Search Documents

By D. Harrington

Fine ventilation was discussed. much more 15 to 20 years ago than it is now, yet today there are tendencies in connection with ,-line ventilation (in fact, numerous ventilation systems have been installed in recent years) indicating that the lessons learned by bitter experience in the past either have been forgotten or lave not been brought to the attention of the present generation. Possibly, the mining min of today considers that conditions have changed so much that experiences of the past cannot be repeated today. At any rate, it seems desirable to restate some of the principles of mine ventilation that were understood more or less in the past and to call attention to some danger in connection with present-day trends or practices.

Jan 1, 1939

By Robert A. Field

Static-Load Piledriving utilizes a hydraulic push to facilitate the installation of a pile. The pile is not rotated, impacted or vibrated. A smooth pushing force advances the pile incrementally into the ground. Static-Load devices must have a reaction mass to push against. The most simple form of a Static-Load device is a jack; more advanced equipment, such as the Still Worker, also utilizes this approach. This paper focuses on the use of the Still Worker on three challenging projects. In each case, the existing site conditions made it risky, or unattractive, to utilize conventional impact, vibratory, or drilled-shaft equipment.

Jan 1, 1997

By M. Kolahdoozan, H. Noori

"Molybdenite flotation at the Sarcheshmeh Copper Complex has been studied as a function of pulp potential controlled using two types of sodium sulfide (mineral and chemical origin). Air and either plant or laboratory nitrogen was used as a flotation carrier. Potential measurements were taken in the rougher cells as it was proved to be vital for molybdenite flotation. Flotation test with reducing potentials between -525 and -575 mv gave the highest molybdenum recovery (93%) and the lowest copper recovery of between 4 to 15% can be achieved. These potentials did not change considerably by adding increasing amounts of sodium sulfide. At more oxidizing potentials, i.e. more than -450 mv, the recovery of copper increases while the recovery of Molybdenite drops.INTRODUCTIONThe average copper ore feed grade to the Sarcheshmeh flotation circuit is typically set at about 1.2% Cu. to be delivered to processing unit is set at 1.2%. There is no control of molybdenum (Mo) which usually varies between 0.01 and 0.04%. During concentration, a Cu-Mo concentrate is produced by one stage of roughing, one stage of scavenging and two stages of cleaning. Final concentrate contains 0.5% of Mo and 32% of Cu while the particle size is 90% under 42 microns (325 mesh). Because of the high grade of Mo in this concentrate and economic interests, a molybdenite flotation circuit plant was built in 1984. This plant was designed to treat 1432 tons of Cu-Mo concentrate (on dry basis) and consists of one stage of roughing followed by seven stages of cleaning. After dewatering the concentrate contains 53.7% Mo which is dried and shipped overseas.The majority of molybdenite production worldwide comes as byproduct of copper porphyry ores. The Mo grade typically varies between 0.01 and 0.06% and accompanies chalcopyrite and chalcocite. Due to the hydrophobic nature of molybdenite, it can be floated along with copper sulfides. Thus the overall concentrate of Cu and Mo contains 0.2-1% of molybdenum as well as 20-42% of copper. To separate the Mo, Cu and Fe minerals, depressants are used. The most important of which are sodium sulfide, sodium hydrosulfide, Anomal D, sodium cyanide, ferropottasium and ferro-cyanide. The first three regeants have been extensively used for successfully treating porphyry ores [1]. In the molybdenum plant of the Sarcheshmeh Copper Complex only sodium sulfide has been used to date."

Jan 1, 2006

A research project was commissioned by the Australian Coal Association Research Program (ACARP) to improve the understanding of tailgate strata mechanics and to provide a more rigorous engineering basis for tailgate support design. A deformation mechanism termed æskew roofÆ was defined which relates the regional influence of differential horizontal strata movement (shear) about longwall extraction to gateroads. Confirmation of the mechanism was achieved by field investigations which included measurement of the shear displacement along weak interfaces. Under geological and mining conditions where the skew roof mechanism operated, strata units were found to move progressively further towards the goaf with height into the roof. 3D numerical modelling was used to assess the major geotechnical factors controlling the mechanism and to determine appropriate support strategies within a æskew roofÆ environment including the role of cables versus standing supports. The skew mechanism is considered relevant to; all roadways in the vicinity of longwall extraction including the faceline itself, chain pillar design, and support design.

