Search Documents

By Damon P. Vandermaat

Coupon testing allows for the rapid understanding of a material?s likely behavior in service conditions, allowing engineers and operators to make informed decisions about the likely service-life of parts when subjected to field conditions. Bend testing has been identified as the best approach for exploring rock bolt susceptibility to stress corrosion cracking (SCC) in underground mining. The bend test specimens used were 2?3 mm thick slivers of steel, cut from the outer edge of a rock bolt. For the specimens, 1350 grade steel was chosen due to its wide use in the industry. The jigs themselves are small assemblies made of stainless steel that are capable of imparting a bending load on the specimens. The jigs were installed at a coal mine located in the Western Coals West of Sydney, Australia, in such a way as to expose the test specimen to water dripping from the mine roof. It is expected that this approach will yield results pointing to the likely SCC mechanisms affecting the service life of rock bolts, as well as demonstrate the jigs? usefulness as an early warning system for SCC. Furthermore, the coupon tests will be correlated against the results of large-scale laboratory tests.

Jan 1, 2012

By Bure R

Approximately 2.4 million ounces of gold and 11.3 million ounces of silver have been produced from the Umuna Lode by Misima Mines Pty Limited between June 1989 and the end of Decemeber 1996. Reserves remaining at the end of December were 32.1 million tonnes at 1.0 gram per tonne gold and 9.7 grams per tonne silver. To attain precious metal production of this volume, an estimated K60,000,000 (1996 Kina) was spent on exploration alone. from the 1940s to the present day. Exploration expenditure for the 1996 calendar year was approximately K4,400,000. With such a large investment in exploration, large quantities of data were generated and stored in various forms. To make best use of this data, it was necessary to organise and systematically store this data in a form compatible with a modern Geographical Information System (GIS). The Umuna Lode on Misima Island is a low sulphidation gold- silver deposit dated at 3.5 ¦ 0.2 Ma. The deposit is controlled by the 50 to 100 metre wide Umuna Fault- a moderate dipping, brecciated clay- chlorite- carbonate altered, normal fault zone. There is approximately 230 metres of mostly dip slip offset on this fault, which is measurable by the offset of the Cretaceous schist, marble and greenstone host sequence. Late Miocene microdiorite spatially related to the Umuna Lode does not appear to be genetically related to the gold- silver mineralisation. GIS was introduced to Misima at the end of 1995 and until recently has been mostly used for data storage and retrieval, the over- laying of various data sets to assist in targeting prospective areas, and as a drafting tool. The use of data-driven, predictive data analysis is the most recent effort in maximising the use of the extensive Misima database. By characterising the key controls and properties of the Umuna- type mineralisation, a Weights of Evidence, data-driven analysis produced a prospectivity map of Misima Island. The purpose of this map was to identify prospective areas yet to be explored and to assess the effectiveness of exploration to date.

Jan 1, 1997

By P. Bracher

Most efforts to mechanize low seam (narrow reef) mining of platinum ore are presently based on board-and-pillar methods with1.6?1.8 m in reef excavation. This paper attempts to substantiate the benefits of low profile mining: primarily improved head grade with resulting reduced tailings losses. Board-and-pillar equipment supplied by DBT, facilitating1.1?1.2m mining height has been in operation in an Anglo Platinum mine since September 2001. Major aspects of the equipment, battery scoops (LHDs) and rotary bolting rigs, are described and presently achieved results reported. The medium term industry goal is rock breaking without the use of explosives. An outline of present DBT developments is presented.

