Search Documents

By G. Kim

The influence of bacterial growth phase on the flotation behavior of malachite has been investigated in a well-controlled Hallimond tube system. The microflotation tests were conducted for malachite (45?53 µm) using different amounts (bulk phase concentration=1×108?5×109 cells/mL) of Rhodococcus opacus (R. opacus) as a collector, which was grown at mid-exponential versus stationary phase, at a constant speed (340 rpm), pH (6), and malachite-bacteria interaction and flotation time (each 10 min). Hug differences between R. opacus cells in mid-exponential and stationary phase was observed from the results for electrophoretic mobility and flotation tests. Specifically, the isoelectric point of the cells in the stationary phase was lower than that in the mid-exponential phase, suggesting that the amount and distribution of surface functional groups onto cell surfaces are likely different. Additionally, the cells in stationary phase led to significant increase in the flotability compared to those in mid-exponential phase over the background bacterial concentration level of 1×108?5×109 cells/mL. Furthermore, the flotation efficiency tended to increase with increasing cell dosage for stationary phase cells while no distinct difference was observed for mid-exponential cells.

Feb 27, 2013

By Michael Rehbock-Sander

The Gotthard Base Tunnel (GBT) is 57 km (35 miles) long and consists of two par-allel single-track tubes with an ex-cavation diameter ranging from 8.8 to 9.5 m (28.8 to 31.2 ft). These are interlinked by cross-passages every 312 m (1,000 ft). Two multifunction stations (MFS) are located in the sections Sedrun and Faido, at one-third and two-thirds of the entire tunnel length (Fig. 1). These will be used for the diversion of trains to the other main tube via tunnel crossovers, for the housing of tech-nical infrastructure and equipment and for potential emergency stops. To reduce construction time, the GBT was divided into five sections and was excavated from several sites simultaneously. The tunnel was excavated from the two portals, Erstfeld in the north and Bodio in the south, and also from three intermediate attacks, with their corresponding access tunnels, in Amsteg and Faido and two vertical 800-m (2,624-ft) deep shafts in Sedrun.

Jan 1, 2012

Physical testing of rock support for rockbursting conditions has been carried out for over 40 years. A review of this testing shows that it has been mostly component?based, rather than actually testing support systems. Further, it is concluded that none of the testing is truly representative of rockburst loading in a similitude sense. Similitude conditions are not achievable, mainly because the real conditions in a rockburst event, such as seismic source location and magnitude, wave frequencies, amplitudes, and interactions, are not all known. Because such information is not available, and because the results of all testing carried out to date have not been able to define, for support design purposes, the capacity of support systems, ongoing physical testing of rockburst support systems is essential. It is essential that the test should simulate, or actually take place in, a supported rock excavation. A rock support system is a combination of individual support components that work together to retain and contain the rock. In doing this, the components are subjected to loading by the rock and to interactive loading between one component and another. It is necessary to prove the capacity of such rockburst support systems by subjecting them to severe loading, as in direct blasting. The direct blasting approach, pioneered more than 40 years ago, probably still provides the greatest validity as a significant test of rockburst support capabilities, even though it does not simulate a rockburst. Direct blast testing of rockburst support systems in a surface environment, such as in a quarry or on exposed rock cutting surfaces, could represent a practical development of the approach, facilitating the execution and monitoring of tests.

Jan 1, 2012

By L. Sahu, S. Bhattacharya, S. Dey

"An ideal procedure to determine the limits of flotation-based separation, as is the case with washability analysis for density separation, does not exist. Therefore, a procedure called release analysis, considered to be the counterpart of the washability process in density separation, was developed to evaluate the flotation characteristics of coal fines. Since flotation is a complex process it is necessary to know the maximum recoverable yield that could be achieved at a target ash level and what could be obtained by release analysis. Due to a number of limitations in the initial procedures, modifications were recommended by various researchers to generate an optimum separation curve. This paper presents a review of, and a discussion on, the chronological evolution of release analysis methodology over the decades. Notwithstanding the availability of a standardized release analysis procedure, such as BS 7530, the paper highlights the critical parameters involved in the procedures, such as coal type, feed characteristics, choice of reagents and dosage, operator bias, and design features of the flotation cell IntroductionCoal is a heterogeneous substance consisting of various combustible constituents (macerals) and associated mineral matter. The kind and abundance of the various macerals present in the coal, such as vitrinite, semivitrinite, exinite, and inertinite, determine the type of coal. As macerals are formed by biological degradation of different parts of the plant material, they have different properties based on their original composition. Coal cleaning processes are dependent on the differences in physical properties between the coal components (the macerals) and also between the macerals and the mineral matter. Thus the cleaning characteristics of the coal might vary from one type to the next. The cleaning processes influence the distribution and the concentration of macerals in the various size and density fractions of the cleaned product."

