Search Documents

By Christopher M. St. John, Tony F. Zahrah

Empirical and numerical methods are the two extremes of the tools available for the seismic design of subsurface excavations and underground structures. Both have their limitations: when relying on purely empirical methods directly relevant experience may be scant; site data may be insufficient to justify a comprehensive dynamic analysis. The primary purpose of this paper is to review the analytical tools available to the design engineer of subsurface excavations and underground structures. Particular attention is devoted to simplifed models that appear to be applicable in many practical cases.

Jan 1, 1985

By L. A. Updegraff

Before discussing the application of capacitance for the measurement of moisture content in a moving stream of coal it might be well to first give a brief description of the process and then show how it can be applied to the coal industry. A capacitor may be described as a device having two conductors separated by an insulator, the conductors hereafter being designated as a test cell or test plates and the insulator as the dielectric. Capacitance, therefore, is a measure of the ability of a capacitor to store an electrical charge. Two basic factors that affect capacitance are the dimensions of the capacitor and the dielectric constant of the insulator. Capacitor dimensions which affect its capacity are the area A of the conductive surface, and the distance d between plates. Capacitance is inversely proportional to the distance between plates and directly proportional to area A, so if capacitance is indicated as C and the dielectric constant as K the equation for capacitance would be C = AK/d. The dielectric constant can be described as the ratio of the actual capacitance of any given material to that of a vacuum, which is unity. In industrial applications the area of the plates remains constant as also does the distance between them, leaving the dielectric constant as the only variable to affect the capacitance measurement. Figure 1 is a schematic diagram of an r-f excited capacitance bridge in which a test cell is part of the circuit. This bridge consists of four capacitors in two pairs connected across an a-c voltage source. In one side of the circuit the two capacitors are fixed but in the other side they are variable, one being the rebalance capacitor operated by the servo motor and the other the test plates between which the dielectric passes. Capacity of the plates is a function of the dielectric constant of the material between them and is measured at radio frequency. Within the recording instrument is an r-f oscillator and a 60 c ps modulator. The radio frequency signal is generated by the oscillator, modulated by a 60 cps wave, and sent to the bridge. Therefore the signal entering the capacitive bridge is a radio frequency carrier with a 60 cycle envelope, If the bridge is in balance as the signal enters there would be no voltage drop and so no output by the detector. As long as the dielectric constant remains the same the bridge will stay in balance. However, any change in the dielectric constant, which in this case would be a change in moisture content, would affect the bridge. Higher moisture increases the capacity of the test cell which causes less voltage to develop across it causing imbalance of the bridge. This in turn causes a radio frequency signal to appear at the detector. Output from the detector is a 60 cycle ripple which is in proportion to the imbalance of the circuit. A 60 cycle amplifier boosts the detector signal to enough power to drive the servo motor which positions the recording pen and also rotates the variable capacitor, to which it is mechanically connected, to bring the bridge back in balance. An increase in moisture causes the servo motor to rotate in one direction, but a decrease causes imbalance in the opposite direction, and thus rotates the motor in that direction. This brings the bridge back in balance and stops the motor. The bridge shown in Figure 1 has been modified so as to provide a wide range of adjustments. Coarse and fine span adjustments located in the recording instrument are set to govern the amount of pen movement for a given change in capacitance. A measuring head unit contains coarse and fine zero adjustments for