Jan 1, 2003

By C. Laird, C. E. Feltner

An investigation into the effect of a material's slip character on its high strain fatigue properties has been carried out using copper and Cu-7.5 wt pct A1 as representative wavy and planar slip mode materials, respectively. In copper, the constant term and exponent in the Coffin-Manson equation, ?EpNf1/2 = const, are unaffected by the temperature of testing or the history of the metal. On the other hand, in Cu-7.5 wl pcl Al, while the exponent is invariant, the constant is increased with respect to copper and increased further with decrease in temperature. The life in Cu-7.5 wt pct A1 is double that of copper at room temperature and about four times at 78°K. Fractoflaphic studies indicate that these diffevences in life are associated with the early stages of cracking. In copper, severe surface rumpling provides crack nuclei at pain boundaries independent of' testing temperature or the history of the metal. In Cu-7.5 wt pct Al, the planar slip mode of deformation prevents grain boundary folding; crack nucleation is therefore mainly transgranular and the increase in life with respect to copper is associated with a prolonged linking-up stage of such transgranulay cracks. At the lower temperature the increased difficulty of cross slip inhibits multiplication of trans-granular cracks and retards the linking-up process, giving a further enhaancement in life. It is expected that such behavior will be found general in materials of wavy and planar slip mode, respectively. STAGE II crack propagation in high strain fatigue takes place by a repetitive process of crack tip blunting in the tension part of a fatigue cycle followed by resharpening of the crack in the compression part.1-3 This mechanism has come to be called the "plastic relaxation process".3 At very high strains (lives to failure less than 103 cycles), most of the life of a specimen is spent in crack propagation by the plastic relaxation process.4,5 Since the differences in the cyclic strain hardening behavior of metals and alloys are comparatively small in this strain range,6,7 the amount of blunting at a crack tip depends primarily on the applied strain amplitude. The rate of crack propagation in this life range is therefore nearly constant with respect to material and temperature of testing. In the longer life portion of the high strain fatigue range (l03 to 103 cycles to failure), a considerable fraction of the lives is spent in crack initiation and Stage I growth. Grain boundaries have frequently4,5,8 been found to be the sites for this growth which is also associated with a surface folding process.4'5 Such folding behavior may also be general in any material having a grain structure and capable of plastic deformation. It has therefore been suggested475 that the universality of the Coff in-Manson law,9'10 constant,* where ?Ep is the plastic strain range and Nf the number of cycles to failure, is reflected in the approximate invariance of both the crack initiation and propagation behavior. It happens that, in most investigations of the phenomena associated with failure,4,5,8 materials with a wavy slip mode have been used as vehicles for the studies, or else "normally" planar slip mode materials have been tested under conditions giving rise to wavy glide deformation, e.g., stainless steels cycled at high temperature.'' The purpose of the present investigation was to determine whether or not different cracking phenomena would occur when the slip mode of a material is planar and if the associated life to failure would be different than that of a wavy slip

Jan 1, 1968

The epithermal Au-Ag deposits of the Hauraki Goldfield have formed in the convergent plate margin setting of the Coromandel Volcanic Zone (CVZ). The deposits form as siliceous lodes in the upper parts of geothermal systems associated with andesitic and rhyolitic volcanism. Two types of low sulphidation epithermal mineralisation are recognised in these volcanic terranes. Vein deposits within the rhyolitic terrane in the east and south of the CVZ (Whitianga Province) are typified by Chalcedonic Silica-Adularia-Illite type mineralisation. The veins are hosted by both rhyolite-dacite volcanic rocks and the underlying andesitic basement. The mineralisation formed by episodic violent decompressional boiling of deeply circulating meteoric water, with some magmatic fluid contribution; this boiling was associated with hydraulic fracturing and hydrothermal eruptions in geothermal systems where the piezometric surface of the deep geothermal reservoir lay near-surface. Such episodic boiling provides chalcedonic veining, banding and brecciation textures, adularia stability, bladed calcite, and extreme loss of H2S gas from the fluid to cause major gold deposition.   Crystalline Quartz-Illite-(Adularia-Kaolinite) type mineralisation is widespread in the andesitic terrane forming the northern and western portions of the CVZ (Kuaotunu Province). There is a spatial association with weak mineralisation of the high sulphidation (Vuggy Silica-Alunite-Kaolinite-Illite) epithermal type and porphyry eu-Au type. Crystalline Quartz mineralisation is probably formed by the mixing of shallow acidic groundwaters with the ascending deep geothermal fluid in geothermal systems beneath andesitic stratovolcanoes. The piezometric surface to the deep geothermal reservoir in these systems is likely to lie at considerable depth, with acidic gases rising from the geothermal reservoir condensing within the overlying vadose zone. The cooling effect, oxidation and pH decrease accompanying mixing apparently overcomes the dilution effect, and results in quartz deposition, illite (and locally kaolinite) alteration, and precipitation of gold. A high level of base-metal sulphide precipitation also enhances gold deposition. Violent boiling of the mixing fluids may occur at local structural dilation sites, producing high grade "bonanza" gold mineralisation.

