Search Documents

By William G. Pariseau

Few departments of mining, metallurgical or petroleum engineering in the United States have critical mass. Cost per student credit hour (SCH) in departments across the country are usually the highest among engineering departments, which are the highest on campus. Almost all departments are operating at fixed costs and enrollments could easily double without incurring much additional cost. However, the cost per SCH would remain unacceptably high and the probability of doubling enrollment is nil. Declining enrollment is a more likely future. The pressure to reduce SCH from university administration is unrelenting. And it has the potential for doing serious damage to program quality when standards and requirements are lowered in attempts to maintain enrollments and increase retention.

Jan 1, 2002

By J. M. Stuve

Standard heats of formation (AH°p) of YbCl3 (c) and TmCl3 (c) were measured by solution calorimetry. Heat of solution data are given for ytterbium and thulium metals and corresponding anhydrous trichlorides in 4.360 molal hydrochloric acid. The derived standard heats of formation of YbCl3 (c) and TmCl3 (c) were -229,370 ±720 and -235,820 ±400 cal/mole, respectively, at 298.15° K. The resulting heats of formation for YbC13 and TmCl3 are about 1 kcal and 6.3 kcal more negative than previously published values.

Jan 1, 1967

By Karl J. C. Harries

"4.1. INTRODUCTIONThis chapter, although divided into four parts, deals with only two principal topics. The first briefly describes and discusses some common types of property interests and considerations relating to them and the second deals with entering upon privately owned lands and obtaining the consent to do so.It should be noted that the terms “mining rights” and “mineral rights” are used interchangeably. As so used, they include the right to exploit the minerals and dispose of them for the benefit of the owner/lessee. This is relatively common in common law jurisdictions. In some jurisdictions, the two terms have distinct meanings, with “mining rights” referring to the right to work or exploit the minerals and “mineral rights” referring to the minerals themselves.Finally, it must be mentioned that the comments in the Introduction and §§ 4.2., 4.3. and 4.4. are based primarily upon Ontario law and Ontario’s mining and real property systems of registration. They have been included for illustrative purposes.4.2. LICENCES, CLAIMS, AND LEASESIn most jurisdictions, there are several basic types of interests that can be obtained from the state for mining purposes and that are of interest to the explorationist, as opposed to the operator. Different jurisdictions will have variations of these and possibly some extra ones that will address special purposes or local concerns. In virtually every jurisdiction, privately owned property rights are obtained through negotiation between owner and acquiror.Exploration or prospecting licence. This licence grants to the holder the right to prospect over a large tract of land and the exclusive right to acquire mining claims within that tract for the term of the licence. Such licences are usually negotiated documents requiring a minimum expenditure during the first year (often secured by a deposit or surety bond) and minimum annual expenditures thereafter to continue the licence in force up to its full term. The term will rarely exceed four years. The number of claims permitted to be staked will be limited in some way, possibly as to a maximum aggregate area or a maximum number of claims per annum. It is normal for the holder to have to drop part of the licensed area each year, so that the area shrinks annually, although exploration expenditure requirements will usually increase.These types of licences are usually used by governments to encourage exploration of otherwise unattractive or remote areas, such as the far northern parts of some of Canada’s provinces. They do not grant any real property interest in the area for which they are issued, and they will be subject to any claims or property rights that exist in the area. They are contracts with the state that grant certain exclusive rights in return for commitments to carry out work. They may or may not be specifically authorized by statute."

