Search Documents

Various steps, and complete sequences, for the recovery of lead and zinc from a mixed sulphide concentrate, high in silica and pyrite, have been tested.Oxidation steps of roasting in air or in a sulphating atmosphere and use of aqueous acidic, ammoniacal, and near neutral oxidation media were compared. Oxidation roasting or use of acidic media appeared most useful. Procedures for dissolution of zinc from calcines using sulphuric and sulphurous acid to avoid silica gelation problems are compared and a direct leaching procedure with sulphuric 'acid at controlled pH shown to be the most useful.Methods for the removal of germanium, nickel, and magnesium from zinc sulphate solutions prior to zinc electrodeposition were tested. The recoveries of zinc from ammoniacal solutions by electrolysis and distillation are compared.The dissolution of lead compounds from the residue of zinc extraction by amine and ammoniacal ammonium sulphate (AAS) solutions Was tested. Lead, sulphide was precipitated in filtera'ble form from AAS solutions. The reduction of lead sulphate to lead sulphide with sulphur was difficult, but possible. The various steps were used to deveiop five complete processing sequences, of which two were shown to be technically feasible and have potential economic viability.

Jan 1, 1975

By Alfonso W. Ovalle

INTRODUCTION The block-caving mining method is one of the most economical ways existing today to extract ore from nature. It is undoubtedly the least costly of the underground systems and moreover it compares favorably to open-pit mining. In addition to its low cost characteristic, the block-caving mining method permits a great extraction volume as can be exemplified by El Teniente's output capacity of over 22 million tons of ore per year. These characteristics of block-caving give assurance that, even though it is a very old mining system, it will be a good answer to the many future large massive low ore grade deposits to come and a1 so to rep1 ace open-pi t mining as such operations get deeper with higher stripping ratios. These are the reasons that induce further study of block-caving. In this paper block-caving at El Teniente is analyzed with due consideration to the major problems that this mine will encounter. Emphasis is given to the factors influencing the mining of soft ore which accounts for most of the ore to be extracted in the next ten years. A separate paper is devoted to a major modification introduced to block-caving hard primary ore at El Teniente by means of LHD equipment extraction. DESCRIPTION OF THE PRESENT MINING Ore Production and Flow Over 62.000 tons per day of ore are extracted 359 days per year at the El Teniente Mine. The Teniente 8 train haulage level at 1.983 m takes 29.000 tons daily to the Col6n Concentrator. Two trains make the 8 km haul with 16 cars per train. Car capacity is 90 tons. The Teniente 5 train haulage level 298 m above takes 33.000 t per day to the old Sewell Concentrator. Ore is produced from three production areas in two different levels. The so called North Mine produces 42.000 tons daily from the Teniente 4 level 65 m above the Teniente 5 haulage level. The Central Mine produces 1.000 tons from the first hard rock block caved at the Te- niente 4 level. The combined 43.000 tons per day production is sent through inclined 2 m dia- meter raises to the Teniente 5 haul age level , where 33.000 tons are taken 2.5 km to the Sewell Concentrator and 9.000 tons are hauled 0.5 km to a 5 m diameter vertical ore pass which sends ore to Teniente 8. The haulage is by 7 trains, 15 gabble-bottom cars per train. Car capacity is 20 tons. The so called South Mine produces 19.000 tons per day from the Teniente 1 level 645 m above the Teniente 8 haulage level. Ore is transferred by 2 m diameter inclined raises to the Ten 1 Retram level 22 m below, where 5 trains with 20 Sandfor Day cars per train, 8 tons capacity per car, haul the ore 1.5 km to two vertical 5 m diameter ore passes which connect to Ten 8. Starting in 1982 the Central Mine will in- crease production to 6.000 tons per day. An in- dependent loop haulage system will start operat- ing at the Teniente 5 level to feed a new under- ground 1.372 mm (54 in.) gyratory crusher which will send minus 152 mm ore (9 in.) to Teniente 8. In two or three years time the North Mine will only feed the 33.000 tons to the Sewel 1 Concentrator with its old Teniente 5 haulage system. The Col6n Concentrator will be fed from the Central and South Mines. Figure 1 shows the transfer systems and ore flows. The Ore Body In plan view at the Teniente 4 level the ore body has a kidney shape 1.800 m long and between 400 to 700 m wide. The north-eastern section of the ore body was washed away by the Teniente River. At the Sub 5 Level, 125 m below Teniente 4, the mineralization completely surrounds the circular 1.000 m diameter steep-sided barren breccia pipe (Braden pipe) . The ore body rock is 73% andesite, 14% diori te, 13% dacite and 6% mineralized breccia. Most of this ore is secondary enrichment sulfides which apart from the dacite is strongly fractured being chal cocite, cove1ine , bornite and

