Search Documents

Laboratory electrical resistivity measurements of rocks are reviewed. Inductive and galvanic methods are discussed together with the ten important experimental factors which should be considered in an investigation.These experimental factors are electrodes, sample preparation, measurement errors, temporal current variations, current density, frequency, electrolyte composition, electrolyte saturation, pressure, and temperature.

Jan 1, 1969

By Anderson Ayres Bittencourt

O monitoramento de sistemas e ativos de automação sempre existiu de forma rudimentar e descentralizada. A análise desses dados tanto quanto sua obtenção é um desafio para as empresas atuais. Foi a partir deste princípio que nosso projeto foi desenvolvido.Este trabalho tem como objetivo demonstrar a solução de Monitoramento online e preditivo implementada na ArcelorMittal Aços Planos da América do Sul, onde desde o início de sua implementação pudemos capturar benefícios operacionais, melhoria dos processos, otimização, eliminação e/ou diminuição de indisponibilidade de plantas, entre diversos outros retornos que serão apresentados.

Oct 30, 2017

By Satyajit Vaidya, Rudolph Frizzi, Luis Berroteran

This paper presents design and construction challenges associated with a high-capacity rock-socketed drilled pile foundation system for a 60-story building recently constructed in an urban environment. The site is in very close proximity to surrounding 1-to-6-story buildings and a commuter rail subway tunnel structure. High compression, uplift, and lateral loads imposed by the tall, slender tower constructed over a relatively small site footprint posed a significant design challenge due to the close proximity of the subway tunnel and other structures. Construction challenges included those associated with advancing the drilled pile casings through overburden materials using internal flush method mandated by the Transit Agency, advancing the casings through very dense glacial till materials encountered above top of rock, and drilling rock sockets in variable rock conditions. This paper provides a brief overview of the site and subsurface conditions, and discusses the resulting design and construction challenges for the drilled pile foundation system and how they were addressed. SITE AND SUBSURFACE CONDITIONS The 8,350-square-foot site is located in a busy neighborhood in downtown New York City (NYC). Buildings neighboring the site are supported on shallow foundations, and their basements extend about 15 feet below the sidewalk level. A NYC-Landmarked building is located within a NYC Department of Buildings (DOB)-designated 90-foot influence limit from the Project site. NYC Transit Authority (NYCTA) subway tunnel and station structures are located in close proximity to the Project site. The subway tunnel structure extends about 50 to 55 feet below the sidewalk level. Although the upper portion of the tunnel structure is about 13.5 feet away from the site property line, the lower portion is only about 1 foot away from the property line. A site location plan is presented as Fig. 1. Geotechnical borings revealed subsurface conditions generally consisting of successive strata of surficial fill, sandy and silty soils, and glacial till (predominantly consisting of cobbles and boulders) overlying mica schist bedrock. A generalized subsurface profile is presented in Fig. 2. The surficial fill stratum was about 10 to 23 feet thick, and generally consisted of loose to medium dense sandy soils with varying proportions of silt, gravel, and miscellaneous debris such as brick. The underlying sandy and silty soil stratum was about 60 to 79 feet thick and generally consisted of loose to medium dense inter-bedded layers of fine to coarse sand, silty fine sand, and silt. The underlying glacial till stratum was about 26 to 70 feet thick and generally consisted of cobbles and boulders embedded in a very dense soil matrix. Top of bedrock was encountered in the borings about 110 to 150 feet below sidewalk level. Groundwater level was measured at about 30 feet below sidewalk level.

Jan 1, 2018

The corrosion behaviour of a low carbon steel was investigated in natural seawater and various synthetic seawaters. It was found that the steel corroded nearly four times faster in a 3.5% NaCl solution than in natural seawater for an exposure time of 21 days. The corrosion rate after immersion in synthetic seawaters (ASTM D1141 and Marine Biological Laboratory seawater) is similar to the corrosion rate after immersion in natural seawater. Calcium carbonate (aragonite) deposits were found on the surface of the steel after immersion in natural seawater and the synthetic seawaters. Some magnesium-containing deposits were also found after immersion in the natural seawater. These deposits act as a barrier against oxygen diffusion and thereby lower the corrosion rate. The morphology of the calcium carbonate deposits that formed during immersion in the natural seawater is different from those formed during immersion in the synthetic seawaters. This may explain the slightly lower corrosion rates obtained in the natural seawater. X-ray diffraction also showed that the oxy-hydroxides formed in the 3.5% NaCl solution differed from those formed in the other solutions. Keywords: Corrosion, seawater, low carbon steel, 3.5% NaCl, aragonite

Jan 1, 2006

By J. Drzymala

Particle beneficiation tests are often conducted to determine how the recovery of a key component of a particle mixture varies with overall product yield, i.e., the separation curve. The results can be misleading when an attempt is made to determine the effect of feed grade by comparing separation curves representing different feed grades or key component concentrations. This is a shortcoming of the conventional recovery versus yield diagram, which may not appear to be affected by feed concentration. To overcome this shortcoming, a method is presented for transforming and normalizing the recovery and yield coordinates so that the separation curves representing dif-ferent feed concentrations are directly comparable.