Jan 1, 1961

BP Minerals America (BPMA) has completed its $400 million modernization of Kennecott Utah Copper's Bingham Canyon mine. Modernized facilities include the in-pit crusher, conveyor, ore storage area, concentrator, ore pipe-line, and tailings pipeline. With modernization, Kennecott will achieve substantial cost reductions. Bingham Canyon is now one of the lowest cost copper producers in the world. And the mine will continue to provide jobs and income in Utah for another 30 years or more. The Modernization Project began in February 1986. The work took 33 months. In late 1987, the construction force peaked at 1100 workers. Kennecott Utah Copper now employs a permanent work force of 2100 employees. Less equipment and more efficiency The modernization work has increased the scale of the facilities that transport and process copper ore. A large, continuous transport system has replaced multiple haulage units. Fewer but larger pieces of equipment have replaced many crushing, grinding, and flotation units. The result is less maintenance, fewer employees, and improved metal recoveries. About one-third of the $400 million modernization project is directed at improving ore movement by eliminating rail transport. The new concentrator accounts for the remaining two-thirds of the modernization investment. The modernized plant was started up in stages. In February, ore was fed to the crusher. By the end of March, the three grinding lines were operating and the flotation circuit was producing copper concentrate. In July, the design through-put rate of 70 kt/d (77,000 stpd) was reached. October saw the achievement of targeted metal recoveries that corresponded to the fully modernized operation. It is estimated that Bingham Canyon will annually produce 181 kt (200,000 st) of refined copper, 9.3 t (300,000 oz) of gold, 71 t (2.3 million oz) of silver, and 5.4 kt (12 million lb) of molybdenite. Current Bingham Canyon production is about 97 kt/d (107,000 stpd) and a similar amount of overburden. Some 70 kt/d (77,000 stpd) of ore are processed through the in-pit crusher and 27 kt/d (30,000 stpd) of ore are transported by rail. The Bingham Canyon mine has yielded more than 11 Mt (12 million st) of refined copper. In 1863, precious metals - silver-bearing lead - were first discovered in Bingham Canyon. What was once a mountain is now a huge open pit. In fact, the mine is the world's largest man made excavation. The pit is some 4 km (2.5 miles) wide and 0.8 km (0.5 miles) deep. Since the pit began operating in 1906, more than 4.5 Gt (5 billion st) of material have been removed. Modernized facilities Electric 21 m3 (27 cu yd) or 23 m3 (30 cu yd) shovels are used to load the haulage trucks. Both 154 t (170 st) and 181 t (200 st) trucks are used to haul the ore to a mobile, in-pit crusher. The crusher replaces three crushers located at the old concentrators. There are two dumping locations at the new crusher, which can handle two trucks a minute. The 1.5 x 2.7 m (60 x 109 in.), 745 kW (1000 hp) Allis-Chalmers gyratory crusher reduces the ore to 254 mm (10 in.) size or less and delivers it to the conveyor. The crusher and conveyor systems are capable of handling 9 kt/h (10,000 stph) of ore.

Jan 11, 1988

By N van Aarde, B A. Moore, S van der Merwe

Frequently materials handling operations are compromised by transfer chute problems ranging from high wear rates, blockages and ineffective loading of the downstream conveyor. This paper will present the design flow implemented to overcome problems in two case studies utilising discrete element modelling incorporating material characterisation.Material testing is relevant in achieving a valid discrete element method (DEM) simulation model and subsequently a valuable design tool for transfer chute assessment and design. It is well recognised that in the current growth and demand for mineral resources, leading to ever increasing conveyor capacities associated with export terminals and mineral processing facilities that transfer chutes are a key focus point. The successful performance of the transfer chute is also dependent on operating with a ærobust rangeÆ of material flowability and handling characteristics. This requirement is crucial in accommodating mineral ores from developing resources, which are often more friable and stickier than in past decades.This paper will include details of chute installations associated with iron ore and coking coal, from the DEM simulations through to the performance of the installed and commissioned plant.CITATION:Moore, B A, van der Merwe, S and van Aarde, N, 2013. Implementation of advanced transfer chute designs, in Proceedings Iron Ore 2013 , pp 445-450 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

THE 125th meeting of the Institute was held in New York, Feb. 20-23, 1922, inclusive, and was the most successful annual meeting of the Institute ever held; there was a larger registration, there were more sessions of importance, and a greater number of sessions, than in any previous year. The total registration was 1331, comprising 351 New York members, 393 visiting members and 587 guests. At the annual business meeting of the Institute, held on Tuesday, Feb. 21, with President Ludlow presiding, there was a much larger attendance than usual. The report of the tellers was read and the following officers were declared elected: Arthur S. Dwight, Director and President-District 0 J. V. W. Reynders, Director and Vice-president-District 0 A. R. Ledoux, Director and Vice-president-District 0 Charles F. Rand. Director-District 0 George D. Barron, Director-District 0 William H. Bassett, Director-District 1 Thomas B. Stearns, Director-District 8 William Kelly, Director-District 5