Jan 1, 1991

By Naj Aziz

The shear behaviour of reinforced rock joints is investigated for the bolt-grout-rock interaction and for failure mechanism. The effectiveness of the bolt application under lateral and axial loading conditions within surrounding materials is investigated in different medium strength. Double shearing testing of bolts were studied in concrete blocks of 20, 40, 50 and 100 MPa strengths, subjected to different pretension loads of 0, 5, 10, 20, 50 and 80 KN respectively. The experimental study was complemented with three-dimensional numerical analysis. Parameters examined include: shear resistance, shear displacement, induced strains and stresses during bolt bending process and its ultimate failure across the sheared joint planes. The conclusions drawn from the study were; the level of bolt resistance to shearing was influenced by the bolt profile configuration, the strength of the rock or medium influenced the level of load generated on the bolt, and the increase in bolt pretension has contributed to the increased shearing load of the bolted medium.

Jan 1, 2007

As the surface reserves are being depleted, more and more stone operators are seeking underground mining options. Stability of underground openings is a major concern for the safety and productivity. This paper relates to a field study conducted at a large underground limestone mine in Central Pennsylvania. Identification of hazards leading to ground failures and assessment of roof fall risks are important in mitigating injuries. Field observations at this mine were integrated with Roof Fall Risk Index (RFRI) mapping software recently developed by West Virginia University. The system is designed to combine field study data related to geologic factors, mining-induced damages, roof profile, and ground water influx to generate RFRI maps. The mine has adopted a proactive ground control program consisting of comprehensive examination of drilling and bolting logs; precision surveying of roof and rib; accurate mapping of cutters, falls, and geologic structures; and installation of extensometers and microseismic monitoring systems. Investment of time and resources has eliminated fatalities and lost-time injuries due to ground fall. This paper presents the geologic settings, mining conditions, ground control issues along with risk management and control techniques adopted at the study mine.

Jan 1, 2009

The New Zealand Minerals Industry is small but growing. Over the next 10 years it will be facing stiff international competition for skills to support this growth, particularly from Australia who are forecasting that a further 70 000 people will be employed by 2015.   The value of commodities mined and quarried in NZ continues to increase; and the value of coal, metals and industrial minerals production reached $1.505 billion in 2006, an increase of 15 per cent on 2005. Production increases will continue à. Latest Crown Minerals statistics show that national prospecting and exploration expenditure rose to $29.9 million in the year ended March 31 2006 û an increase of 46 per cent from the $20.4 million spent in the March 2005 year. The equivalent 2001 year expenditure was only $2.48 million.   The industry already experiences difficulty in recruiting the people it needs with ongoing demand for skilled underground miners, trades people, and mining professionals. This discussion paper will outline the national context with regard to labour, skills and training. It will suggest options and provide an opportunity for conference participants to discuss the way forward.

Jan 1, 2007

By Brian Reid

"This paper studies the progress made by hydraulic shovel manufacturers over the last few years, particularly in the areas of productivity increase and operating cost reductions.Five years ago, it was widely considered that the unit production cost for a hydraulic shovel in a mining application was double that of a cable shovel in the same application. The hydraulic machine manufacturers have taken up this challenge, and modern improvements in design, coupled with changes in maintenance techniques, have narrowed the gap to the point where it is valid to ask the question ""will the cable shovel exist in ten years' time?"".Historical BackgroundThe history of the cable shovel goes back to the early 19th century and the industrial revolution. Early machines were steam-powered and ran on rails.The ""power shovel"" and the ""dragline"" were the only mechanical means of mass excavation until the early 1950s. Rail-mounted units gave way to crawlers, which increased flexibility considerably. Some shovels were redesigned as backhoes, and some became extremely large when designed as stripping shovels primarily used in North American coal mines.In the early 1950s growth in hydraulic technology spawned the introduction of the hydraulic excavator, which soon began to replace the smaller cable shovels and backhoes used in the construction industry. They were completely self-contained with either a gasoline or diesel engine and, being much lighter, were more readily transportable.As the excavators grew in size from its early models of 0.5 m3 or less, many of the cable shovel models were discontinued. This was not surprising for several reasons, but the most obvious is that both were often made by the same manufacturer."