Jan 1, 2007

By A. L. Wilder, S. N. Dixon

Introduction Coeur d'Alene Mines Corp.'s largest precious metals property is located in the historic Rochester Mining District 40 km (25 miles) northeast of Lovelock, NV. The property encountered cold weather operational problems soon after its fall start-up in 1986 due to its elevation of over 1830 m (6000 ft). The problem of ice buildup on the heaps because of sprayed solution application was faced immediately. It was felt that allowing ice to build up all winter long until a spring thaw was impractical due to the large area under leach. Further, the operating cost and delivery schedule for a solution heating system was unacceptable. The development and installation of a leach solution distribution system using drip emitters made efficient, cost-effective winter operation possible. Other benefits of this system have also been observed and are discussed here. General process description 15,422 kt/day (17,000 stpd) of - 1.27-cm (-1 /2-in) crushed ore from the three-stage crushing plant are delivered to the leach pad using 77.1 t (85 st) rear dump haul trucks. The ore is drifted into place with a D-9 bulldozer. Leach panels are contiguous and are approximately 8861 m'(90,000 square ft) in area built in 6-m (20-ft) lifts. New panels are built on top of older areas to a final height of 61 m (200 ft). Each panel is ripped and cross-ripped prior to leaching. Barren solution is distributed to the heap using drip emitters at rates of 0.02 to 0.41 L/min/m2 (0.0005 to 0.01 gpm per sq ft), depending on the age of the panels. The pH of the leach solution is 10.7 with a cyanide concentration of 0.75 kg/t (1.5 lb per st). Approximately 50% of the silver and 80% of the gold are finally recovered. Pregnant solution percolates though the heap and flows by gravity into one of two 9.46 ML (2.5 million gal) pregnant solution ponds. The solution is then pumped to a conventional Merrill-Crowe process plant. Clarification takes place in three 9464 L/min (2,500 gpm) capacity filters. The solution is then pumped to a packed vacuum deareation tower for the removal of dissolved oxygen. Typical deareated solution contains 0.7 parts per million dissolved oxygen. Precipitation of gold and silver is accomplished by adding a zinc dust slurry to the deareated solution at the suction of the filter press feed pump. Precipitated gold and silver are recovered in three recessed plate and frame filter presses. Barren solution is discharged into a 11.7 ML (3.1 million gal) pond where cyanide makeup occurs. This solution is pumped back to the heap for further leaching. The precipitate filter cake, containing approximately 75% dore (Ag + Au), is then fluxed with anhydrous borax, soda ash, sodium nitrate and fluorspar to yield a neutral, bisilicate slag. The fluxed precipitate is then charged into a propane-fired melting furnace and heated to 1150° C (2100° F) for 3 1/2 hours. Slag and dore bullion are poured into conical cast iron pots yielding buttons of 800 to 1000 troy oz. The dore typically contains 98.5% silver and 1 % gold. Slag is crushed and tabled to recover the trapped dore blebs and beads. Concentrate from the table is returned to the furnace. Table tails are sent to the crushing circuit and out to the leach pad. Solution application The area kept under leach at Rochester is approximately 130 000 m2 (1.4 million sq ft). Barren solution is delivered to the pad at 21.2 kL/min (5600 gpm) for a resultant application rate of 0.16 L/min/m2 (0.004 gpm per sq ft). A traditional solution sprinkling system using No. 12 Senninger Wobblers with individual pressure regulators was installed at the onset of leaching activities. The Wobblers were placed at 9.1-m (30¬ft) staggered centers and were fed off of a gridwork of Yellowmine plastic piping. Solution flow rates were moni¬tored to each panel. The onset of cold weather with an average nighttime temperature of -12° C (10° F) made it apparent that continual operation would not be possible with the sprinklers. A significant amount of ice was built up on top of the heap, making maintenance and pipe removal dangerous, if not impossible. Leach solution application was restricted to daylight hours to inhibit ice formation. Process plant flow rates were reduced to maintain steady-state operating conditions. However, as daylight temperatures dropped below freezing, ice continued to accumulate due to the sprays. Besides the obvious operating hazards brought on by the growing icefield, there was also the potential environmental hazard associated with an early thaw melting the ice too rapidly for the solution containment facilities. One other option for preventing ice formation was heating of the barren solution prior to spraying. Initial plant design allowed for expansion of the propane storage and distribution system as well as modification of the barren piping for a solution heater. This option was not exercised because the operating costs for an adequate system would have been prohibitive, and timely delivery of a system was not available. An investigation was conducted on the various drip irriga¬tion products available, since subsurface solution applicators would eliminate ice formation altogether. Systems utilizing external flow emitters were ruled out because of their ten¬dency to clog when buried. Emitter systems using perforated tubing were also eliminated from consideration due to their inability to adequately control flow over required lengths of tubing. An in-line emitter system was finally selected which demonstrated clog resistance and adequate flow control, enabling direct burial.