Jan 3, 1922

By Y Xie, D Willingham

Predictive maintenance (also known as ‘condition/health monitoring’) refers to the intelligent monitoring of equipment to avoid future failures. In contrast to conventional preventive maintenance, the maintenance schedule is not determined by a prescribed timeline; instead, it is determined by analytic algorithms, such as machine learning, using data collected from equipment sensors and/or via simulation.Predictive maintenance offers the following benefits for operators and equipment manufacturers:- reduces equipment downtime by identifying issues before failure, thereby enabling convenient scheduling of equipment service and extending equipment lifetime- determines the root cause of the failure, enabling appropriate service to be performed without utilising resources to determine a diagnosis- avoids the unnecessary costs of maintenance and unexpected failures- improves safety and product quality.Algorithms and data are critical to predictive maintenance success. Sensor data is first preprocessed using advanced statistical and signal processing techniques; it is then combined with predictive modelling techniques, such as machine learning, to estimate equipment health.Once tested, predictive maintenance algorithms may be used in an operational setting within an IT environment, such as a server or cloud. Alternatively, algorithms may be implemented in an embedded system directly on the equipment, allowing for faster response times and significantly reducing the amount of data sent over the network.CITATION:Willingham, D and Xie, Y, 2017. Predictive maintenance modelling for bearing-based equipment, in Proceedings Iron Ore 2017, pp 627–630 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By C Vuillier, A Roshdieh

Water is the main medium for removing impurities from iron ore during wet processing to achieve a higher quality product. However, there is a substantial increase in freshwater consumption due to an increase in demand from the following two factors: in the past 55 years the world population has doubled from 3 to 7.5 billion and crude steel production has increased five times from approximately 350 to 1662 Mt/a (IISI, 2008). Furthermore, social development in developing countries exacerbates water consumption making freshwater an increasingly valuable resource with an average distribution of 70 per cent for agriculture, 20 per cent for industry and only ten per cent for domestic consumption (Hourtolle, 2005; OECD, 2009). Rapidly changing regulations over the access and preservation of water across the world indicates the growing importance of this issue, so the mining industry must adapt to this continual change and must be committed to increasing the efficiency of water usage.Tailings dams receive most of the water used by the process plant. In arid regions where evaporation is high and availability of water low or non-existent, technical solutions other than the conventional tailings dam, such as thickened and/or filtered tailings, exist to optimise the recovery of water and reduce the need for external water consumption. However, these solutions present additional challenges, such as energy consumption and transportation from the process plant to the ultimate storage area.This paper considers a range of alternatives covering thickening and filtering, transportation and storage, water return, closure and rehabilitation. Mining projects in the future will be more affected by the rising cost in water and tighter regulations in accessing water and energy. Good tailings management can contribute significantly to reducing the dependence on these two key commodities (water and electricity), improving the resilience of iron ore projects especially in arid regions and areas with high competition for water.CITATION:Vuillier, C and A Roshdieh, A, 2017. Minimising the water loss associated with mine tailings disposal, in Proceedings Iron Ore 2017, pp 245–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By O N. Antzutkin, W Forsling, K J. Pike an

The adsorption mechanism of three different O,OÆ-di-alkyl-dithiophosphate (dtp) collectors, K[S2P(OR)2] with R = Et, i-Bu and i-Amyl, on the surface of synthetic chalcocite (Cu2S) was studied by means of solid-state 31P CP/MAS NMR spectroscopy. The morphology changes on the conditioned Cu2S surfaces, in the collector concentration range 0.1 - 10 mM, were also monitored with scanning electron microscope (SEM). In order to assign Cu(I)-dtp species on the surface of Cu2S, the corresponding bulk Cu(I)-dtp compounds, which are clusters of the monovalent copper containing either Cu6(antiprismatic) or Cu8(cubic) cores, were synthesised, and characterised by means of solid-state 31P CP/MAS and static 65Cu NMR. Further investigations on the crystal habits of the bulk systems were carried out by powder x-ray diffraction and SEM. A comparative analysis of the 31P chemical shift and chemical shift anisotropy (CSA) data estimated from the experimental NMR spectra of the polycrystalline bulk Cu(I) dialkyldithiophosphate complexes was used for assigning the 31P resonance lines in the NMR spectra of the collector treated Cu2S powder samples. The species formed on the synthetic Cu2S surfaces were assigned to polycrystalline phases of: Cu6L6 with L = Et2dtpû, Cu6L6 and Cu8L6(S) with L = i-Bu2dtpû, and Cu8L6(S) with L = i-Amyl2dtpû. A heterophase autocatalytic step process of both formation and growth of solid CuxLy (L = R2dtp, x = 6 or 8 and y = 6) complexes on the collector treated Cu2S surface is proposed. A possible role of the oxidised form of dithiophosphate collectors, bis[di-alkyl-thiophosphoryl]-disulfane (disulfide), is discussed in terms of a specific self-redox reaction. The second order quadrupolar lineshapes in 65Cu NMR spectra were simulated and the interaction parameters, CQ and hQ, for the bulk dialkyldithiophosphato-copper(I) complexes were obtained.