Jan 1, 1988

During the latter part of 1937 consideration was given to the construction of a; local smelting plant for producing blister copper. Previously copper concentrates had been shipped to the United States of America. The proposition had the advantages of a saving in cost of realization, quicker financial return and reduced dependence on overseas shipping.The smelter was designed by the existing staff, who had difficulty in obtaining data on small plants, particularly on the reverberatory furnace. Construction was started in March, 1938, and the reverberatory was blown in on January 16th, 1939. One roaster had been operating for several weeks prior to this date.While results and operating technique on this new departure in small-scale smelting are barely beyond the experimental stage, it is felt that the experience gained to this time should be recorded to help fill the obvious gap in published information covering plants of this type.At present there are three copper smelters operating in Australia; the other two plants are equipped with blast furnaces.LOCATIONThe new smelter is situated in a position convenient to the concentrator and to the power plant. The site is traversed on two sides by a brick flue, from an old smelter plant, which connects with a 250-ft. stack. This stack and portion of the old flue are used in connection with the...

Jan 1, 1939

By H Zhou, T Honeyands, M Zhou

In iron ore sintering, packing the granules onto the sintering strand to form a porous bed with optimum permeability is a complex dynamic process. The packed bed voidage is the key factor determining the flame front speed and the final sinter productivity and quality. Previous studies have found that granules are soft quasi-particles with a typical structure of nuclei with an adhering fines layer. The deformation of the adhering layer greatly affects the bed voidage during packing, which is related to the strength of the adhering layer and the force exerted on the granules. In this study, tablets simulating the particle size distribution in the adhering layer of granules were made for four single ore blends. Both the tensile strength and shear strength properties of these tablets were investigated as a function of water content by the uniaxial compression test and direct shear test respectively. The results of compression tests show that the adhering layer becomes weaker and more compliant with the increase of moisture. The most porous ore has a more rigid adhering layer than the other three tested iron ores at any given moisture content. In direct shear tests, the internal friction angle of the adhering layer ranged from 31° to 37° and varied little with the moisture content or ore type. The cohesion constant is around 1 kPa and is quite small compared to the stress applied to the granules during packing. Combined with the results of granulation and packing experiments, the influence of the adhering fines layer deformation on the degree of voidage loss is specifically discussed.CITATION:Zhou, M, Zhou, H and Honeyands, T, 2017. Tensile strength and shear strength properties of the adhering layer of granules in iron ore sintering, in Proceedings Iron Ore 2017, pp 117–112 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Study on Oil Agglomeration Flotation for Deinking