Jan 1, 1990

The University of New South Wales (UNSW Australia) has been a world leader in the development of innovative virtual reality technologies over the last 15 years. AVIE (Advanced Visualisation and Interactive Environment) was developed by iCinema as a collaborative venture between UNSW?s Faculties of Engineering and the College of Fine Arts. This is the world?s first 360°-surround, virtual reality (VR) stereo projection theatre system. The School of Mining Engineering at UNSW Australia has developed 18 different virtual reality modules aimed at mine safety training and mining engineering education. These modules are being regularly used in both the mining industry and the university. The School of Mining Engineering is continuously involved in the development of different modules. Research is also currently being conducted on the implementation of other technologies into this environment. Artificial intelligence (AI) and fuzzy logic are tools that the authors would like to consider implementing in future module development. This paper will review current research in both these areas and consider options for applying these technologies.

Jan 1, 2014

By R. Weideman, M. Le Roux, F. B. Waanders, Q. P. Campbell, E. Fosso-Kankeu, D. Moyakhe

"*Paper written on project work carried out in partial fulfilment of B.Eng (Chemical Engineering) degreeSynopsisSpent coffee grounds were transformed into biochar using a hydrothermal method. Some of the biochar product was pre-treated through surfactant impregnation with sodium dodecyl sulphate (SDS) to enhance its adsorption capacity. The non-treated(NT) and pre-treated(PT) biochars were characterized using FTIR spectroscopy and SEM-EDS analyses, which revealed that the products had the potential for adsorption of heavy metals from solution and confirmed the successful impregnation of biochar with SDS surfactant. The two adsorbents were then used for the removal of cadmium from solution and the adsorption behavior and capacity determined through adsorption isotherm, kinetic, and thermodynamic studies. It was found that the cadmium was adsorbed in several concentric layers on the surface of the adsorbents through a chemisorption mechanism. The PT biochar was identified as a superior adsorbent, with a capacity of qe = 10.67 mg/g compared to the NT biochar with qe = 4.82 mg/g. The adsorption of cadmium onto the PT biochar was further determined to be spontaneous and endothermic. It was therefore concluded that the PT biochar shows potential as an adsorbent and could be considered for implementation in the treatment of metal-polluted effluents. IntroductionCoal mining operations are notorious for producing large amounts of waste tailings, which are disposed of in the form of a slurry on tailings dams. This inadvertently contributes towards environmental problems (Jin, Mansour, and Thomas, 2017). Heavy metals are one of the most common pollutants that originate from solid mine waste disposal facilities, and these can leach into groundwater supplies, contaminating them and rendering the water unsuited for human consumption (Salomons, 1995). Cadmium occurs in conjunction with metalliferous ores and can cause severe damage to agricultural soils and drinking water supplies in the vicinity of mining sites (Dudka et al., 1995). It has a tendency to migrate into the surrounding vegetation, which in turn can cause harm to humans and animals when consumed (Marquez et al., 2018)."

Jul 1, 2019

By Douglas R. Malicoat, Christopher J. Pritchard

Tg Soda Ash operates an underground trona mine located In southwestern Wyoming, which utilizes continuous mining machinery to produce 2.OM tpy (2.2M stpy) by shortwall and room and pillar methods. As the mine developed, the Increasing distance from the shafts caused travel times to be a significant factor in planning for mine emergencies. It was decided to construct a barricade chamber, a modified refuge chamber, to Increase safety and to provide an additional escape option in the case of a mine emergency. Fortunately, there has been no need to use these facilities during the last 9 years, but mine emergency planning has been greatly improved.

