Search Documents

By Norman F. Schulz

The technical excellence of separation achieved in a mineral concentration process, or any other process where two constituents of any kind are physically separated from each other, is expressed uniquely and quantitatively by the separation efficiency (E,): E. = (R - R,), where R is the percentage of the valuable constituent and R, the percentage of the waste appearing in the concentrate. The separation efficiency meets all the usual requirements of a true efficiency and is independent of the nature of the process used. It can be visualized as the percentage of the feed material that, in effect, actually undergoes complete separation while the rest of the feed is distributed randomly and unchanged into the two separation products. The problem of quantitatively assessing the results of a mineral concentration process recurs whenever one tries to decide which of two similar test results is more desirable. Although economic factors may greatly influence the eventual choice of process, they usually have very little to do with the technical excellence of a separation and are, therefore, not a consideration at this point. Concentrate grade and recovery, used simultaneously are the most widely accepted measures of performance, and if both the grade and the recovery are greater for one case than for another, the choice is simple. However, when the results of closely competitive operations are compared, it often occurs that one set of test results shows a higher grade and a lower recovery than another and the choice is no longer obvious. Laboratory investigations of a mineral concentration process applied to a given feed material can often be designed to yield successive paired values of concentrate grade and recovery over the practical range of the course of a separation process.' These results may be plotted as some combination of the cumulative values of grade, weight recovery, or unit recovery in the concentrate. The resulting correlations for two slightly different sets of conditions can then be compared qualitatively, or even quantitatively in particular cases.2 Such comparisons are not applicable, however, to individual concentration test results. The reduction of a separation test result to a single efficiency figure, preferably as a percentage of ideality, would afford the simplest and most precise means for comparing the results of competitive tests. The effective proportion of feed material that undergoes complete separation in any real concentration process, hereafter referred to as "separation efficiency," is such a figure. It is essily calculated from the usual feed and product data and can even be evaluated, in many cases, from data in publications describing various concentration processes. Mineral Concentration Processes and Their Evaluation Mineral Concentration Processes: The overall concentration process may be subdivided into a liberation process which severs the bonds between unlike mineral species, and a separation process, which sorts the resulting liberated particles into two products—a concentrate rich in mineral A and a tailing lean in mineral A. A perfect mineral concentration process is represented by the idealized scheme shown in Fig. 1 in which liberation and separation are not differentiated. The feed mixture consists of two mineral types which are completely liberated early in the process and then sorted by type. All the mineral particles of type A which respond uniquely to the selection forces acting in the ideal separator, report to the concentrate, while all the mineral particles of type non-A report to the tail-

Jan 1, 1971

By R. Knapp, R. Firlotte

"Les Terrains Auriferes (LIA) Property, formerly the Malartic Goldfield (Goldfield) mine, ceased its remaining milling operations in the fall of 1994. During the early years of mining, the mill processed a non-sulfide ore with substantial carbonate mineralization.In 1977 after an extended shutdown period, ore from a nearby property, Bousquet, was processed at the mill. That ore contained larger quantities of sulfides, and unlike the old tailings, had acid generating potential.Upon closure of the L TA mill, the closure options considered for the L TA site were to cover with:1. a thin cover of 0.5 metres of borrow material (sand and gravel) to achieve basic erosion protection/stabilization; collect acidic seepage and treat with lime.2. a 2 metres of non-acid producing tailings; final surface to be vegetated.3. an engineered oxygen barrier consisting of a multi-layer cover; final surface to be vegetated.The paper presents the technological and economical methodologies that were used to select the closure alternative, describe the associated construction challenges that were faced with the implementation of the multi-layer cover concept and presents preliminary results on the cover's performance.In addition to being the first full scale demonstration of this type of multi-layer engineered oxygen barrier cover technology, this project had the advantage of using non acid producing mine tailings as part of the reclamation solution."

Jan 1, 1997

By Stig O. Olofsson

The problem of overbreak in underground construction and mining is normally approached by a variety of smooth blasting methods. Numerous small diameter, low velocity explosives have been developed specifically for blasting the contour line. Increased mechanization in rock excavation has led to the development of several methods of mechanical explosive loading. A new mechanically loaded smooth blasting explosive was developed in Sweden . However, several limitations were realised, which after several trials resulted in a hybrid smooth blasting method, The Suaer Cautious Contour Blasting Method which will be discussed in this paper.