Jan 1, 2005

By D. P. Venter

When Oryx Mine down-scaled in 1994, focus was placed on development, with the primary aim being the exposure and proving of ore reserves. In order to achieve this aim, development ends had to be advanced to reef at the maximum possible rate. This in turn called for support methods which could keep up with the advancing faces, taking up minimum space and time for installation, while providing on the face a real coverage and effective long-term support. In the majority of the development ends which were located in fairly competent ground, the grouted rod development support proved to be adequate until such time as secondary support in the form of meshing and lacing could be installed. The ends developing towards the eastern boundary of the mine, especially in the ?C? block, encountered extremely adverse ground conditions due to the presence of smectite zones within the footwall quartzites. Smectites are a group of montmorillonite clay materials, mainly composed of hydrous aluminosilicates. They occur as minute platy crystals in the rock mass and are especially notable for their ability to absorb liquids. Generally, the zones are found in between the bedding planes of the host rock, and may vary considerably in thickness over short distances. Wherever the smectites were exposed by the development blasting, the rockwalls weathered as the smectites absorbed water and the condition of the tunnel rockwalls deteriorated rapidly. When the smectites were left exposed and allowed to weather, it became almost impossible to install secondary permanent support such as meshing and lacing at a later stage. To minimise the exposure time and subsequent deterioration of the smectite zones, it was recommended that all development ends encountering smectites be shotcreted as soon as possible after blasting. In developing a shotcreting support methodology, both a drycreting and wetcreting system were investigated. The situation at the time ruled out the use of a wetcreting system on the basis of the extensive and costly infrastructure required, as well as its limited manoeuverability. Instead, it was decided to opt for as maller scale but more manoeuverable drycreting system. The system utilized a number of portable drycrete machines with pre-bagged cement, which could support several development ends in close proximity. Initial trials using normal 30 MPa shotcrete on 19level proved successful and the system was implemented.

Jan 1, 1998

By Donald J. Barnes

There are no producing or developing mines in the study area. The only mineral production was stone from a basalt deposit near Indian View Point. Cinders and sand and gravel have been produced from deposits within 1/2 mi (0.8 km) of the boundary. Stone, sand and gravel, and cinder deposits inside the area are not considered resources because equal or better quality material is found closer to markets. The study area has no known oil and gas, coal, geothermal, or other energy related deposits. However, in 1982 application was filed on 25,000 acres (10,125 ha) of petroleum and on 15,000 acres; (6,0/5 ha) of geothermal leases.

Jan 1, 1983

By Mehmet Canbazoglu, Kaarlo Haavanlammi, Hannu Laitala

Cobalt is currently a critical metal because of the increasing number of electrical vehicles forecast for production. Copper and zinc are base metals that are used in many everyday applications, including vehicle production. Eti Bakir Co. Mazidagi Phosphate Plants in the Mazidagi district of Mardin, Turkey is a multi-product facility that produces cobalt, copper, and zinc, as well as fertilizers, from the roaster calcine. Roaster off gas is treated in a sulfuric acid plant (SAP) and the acid itself is utilized in fertilizer production. The comminution circuit, roaster, SAP, and calcine leaching process were developed by Outotec and integrated with the fertilizer production process implemented by Eti Bakir A.Ş. This paper describes the hydrometallurgical calcine leaching process used at the plant, with a focus on the oxidative pressure leaching of the cobalt, zinc, and copper-containing calcine. The cold and hot commissioning phases of the pressure leaching autoclave start-up are discussed together with experiences from the ramp-up period. The production processes of the copper cathode and cobalt and zinc-containing salts are also presented together with some of the plant’s operating parameters. INTRODUCTION The ETI Bakir A.S. fertilizer plant, Turkey, is located in Mardin Province near the border with Syria, (Figure 1). The leaching plant project was started in 2012. The purpose of the plant is to separate the valuable metals from the calcine produced by the pyrite roasters, which are used to produce a SO2 containing gas for the new sulfuric acid plant. Fertilizer production requires sulfuric acid, and for this reason a sulfuric acid plant was built; customer already had access to pyrite concentrate, which is used as the roaster feed. During the engineering phase of the roaster and acid plants it was noticed that the roasted calcine contained considerable amounts of valuable metals like cobalt, copper, and zinc. To recover these metals, a calcine leaching process was developed at the Outotec Research Center in Pori, Finland. The main process connections of the Mazidagi site are shown in Figure 2.