Sep 13, 2010

By David L. Holt

The contribution of grain boundary shear to total elongation, CS/E&apos;, has been measured in an Al-Zn eu-tectoid alloy that was quenched from above the invariant temperature, then annealed at 250° C to a grain size of&apos; 1.8 p. At 250°C, ks/E&apos; is low at both high and low strain rates, but reaches a maximum, estimated as 60 pct at an intermediate rate of 5 X 10 per rnin. Rate sensitivity, as measured by the index m = a log a/a log E&apos;, follows the same trend, and furthermore the maximum values of m and -cur at approximately the same strain rate. This result, combined with the metallographic observation that boundary migration enhances boundary shearing, is interpreted as supporting a previous suggestion that the high rate sensitivity characterizing super-plasticity is the result of combined boundary shearing and migration. It is suggested that the latter event relieves stress concentrations at triple points, and smoothes boundaries so that stress is governed largely by a viscous boundary shear. GrAIN boundary shear has been considered in relation to superplasticity in several recent papers.&apos; The problem has been to explain the high strain rate sensitivity of flow stress, and the variation of rate sensitivity with strain rate (E&apos;) and grain size (L). The requirements for superplasticity, small L and high T, suggest the reasonableness of an approach to high rate sensitivity involving grain boundary shear. Further support came from experiments on the A1-Cu eutectic alloy,&apos; where it was found that strain rate sensitivity of cast material annealed to produce an equiaxed, micron-size grain is always low; taking as an index of rate sensitivity m = a log a/a log <, m < 0.3. However, m in hot-worked alloy of comparable grain size can be as high as 0.7. In the cast and annealed material, each phase is a single crystal, the only boundaries are interphase boundaries, and it is, consequently, geometrically impossible for boundary shear to contribute to deformation in any major way. Other observations (for hot-worked material) were a-L at constant (low) strain rates and indications that the rate of recrystallization was enhanced as strain rate increased. As a result of this work, it was proposed that high rate sensitivity arises from a deformation mode of boundary shear associated with boundary migration. Migration serves to relieve stress concentrations at triple points, and smoothes boundaries so that they assume properties of fluid films. On the other hand, the low rate sensitivity observed at high and low strain rates reflects deformation of bulk material. Measurement of the variation of grain boundary shear with strain rate and m have not yet been made. Such measurements are important, especially in view of a proposal, differing in detail from the above, that high m arises merely from a transition between a grain boundary shear mode of deformation at low rates to a transgranular mode at high rates.2&apos;4 In the present work, the contribution of boundary shear to total deformation is measured and in addition metallographic observations are made on surfaces of deformed specimens to look at the interaction between boundary shear and migration. The Al-Zn eutectoid alloy was chosen for its homogeneous, fine-grained structure, which is obtained readily without hot-working. It has also been the subject of a previous phenom-enologically directed study. EXPERIMENTAL Material. Compression specimens, cross section 4 by + in., length \ in., were machined from a sand-cast ingot of composition 77.5 wt pct Zn, 22.5 wt pct Al. (The melt was prepared from 99.9 pct Zn and 99.99 pct Al.) After homogenization at 375°C for 50 hr, the specimens were quenched in brine and removed before the heat evolution that accompanies de -composition of the high-temperature phase.5&apos;6 The resulting microstructure, see Fig. l(a), was too fine for grain boundary sliding to be easily studied; coarser structures were obtained by annealing for various times at 2 50°C. Annealing was terminated by a brine quench. Final average intercept lengths between all grain boundaries (both interphase and those lying in a phase), L, were: 0.5 p [annealed for 15 min, Fig. (a)], 0.8, 1.1, and 1.8 p [Fig. l(b)l. Testing Procedure. An Instron machine was used for most of the compressive deformation. Tests were of two types: those in which crosshead velocity was changed in steps to measure m as a function of strain rate15 and tests at constant velocity to a fixed (engineering) strain of -0.2 (20 pct). Stress reached a steady-state value (a) which was plotted, on a logarithmic scale, against log strain rate (E&apos;). An alternate and equivalent evaluation of m was to take the slope of the log o vs log 6 curve. Time at temperature before testing was 15 min. Strain rates covered by the Instron (4 x lo-&apos; to 4 x 10&apos; per min) were insufficient; at a higher rate of 5 x lo2 per min a gas-operated testing machine was used, the gas driving a piston to compress the specimen at a controlled velocity.&apos; To obtain points on the log a vs log E&apos; curve at low rates, specimens were compressed by a dead weight. strain rate was an average value computed by dividing strain at the end of test by loading time. In some tests strain was measured at fractions of the loading time; creep rate was found to be reasonably constant.