Jan 1, 1994

By Jorj O. Osterberg

The Osterberg (O-Cell) Method makes it possible to separate the side shear resistance (skin friction) from end bearing. The O-Cell is placed on or near the bottom of a drilled shaft and after the concrete is poured and cured, an equal upward and downward pressure is applied. From the test, the load-upward deflection curve in side shear and the load-downward deflection curve in end bearing are drawn. Typical curves are shown where the ultimate load in side-shear is reached and where the ultimate load in end bearing is reached. Several examples of tests in which the test load reached ultimate loads far in excess of what was expected are shown. The side shear in rock sockets is shown to be much larger than generally estimated. Examples are given of where side shear is smaller than expected and the reasons discussed. Disturbance of the sides of drilled holes due to poor construction techniques and ways to avoid these conditions are considered. Examples of bottom hole disturbance are given and ways to prevent the disturbance are discussed. A graph showing the actual measured capacity of drilled shafts compared to the estimated capacity as a function of the hardness and strength of the soil or rock is presented.

Jan 1, 1999

By J. E. Nesset

"I had been requested earlier this year by MetSoc, our sister society of CIM, to contribute a chapter on technical developments in Canadian mineral processing over the past 50 years to their 50th Anniversary volume. Accepting the challenge of assembling such a chapter seemed at first a reasonably straightforward task, until one realises that the list of contributions by Canadians to mineral processing over this period has been more than just significant. It turns out to have been an extraordinarily fertile time for innovation and impact for Canadian-based technology. The list is necessarily a subjective one, however I had no trouble identifying twenty technology developments that are clearly outstanding, and there are undoubtedly others. As much as possible, I approached the individuals themselves who played key roles in each technology and asked that they tell the “story”. Without exception, all who were invited accepted eagerly and delivered more than I had hoped for. The technologies have been grouped into those that are truly Canadian innovations, such as the Knelson gravity concentrator and the McGill gas dispersion sensors in flotation, and technologies where Canadians and Canada played a very significant role in their success and implementation, such as AG/SAG grinding and ion-beam surface analysis. Also included are what may be termed technology transfer initiatives and institutions that have risen to a world class level, such as SGS Lakefield and the Canadian Mineral Processors Society of CIM. The challenge is now for the coming generation to continue this record of innovation and contribution to the industry, and that includes the (mostly) Canadian mining and metallurgical companies who have taken the longer term view and supported many of these initiatives, through their critical early years, with both financing and project sites for these ideas. Let us hope that the current trend of mining company globalization will not dampen their enthusiasm to participate. This plenary presentation will highlight many of these technologies, the individuals behind them, and their significance to the mineral processing industry."

Jan 1, 2012

By M. Mirnezami, D. Lascelles, J. A. Finch, E. El-Ammouri

"In a previous publication, the depressant action of Mg above pH 10 on Cu-activated sphalerite was described (Lascelles et al., 2001). In the present communication, a second role, aggregation is introduced.Aggregation (i.e., the tendency of particles to cluster) is measured using settling rate and turbidity converted to an aggregation index (AI) where 0 corresponds to dispersed and 1 to aggregated. Surveys of Cu and Zn flotation stages at four concentrators showed the A1 increased significantly above pH 9. The metal ions identified in the process waters, principally Ca and Mg, were tested to determine which might be responsible. The presence of Mg was found to be the most important, 50 ppm Mg having a greater impact than 500 ppm Ca fkom pH 9 to 1 1. In one plant, poor repeatability in A1 was suspected to be related to varying Mg levels; doping with Mg significantly increased AI.In both aggregation and depression, therefore, the common feature is the impact of Mg at pH > 9. Over this pH range Mg forms a range of hydroxy species, including Mg(OH)2 precipitates. Suggested aggregation and depression mechanisms associated with these precipitates are introduced. Possible problems and opportunities arising from the findings are discussed.INTRODUCTIONProcess waters in flotation circuits contain a variety of metal ions that may introduce unwanted activation or depression. Two common metal ions are calcium and magnesium. Typical concentrations are in the range 50 ppm Mg and 500 ppm Ca (Marticorena et al., 1994, Basilio et al., 1996, Negeri et al., 1997, Nesset et al., 1998)."