Jan 1, 1993

By Keith L. Harris

The performance of the world economy improved significantly in 1984. Real world output!/ grew 4.3% (compared with 2.6% in 19831, the highest since the 4.4% increase recorded in 1978 (table 1). The output of industrial nations rose 4.9%, while that of the developing nations rose 3.7%. The United States and Japan had the largest increases in output of the major industrial nations, with respective increases of 6.8% and 5.8% (table 2). The components of real output with the most significant growth in the industrial countries were gross fixed investment (9.2%), consumer expenditure (3.1%), and public consumption (2.5%) (table 1). Industrial output, as measured by industrial production indices, has returned to about the 1980 level for most of the major industrial nations (table 2). Exceptions to this were industrial production in Japan and the United States; Japan's industrial production rose steadily throughout the 5-yr period and is now more than 16% above the 1980 level, and the industrial production index for the United States reached 11 1.2 (1980=100.0). Real total domestic demand grew at 8.7% in the United States, more than double the rate of Japan, which, at 4.0%, had the second-largest growth. Average demand for all industrial countries was up 5.1%. During 1984 the U.S. dollar showed great strength on international markets, contributing to large current-dollar negative net exports of goods and services and even larger negative net exports of the merchandise sector. While growing U.S. imports helped spread the benefits of the recovery, they also led to a widening of current account imbalances and growing trade tensions throughout the world.3/, 4/

Jan 1, 1985

By S. Schina

Part of the Imittos Western Peripheral Motorway in Athens is the twin road tunnel in the vicinity of American College, with 20m excavation diameter. In the paper, the environmental and other requirements, the geometry and the geological – geotechnical characteristics of the rock formations in the construction area are given. Information regarding the modeling and analysis methods that are used for the design of the temporary support, the final lining and the wedge and slope stability analysis is described thoroughly. Finally, the results of the analyses are compared with these of measurements and general remarks during the construction of the tunnels.

Jan 1, 2001

By Peter Jackson

The dewatering of the large construction pits required for major infrastructure projects often has a significant impact on the environment. This is particularly so in urban areas and where groundwater resources are of interest. These environmental impacts are inter alia, groundwater lowering and the consequent effects such as settlement and deterioration of timber foundations, together with the impact of the dewatering on the groundwater quality. In order to minimise the environmental impact of the dewatering, the quantity of water to be abstracted and the amount of groundwater lowering in the surrounding area must be minimised. This paper describes the measures that have been taken on the Copenhagen metro project to achieve the objective of minimal environmental impact whilst still carrying out a major dewatering scheme.

Jan 1, 2000

By Gordon DM

Tyres account for 25-30 per cent of the operating costs of large capacity haul units as used in open-cut mines.Tyre operating costs can be substantially reduced and often contained in real terms by applying knowledge that is now available.This paper describes certain specific advances in tyre management, namely batching, bias adjustment, cumulative plotting and the so-called "pressure-temperature" system of tyre pressure control, originated on the Mt Newman Mining Company's Newman minesite, and discusses the contribution that each has made to improving tyre management and reducing costs.

Jan 1, 1983

Titanium and Zirconium Industries Pty. Ltd. separates rutile and zircon from heavy mineral concentrate recovered from sand dunes on the east coast of North Stradbroke Island, Queensland. Separation plant feed is delivered to Dunwich, on the west coast, by a seven mile aerial ropeway traversing the island. Mining and concentration is effected by two floating dredge-concentrators now operating on the beach 31; miles from the aerial ropeway terminal. Heavy mineral concentrate is transported hydraulically from the dredges to the ropeway through a 6 in. pipeline. Six pumps in series deliver 24 ton/hr of dry solids in a pulp containing 13 per cent solids. For maximum economy the transfer pumping system is controlled deliberately to cause transportation in the zone of incipient settlement of solids, ieat velocities below the limit deposit velocity for the particular pipe diameter, pulp density, and specific gravity of solids. Automatic density control, based on a combination of power consumption and pipeline pressure, eliminates the danger of plugging the line but periodic flushing is necessary to remove gradual accumulation of solids in the bottom of the pipe. After 15 months operation the pipeline was descaled with hydrochloric acid to remove severe blistering with rust nodules, regrowth of which is now prevented by continuous injection of inhibitors. After transporting 100,000 tons of heavy mineral the average wear on the steel portion of the pipeline was 0·01 in. and indications are that wear on the asbestos cement portion is less.DESCRIPTION OF OPERATIONSGeographyTitanium & Zirconium Industries Pty. Ltd. (T.A.Z.I.) operates on North Stradbroke Island, some 30 miles southeast of Brisbane, Queensland. The island is approximately 25 miles long and eight miles wide, and is bounded on the east by the Pacific Ocean and on the west by Moreton Bay (Fig. 1). With the exception of a small outcrop of volcanic 1. Manuscript received at The Institute. 8th May. 1962. This paper was presented at the Annual Conference of The Institute. 5th-11th August. 1962.

