impurities encountered are red to yellow iron oxides, aluminous clays, and occasional black manganese oxides. The silica has no detectable formula water. A typical chemical analysis and physical properties are listed in Tables 1 and 2. Mineralogy and crystallinity Southern Illinois friable tripoli appears amorphous under the polarizing microscope. No crystal structure and only occasional, vague, patchy anisotropism is evident. However, the material gives an excellent quartz X-ray diffraction pattern. Thus, so far as X-ray mineralogy is concerned, the material is clearly

Jan 12, 1986

The EMEM Awards of the Department of Minerals and Energy (DME) were formally launched on 3 March 2000 by Ms Susan Shabangu, Deputy Minister at the Department?s Mineralia Centre in Pretoria. The launch was attended by invited guests from the mining and aggregate industries ,representatives of the Patron Organisations (see below),non- government and scientific organizations, the media, other government departments involved with mining environmental management and members of staff of the DME both nationally and regionally.

Jan 1, 2000

By T. J. Batchler

Deformable materials are sometimes added to ventilation stopping constructions to prevent damage caused by convergence in coal mines. However, adding deformable materials can significantly reduce the capacity of a stopping to resist transverse loading. As part of its mining health and safety program, the National Institute for Occupational Safety and Health (NIOSH) has conducted research on the effect of various materials with different deformation properties on the transverse loading capability of a stopping wall. Based on a three-point hinge method of failure, a half-wall method of testing in the NIOSH Mine Roof Simulator was used to simulate full-scale wall behavior. This simulated the fracture initiation and eventual failure of the stoppings from transverse loading. The impact of the modulus of elasticity of various deformable materials was examined in this study. A polystyrene foam block with a low modulus of elasticity, which is commonly used as a deformable material, was shown to degrade the transverse load capacity of the stopping by as much 95%. Other materials with higher modulus of elasticity preserved more of the transverse load capacity of the stopping, but were not able to absorb as much convergence. This paper presents the results of a parametric study that quantifies the impact of various deformable materials in block stopping construction under transverse load conditions. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By M. Rezaee

Push backs used in the production planning of open pit mines play an integral role in generating annual cash flow. Although several algorithms for push back designs have been proposed, none have studied the optimum number of push backs. In this paper, different algorithms have been implemented for the push back design of a cross section of a copper deposit and the results discussed. Moreover, the optimum number of push backs has been determined using analytical and multiple attribute decision making (MADM) methods based on minimizing the risk associated with grade uncertainty, and minimizing stripping ratio, while maximizing net present value (NPV). According to the findings, the optimum number of push backs has been proposed to be between three and six, as lower quantities of push backs are more likely to achieve the calculated net present value, and have smoother stripping ratios for different pushbacks. This approach was examined in an operating mine and the optimum number of push backs determined to be four.

Jan 1, 2012

By Aziza A. Yousef, Suzan S. Ibrahim, Mahmoud A. Arafa, Mohamed A. Abdel Khalek

In view of the shortage of soft water all over the Middle East countries, seawater may be used to replace the fresh water in flotation beneficiation. The flotation process required about 7 m3 of fresh water/ ton ore. This article aimed to study the effect of seawater cations and anions on the flotation process of four important mineral commodities. The adsorption of collector, zeta-potential, zero point of charge and floatability of pure minerals were studied. The individual effects of different cations and anions that are predominant in seawater, within their more or less actual concentrations were studied on individual mineral and on groups of them. The troublesome Ca2+ and Mg2+ ions, in the anionic circuit could be controlled by soda ash addition to the pulp before the anionic collector. The addition of sodium silicate improved the floatation selectivity of mineral mixtures and natural ore. At the optimum conditions the calcareous phosphate ore yielded a concentrate recovery of 83% with a grade of 34% P2O5, with 0.61%MgO, which from an ore assaying (25.3% P2O5 and 9.4% MgO).

Jan 1, 2003

By Georgene Renner, William R. Yernberg, William Gleason

American Commercial (ACI) offers a selection of ground control solutions. Beginning with steel liner plates installed in the Gratiot Avenue sewer system in Detroit, MI 1920, ACI is one of the leading designers and manufacturers of underground steel supports in North America. ACI is also a leader in fire-proofing underground structures with its Promat Fire Protection Boards. The sandwich panels have been used in many new and retrofit tunnel and underground construction projects worldwide. Ease of installation and replacement, cost effectiveness and superior performance have made this product line the premier choice of owners and designers for structural protection, fire-life safety requirements and architectural finish needs.

Jan 1, 2007

The Modified Zincex® Process, developed by Técnicas Reunidas, is highly flexible dealing with a wide range of pregnant leach solutions. No matter if those solutions are produced from primary or secondary raw materials, and/or are based on conventional leaching, pressure leaching, heap leaching or bio leaching the result is always high-purity zinc product. The zinc solvent extraction unit within the process is a very effective barrier for impurities and a buffer for the composition of the pregnant liquor. This unit achieves an extremely pure aqueous extract that can be converted into different final products. All of them are characterized by fulfilling the highest purity standards. Also, there is the possibility to adapt the global process to a wide range of pregnant liquor compositions and various production capacities up to a zinc production limit over 150 000 t/a with a single solvent extraction plant.