Jan 1, 2002

By M. J. Nicol

Mr Vegter has analysed, in some depth, the approximations made in the treatment of the kinetic data presented in the original by ourselves (ref.1) and has come to the conclusion that ?under the experimental conditions used by Adams and Nicol (1986) the steady-state assumption was inaccurate?. We are acutely aware of the fact that the experimental method adopted does not permit the attainment of a true steady-state in the elution reactor. However, this does not eliminate the attainment of a pseudo steady-state by a suitable choice of the experimental parameters with the accompanying simplification of the analysis of the data with the aim of drawing the reader?s attention to the most important objective of the paper viz. the effect of various operating parameters on the rate of elution of gold.

Jan 1, 1997

By R. M. Lamya

The leaching behaviour of nickel?copper matte in an acidic?copper sulphate solution during the repulping stage at Impala Platinum Refineries has been studied. The base metal recovery process consists of a matte repulping stage prior to a series of pressure leach stages. Therefore, the repulping stage is basically an atmospheric leach stage in which the matte containing mostly Niand Cu is leached in copper-spent electrolyte from the tank house, resulting in dissolution of nickel and precipitation of almost all the copper. To understand the nature of the leaching process during this stage of the operation, the effects of temperature stirring rate and matte particle size on the rate and extent of base metal dissolution and copper rejection from the solution have been investigated. The leaching mechanism of the matte in the investigated system is alsoproposed.

Jan 1, 2006

By Fred S. Karn

Inhibitors are used in coal mines as a precaution against accidental dust explosions. Although rock dust is the usual inhibitor many others have been tested. To facilitate testing a screening process using laser irradiation was proposed. The procedure includes irradiation of a coal-dust mixture followed by mass-spectrometric analysis of the evolved gases and an evaluation of the flammability characteristics of the gases. Carbonate-type inhibitors decreased the percentage of combustibles in the gases generated and inhibitors like NaCI (thermally stable salts) decreased the total gas generated. A suitable test procedure did not result from the investigation, demonstrating the inadequacy of fast heating, non-combustive techniques in rating inhibitors of coal dust explosions.

Jan 1, 1973

By Garry Keizer

The Cortez gold mine is located in Lander County, NR, about 130 km (80 miles) southwest of Elko. Cortez Gold Mines (CGM) is a joint venture between Placer Dome US Inc. (60% operator) and Kennecott Corp. (40%). The claims that supply oxide and refractory ore feed to the Cortez milling facility are located in both Lander and Eureka counties. These include the Cortez and Horse Canyon deposits, all operated by the joint venture. Other deposits outside the CGM claim area include Fire Creek, Buckhorn, Gold Bar and Tonkin Springs. These deposits all occur along the Battle Mountain-Eureka Trend. History Mining in the Cortez district began in 1862 with the discovery of high-grade silver ores. Grades in the hundreds of ounces per ton occurred in an area 7 km (4.5 miles) southeast of the current CGM mill site. Underground mining through the Garrison and Arctic tunnels provided the bulk of the ore production between 1864 and 1895. To a lesser extent, the Mill Canyon area also supplied ore until 1930.

Jan 1, 1993

Sphalerites from Devonian cassiterite-sulphide deposits and Pb-Zn-Ag fissure veins have similar ranges of Cd contents, but the average Cd and Fe contents could indicate a small initial difference in availability of Cd between the Zeehan-Renison Bell district and the Mt. Bischoff-Waratah district. Sphalerites from banded Pb-Zn deposits (Rosebery and Hercules) are characterized by low Cd content which is a world-wide feature of such deposits in exIrusive rocks, and may indicaIe a genetic relationship between ore deposition and vulcanism.

Jan 1, 1968

By J. H. Zietsman

It has previously been observed that industrial high-titania slags display a compositional invariance, remaining close to stoichio-metric M3O5. The present study focuses on this invariance and the phenomena which may cause it. The invariance was studied using thermochemical calculations and a mechanism is proposed for the observed behaviour. The mechanism suggests that a combination of thermochemical equilibrium and transient slag solidification and melting results in the observed compositional invariance. The proposed mechanism provides new insights and prompts questions about other mechanisms in the smelting process.