Jan 1, 1981

By L. F. Mondolfo

An aluminum-copper 4 pct Cu alloy aged at room temperature for times increasing up to 78,000 hr was annealed at 170°C and the hardness and electrolytic potential determined during retrogression and subsequent aging. It was found that there is a change of behavior with increasing time of aging at room temperature which indicates that, given sufficient time, retrogression disappears and the room-temperature aging tends to progress directly into the high-temperature aging. WHEN an age-hardenable alloy is aged at low temperature after proper quench, changes of properties and structure take place. If this material is then heated to a temperature higher than the previous one, but still well below the solution-treatment temperature, the properties and structure changes produced by the low-temperature aging disappear and the material apparently reverts to the as-quenched condition, ready to undergo aging from the start. This phenomenon is termed reversion or retrogression. First discovered by Cayler3l it has been extensively investigated, as shown by the number of publications listed in the bibliography. From all the information available the following facts emerge: 1) All aeg hardenable alloys can be retrogressed.9 13, 19) 24, 33, 41, 42, 44, 47, 53, 54, 61, 63, 64, 66, 73, 78 2) All the properties changes that take place during aging at low temperature can be retrogressed to a smaller or larger extent.4,5,7,12,19,32,49,50,57,58,60,67,75,76 67, 75, 76 3) Retrogression requires that the temperature be well above the preliminary aging temperature. If the difference between the two temperatures is small, Little or no retrogression takes place.7,20,32,33,41,49 57. 65 4) The larger the difference between the preliminary aging and the retrogression temperature, the faster and more complete is the retrogression.20, 33, 41, 48, 65, 67 5) Retrogression can be produced several times in the same alloy.23, 35,41,57,59 6) The amount of retrogression that can be obtained depends on the aging temperature. Alloys aged at the lower temperatures can be retrogressed the most. The higher the preliminary aging temperature the less retrogression can be produced.20,25,33,37,44,49,54,58 7) Appreciable retrogression after aging at elevated temperatures is possible only if the preliminary aging has lasted a short time. After a certain time of aging at high temerature retrogression does not take place any more,:5,6,9,10,11,21,40,58 8) During retrogression the Guinier-Preston zones redissolve and disappear. The other precipitate

Jan 1, 1960

By Parkhurst D. H

It is shown that a differential colorimetric technique can be used as a routine method for the estimation of titanium in beach sands, and their ore dressing products. The method will tolerate the presence of most of the other elements usually found in beach sands. The accuracy is shown to be within the limits of ±0ò31 per cent for concentrates containing more than 95 per cent titanium dioxide and ±1 per cent for tailings containing 0ò2 per cent titanium dioxide. The method is described for use with a Hilger "Spekker" absorptiometer.

Jan 1, 1957

By B. B. Dhar

Slope stability at the proposed mine in Rajasthan was analysed in two dimensions using a finite difference code. The properties of the rock material were determined in the laboratory and subsequently modified to approximate those of the in situ rock mass. Geotechnical mapping was undertaken to determine the critical orientation of structural discontinuities. The results of the work indicated that an open pit 148 m in depth would be stable with overall slope angles of 60 degrees

Aug 1, 1994

By B. Weyerman

U. S. Steel's Oak Grove Mine experienced several top hinge failures on their caving shields. It was determined that all the caving shields needed to be replaced with new caving shields before more thilures occurred. The cost and amount of time needed for several scenarios of caving shield change outs were compared. This paper discusses how Oak Grove Mine decided to and did change 126 caving shields in six specially designed jig stations underground during a longwall move using their own UMWA employees.

Jan 1, 2001

By D. A. Greenwood

Dr David Greenwood opened the first technical session of the conference by highlighting the diverse nature of the papers in this session but drawing attention to the common theme that each solved a particular problem. PAPER 1.1 Tony Elliott introduced his paper on deep mix-in-place soil/cement stabilisation by stressing its simplicity. The engineering solution adopted at Elland was detailed in his paper and had formed the key to success of the project. The process itself is not widely used or known in the UK, although it has the potential to achieve significant benefits, subject to proper engineering control being exercised. It was explained that although the concept was not new, development of the technique for soil modification was relatively recent. The alternatives to mechanical mixing are injection, which is very dependent on soil type, site geometry, etc, and jet grouting; both processes are soil-responsive, and not easily monitored or programmed, difficulties which can largely be overcome by mixing. To achieve this at depths to say 30m requires high-powered, high torque machines and has resulted in significant equipment development.