Jan 1, 2003

By John Rushton

Surface mining, from ore extraction to processing, requires many types of equipment to obtain the final product. Mine equipment often includes shovels, drills and haul trucks. Ore processing equipment, including plants, mills and concentrators, are also part of surface mining operations. Surface mining operations emphasize production. Production is where the bills are paid and fortunes are made. However, there must be support to keep the equipment operational. To most production people, equipment maintenance is a necessary evil. Maintenance is not glamorous work. It is often neglected when praise is being passed around. It is easy to recognize higher production, greater capacities, faster cycle times or more loads hauled. But who cares if an engine is replaced in 12 hours instead of 48? The answer is, everyone should - from the hourly miner to the mine manager. Surface mining equipment needs constant maintenance work. It must be lubricated, components replaced, electrical problems repaired and other problems addressed. Repair work for any surface equipment takes time away from production. It costs money. Maintenance costs cannot be avoided. However, they can be minimized. Minewide communication should include operations cooperating with maintenance. Traditionally, operations resist surrendering equipment to maintenance if it can continue to produce. The rationale is, every load that can be hauled today is money in the bank. If the unit is taken down, the money is lost. This thinking is prevalent in many surface mining areas, including the mill. "Not on my shift," the operator thinks. "Let the next crew worry about it. The problem with this thinking is in probability and statistics. The longer equipment goes without maintenance work, the higher the probability of equipment failure. When the failure does occur, it is certain to cause the equipment to remain down longer than if the maintenance department had been allowed to take it down. Many mining operations have closed early in their lives because of poor maintenance practices. This has become the industry standard because substandard levels of performance are acceptable. Management believes it gets five to six hours of work from maintenance people during an eight-hour shift. Actually, the industry average is less than two hours of work per shift. Real productivity levels of less than one hour are not unusual. There are few exceptions. However, a daily work schedule (DWS) will increase productivity at many properties by 50% to 100%. A 200% improvement is not unusual. The DWS will work. Maintenance people are among the most intelligent and motivated people on the property. They deserve the chance to be productive. [ ] In preparing a DWS, management needs to understand two productivity principles - the productivity spread and the real maintenance workday.

Jan 1, 1997

By W. H. Ode, W. A. Selvig

Briefly, this swelling test consists in heating 1 gram of pulverized coal in a silica crucible over a gas flame under prescribed conditions to form a coke button which is compared in size and shape with a series of standard profiles numbered 1 to 9. These profiles are intended to cover the size and shape of buttons obtained from coals covering a wide range in plastic properties. The number of the standard profile with which the maximum cross-sectional area of the button most nearly corresponds is recorded as the swelling index. Although the swelling test showed poor relationships with the various tests that were used for measuring expansion or contraction of coal during carbonization, it gave indications of having value in measuring free-swelling and coking properties of coals when burned on fuel tests. An opportunity to investigate this occurred when an engineering company reported pronounced differences in burning characteristics on grates of various shipments of Pocahontas coal. Some of these coals gave trouble by swelling excessively and clogging the grate. Samples were obtained, and it was found that the troublesome coals gave radically higher free-swelling numbers than did the coals that performed satisfactorily. Also, it was found that the free-swelling index test gave better differentiation between coals than could be obtained from the coke buttons from the standard volatile-matter test or iron agglutination-value results. The results of the free-swelling test were confirmed by the Subcommittee on Plasticity and Swelling, Coal, a special group of the Subcommittee, under the chairmanship of R.A. Shuman, worked along with the test method. Estberg, Limacher, and Shuman of the Battelle Memorial Institute investigated the various factors affecting the test and found that the swelling index was a good indication of the suitability of coal for performance on residential-type stokers from the swelling characteristics of the coal. Data were presented that also showed that the index was helpful in the selection of coal for industrial underfeed stokers.

Feb 1, 1948

The proper understanding of the functioning of ground support under dynamic loading and the current approaches to designing of dynamic support are plagued by a great deal of uncertainty and lack of knowledge. This applies equally to the understanding of the support capacity as well as the demand placed onto the support due to dynamic loading. This lack of understanding currently leads to a case of design indeterminacy. This paper does not aim to solve this problem of design indeterminacy but to explore some of the issues that need consideration to obtain a better understanding of the dynamic demand on ground support systems. Keywords ground support, dynamic loading.