Jan 1, 2005

By H. Walqui

This paper describes operating gains resulting from standardizing operating and maintenance practices to improve the performance of the pebble crushing circuit at he Empire Concentrator. Past efforts have led to improved operating time but no additional throughput gains. New Operating standards and checklists were developed and introduced. The content and frequency of the review process indicators was then changed to take advantage of the new practices resulting in an increased feed rate and availability through the pebble crushing circuit.

Feb 27, 2013

By M. Martins

This work presents and discusses the influence of the surface tension (gLV) of methanol/water mixtures on the flotation response of apatite versus gangue minerals conditioned with flotation reagents (75 g/t cornstarch and 100 g/t Berol 867) at pH 10.6. Berol 867 is a collector composed of sodium alkyl sarcosinate plus nonionic surfactant. The highest Schulz efficiency of separation (recovery of apatite minus recovery of gangue) was achieved at ?51.0 mN/m. The critical surface tension of wettability (gC) of apatite was found to occur at 34.7 mN/m when determined by means of gamma flotation experiments, and it was 33.9 mN/m when determined by Zisman?s approach.

Jan 1, 2009

By M. R. Tek, L. K. Thomas, D. L. Katz

Threshold displacement pressures are needed to determine how much overpressure can be used in storing natural gas. An experimental technique for determining threshold pressures by displacing water with gas from samples saturated with water is presented. Threshold pressures for eight low permeability samples were measured. Threshold pressure data obtained in this work, plus data on higher permeability samples reported in the literature, are correlated with porosity, permeability, surface tension and formation resistivity factor. Mercury injection pressures also were measured and correlated with air-water threshold pressures. Threshold pressures were found to be independent of time. An aerial photograph of gas emerging from the top of a core shortly alter its threshold pressure has been exceeded shows that the gas bubbles are uniformly distributed across the face of the core. Channeling will occur, however, when an increased gas phase permeability is reached, A porous medium can be re resealed alter its threshold pressure has been reached, provided it has not been desaturated below a fixed saturation. Its new threshold pressure will be lower than when the sample is 100 percent saturated with water. INTRODUCTION The degree of overpressure in excess of the discovery pressure that a gas storage reservoir can withstand is determined by the ability of its caprock to contain gas, providing the pressure does not exceed the structural limit of the reservoir. The retention of gas in a reservoir by a caprock saturated with water is a result of the capillary forces acting at the gas water interface. Without the presence of water in a caprock, gas would leak out of the reservoir at a rate determined by the permeability of the caprock to gas. The ability of a caprock to contain gas is expressed in terms of its threshold displacement pressure, which is defined as the minimum pressure needed to initiate the displacement of a wetting phase by a nonwetting phase from a porous medium 100 percent saturated with the wetting phase. The gas industry must be able to predict how much "overpressure" a gas reservoir can withstand before leakage occurs by gas displacing water from caprock overlying the reservoir. This is of economic importance since the storage capacity of a gas reservoir is proportional to its pressure. The discovery pressure for most reservoirs is found between the upper and lower limits1 shown in Fig. 1. Discovery pressures in excess of their hydraulic pressure gradient are attributed to the compaction of an isolated shale formation by the overburden.2.3 The lower limit of 0.433 psi/ft corresponds to the weight of the overburden, the gradient of the rock itself. Somewhere between