Jun 1, 2019

By R. Larry Grayson, Joel R. Warneke

The mining industry has searched for a message that will resonate with the public while focusing on the industry’s positive contributions to society. So far, environmental groups remain unconvinced and the public is still largely uninformed. In the authors’ opinion, a number of recent events and experiences have converged to help shape a more effective public communication on mining’s important role. This article presents a perspective on coal’s role in sustaining society by anchoring the message in a transparent way, including a material flow analysis, that links coal’s impacts across a range of social and environmental aspects. Past and continuing image problems In her 1994 paper, Nancy Bingham, with Caterpillar, outlined what the public thought about mining. Based on extensive interviews, the following results were found: • The public believed mining harms the environment. • The public believed mining harms people in nearby communities. • The public believed mining exploits workers. • The public believed mining has little personal benefit to the individual.

Jan 1, 2006

By B. Yu, N. Verbaan, A. Mezei

The recent 20 years witnessed a boom and bust in the nickel laterite industry. Most notoriously is the story of the first three Western Australian nickel laterite projects which all suffered major ramp-up issues. Many hard lessons were learned by the industry and it has been widely reported that the major contributing factors included insufficient testing as well as a limited understanding of the materials handling characteristics at the front-end stage of the flowsheet. This paper compares the current "race to production" in the REE industry to the laterite industry 20 years ago and addresses the fundamental question: ‘Have mining and exploration companies with rare earth projects learned from past lessons and are they doing sufficient and appropriate testwork to prevent failure’? The authors will provide the perspective of a commercial metallurgical laboratory that has gone through the laterite cycle and is active in the present REE cycle.

Jan 1, 2014

By T. Lenarcic, R. Svrkota, J. M. McNeal, E. Prohic, S. Pirc

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Surface drainage samples, the usual media employed in mapping national territories, cannot be used for the geochemical mapping of carbonate terrains because there is no regular surface-drainage pattern on karst. Suitable sampling media have been studied in Yugoslavia, one-third of which consists of karst terrain. Sampling designs for the work were based on analysis of variance techniques. During initial investigations of various sampling materials in NW Yugoslavia sediment and aquatic moss from karst springs, along with soil, were established as the most appropriate media. Modified sampling procedures were then carefully applied along the entire Yugoslav karst belt, which includes terrains of contrasting topography, climate, pedology and vegetation. The studies indicate that climate and relief do not systematically influence the geochemical composition of soil. Regional and local variability was assessed for 21 chemical elements and the feasibility of producing stable regional geochemical maps was determined for a number of elements on the basis of sampling aquatic moss and sediment from karst springs and soil

Jul 1, 1991

By Steven Dapp

A new hyperbolic model for generating P-Y curves is developed for use in lateral analyses of cemented soils (a ?C-F? soil with both cohesive intercept and friction angle), and includes degradation of the static loading soil response to model the effects of load cycling (repeated loading) with load cycle number. The p-y curves, for both static and cyclic loading, were derived from full-scale lateral test results conducted on a set of six drilled shafts in a loess deposit at the Kansas DOT test site. Values of the model parameters obtained from the load testing at this site are presented, as well as a discussion of the model parameters effect on the results such that the model may be rationally applied to other sites with C-F type soils. A step-by-step procedure is presented to illustrate the application of the model. Correlation of the model to the CPT cone tip resistance (qc) from CPT testing is made, as this was found to be the most reliable; However, the model is applicable to other methods, both in-situ and laboratory, of assessing the soils strength.