Jan 1, 1969

By Robert M. Funk, James E. Lawver

The development of a laboratory and pilot-scale high-tension electrostatic flowsheet for the production of iron-ore super concentrates having silica contents in the range of 0.1% is presented, A variety of hematite and magnetite ores were tested with this flowsheet, and the pertinent metallurgical data are given. The applications and limitations of this process are brought out in terms of both practical and theoretical considerations. There have been many new developments in the past few years that have required mineral beneficiation engineers to consider new techniques for iron-ore concentration. Developments in iron powder metallurgy, and particularly the making of sheet metal directly from high-purity iron-ore concentrates, and the concept of using metallized pellets as a substitute for scrap in electric-furnace steelmaking have created demands for what is commonly referred to as iron-ore superconcen-trates. In most cases, specifications for superconcentrates are that they contain less than 0.1% total gangue, with some applications requiring less than 0.05% gangue. To produce these concentrates, new and modified processes are being developed, and the three methods receiving attention as the primary concentrating methods are: 1) Magnetic separation in which dry rotor-type equipment is used for magnetite and the high-intensity magnets are used for hematite. 2) Amine flotation. 3) "High-tension" electrostatic separation (or, elec-trodynamic concentration). This paper examines the high-tension electrostatic process in terms of its limitations and abilities for the production of iron-ore superconcentrates. A technically effective and simple flowsheet was developed through laboratory and 5 and 100-ton pilot-plant studies for the production of concentrates containing from 0.02 to 0.20% SiO, with iron recoveries between 85 and 90%. The process is also shown to be economically feasible. Laboratory Test Program Separation Characteristics: The suitability of the electrostatic high-tension method for iron-ore supercon-centration stems from the fundamental mechanism governing the process, i.e., particles are separated on the basis of differences in electrical conductivities. This conductivity is a characteristic property of minerals, and if the difference between the conductivities of two min- erals is great enough, then their separation can be performed by a high-tension machine. As shown in Figs. 1 and 2, the critical factor is the time necessary for the particle charge density, which is established by a corona discharge field, to decay to a level such that the centrifugal force acting on the particle exceeds its electrostatic, or image, force. At this point, the particle can leave the rotor at some trajectory and fall into an appropriate product receptacle. This decay time is directly proportional to electrical conductivity, and the process variables, such as feed rate, rotor speed, electrode configuration, and rotor composition, are selected to optimize the ability of the separator to resolve different conductivities. Table 1 lists the measured conductivities for some of the iron and gangue minerals used in developing the flowsheet. These results were obtained by using the conductivity cell described by Lawver and Wright.&apos; The discharge curve of most minerals that lend themselves to super concentration by high-tension is so fast that the

Jan 1, 1971

By K. A. Lewandowski

Agglomeration techniques are widely used by industry to form fine particles into larger masses that are easier to handle and process. One area where agglomeration is potentially useful is in heap leaching operations. With-out agglomeration, fine particles travel through the heap, clogging the spaces between the larger particles and resulting in poor leach solution flow. Poor flow of leach solution will result in long leach rates and/or decreased metal recovery. Agglomeration immobilizes the fine particles and therefore improves heap permeability to fluid flow. Additional additives (binders) are needed to prevent agglomerates from breaking up as leaching solution percolates through the heap. Type II Portland cement and lime are two well-known binders used in gold and silver leaching, but these are limited to alkaline leaching environments. Various other products have been tested as binders, including polymers. This paper summarizes the benefits of agglomeration in heap leaching and the results obtained from the testing of several different agglomeration binders in heap leaching operations.

Jan 1, 2009

Differentiation of a basaltic (?) magma occurred in an active volcanic area during the late Miocene and Pliocene, and a change in the general mode of extrusion from fissure flow for the basalt to explosion for the andesite reflects an accompanying increasing magmatic viscosity. A caldera formed after the flow phase was completed and was filled with coarse agglomerate, much of which has a fused appearance. After an erosion interval its shape was modified and it became gradually deeper as repeated explosions from growing andesitic volcanoes caused large quantities of pyroclastic material to be deposited. At the close of this phase the floor abruptly collapsed when a, large block of the underlying crust was engulfed. The incompetent pyroclastics filling the caldera steepened in dip and the ensuing fractures were filled by the rising magma as dykes and sills and a chonolith formed below the caldera at a shallow depth. The ensuing activity reveals a further stage in differentiation and biotite is an important new ferromagnesian to be observed in the new rocks.Fracturing of the surrounding basalts was most intense in the rocks forming the periphery of the caldera where steeply and flatly dipping faults resulted from increasing horizontal pressure directed towards the caldera.Further differentiation resulted in the increased crystallization of orthoclase felspar, as evidenced by the numerous intrusives of trachy andesitic composition. Magmatic freezing caused mineralizers to accumulate at the top of the chonolith. These eventually escaped and auriferous pyrites, tellurides, quartz, and calcite were deposited in the surrounding rocks.The flatly dipping fractures are the most important and can be expected at various depths in a zone about 4,000 ft wide surrounding the caldera. Latest movement along these was controlled by magmatic consolidation rather than the shape of the caldera. Some flat faults were able to remain open during mineralization and acted as a feeder for the shallower fractures, thus limiting the depths to which the steeper dipping fractures were mineralized with the possible exception of one particular Nw.-striking lode (the Crown-Crescent).INTRODUCTIONThe gold deposits of the Tavua district were discovered in 1932 and from 1935 to June, 1961, 1,985,041 fine ounces of gold were produced from 4,202,504 tons of ore. Of the original three producers, only the Emperor remains active in the...