Dec 1, 2013

By John A. Meech, Irene E. Cristoveanu

"The separation of hematite fines (100% - 38 um) from quartz fines (100% -75 um) was investigated using coarse hematite (-212 + 150 um) as a carrier in an oleic acid collector system. Oleic acid additions, per cent coarse additions, combined conditioning time and ferric chloride additions were examined.It was found that carrier flotation is a dominant mechanism for fine hematite recovery at oleic acid levels greater than 200 g/t and coarse additions of 10 per cent. Hetero-aggregation is favoured under conditions of lower levels of oleic acid in the presence of ferric chloride and at conditioning times greater than ten minutes.Ferric chloride acts as a depressant for pre-reagentized coarse hematite at oleic acid levels below 150 g/t. At concentration levels above 500 g/t, ferric chloride interferes significantly with the success of carrier flotation of fine hematite.The sensitivity of carrier flotation to changes in oleic acid addition, ratios of fine and coarse material, conditioning time and the presence of an inorganic electrolyte emphasizes that its application is only suitable when flotation conditions can be stabilized.IntroductionThe production of fine material is unavoidable during the comminution of iron ore . Due to the difficulty of recovering iron from this fine material by various gravity separation methods, flotation can often be a more attractive process producing high-grade material at high recovery. One variation of the flotation process, that can be useful for recovering ultra fine minerals (<10 um) , is known as carrier flotation. This process involves the utilizat ion of coarse particles ( > 150 p.m) which act as flocculation centres to which the fine hematite particles (10 - 40 u.m) become attached and are carried or "" piggy-backed"" into the froth phase."

Jan 1, 1985

By D. R. Parrish, W. E. Lamoreaux, W. W. Owens

Several methods are now being used by the industry for determining the gas-oil flow characteristics of reservoir rock samples. Most of the laboratory experirnerltal rlzethods can be classified either as steady-state, unsteady-state, or Hassler-type tests. Although the validity of the results obtained by any specific method is not questiorzed, in general, the complexity of these methods leaves much to be desired. This investigation dealt primarily with the development of a simplified unsteady-state (gas drive) laboratory test method for measuring kg/ko re1ationships of small core samples. A procedure for selecting uniform and representative sandstone rock samples was developetl since it was observed that the reliability of the test resu1ts was dependent upon having a sample which was uniform in porosity and permeability. The importance of factors known to influence the results of this type test, such as oil viscosity, gas expansion, and pressure differential were eva/uated. The method of calculating the test results was found to give valid data over a wide range of gas expansion. The limits of pressure differential and oil viscosity which would insure reliable results were defined. In cornparisorz with other presently used testing methods, the gar drive method requires considerably less apparatus, is less time consuming, and is more readily adaptable to a routine type core test. INTRODUCTION The detcrmination of the gas-oil flow characteristics of reservoir rocks has been given concentrated study by the oil industry for the past decade. Both analytical and experimental methods have been considered. The analytical methods have generally relied on a simplified characterization of porous materials in order that the fundamental laws of fluid flow and capillarity could be utilized. More direct experimental methods have been proposed by numerous production research laboratories with the primary goal being a simple and inexpensive, yet reliable method for measuring the gas-oil flow characteristics of reservoir rock samples. The experimental methods which have been reported in the literature generally can be grouped into one of the following classifications: 1. Steady state1,2,3,4 in which a fixed ratio of flowing fluids is forced through the test sample until equilibrium conditions of saturation and pressure gradient are established. 2. Hassler or stationary liquid method5,6,7 in which a uniform liquid saturation is attained, usually through capillary desaturation, then gas or oil is flowed through the sample at a pressure drop insufficient to disturb the pre-established saturation. :. Non-steady state method1,8,9,10 In which only the gas phase is injected into the sample, causing displacement of the oil phase and resulting in a system of continually changing average saturation and saturation gradient. The steady-state and Hassler methods have been most popular because, no doubt, of the simplicity of the actual relative permeability calculations. The problems involved in these methods were limited to apparatus design and measurement techniques. In the steady-state method, for instance, a constant flowing fluid ratio is established which, at equilibrium, results in an essentially uniform saturation over the entire length of the test sample. Therefore, the basic flow characteristics could be obtained by correlating the average saturation of the test sample with the kg/ko determined at various flowing gas-oil ratios.