Jan 1, 1991

By R. Ward Stahl

Fire is still a scourge of the mining industry, although many precautionary measures have been and are being taken to reduce the incidence of fires and to combat them. Generally, the success of fire extinguishment is directly proportional to the speed of attack, and the speed of attack in turn is dependent upon the availability of materials and trained personnel. Preparations for firefighting are frequently neglected because they are considered emergency needs and do not contribute directly to coal production. Fire incites panic--a fact often overlooked--but such chaos can be minimized by training people in the use of equipment and procedures. Heat, smoke, and fumes hamper the approach to a fire; however, a relatively new technique of attacking fires with high-expansion foam may well contribute greatly to firefighting. The foam is transported to a fire and used at a considerable distance, thus permitting the firefighters to work more safely.

Jan 1, 1962

By Huang Zhiwei, Paul Skayman, Kevin Holley

In 1989 The First Brigade for Geology and Mineral Exploration of Qinghai Province discovered gold at Jinlonggou and Qinlongtan, Tanjianshan. Between 1992 and 2002 small scale mining was carried out at these sites using underground mining methods at Jinlonggou and an open pit at Qinlongtan. During 2003 and 2004 geotechnical investigations were carried out in support of a bankable feasibility study. An important objective of this investigation was to meet both internationally accepted standards and codes of practice, and also to satisfy the Chinese requirements. Extensive use of local experience was utilised. Where possible geological drilling information was incorporated into the assessment. Extensive geotechnical mapping of surface and underground exposures, and index testing to gain an appreciation of rock intact strength were used to characterise the sites. Rock mass classification (MRMR) was used to assess indicative overall slope angles and appropriate bench stack heights for the proposed pits at Jinlonggou and Qinlongtan. Measured discontinuity orientations were used in kinematic analysis to assess stability of possible pit slope geometry at a batter and overall scale to provide preliminary recommendations for the pit slope configuration. Numerical modelling was also carried out to improve the understanding of anticipated pit behaviour. Site investigation and preliminary geotechnical design details, that incorporate site specific conditions for the formation of open pits at Tanjianshan, are discussed in this paper.

Jan 1, 2006

By Mark H. Balfe

Over the last decade, Fenway Park has undergone annual improvements to modernize the facility for players and fans. These renovations include the Monster Seats, the Right Field Roof expansion, a new pavilion behind home plate, expansion of the Red Sox clubhouse, additional roof seating, and concourse improvements. Retrofitting the historic ballpark to bring it up to current standards required installation of foundations to support the new structural loads for each of the alteration projects. This required evaluation of existing conditions, and in many cases augmentation of the foundations at existing columns to accommodate the structural changes to the park. New foundations, generally consisting of drilled-in micropiles, were installed in numerous configurations and conditions. Since 2003, a total of 215 drilled-in micropiles have been installed to augment various columns around the park. The micropiles range in capacity between 40 and 70 tons and are installed through Fill and Organic Soils and embedded into the dense Glaciofluvial Sand and Gravel layer. Issues and learning related to the foundation augmentation include schedule constraints (work is typically conducted during the off-season and schedule is very aggressive), encountering old/abandoned utilities or foundations, ventilation of equipment, and management of spoils during micropile installation.

Jan 1, 2011

By D. R. Wardrop, G. Walton

Paper presented at the UK minerals industry conference held in Leeds, UK, 3-5 April 1995. A description is given of the approach that has been taken to the design of the 550 000 000 t superquarry with a planned life of 60 years that is proposed for development. The quarry has been designed to replicate a corrie and a sea loch and will include excavated slopes more than 570 m high. The main geological and physical controls on the layout and the choice of development method are outlined. The operation phasing is presented and the geotechnical constraints on slope design and the feasibility of alternative quarry limits are discussed. Environmental considerations have been dominant in planning and the quarry has been specifically designed for closure