Jan 1, 2002

By Andrew Allan

[This report describe the first experiment of the Anthracite Research Laboratory, Bureau of Miners, in attempting to reduce underground-mining costs and conserve anthracite as a natural r-source by introducing now minim methods. The work war, dons in cooperation with one of the large anthracite-producing companies. It applies to productive mining, characterized by comparatively low cost, per ton and high production per man, as differentiated from development mining, which is always necessary before the, productive or retreat phase can begin. The system d scribed in this report is believed to be generally applicable to beds pitching 70° to 90° and, under certain conditions, to beds pitching loss than 70°. After development hate been completed, an openings is made, extending the full width of the 9- to 10-foot coal bad and reaching from the haulageway to the vertical limits of the solid coal. Long drill holes (20 to 50 feet) charged with about one stick of permissible explosive riper foot of length are fused to break the coal. Once broken, the coal is loaded onto a shaker conveyor by gravity and thence into mine: cars. The coal is mined retreating in 15- to 20-foot sections that are broken and loaded onto the conveyor through a specially constructed chute. In the Bureau?s experimental work, the height of sections arse ranged from 35 to 60 fact, depending on the geologic extent of the coal bed.]

Jan 1, 1952

By M. Hopf, E. Rossouw

Keywords: Pyrometallurgy, furnace, copper coolers, freeze lining, monitoring, Saveway The use of water-cooled copper components as sidewall elements of submerged arc furnaces and other pyrometallurgical applications has become increasingly common. The high cooling efficiency of copper has made it possible to increase the service life of furnace refractories when compared to conventional refractory linings. However even the self-healing effect of ?freezing? worn areas of the lining does not necessarily protect the copper coolers against wear or corrosion completely. In order to avoid furnace explosions, various methods have been used to monitor the wear of coolers. Unfortunately, these have not been able to consistently identify localized wear. Thos Begbie (South African) and SAVEWAY (German) jointly developed technology to embed a line sensor into the copper cooler during the casting process. This system allows an exhaustive monitoring of the copper cooler. A SAVELINE sensor is placed inside the copper-cooling panel between the water-cooling passage and the hot face of the panel. The sensor follows the meandering shape of the cooling water channels. In the first instance, the sensor provides analogue information as the thickness of the copper reduces. Secondly, this wear signal will be confirmed by a signal of interruption if the sensor is washed away. Because of the structure of the sensor, a self-diagnosis is possible and indications can be confirmed (double proofed). Subsequent to the manufacture of some test pieces, coolers for a large submerged arc furnace were manufactured. The sensorized coolers have been installed at the intermittent surface (slag line) where the largest amount of corrosion has been encountered. The system has been operating since December 2005 in what is considered one of the largest submerged arc furnaces in South Africa.

Jan 1, 2006

By Y Zhuang, S La Brooy

The selection of the optimum process route for a new project has traditionally consisted of investigating existing options and ranking them in terms of cost, technical risk and environmental acceptability. With the current focus on sustainable development other factors now need to be considered. Life Cycle Assessment (LCA) of the process options can be used to extend the assessment in terms of their potential for earning renewable energy credits and in judging their ability to achieve greenhouse gas emission reductions. A rigorous life cycle assessment is demanding in terms of setting the baseline for comparisons and evaluating the elements that make up the emission profiles of the process options. However, a simplified LCA can provide a useful tool for comparing different process options. This approach can be combined with traditional assessment criteria to rank the options available to the project. GRD Minproc has been intimately involved in executing LCA calculations for different municipal waste treatment options. This paper applies a similar LCA methodology to investigate the greenhouse gas implications for different options for copper processing. The process options considered are:concentrator û sale of concentrate to smelter, concentrator û on-site mini smelter, and concentrator û leach SX/EW. The paper then goes on to consider the operating cost implications that could arise with the introduction of carbon taxes or carbon credits and how these might impact on the future choice of flowsheet.

Jan 1, 2002

By K L. Brown, J L. Mauk

Sulfide-rich scale occurs in steam and water lines at the Ohaaki geothennal field,Taupo Volcanic Zone, New Zealand. Precious metals show very high concentrations around areas ofpressure reduction (Au 15500 ppm, Ag 68800 ppm). Pyrrhotite dominates at the orifice plate due to low PH2s1PH2 conditions. Sulfide mineralogy in the scales is consistent with alteration mineralogy of the reservoir rocks. Separated steam then produces a mainly pyrite/magnetite mineralogy, with lesser chalcopyrite, where textures reflect high flow rates and high levels of supersaturation. This study outlines the effect that pressure and subsequent temperature decreases have on the mineralogy, chemistry and textures of sulfide scales.

Jan 1, 1998

By N. A. Gokcen, S. Fujishiro

The dissociation pressure of Cr3C2 has been measured in the range of 1908" to 2237°K by means of graphite Knudsen effusion cells. It has been found that Cr3C2 vaporizes according to the following reaction: 1/3 Cr3C2 (s or 1) = 2/3 C (graph.) + Cr (g). The equilibrizcm pressure, P, of Cr (g) is found to be log Ps=- - (21,194/T) + 6.525 over solid Cr3C2 and estimated as log P, = - (19,535/T) + 5.76 over liquid Cr3C2. CARBIDES of chromium are of great importance in alloy steels and cemented carbides. The published data on their therm odynamic properties at high temperatures, however, are meager. The heat capacity and change in entropy of Cr3C2 were determined calorimetrically by Kelley and Moore1 in the range of approximately 50" to 300°K, and by Oriani and Murphy2 from 297" to 1188°K. The standard entropy of Cr3C2at 298.15°K, obtained by Kelley.7 was later confirmed by DeSorbo.4 Equilibrium in the reaction was investigated by Boericke.5 A recent tabular summary

Jan 1, 1962