Jan 1, 1957

By Peter Cali

There is one organization in Sweden, The Swedish Deep Stabilization Research Centre, which has been working with these questions and there is also a project, Eurosoilstab, within European Union to take a manual for deep stabilization.

Feb 10, 2003

By Víctor Cabrera

El objetivo de la ingeniería y construcción es preparar productos comerciales, tales como metales y concentrados, en base de la explotación minera para su posterior despacho y embarque al mercado comprador. Es decir, el proyecto minero es el puente entre la explotación minera y el mercado. En ese sentido, el presente texto señala las claves para la ejecución de un proyecto minero que va desde un inicio hasta su desarrollo. Así también debe cumplirse las metas del propuesto, calidad técnica y programación del proyecto.

Aug 25, 2002

By Binbin Luo, Northeastern University, Chuanyao Sun, Jie Liu, Yimin Zhu, Yanjun Li

"A series of new type collectors a-bromo-saturated fatty acids, CH3(CH2)5CHBrCOOH (a-BHA), CH3(CH2)7CHBrCOOH (a-BDA), CH3(CH2)9CHBrCOOH (a-BLA), CH3(CH2)11CHBrCOOH (a-BMA) were synthesized from saturated fatty acids and bromine by solvent-free method (Hell-Volhard-Zelinski reaction) in laboratory. The micro-flotation tests of quartz mineral were conducted at a relatively low temperature of 15 °C. The adsorption mechanism of such collectors on quartz mineral surface were established by zeta potential measurements, in conjunction with the results of quartz micro-flotation tests. The flotation results showed that the collecting ability is in the order of a-BMA > a-BLA > a-BDA > a-BHA for the flotation of quartz mineral, which also demonstrating that the a-bromo-saturated fatty acids (a-BFAs) are new selective collectors for reverse flotation to remove quartz mineral from iron ores at a relatively low temperature.INTRODUCTIONThe requirement of higher pulp temperature to maintain the activity of fatty acid anionic collectors which have been widely applied in technological process of iron ores reverse flotation lead to a great deal of energy consumption.The purpose of this paper is to synthesize a new modified collector with carbon chains from eight to fourteen atoms, with strong electronegativity bromine atom introduced into a-carbon position to improve the activity and solubility of the reagent so that it can be adopted at a comparatively low pulp temperature. The collecting performances of these new collectors on quartz surface were studied, and the structure - properties were discussed in light of zeta potential measurements and quantum chemistry calculations."

Jan 1, 2016

By A. P. Massmann

Design for economical operation, minimum operating labor and minimum maintenance for labor and supplies are virtually inseparable. Each consideration has a vital bearing on the other. Let us assume that we have the design complete for the most economical operation with a minimum of operating personnel. This means, in addition, that we have the fewest number of operating units consistent with the product requirements for a team or metallurgical coal which we are called on to produce. The number of units will vary greatly, being influenced by design, washability characteristics, tonnage and degree of quality control necessary by reason of producing a product for metallurgical, steam or domestic use. The units involved most ordinarily for any type coal preparation plant will number as a minimum the following: 1. Hoppering R.O.M. Coal 2. Feeding

Jan 1, 1959

By Ling Yang, John Henderson

Self-diffusion coefficients of copper in molten copper have been measured by the capillary reservoir method in the temperature range 1140o to 1260°C. The results can be represented by the equation D = [(1.46 * 0.01) x 10-3) exp [(-9710 * 710)/RT] cm2/sec. The energy of activation agrees within the limit of experimental uncertainty with that for viscous flow. The relationship between the diffusivity and coefficient of viscosity is best described by the equation D = kT/4pnr cm2/sec. MEASUREMENT was made of the self-diffusion coefficient of copper in molten copper in the temperature range 1413º to 1533ºK, using the capillary reservoir technique and CU64 as the radioactive tracer.The procedures for filling the capillaries, making the diffusion run and evaluating Dcu from the counting results were the same as described previously.1,2 All experimental operations involving the melt were carried out in a purified argon atmosphere. A graphite crucible, enclosed in a McDanel tube, was used as a container for the melt because of its satisfactory nature as a refractory material and the low solubility of carbon in copper. Graphite was also used for the capillary material. A McDanel thermocouple sheath, to which graphite radiation shields were affixed, was used to hold the capillaries. By moving this sheath through a rubber seal at the top of the McDanel tube, the capillaries could be lowered into or raised out of the melt. A Globar furnace with a constant temperature zone (± 2°C) of 2 in. was used to heat the assembly. The temperature of the furnace was the equilibrium value corresponding to a given setting of the transformer. Temperature was measured with a Pt-10 pct Rh/Pt thermocouple and varied during a run