Jan 1, 1962

By M. Superfesky, P. Michael

Introduction The US Office of Surface Mining (OSM) is proposing changes to the Code of Federal Regulations in the interest of minimizing the adverse effects of excess-spoil-fill construction on the “prevailing hydrologic balance, fish, wildlife and other environmental values” (70 FR 35112). The proposed changes will require: (1) minimization the amount of excess spoil generated at a mine site; (2) minimization of the size of the fills constructed; (3) consideration of alternative configurations for disposal; and (4) development of a disposal plan that would minimize adverse impacts to the environment.1 To achieve those objectives, mining companies operating in steep-sloped Appalachia will likely build excess spoil fills (also called valley fills) that toe out at higher elevations in the hollows (i.e. to prevent or limit burial of streams). Consequently, the slopes of fill foundations will generally be steeper. Whereas the authors of this paper support these measures to protect the hydrologic balance and general environment, we wish to point out that placement of fills on steeper foundations can negatively impact the stability of the fills if proper care is not taken during their construction. It is important to note that in addition to impairing human safety, valley fill instability can negatively impact streams, the riparian habitat etc., and thus defeat the very purpose of the spoil minimization measures proposed. We do not, however, propose additional regulatory requirements pertaining to valley fill stability. Rather, we intend to emphasize the importance of engineering requirements already on the books, especially as they apply to the predominant type of valley fill constructed: the durable rock fill. We believe that the practice of restricting valley fills, to higher elevations in the watershed leaves less room for error in the design and construction of stable structures. This paper gives a quick review of the nature of excess spoil generation; methods and requirements of excess spoil fill construction, and the to-date stability record of the fills. The interest in excess spoil minimization and how it affects valley fill construction is also discussed. Most importantly, we will review long-standing issues pertaining to proper design and construction measures with respect to durable rock fills and discuss how they will become more critical as spoil minimization is practiced.

Jan 1, 2007

By C. Van der Veen

The use of the quasi static (Dutch) Cone Penetration Test (CPT) is described as a tool to predetermine the ultimate bearing capacity of the pile point. An analysis is given why a purely theoritical approach does not meet with success. A practical method is explained of extrapolating the cone resistance to predict the pile point resistance. The method has been calibrated against the result of 32 selected high standard loading tests on pile points in the Netherlands.

Jan 1, 1989

By Dale S. Preece, J Paul Tidman, Stephen H. Chung

"A discrete element computer program named DMC-BLAST (Distinct Motion code) has been under. development since 1987 for modeling rock blasting (Preece & Taylor, 1989). This program employsexplicit time integration and uses spherical or cylindrical elements that are represented as circles in2-D. DMC-BLAST calculations compare favorably with data from actual bench blasts (Preece et al,1993)."

Jan 1, 1997

By S J. Loach

Geological reconciliation is an indispensable part of BHP Billiton’s Western Australian Iron Ore (WAIO) operations. Since 2009 our reconciliations have been calculated in a single, centralised sequel-server database. This system draws data from across our operations and calculates a hierarchical sequence of reconciliation factors that span the company from the smallest grade control (GC) block to the whole of WAIO. It then presents the results using sophisticated graphical reporting tools.The initial motive for developing WAIO’s reconciliation system was to meet corporate compliance and public reporting requirements. The ability to validate our resource and reserve models by comparing their estimates of tonnes and grade with production figures remains the system’s principal function; however, as the system has matured, we have significantly developed its ability to support the improvement of various technical activities within the business. For example, the system can now calculate and report reconciliation factors for different resource classifications, short-term planning models and geometallurgical estimates.More recently, great emphasis has fallen on the system’s ability to detect and warn of possible geological issues that may pose a risk to either production schedules or product quality. We envisage a future where automated analysis of our large historical data set will enable high-risk conditions within future mine plans to be detected and highlighted.In all of these ways geological reconciliation plays an important role in contributing to this company’s financial and operational resilience.CITATION:Loach, S J, 2017. The development and future of BHP Billiton’s Western Australian iron ore geological reconciliation system, in Proceedings Iron Ore 2017, pp 415–422 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017