Jan 1, 2011

By D. Brand

"The risk management objective of the AMIRA Code of Practice for Metal Accounting has seldom been systematically investigated in the literature up to the authors’ knowledge. Risk is defined in the Australian Standard on Risk Management (AS/NZS 4360:2004), as “the chance of something happening that will have an impact on objectives”. The simplified economic analysis performed in this paper has lead to define “something happening” as measurement non-representativity and “impact on objectives” as NSR loss from the optimal NSR. This has pinpointed a missing link being the establishment of a relation between NSR in flotation plants and measurement representativity. The proposed framework, referred to as the total cost of representativity, answers the previously unanswered question of how much accuracy/reproducibility is fit for purpose in a given flotation plant. Authors readily acknowledge that it is way easier to assess the cost of accuracy/reproducibility than the cost of inaccuracy/irreproducibility. However, this exercise not only answers previously unanswered questions but also establishes an essential link with operational excellence. This paper exposes why such operational excellence could neither be attained nor proved without a state of the art metal accounting system. This should impact not only how metal accounting systems are audited/designed/refactored, but also how flotation plants are designed.IntroductionBecause representative metal accounting is a vital source of information for the financial accounts of a mining/metallurgical company, the need for a code on metal accounting was recognized in 2001 and a team was formed in 2003, under the sponsorship of several major mining houses, to produce such a code. Table 1 exposes the two main objectives of this AMIRA Code of Practice for Metal Accounting."

Jan 1, 2017

By J. Drelich, J. Pletka

Lost foam casting patterns are foamed polystyrene shapes glued together into the shape of the part to be cast and are coated with a refractory material consisting of a mineral mixture and binders. Prior to casting, a significant number of the patterns are damaged and inevitably land-filled. In this study, a process is developed for the recovery of foamed polystyrene from the coating and glue contaminants. The process consists of shredding, impact comminution, size classification and density separation. It is successful in separating up to 97% of the contaminants, while recovering 95% of the polystyrene.

Jan 1, 2001

By G de Jong, W Sunyoto, K Sari, P Silalahi

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Big Gossan mine is operated by PT Freeport Indonesia and is one of the largest stope-and-fill mining systems in the world. The Big Gossan deposit is a ~200 m wide, 1200 m long and 500 m high steeply north-east-dipping to subvertical skarn body at the Cretaceous-Tertiary Ekmai-Waripi contact. The copper-gold mineralisation, with a 1.3 per cent copper equivalent cut-off grade, occurs mainly proximal to the Ekmai-Waripi contact in the garnet-clinopyroxene prograde skarn at the base of the Tertiary Waripi formation and partly distal to the contact in the tremolite-actinolite retrograde skarn of the Tertiary Waripi formation.The Big Gossan stope mine is designed from 2540 m to 3020 m above sea level. Present active stoping operations occur at level 2540 mL to level 2640 mL and are done in a primary and secondary stoping sequence. The width and length of the stopes is 15 m and 20 m respectively, while the height of the stope varies between 20 m and 40 m, depending on the ground conditions. The stability of the stopes is visualised in the Mathew’s Stope Stability graphs. These graphs and actual Cavity Measurement Scanner measurements on the stope will predict and show the overbreak and underbreak, which affect the reconciliation of the mined stope and also the pillar stability between the primary stopes. Geological factors like major structures, joints, veins and alteration intensity are important factors that correlated with the stability of the Big Gossan stopes.CITATION:Sari, K, de Jong, G, Silalahi, P and Sunyoto, W, 2015. Stope stability at the Big Gossan skarn deposit, Papua, Indonesia, in Proceedings PACRIM 2015 Congress, pp 139–146 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Monika Patrycja Polak - Micewicz

This paper presents an approach for estimating the fatigue life for the base of powered roof supports (shield) manufactured by the FAZOS roof support company. FAZOS?s powered roof supports are designed to operate on an inclined coal seam in full caving with a medium, strong roof strength. This shield support is utilized in conjunction with a shearer and face conveyor for a complete longwall mining system. To design shield support, it is essential for contractor to know the physical (hardness, toughness, etc.) and mechanical properties of material (tensile strength, Young?s modulus, etc.) used for the shield support as well as the geotechnical properties of the mine site. The fatigue strength of the shield support material depends on the mean stress, alternating stress, cycle frequency, transport dimensions, mine environment and other factors. In order to estimate the fatigue life for a powered roof support system, it is assumed in this paper that the support must keep the roof stable in the mine under variable load cycles. The approach selected in this study contains Goodman?s model (Goodman, 1899) for all blocks in the design housing which is subjected to sinusoidal load. On this basis, the degree of fatigue damage was calculated and compared to the results of experimental tests. It will be shown that there is a significant detrimental effect on the fatigue life of the base of the powered roof supports due to geometrical notches. The Ramberg-Osgood model and damage accumulation rule (Palmgren-Miner) (Miner M., 1945) were used and numerical analyses were conducted, utilizing ANSYS finite element software. These analyses play a very important role in longwall casing design. The proposed method allows assessment of the yield state and forecast of the structure cracking, taking plastic strains occurrence into account. The presented method is universal and can be applied for fatigue life estimation of other subassemblies of powered roof supports. The final portion of the paper presents results of variable amplitude loading simulations on the S355N and S690Q steel used to make powered roof supports. The results of the physical tests were compared with the results from finite element methods. The proposed approach to calculate fatigue life gives the best correlation between the experimental results and calculated values of fatigue life for the powered roof support base. Finally, the design process uses a simple approach to predict fatigue life in a short time, reducing design costs and providing longer service life for roof supports.