Jan 1, 1969

By W. T. Swensen

The Anaconda Company, through its wholly owned subsidiary The Anaconda Company (Canada) I,td., has investigated, optioned and partially developed a large tonnage of iron ore amenable to magnetic concentration. The reserves are located in north central Ontario and occur within a twenty-two mile belt of layered and intricately folded metamorphic rocks, close to the north contact of an igneous complex of granite and pegmatite. There are two main ore deposits. Briarcliffe is a steep to vertically dipping body 100 to 500 feet wide and over a mile long. The Two Mile Lake deposit is flat dipping and confined to an open, asymmetrical syncline; it is approximately a mile wide and 250 to 4.00 feet thick. On its flat easterly plunge, it is saucer-like in shape and is amenable to open-pitting for an east-west distance of several thousand feet. Magnetometer surveys, confirmed by drilling, indicate at least a three mile eastward extension of this deposit. Location and Access: The property is located in the Kowkash Mining District of northwestern Ontario, roughly forty-four miles north of the community of Nakina on the main line of the Canadian National Railroad. (Fig. 1) Access during the exploration period was entirely by airplane from Nakina. (Fig. 2) More recently, Nakina itself was connected to the highway network in the Longlac-Geraldton area. The property is roughly 190 miles by existing and proposed railroad from the Great Lakes waterway system. The Trans-Canada pipeline moving natural gas from western to eastern Canada passes through Geraldton roughly 70 miles south of the property. Topography: The surface features in the area are typical of a sizeable portion of the Precambrian Canadian Shield area. Many lakes, low swampy areas, and glacial moraine-type features are common in this recently glaciated area. The average elevation is between 800 and 900 feet above sea level, and the relief is probably less than 100 feet with the greater portion of the area less than 50 feet. The topographic "highs" are formed either by outcrops that were resistant to glacial erosion or by moraines, eskers and drumlins which were deposited upon the recession of the glaciers. The better mineralized zones, composed chiefly of quartz and magnetite, commonly form ridges resistant to erosion and weathering. Previous Work: Because of the obvious outcrop of the magnetite-rich beds and knowledge gained from early developments within the general region, it is conceivable that the presence of the iron formations has been known for a good many years. The area is included in studies made by L. F. Kindle* in 1929 and 1930 for the Ontario Department *Kindle, L.F., Kowkash-Ogoki Gold Area, Ontario Department of Mines Annual Report, Vol. XL, Part IV, 1931; map 40f

Jan 1, 1961

By Peter J. Tarkoy

A great deal of attention has been directed toward the complexities and inadequacies of exploration and pre-bid geotechnical information for heavy construction projects, differing site conditions, and the adversary relationships which generally develop as a result. The adversary position has been maintained at all cost. The solution is simple, if not easy. The solution requires strict and equal adherence to given principles by all parties involved, throughout the life of the project, from conception to completion. It is necessary to review and redefine some basic concepts, without value judgements, from a context of getting the job done. In a recreated context, the role of truth, judgement, responsibility, and integrity, in exploration, engineering design, construction estimating, and project construction, will be examined. It is suggested that anticipated geotechnical conditions be defined unconditionally. The alternative choice is to give the bidder the opportunity of making the interpretive judgements based on geotechnical data. Similarly, a unilateral method of establishing encountered conditions that are agreeable to both owner and contractor, must be outlined prior to contracting. As anticipated and encountered conditions are firmly and accurately established, significant differences can evaluated based upon limitations specified in the contract documents. Impact of differences on project costs can be fixed by pre-defined methods.

Jan 1, 1983

By M M. Collisson

The Synthetic Rutile (SR) plant operations, North Capel, produce electrostatic precipitator (ESP) fume and kiln scrubber residue. Typically ESP contains about 18 per cent Ti, 13 per cent Fe, 0.5 per cent Mn, eight per cent Si, six per cent Al, 16 per cent C, 0.9 per cent Zn, 0.6 per cent Pb, 300 ppm As, 300 ppm Cr and 5 ppm Cd. These wastes are held in a storage dam together with neutralised acid effluent (AE) liquor. A project was initiated to treat the fume and produce a benign residue that could be delivered to landfill, reducing dam space storage. Plant AE, containing free acid (9 - 14 g/L), Fe (6 - 7 g/L) and Mn (1 g/L), was used to leach ESP. The degree of extraction achieved for various elements include about 20 per cent Zn, almost 50 per cent As, five per cent Al, 0.4 per cent Pb and 15 per cent Cd. Extraction was most effective at pH The residue from AE leaching still contained Pb. TCLP tests of the leach residue produced Pb extraction significantly higher than the 0.1 ppm stipulated by Class 2 landfill guidelines. Other elements (eg As, Cd, Cr) successfully met the limits. Further leaching of the residue with EDTA extracted up to 65 per cent of Pb content. TCLP tests on treated residue showed Pb leaching potential of Lead was removed from the leach circuit as the sulphate by acidification of EDTA leach liquor, allowing EDTA to be recycled. The study showed that one waste stream can be used to treat another and help reduce plant waste.