Jan 1, 1962

The purpose of this paper is to outline some aspects of the experimental worlr that has been carried out in the mineral dressing laboratory at M'ount. Morgan during recent years.The subject matter has been dealt with under the following headings:1. Comminution of various mill products.2. The application of sulphur dioxide as a flotation reagent.3. Heavy-media separation.4. Bulk flotation of sulphide ores.COMMINUTION OF VARIOUS MILL PRODUCTSThe following data were cbtained by processing fractions of reserve grade ore.Granular TailingIn Table 1 are shown the results of tests on material representative of average grade tailing. In the first test (H1 ) the granular tailing was floated as received and in the second test (Ha) the tailing was ground prior to flotation.

Jan 1, 1952

By K Blay, C McCamley, P Petrucci

The Newmont Boddington Gold (NBG) processing plant was designed for 35Mt/y with ball mills expected to deliver a combined new mill feed rate of 4837 tonnes/hr. Since beginning commercial production in late 2009, the plant has steadily increased throughput to meet design capacity in 2014 and reached 37 Mt/y in 2015. Through improved efficiencies, changes to the milling circuit have taken place since commissioning to take the plant beyond its design to an actual throughput of 39.0 Mt in 2017 and a budgeted throughput of 39.4 Mt/y this year.The NBG milling circuit has four parallel ball mills, each consisting of a 7.9 x 13.4 m ball mill with twin 7.5 MW fixed speed motors in closed circuit with twelve 650 mm cyclones. Each mill is fed by two wet screens with the undersize gravitating to a mill discharge hopper where it is combined with the ball mill discharge and pumped to hydrocyclones for classification. The cyclone underflow is re-ground to a target P80 of 150 µm.This paper will focus on process improvements made to the NBG milling circuit which include cyclone reconfiguration, fine screen panel redesign, implementation of an expert control system, mill power draw increase and grinding media changes to take NBG beyond its design throughput.CITATION:McCamley, C, Petrucci, P and Blay, K, 2018. Going beyond design at Newmont Boddington Gold, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 497–508 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By M. J. Stewart, F. Weinberg

PREVIOUS investigations into convective flow in molten metals have examined systems in which the length-to-height ratio of the enclosure is large, usually using long graphite boats.''2 In normal castings this ratio is generally small and it is not possible to extrapolate the results of previous work to casting configurations. The present investigation was undertaken to examine liquid flow in systems of low length to height ratio. The apparatus used for the experiments is shown in Fig. 1. The molten zone of tin is contained in an aluminum mold of inside dimensions 6.4 by 6.4 by 0.31 cm. A heating block containing a resistance coil is attached to one end of the mold and a cooling block is attached to the other end. These are used to produce a wide range of temperature differences across the mold. The mold is contained in a stainless steel tank which is heated from the outside by resistance heaters to give the required operating temperature during the experiment. Temperature measurements in the molten tin are made with an iron-constantan thermocouple PT equal to 5 atm. The phase diagram derived by us was the same as that found by Krivsky and Schuhmann, except for a similar discrepancy in one boundary line representing the gas composition in equilibrium with SO a. The vapor pressures of the pure components can be neglected at 1700°K, 1 atm and 2500°K, 5 atm. There-fore, in these cases PT is essentially the total pres-sure in the system. This is valid for all the diagrams presented by Krivsky and Schuhmann except for the one at 2500°K and 0.01 atm, where the vapor pressure of silicon is comparable to PT.6 This work was supported in part by the American Iron and Steel Institute. 'C. E. Wicks and F. E. Block: Thermodynamic Properties of 65 Elements, U S. Bur Mines, Bull. No. 605, 1963. R. P. Elliott: Constitution of Binary Alloys, 1st supplementary, McGraw-Hill Book Co., New York, 1965. 3W. A. Krivsky and R. Schuhmann, Jr.: Trans. TMS-AIME, 1961, vol. 221, pp. 898-904. 4M. F. Ancey-Moret, M. Olette, and F. D. Richardson: Mem. Sci. Rev. Met., 1964, vol. 61, pp. 169-76. 5J . F. Elliott and M. Gleiser: Thermochemistry for Steelmaking, vol. 1. Addison-Wesley, Reading, Mass. 1960. 6 J.Drowart, G. De Maria, and M. G. Ingraham: J. Chem. Phys., 1958, vol. 29, p. 1015. probe of 0.4 mm diam inserted into the open top of the mold. Radioactive sn113, in the form of a small sphere, was gently lowered into the molten tin at point A in Fig. 1 THERMOCOUPLE> WATER ARGON END HEATER QUENCH ARGON Fig. 1—Apparatus for detecting liquid flow. Point A indicates position the tracer was introduced.