Jan 1, 2012

The following brief observations on the mineral composition of the Mt. Oxide copper ore are intended to supplement the geological description of that ore-body recently published by Blanchard (2).'" The Mt. Oxide copper mine is situated about 45 miles W.N.W. of Dobbyn, in the Cloncurry district of Queensland (Fig. 1). A representative suite of specimens from the mine was obtained through the kindness of Mr. P. B. Nye, Executive Officer of the Aerial, Geological and Geophysical Survey of Northern Australia, and Mr. Jack Hall, the tributor of the Mt. Oxide mine. The specimens, as shown in Fig. 2, were nearly all from the sulphide zone, between the l04-ft. level and the 300-ft. level. Several additional specimens, together with information which will be referred to later were kindly sent to me by Mr. Roland Blanchard.MINERAL COMPOSITION OF THE COPPER OREThe mineral composition of the ore is relatively simple. It consists essentially of chalcocite, with varying, but minor figures...

Jan 1, 1940

By Lowell Stroud

This report is the third in a series presenting equilibrium vapor-liquid data for helium-bearing natural gases. The first two reports contained phase data for the gases processed for helium at the Bureau of Mines Amarillo and Exell, Tex., helium plants. The present report offers similar information for a lower-helium-content (0.75 mole-percent) natural gas to be processed in the Department of the Interior's long-range helium-conservation program. A windowed-cell apparatus was used to obtain 218 samples of equilibrium vapor and liquid phases at 73 experimental conditions ranging in temperature from -100° F to -275° F and in pressure from 100 to 500 psi. From the phase data, the condensation characteristics, helium solubility, and equilibrium-vaporization-coefficient data for helium, nitrogen, and methane were evaluated. The effect of using a. preliminary hydrocarbon trap upon the subsequent vapor-liquid compositions is reported. A brief comment regarding the composition effect of passing the gas through a gasoline-removal unit is also included.

Jan 1, 1963

By O. Dojcar

The results of a laboratory investigation of rock fragmentation conducted with a model material were partially verified under field conditions. The object of the investigation was to study the qualitative and quantitative relations between the parameters of the primary blast and fragmentation to enable the planning of an economically efficient degree of disintegration with optimum utilisation of the blast energy. The three blast parameters that were considered were burden, specific charge and the ratio of spacing to burden

Jan 1, 1991

By Neal Lee, Braden T. Lusk, Brendan McCray

Determining the minimum amount of inert material that can be used between explosive columns is a complex problem. Using too little inert material can result in detonator/primer failure, either by sympathetic detonation of or failure to fire of the subsequent explosive column(s). Propagation type failure results when inert material length between charges is small enough that the subsequent (delayed) deck fires more or less instantly. In this situation, the primer, detonator, or bulk product is initiated by the shock wave from the earlier firing deck. This type of failure may be un-noticed until the vibration/airblast report is examined.