Jul 1, 1996

By S C. Dominy

Various styles of gold mineralisation pose problems during sampling because of their complex gold grade distribution and presence of coarse gold. Effective sampling and sample preparation forms the basis of resource estimates. The design of a sampling and assaying protocol must be based on a thorough understanding of the mineralisation in question, which should include consideration of gold particle size and mass distribution. The proportion of coarse gold within samples has a profound effect on the requirements for sample preparation and assaying. Choice of preparation procedure and assay type is of critical importance if sampling errors are to be minimised. Traditional fire assays, using small charge sizes, often understate assays gained from large charge sizes and techniques such as screen fire assay and LeachWELL. Proper application of the Theory of Sampling reduces errors during collection, preparation and assaying. A quality control/quality assurance program must be implemented and critically assessed. A case study from the Ballarat mine is presented, which is characterised by substantial quantities of coarse-gold hosted in quartz veins. Diamond core drilling is the key input into resource delineation. A number of different sampling and assay options have been trialled over the recent project history. The current sampling protocol utilises whole drill core, using LeachWELL assays after logging and photography.CITATION:Dominy, S C, 2017. Sampling coarse gold-bearing mineralisation – developing effective protocols and a case study from the Ballarat mine, Australia, in Proceedings Eighth World Conference on Sampling and Blending , pp 71–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Marcial Medina

El presente texto describe la reología de la Pulpa a nivel de química de superficie y así sugerir las alternativas a los problemas que impiden poder operar en forma continua y su capacidad de diseño la Planta de Flotación Diferencial de Cobre – Molibdeno. Asimismo, es necesario definir una solución a escala de laboratorio, la cual debe ser validada con pruebas industriales e implementarla en planta. La estrategia debe garantizar la continuidad de la operación de la Planta de flotación de Molibdeno con cualquier tipo de mineral y que no presente compactación la pulpa. Finalmente, se devbe agarantizar el procesamiento de toda la producción de la planta de cobre en la planta de flotación diferencial de cobre molibdeno.

Sep 12, 2011

By W J. Rankin

Metals are well suited to sustainable development goals. They are not biodegradable and have virtually an unlimited lifespan and the potential for unlimited recyclability. Thus metals can be considered as renewable materials. However mineral resources, the source of primary metals, are ænon-renewableÆ as their supply is finite, but this does not necessarily mean scarcity. In this paper the results from a series of Life Cycle Assessments of primary metal production processes for copper, nickel, lead, zinc, aluminium and steel have been used to examine how metals may contribute to societyÆs transition to sustainable development. Particular issues considered include:current metal reserves and how these may change in the future; some of the environmental impacts (Total Energy, Global Warming Potential and Acidification Potential) associated with primary metal production and how they will be exacerbated by declining ore grades; new processing technologies with lower energy consumptions and improved metal extraction efficiencies that will reduce reserve depletion and environmental impacts; increasing the utilisation of æmetals in useÆ by recycling, with particular reference to aluminium; and the potential impact of a carbon tax on metal prices and how this may influence the ways in which metals are used in the future.

Jan 1, 2002

By Kristie Tarr

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

Oct 1, 2010

By T. P. Lim, J. A. Cherry, A. J. Vivyurka, R. D. Blair

The first phase of an investigation of the chemical composition of subsurface water and the hydrochemical processes in and near the abandoned Nordic tailings at Elliot Lake, Ontario, was conducted in 1979. The Nordic area, which covers 85 hectares with an average thickness of 10 m and overlies deposits of permeable glaciofluvial sand, contains 15 million tonnes of tailings with 4-7% pyrite. Nests of standpipe piezometers installed at three locations on the tailings indicate that seepage through the tailings is predominantly downward. The water table in the tailings slopes from the north side of the tailings dam, where it is within a metre of surface to the south side near the tailings dam, where it is approximately 10 m below surface. When they were deposited during the period from 1957 to 1968, the tailings contained pore water at a pH of about 8 resulting from neutralization treatment in the mill. At the three piezometer nests, the pH increases from 3 near the water table to 7 near the bottom of the tailings. The pore water in the tailings is gradually becoming acidic because of oxidation of pyrite in the zone above the water table. The concentrations of Fe, Mn, Ni, Co, Zn and Pb are high in the shallow acidic zone and much lower in the deeper neutral zone. Concentrations of 226Ra range from 30 to 230 pCi/L. At the three sites concentrations of major ions in the permeable sand a short interval beneath the tailings indicate 226Ra presence of tailings seepage, but Ra concentrations are only 2 to 8 pCi/L. Greater downward penetration of 226Ra probably occurs in the area closer to the tailings dam. Monitoring of a network of multilevel bundle piezometers installed in permeable sand that extends southward from beneath the tailings indicates the occurrence of a plume of tailingsderived water containing high concentrations of Ca, Mg, Fe and S04 that extend 400 m downgradient from the tailings dam. The total dissolved solids decline from 20,000 at the dam to less than 500 mg/L at the identifiable downgradient periphery of the plume. A much smaller but distinct plume of water with high heavy metal concentrations and 226Ra in the range of 10 to 130 pCi/L extends from beneath the dam for a distance of 15 m. The pH of the groundwater in this heavy metal-radium plume is 4 to 5, whereas elsewhere in zone of groundwater with high dissolved solids, the pH is above 6. The results of this investigat, suggest that the heavy metals an 226 Ra are relatively immobile in the perme-