Jan 1, 1962

By R. K. Zipf

A method is presented for creating realistic numerical models for practical coal mine ground control. The method includes procedures to collect the necessary mechanical input parameters from a geologic core log, procedures to set up a model and procedures to interpret calculation results. The input parameters come from a detailed geologic core log and extensive point load tests of estimate rock layer strength. A suite of material property input parameters is proposed which allow the user to go from core log to numerical model inputs. Rock bolt anchorage properties are also linked to the material properties of each geologic layer in the model. Following this procedure leads to very realistic calculations of the rock failure process and rock support system behavior. These calculations in turn enable realistic comparison of the effectiveness of alternative rock support systems.

By Alessandro Martins Duarte

O forno elétrico a arco é dos equipamentos mais versátil para produção de aço e representa os principais processos para reciclagem de sucata. A Aperam South America Timóteo possui dois fornos elétricos, dedicados à produção dos aços inoxidáveis, onde praticamente 90% da sucata de inoxidáveis gerada na planta é reciclada neste processo, com o adicional de sucata adquirida no mercado de inoxidáveis. Este projeto teve como objetivo o incremento de produtividade nos fornos elétricos através de ajustes no programa de potência dos fornos na fase de fusão, objetivando a redução do tempo de forno ligado, redução de paradas por engaiolamentos de forno, redução do consumo de energia elétrica e eletrodos. O incremento de produtividade nos fornos elétricos permitiu uma maior produção de aços inoxidáveis da série austenítica, ofertando um volume maior de aços para os processos posteriores de refino no AODL. Para a modificação do programa de potência foram necessárias adequações no processo de confecção de carga e ajustes no modelo térmico do forno, baseados na temperatura final da carga, estimada para cada fase. Além dos ganhos de produtividades auferidos com o projeto, o mesmo proporcionou uma economia significativa no consumo de energia elétrica e eletrodos, próxima a kR$ 3700 por ano.

Oct 30, 2017

By S. Belair, V. Weigel

As a growing mining company, ERAMET is looking for new positions on the strategic metals market. In this context, the Gabonese Maboumine pyrochlore deposit is currently being studied for the recovery of niobium, tantalum, rare earth elements (REE), and uranium. This ore shows mineralogical and chemical characteristics that make it challenging to process by already known practices, from both technical and economic points of view. In this context, ERAMET has developed since 2008 an innovative hydrometallurgical process which has been successfully operated at a pilot plant scale. While the upstream part of the process aims to dissolve the valuable elements in sulphuric acid, the downstream part of the process aims to recover them separately in a marketable form. The focus here will be on the recovery of the REE. The ore deposit contains approximately 1.4% of REE including 87% of light REE and 13% of medium-heavy REE. The challenge in this process lies in the fact that the major elements in the matrix are iron and aluminum. An innovative process has been developed in order to recover all of the REE in these unfavourable conditions, described in this paper.

Jan 1, 2014

CONTENTS PAGE East Texas, except the Gulf Coast-H. Vance 3 Gulf Coast-L. P. Teas 8 Texas Panhandle-C. C. Rae 16 North Central Texas-H. F. Smiley 23 North Louisiana, South Arkansas and Mississippi-B. C. Craft 25 Oklahoma-C. H. Pishny, Raymond M. Carr and E. J. Dickinson 31 Kansas-E. A. Koester 35 Rocky Mountain District-C. D. Johnson 46 Illinois and Indiana-T. Wasson 49 Michigan-T. Wasson 52 Eastern States-P. D. Torrey and W. H. Young, Jr 58 West Texas and New Mexico-W. V. Vietti. Published as a Supplement.