Jan 1, 2016

By Othon do Rêgo Monteiro Neto

[The present study has investigated the extraction of copper from a chalcopyrite flotation concentrate using an adapted strain of Thiobacillus ferrooxidans and shake flasks, tank leaching and Warburg respirometer techniques. From the shake flask experiments, the activation energy and the frequency factor have been determined to be ?ka = 59.4 kJ and A = 3.3 x 105 S-1, respectively. The temperature coefficient was found to be Q10 = 2.2 in the range of 20 to 35°C. It was suggested that the reaction mechanism of chalcopyrite leaching by T. ferrooxidans involves the formation of an activated complex. whose thermodynamic values have been calculated to be ?G? = 92.1 kJ, ?S? -148.8 J K-1 and ?H$ = 47.8 kJ. The maximum volumetric oxygen mass transfer coefficient for the reactor leaching was found to be achieved by using an optimum air flow rate of 1970 cm min l at a rotational frequency of 1000 min-1. The highest copper extraction in tank (reactor) leaching experiment was 86.8% after 17 days of leaching, while in the sterile runs the corresponding copper extraction was only 40.1%. The copper extraction was suggested to be diffusion controlled. The power requirement of the aerated reactor was calculated to be Pg = 2.02 watts. During leaching, the oxygen saturation concentration was found to be C* = 6.70 mg dm-3. Using the gassing out method the critical oxygen concentration was assessed to be CCrit 0.05 mg dm 3. From the Warburg experiments, the kinetic parameters of the Monad equation were derived with a new evaluation technique to be Vmsp = 9.0 µm3 02 min-1 mg protein-1 and K = 7.4% pulp density for the effect of substrate concentration. The order of reaction and the overall reaction rate constant were determined from the modified van't Hoff plot to be n = 0.0 and k = 1.49 p dm3 02 min-1 mg Protein -1 for the chalcopyrite concentrate oxidation by T. ferrooxidans. On the basis of this experimental work, a preliminary flow sheet has been proposed for the bioextraction of copper from flotation concentrates.]

Jan 1, 1985

By Franz Kolmbauer

At Primetals Technologies Brazil Ltda. Rio de Janeiro Santa Cruz Workshop we electroplate mold coppers for continuous casting by tank plating. Tank plating submerges the copper in the bath of the plating solution. This is the most common method of plating and is applicable for both broadface and narrowface copper plates. Mold copper plates have a decisive impact on the product quality as well as the cost for maintenance and production. A perfect understanding of the operational influences on the plates and performance variables are the first step for the right selection of a copper plating method. Variable Hiper Coat keeps the Copper Plates 50% up to 100% longer in operation because of applying hardness on the Copper Plate where it is needed. Primetals Technologies Brazil provides the solution which meets and exceeds the requirements for todays and future demands.

Aug 16, 2017

By William G. Szymczak

A set of experiments were conducted at the Aberdeen Proving Grounds [1] in which explosive charges were buried in saturated sand beneath a suspended rigid platform. The goal of these experiments was to measure the dependence of the impulse transmitted to the platform on the standoff distance and the charge burial depth. Simulations of these experiments were performed using the BUB2D axi-symmetric code using a frictional-cohesive visco-plastic model to describe the response of the saturated sand. This code solves a constrained set of conservation laws in which the liquid region (in this case saturated sand) is assumed incompressible. The explosion is initialized as a high pressure gas bubble (void) within the fluid. Comparisons of the simulations to the experiments are presented together with a study of the physical phenomenology associated with the loading process. In particular, it is shown that the force imparted to the platform is a combination of the impact of the sand on top of the explosion gas bubble and the pressure of the bubble as it expands before venting into the atmosphere. Under certain conditions, when the platform standoff is sufficiently small and the platform is sufficiently large, the bubble can over-expand before venting and pull the platform downward. This phenomenon was studied further through carefully measured and photographed small-scale experiments performed at the University of Maryland [2]. The small-scale experiments provide additional important validation benchmarks for our model.

Jan 1, 2005

By L. Arnberg, E. Ott

The microstructure of ferrosilicon is important since it controls the disintegration of the material during crushing and thus the generation of fines. Therefore a study of the microstructure formation during solidification of pure FeSi(75wt%Si) and FeSi(75wt%Si) containing 1.2wt%Al and 0.2wt%Ca has been initiated. The material has been cast into rods of 8mm diameter, which have been remolten by induction heating and directionally solidified in a Bridgman apparatus. This allows the temperature gradient and the growth rate to be controlled independently. The temperature history during solidification has been recorded by a thermocouple in the melt. Growth rates have been varied between 5 and 400µms-1 and temperature gradients between 3 and 14°Kmm-1. The microstructures show a large dependence on the solidification conditions. The crack formation in the alloys has been studied and found to be strongly related to the microstructure.

Jan 1, 2004