Jan 1, 1970

Difficulties were experienced in the identification of carbonate minerals intimately associated with iron oxides in the so called carbonate ore, which occurs at depth in the Iron Duke Orebody.Determination of refractive indices by examination under the microscope using the immersion method, together with inferred chemical composition indicates that dolomite and parankerite are common constituents. Histograms of the manganese and sulphur contents strongly suggest that manganese is associated with the carbonate minerals, and that the highest sulphur assays occur near the base of the carbonate body.From the present work it is concluded that refractive indices indicate only a very approximate composition for carbonates of the parankerite type.The different carbonate minerals occur in irregular zones.INTRODUCTIONThe Iron Duke deposit is situated in the southern portion of the South Middleback Range on Eyre Peninsula, S.A., 30 miles from Whyalla. (Fig. 1).Drilling at Iron Duke revealed a large body of so called carbonate ore, which was tested in detail at cross section 1000 ft. S by three diamond drill holes, DDH.57, 67 and 78. (Fig. 2)Most specimens of carbonate ore described below were obtained from DDH 67 and 78.GENERAL GEOLOGYThe South Middleback Range is composed of two parallel ridges trending north-south. The Iron Duke orebody is situated on the southern portion of the western ridge. (Fig.1) .The rocks of these ranges belong to the Middleback Group which rests on a gneiss complex. Their age is considered to be Middle Precambrian or late Archaean.

Jan 1, 1963

THE ore treated is almost pure copper pyrites (chalcopyrite) in a gangue of quartz and quartz-felsite. Very little free iron sulphide (pyrite) occurs, and at the time of the erection of the flotation plant the stopes in the oxidized zone had been almostentirely depleted. This zone only extends to a shallow depth, and, below the l00-ft. level, the sulphide for the most part is clean and bright but in the crushed and brecciated parts of the ore channel, where surface water has circulated freely, the gangue is decomposed and kaolinized, and the copper sulphide badly tarnished. This class of ore gave considerable trouble at the mill, but unfortunately, was very limited in quantity. A sample of rich ore assayed-Copper, 21.2 %; iron, 24:.3 %; silica, 28.9 %; sulphur, 25.1%.The concentration in the original mill was effected by handpicking, jigging, and tabling. A considerable portion of the copper mineral arrives at the surface in the form of large lumps of very pure quality, eminently suitable for sorting out by hand.The rich ore is tipped over a grizzly at the shaft bins; the oversize hand-picked, and the undersize bagged direct.

Jan 1, 1912

"In mineral exploration and mining applications, it is sometimes necessary to reduce sampling error in order to improve representivity of individual sample assays. Historic efforts to reduce sampling error have relied on the belief that larger samples exhibit less sampling error. Justifications for this belief traditionally have coupled the binomial theorem with an ideal geological material consisting of ore and gangue particles of equal size and shape (an equant grain model) and empirical tests of geological materials, to illustrate an inverse relationship between sample size and sampling variance. To date, no proof exists of this sample size-sampling variance relationship in real geological materials exhibiting variations in grain size, shape, composition, and degree of liberation.Using first principles calculus and the formula for the mean, sample mass and sampling variance are proven to be inversely proportional in all geological materials. Distribution assumptions and physically ideal geological models are not used in this proof. Furthermore, algebraic manipulations of expressions describing the variances of equant grain models consistent with binomial, hypergeometric, and Poisson distributions reveal that these models also exhibit an inverse sample size-sampling variance relationship. Thus, the sampling behaviors of these models are numerically consistent with the sampling behaviors of real geological materials, and these models can be used to estimate sampling errors in real geological materials using simple sampling parameters."

Jan 1, 2007