Jan 1, 1980

By Paul M. Ambrose

THE ABRASIVES INDUSTRY throughout the world enjoyed a profitable year. With the exception of tripoli, the quantity of each kind of abrasive produced in the United States was greater than for any of the past 5 years and value of each was greater than for many years. Production of silicon carbide both in the United States and in Canada was the largest since 1960. Abrasive machining, which offers great potential for the increased Use of aluminum oxide, contributed to increased industrial productivity. Diamonds from the sea off the coast of South-West Africa attracted wide interest. Much of the production from this source has been gem diamond, and there is little likelihood of significant quantities of industrial diamond from that source. Manufactured diamond from all free-world sources was sold in the United States in 1964.

Jan 1, 1965

By Luke Erickson

San Francisco Public Utilities Commission is planning to replace 5 miles of pipeline under San Francisco Bay. The tunnel will be constructed using an Earth Pressure Balance (EPB) TBM and will be the first TBM-driven tunnel under the Bay. The alignment passes under environmentally sensitive habitats, through interbedded layers of sands and clays, and through a buried bedrock ridge. This paper discusses the geotechnical characterization and anticipated tunneling conditions and presents the analysis of various construction methods that resulted in the selection of an EPB TBM. Considerations related to tunneling with an EPB TBM are described in detail, including ground conditioners, TBM cutterhead wear, muck control, and squeezing ground.

Jan 1, 2008

By Charles Pretorius, Henk Ludik

Navachab Mine experiences difficulties with pit wall stability in certain areas of the mine. The main reason for the instability is the fact that the geology comprises many joints and faults. Blasting, without impacting negatively on the stability of the pit walls, poses a major challenge.

Jan 1, 2006

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1941 are available at Institute headquarters, unless otherwise noted They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS TECHNICAL PUBLICATIONS in Classes A-Metal Mining, 13-Milling and Concentration, H-Industrial Minerals, and I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month Technical Publications in Classes C-Iron and Steel Division, D-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly TECHNICAL PUBLICATIONS in Class G-Petroleum Division are distributed in PETROLEUM TECHNOLOGY, which is issued every other month TECHNICAL PUBLICATIONS in Classes F-Coal Division, J-Mineral Industry Education Division, K-Mining Administration, and L-Geophysics, are issued as separate pamphlets An Institute member is entitled to one copy of any printed TECHNICAL PUBLICATION or CONTRIBUTION Copies of TECHNICAL PUBLICATIONS listed have been mailed to members of the Institute according to their registration by classes CONTRIBUTIONS and other TECHNICAL PUBLICATIONS will be sent upon request A member may purchase an additional copy of a TECHNICAL PUBLICATION or a CONTRIBUTION at one cent a page, minimum charge, 25¢ Nonmembers may purchase any CONTRIBUTION or a TECHNICAL PUBLICATION of the F, J, K, or L classes at the same rate, but the nonmember price per copy for METALS TECHNOLOGY, MINING TECHNOLOGY or PETROLEUM TECHNOLOGY is $1 25 domestic, $1 35 foreign countries. TECHNICAL PUBLICATIONS (separate pamphlet form), $2 per annum domestic, $2 50 foreign. METALS TECHNOLOGY, $7 per annum domestic, $7 80 foreign (Iron and Steel Division and Institute of Metals Division ferrous and nonferrous papers) MINING TECHNOLOGY, $6 per annum domestic, $6 60 foreign (metal mining, milling and concentration, Industrial Minerals Division, and mining geology papers) PETROLEUM TECHNOLOGY, $6 per annum domestic, $6 60 foreign Bound volumes have been mailed to members that have requested them, and MINING and METALLURGY Is mailed each month A member is entitled to one volume a year on his membership and he may purchase for $2 50 one copy of a volume not already received, additional copies of the same volume, $5 Nonmembers in the United States may purchase the volumes listed at $5 each, outside of the United States and its possessions, $5 6o Extra single copies of MINING AND METALLURGY, 25¢ current issue, back numbers 500 each to members, to nonmembers 50¢ current issue and $1 each, back issues Subscription price to nonmembers and to members for extra copies, $3 per annum domestic, $4 00 foreign.

Jan 1, 1941