Jan 1, 1933

By V. I. Lakshmanan, Dan A. Mackie

Traditional vat leaching methods have had limited success, primarily due to the high cost of loading and unloading the vats. In general, such batch methods are labor-intensive and costly. Heap leaching has emerged as a viable, low- cost alternative, but low recoveries, normally in the 70% range, offer opportunities for improvement. Also increased regulatory guidlelines for effluent and spent heap leach pads disposal offer potential for alternative methods. The Mackie Vat Leaching Jig (MVLJ) has had its incubation at Ortech International, where bench scale through pilot scale testing continues. Design developments and testwork over the past two years indicate that the time may be right for field trials.

Jan 1, 1990

By C Tickell

Achieving occupational health and environmental noise objectives is a major consideration in the planning or operational phase of resource development and industrial projects to meet the needs of the workforce and community and comply with legislative requirements. For material handling systems, ventilation plants, mobile equipment, process plants and fixed infrastructure, noise emissions need to be considered at the design phase. The preferred approach is to provide noise emission technical specifications, but in many cases this is not stipulated. An occupational noise requirement, such as ‘not to exceed 85 dBA at 1 m’, is often provided, but this will not achieve the required occupational or environmental noise objectives and may cause overly stringent requirements when they may not be needed. It should be noted that when developing the technical specification, measuring compliance needs to be taken into account as, in some cases, measuring may be very difficult or even not possible.This paper will discuss the requirements for providing an effective noise specification that ensures the environmental and occupational noise objectives are able to be achieved and that, once installed, compliance can be measured. It discusses planning such as when to set the objective, correlating the appropriate objectives for the environmental and occupational noise requirements, allowing for measurement tolerance, providing a suitable criteria and data format for the suppliers to respond to and methodology to measure compliance. Different phases of a project require different approaches to planning for noise management and these will be discussed in the paper. Examples from 35 years of industry experience will be included.CITATION:Tickell, C, 2016. Preparing effective specifications for occupational health and environmental noise objectives in mining project design and delivery, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 781–788 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J. W. Griffith

"The mines in the Bancroft area of southeastern Ontario, a few kilometres west of the town of Bancroft, are in Faraday and Cardiff Townships. Three companies, known as Canadian Dyno Mines Limited, Macassa Gold Mines Limited (Bicroft Division) and Madawaska Mines Limited (formerly Faraday Uranium Mines Limited), with plants capable of handling a total of 4,()()() tons (3,629 tonnes) of ore a day, were at one time in production. A fourth company, Greyhawk Uranium Mines Limited, operated a small mine whose ore was shipped for custom treatment to the nearby Faraday mill. Canadian Dyno Mines Limited ceased operations in June 1960. In June 1963 the Bicroft Mine was closed and a year later Faraday closed because of contract completion. But in 1975, Faraday (now called Madawaska) was re-opened but closed again in 1982. During 1959, the peak year, these four mines produced an estimated 1,100 tons (998 tonnes) of uranium precipitates, which represented nearly 7 per cent of Canada's output for that year(Fig. 1).The deposits occur in pegmatitic granite dykes in a region of high-grade metamorphic and metasomatic rocks. Uranium distribution is usually controlled by the distribution of mafic minerals, particularly hematite and magnetite, and by late fractures. The best visual indicators for uranium concentration are hematite staining in the pegmatite, followed by the amount of mafic inclusions or crystals. The Bancroft area orebodies are the only known deposits of the general pegmatitic class in Canada that contained economic deposits of uranium. The principal radioactive minerals are uraninite and uranothorite. By comparison with many other pegmatitic occurrences, some of the ore bodies are unusually large, persistent in depth and relatively rich in uranium minerals. At the end of 1981, total ore reserves were estimated at 1,500,00 short tons (1,360, 000 tonnes) averaging 0.11 % U3O8."

Jan 1, 1986