Jan 1, 2001

By A Raza, D P. Kohn, D A. Foster, A J. W Gleadow

A large and increasing data base of apatite fission track results from sedimentary and granitic rocks exposed within the south-eastern highlands and along the continental margin ofAustralia provides constraints for the tectonic development of the south-eastern passive margin. The fission track results suggest that many regions of the south-eastern margin of Australia experienced distinct episodes of relatively rapid cooling during the middle Cretaceous to early Tertiary that can be attributed to the effects of rifting. One cooling episode is middle Cretaceous in age and related to denudation of the south eastern highlands from Tasmania to northern New South Wales between ~90 - 100 Ma. Rocks exposed along the present coast line record a later episode of rapid cooling, which is diachronous and decreases in age northward from ~80 to 90 Ma in northern Tasmania to southern New South Wales, ~60 - 80 Ma in central and northern New South Wales, and to ~50 - 60 Ma in southern Queensland. The results are consistent with models suggesting that underplating occurred inward of the rift along the eastern margin of Australia as a result of the onset of continental extension in the Tasman Sea at ~96 Ma. This resulted in a significant change in base level and km-scale denudation of much of the southeastern highlands. Subsequently, as breakup commenced during the Late Cretaceous at ~80 Ma and continued into the Paleocene at ~60 Ma, the second stage of cooling was imprinted on the rocks along the margin. This cooling is probably due to the relaxation of elevated geothermal gradients associated with rifting as well as some denudation. Because rifting was oblique to the present-day coast, different regions record different ages of cooling associated with the rift. The southern regions of New South Wales and Victoria yield ages associated with earlier rifting while regions of northern New South Wales and southern Queensland give ages associated with later rifting.

Jan 1, 1995

By J Kelly, C Kelsey

The Autogenous Kelsey Axial Displacement (KAD) mill is essentially a short retention time centrifugal mill, designed to effectively harness extraordinarily high concentrations of input energy for efficient particle size reduction. The mill which has an operating duty band extending from primary to ultra-fine also has the unique capacity to generate fine and ultra-fine products from single stage size reductions of either coarse or fine mineral feeds, in both wet or dry operating modes. This paper covers developments following a recent optimisation programme which confirmed that mill shell speed and the velocity differential between the shell and the rotating internal disc assembly tips could be optimised in relation to specific energy for a given feed rate and feed size providing the product size remains constant. Subsequent test-work further demonstrated the versatility of the mill with duties ranging from the removal of surface contamination associated with heavy mineral concentrate particles to the production of premium ultra-fine talc, from a single stage of size reduction. Open circuit grinding of a rougher gravity concentrate to liberate gold ahead of leaching also highlighted the scope for the application of low cost KAD milling for a range of hydrometallurgical feed preparation duties, which involve fine and ultra-fine grinding.CITATION:Kelly, J and Kelsey, C, 2013. Advanced media-free fine and ultra-fine grinding - The Kelsey axial displacement mill, in Proceedings MetPlant 2013 , pp 152-161 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Randolph R. Dreher, Michael L. Schreder

"In recent years, FFE Minerals has designed, installed and commissioned several large grinding mill circuits. This paper discusses the issues related to the erection and commissioning of large grinding mill circuits. The three circuits discussed are Collahuasi in Chile, Minera Los Pelambres in Chile, and Century Zinc in Australia. These circuits include large SAG and ball mills with both gear and gearless drive arrangements, as well as, both trunnion and shell supported mills. Aspects of these features are discussed with respect to their impact on installation and commissioning. While the normal challenges of mill erection and start-up were experienced, there were also a few unexpected challenges encountered partly due to the large scale of the equipment. An overview of the equipment and design ratings of these circuits is also provided.COLLAHUASIOverviewThe Collahuasi mills were started-up in November of 1998. The site is located in the Andes Mountains at an elevation of 4300 meters. The grinding circuit includes two lines featuring one SAG mill and one ball mill for each line. The circuit features a recycle conveyor around the SAG mills with provision for adding a pebble crusher in the future. The design tonnage of the grinding plant is 60,000 MTPD with an ore BWI of 10.5 kWh/MT.The SAG mills are 32’ x 15’ (1 3’ EGL) with 10,800 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The mills are driven by low speed synchronous motors with CCV variable speed drives. The SAG mills are trunnion supported and use hydrostatic lubrication. Feed to the SAG mills is via a rock-box type feed chute on a cart. The mills discharge on to trommel screens with a bucket wheel to remove the oversize.The ball mills are 22’ x 36.5’ (36’ EGL) with 12,500 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The fixed speed mills are driven by low speed synchronous motors with GE Quadramatic load sharing drives. The ball mills are shell-supported and feature multi-pad bearings with hydrodynamic lubrication. The mills are fed via a rubber lined sump box with feed spout on a cart. The ball mills also discharge on to trommel screens. Twenty-six inch (26”) diameter hydrocyclones are in closed circuit with the ball mills."