Jan 1, 2004

By W. W. Agey

The Bureau of Mines examined and tested the rhodonite deposits of the Silverton lead-zinc district, San Juan County, Colo., as a possible source of domestic manganese. Exploration and development work by several mining companies and preliminary reconnaissance of the area by Bureau of Mines engineers indicated the presence of extensive manganese resources in the form of rhodonite. This report summarizes the results of laboratory beneficiation tests made on samples of different type and grade material obtained from surface and underground exposures of seven veins in the district. Surface and underground examinations revealed the presence of several prominent veins that could be traced up to 2 miles for a single vein along the surface. The principal veins average about 50 feet in width and apparently carry rhodonite to considerable depth. Underground samples were taken from the Sunnyside, Silver Queen, Washington, Independence, and Scotia veins. Samples also were taken from surface exposures of the Sunnyside Extension and Hidden Treasure veins.

Jan 1, 1962

By Mark K. Larson

Calibration of LaModel for deep coal mines begins with adjustment of overburden stiffness for load transfer distance. This calibration determines whether mining induced stresses are concentrated in the immediate abutment of the gob, or spread over a wider area. In the absence of site information, an empirically-based estimate is often used. Where data is available, a recommended calibration procedure can be followed, as is done in this case study at a deep western longwall mine, with minor modifications and extensions. In this case, data sources included borehole pressure cells, flatjacks installed in series with support Cans, and observed changes in ground conditions. Calibration was based on the first detection of mining-induced stress from the advancing longwall. Detection was found to depend on the type and sensitivity of measurement. Borehole pressure cell data with a 20-psi-increase detection threshold were chosen as the standard, in accord with data used in deriving empirical relationships. Application of this standard produced a load transfer distance estimate roughly four times the empirical relationship developed by Peng and Chiang (1984). This is a significant deviation with important implications for panel design at this site. Data from flatjacks, ground condition observations, and borehole pressure cells with higher threshold values, were tightly clustered and show load transfer distances from two to four times empirical guidance. Ratios between various measurements can be used to adjust measurements to the standard (although they may depend on mine geology). Once established, ratios can be used to adjust estimates, say from support flatjacks or ground observations, to the standard, where borehole pressure cell data is not available.`

Jan 1, 2012

By Marco A. Vera

"This paper investigates the froth function in flotation and the associated upgrading process. Flotation literature has revealed that one of the main functions of the froth phase is the cleaning of bubble-particle aggregates by rejection of entrained material. The cleaning and transport processes across the froth phase exert straining forces on these aggregates on their way up to the froth surface. These forces will impact on the recovery of bubble-particle aggregates.The grade at the top of the froth (TOF) is a parameter related to the quality of particles collected by bubbles in the pulp zone (true flotation). It has recently been demonstrated that TOF corresponds to the maximum practically attainable grade described by the recovery-grade (or enrichment ratio) curve. TOF lumps all the processes experienced by the bubble-particle aggregates before reaching the launder concentrate. This paper describes a methodology for quantifying flotation performance by means of the top of the froth sample - a touch of froth.INTRODUCTIONFroth flotation may be the most important mineral processing technique, but its theory is complex and is not completely understood even though many aspects have been studied and reviewed (Teague, 1998; Wills, 1992).Two distinct particulate systems prevail in the flotation process: a pulp phase and a froth phase (Figure 1). The pulp zone had been studied extensively; however, it is only recently that techniques to measure the froth zone performance have been developed (Contini et al., 1988; Falutsu and Dobby, 1992; Feteris et al., 1987; Seaman, 2002; Vera et al., 1999b).Flotation involves a number of mass transfer processes, occurring in the pulp phase and the froth phase. The formation of the froth and its subsequent removal are considered to be two important steps of the process. Phenomena that occur in the froth phase are known to affect flotation performance significantly (Cutting et al., 1981).Because the froth has a high free surface energy (as a result of the extensive interfacial surface between liquid and air), it appears thermodynamically unstable. The foaming is a dynamic balance, as new bubbles are added continuously from the pulp, while others disappear from the top. Under steady-state conditions, the volumes of added and subtracted air are equal (Booth, 1953)."