Jan 1, 2001

By S. du Plessis

Nationalization is high on the policy agenda in South Africa. This paper considers the case for nationalizing the local mining sector from an evidence-based perspective, which is derived from theoretical considerations and related to the known features of the South African mining sector and economy. A strong case against nationalization emerges, which can be summarized as follows. The mining sector is competitive and therefore a poor candidate for public ownership. Furthermore, the resources sector does not dominate the South African economy nor does it create the risk of a decrease in the competitiveness of the industrial sector via the unintended adverse impact of an appreciating real exchange rate due to a commodity boom (Dutch Disease). Nationalizing the mining sector will cost the government more than it receives. This is not only a bad idea in itself, but it will limit the scope for distributive policies on the national budget. The contemporary international experience demonstrates the risks of fiscal imprudence. Finally, nationalizing the resources sector will undermine support for those very market-based institutions required to achieve a higher long-run growth trajectory.

Jan 1, 2013

By Poltak Sinaga

PT Kaltim Prima Coal?s 13-km (8-mile) overland conveyor (OLC) was commissioned in 1991. It is a conventional three-roller, 35 degree trough belt type. Cost and performance optimization during initial design resulted in a 5.4-m/sec (17.7-ft/sec) belt speed, 1,000 mm- (40 in.-) belt width to convey 1.35 kt/h (1,490 stph) and 7 Mt/a (7.7 million stpy) of coal. Despite a high initial figure, the belt speed was lifted to 6.5 m/sec (21 ft/sec) in 1996 to accommodate mine throughput in-crease. In 2002, a new low loss ST2100 1,100 mm- (43 in.-) wide belt replaced the ST2250 that was due to be changed-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to increase the OLC capacity to 30 Mt/a (33 million stpy). Upgrading the OLC by increasing the belt speed was the lowest capital option. Increasing belt width and/or modifying the trough angle to have larger cross sectional area was not an economical option because it would require expensive changes and significant down time of the OLC. To achieve 30 Mt/a (33 million stpy), the belt speed had to be increased to 8.5 m/sec (28 ft/sec). Although such high belt speed looked feasible, there was no information at that time of other OLC operating at such high speed. There was a risk that the conveyor would not operate safely and reliably at higher speeds. This risk was escalated by the fact there was no facility to lower or fine-tune the belt speed once the higher belt speed was implemented.

Jan 1, 2009

By Turgut Yalcin

"High-grade concentrates are achieved in flotation columns primarily due to the use of thick froth layers and wash water, both of which facilitate the drainage of hydrophilic minerals from the froth. However, conventional columns employ tall, non-agitated recovery sections for bubble-particle attachment that require high headroom and special gas spargers as well as imposing particle size limitations. These disadvantages can be all alleviated by carrying out the recovery part of the process in a mechanical or pneumatic cell which generate froth more conveniently and efficiently.This paper describes the combining of mechanical and column flotation in a single unit and discusses the influence of various parameters on the performance of the system.INTRODUCTIONIn a flotation process, some of the minerals lifted up to the froth phase may drain back to the pulp due to various reasons such as weak attachment of particles to air bubbles, bursting of air bubbles, agitation of froth, etc. Weakly floating and entrained hydrophilic minerals drain at a faster rate than the strongly floating minerals, and effective exploitation of such differential drainage can lead to cleaner concentrates.For a given mineral, if the rate of flotation from pulp to froth is k1 (min·1) and the rate of drainage from froth to pulp is k2 (min""1), then the net (overall) flotation rate of the mineral, k (min-1 ), will be [Lynch et al., 1981 ]:"

Jan 1, 1997