Jan 1, 2003

By Adam Shang Robert Fu

The Yung-Chung-Tunnel in Taiwan, constructed for the Taiwan-East Railway Bureau, collapsed during construction when a water bearing, fractured marble zone was intersected. The inflow was approximately 4,000 liters/second. In spite of 30 relief holes the total inflow into the tunnel remained constant. The pre-excavation grouting through the re-aligned tunnel had to be conducted under extreme flow-conditions. A hot bitumen grouting program was selected for technical and economical reasons out of 13 international proposals. The technical challenges were: grouting under severe flow conditions high formation water pressures to be injected with hot bitumen at high temperatures and pressures The hot bitumen grouting program resulted in a dramatic reduction in the hydraulic conductivity and stabilization of the formation and facilitated a problem-free excavation.

Jan 1, 2007

By Thomas E. Lobb, Harry C. Verakis

This article examines the factors related to injuries due to inadequate blasting shelters and blast area security, and identifies mitigation techniques. The key concepts are:(a) accurate determination of the bounds of the blast area, (b) clearing employees from the blast area, (c) effective access control, (d) use of adequate blasting shelters, (e) efficient communications, and (f)training. Fundamentals are reviewed with an emphasis on analyzing task elements and identifying root causes for selected blasting accidents. Mitigating techniques are presented along with discussions and examples.

By C. Vipulanandan

It is critical to monitor the ground conditions during excavation and drilling of boreholes during construction to identify possible changes in the soil and rock formations. Drilled shafts are increasingly used as foundations to support structures, bridges and other facilities in geomaterials such as soft-rocks and hard clays. Locating the bottom of the borehole during construction with the required design strength is critical. Hence developing a simple device that could be easily adapted/used with the drilling tool was of interest in this study. Determining the shear strength of the geomaterial in the borehole and at various elevations including the bottom of the borehole can lead to better quality control of construction by identifying the various layers based on strength. In this study, a down-hole penetrometer (DHP-CIGMAT) was designed, built, calibrated and tested in the field to determine its effectiveness in measuring the strength of soil/soft rock in the boreholes. Based on limited field tests, linear correlations between geomaterial strengths and DHP-CIGMAT deflection have been developed. The DHP-CIGMAT can be used to identify soils and soft rocks.

Agglomeration for Copper Heap Leaching Agglomeration of ore is a method which can be used to eliminate the migration of fine grained particles throughout a leach heap. Without agglomeration, fine ore particles are able to migration within the heap, clogging flow channels and producing large areas where access of the solution is poor. In order to gain the benefits of agglomeration and improve agglomerate strength even further in copper heap leaching, an economical, acid-resistant binder is needed. However, most binders have been used without any systematic reasoning. A set of novel testing methods were developed, including a soak test, percolation flooded columns, and larger long-term leach columns. The soak test compares the degree of breakdown when agglomerates are subjected to an acidic environment. While the percolation flooded columns and larger long-term leach columns evaluate the flow of leach solution throughout the ore bed. Systematic studies have been completed on a wide range of binders using these novel testing procedures. It was found that for a low grade chalcocite ore, which was rich in silica, from a southwest US mine, polyacrylamides reduced the fines migration the best in the novel soak test. The non-ionic binder, in particular, was found to reduce fines migration as much as 93 per cent. Several of the binders tested were shown to increase the hydraulic conductivities of the agglomerated ore up to 2.5 mm/sec, compared to a hydraulic conductivity of only 0.25 mm/sec when no binder was used. These binders also prevented 'slumping' of the ore, which indicates a decrease in breakdown of the agglomerates. The use of a binder also showed no interference with leaching reactions in long-term leaching experiments.

Sep 13, 2010

Council for 1998/99 President R.P. Mohring President Elect J.R. Dixon Vice Presidents Senior junior M.H. Rogers Dr L.A. Cramer Immediate Past President Honorary Treasurer Dr N.A. Barcza J.A. Cruise

Jan 1, 1985