Jan 1, 2019

The strippable reserves of bituminous coal and lignite in the United States were calculated in accordance with the prevailing conditions of seam thickness and depth of overburden in each of the several coal-producing areas of the Nation. Within defined limits of seam thickness and depth of overburden, it is estimated that there was a remaining strippable resource of 118 billion tons of raw bituminous coal and lignite as of January 1, 1968. Because of topography, natural and manmade features, and other limitations, only 45 billion tons of the resource are strippable reserves. Of this, 32 billion tons is considered low-sulfur (less than 1 percent), 4 billion tons is medium-sulfur (1 to 2 percent), and 9 billion tons is high-sulfur (over 2 percent) coal. Owing to a cleaning loss affecting that portion of strip coal that is mechanically cleaned, the 45 billion tons of strippable reserves are reduced to 39.6 billion tons of marketable coal. A brief discussion is given for each coal-producing State, summarizing past and present production, historical background, and outlook. Appendix A contains reserve data by State, county, seam, and sulfur content. Appendix B contains the general information and requirements necessary to comply with the current strip mining laws covering 20 States.

Jan 1, 1971

By Mary Cocklan-Vendl

Regulatory processes associated with development of a world class lead-zinc mine, Red Dog Mine, in northwestern Alaska were reviewed and evaluated. Informal interviews with key project personnel, consultants, and agency field and permitting specialists provided perspective on the regulatory successes and failures of the project. Due to potential impacts to air quality, water quality, wetlands, and National Park lands, an Environmental Impact Statement was required. By developing a comprehensive baseline of information on the existing environment to aid in minimizing impacts during project siting/design and through regular coordination of evolving project plans with regulatory agencies, the mine developers were able to acquire necessary permits in a timely and cost effective manner. The only major exceptions occurred when inadequate information was collected on dispersal of airborne particulates, rates of surface water run-off, and groundwater quality. These deficiencies resulted in the need for design changes, unscheduled construction, additional environmental monitoring costs, and delays in issuance of the NPDES permit.

Jan 1, 1992

By James S. Browning

The Mineral Resources Institute and State Mine Experiment Station of the University of Alabama conducted Humphreys spiral tests on fine coal waste from nine preparation plants of Alabama strip mining operations to determine the feasibility of recovering low ash and sulfur fuel meeting steam coal specifications. The ash in the samples ranged from 9 - 5l%, and the total sulfur ranged from 0.4J- 2.39%. Continuous laboratory tests using a Humphreys spiral gave good recovery of the coal with excellent rejection of the ash and pyritic sulfur. Coal recoveries of 83.6 - 94.1% were achieved from the different samples. Ash content of the clean coal products fell within a range of 5 - 12.2%, with a total sulfur content of 0.62 and 1.10%. In quality, the products were comparable or superior to those now being shipped from the preparation plants.

Jan 1, 1980

By P. J. Williams, A. R. Foster

Petrographic studies, assay records, and laser ablation-inductively coupled plasma-mass spectrometer (LA-ICP-MS) analyses of major sulfides suggest nearly all of the gold at the Ernest Henry Cu-Au deposit occurs in the form of native gold or electrum (95-65 wt.% Au); sylvanite and dissolved gold in cobaltite, chalcopyrite, and pyrite make only minor contributions. LA-ICP-MS analyses of the gold contents of chalcopyrite gave from 8 to 139 ppb (mean = 56 ppb), more than an order of magnitude lower than those experimentally determined in chalcopyrite in equilibrium with native gold at the estimated mineralization temperatures (350°-450°C). Gold content is more variable in pyrite (1-400 ppb, mean = 77 ppb) and highest in narrow growth zones of a subordinate type of complexly zoned pyrite wherein it is associated with elevated As, Ag, Sn, Sb, Te, and Bi. Deposition of gold-electrum was closely associated with, but preceded some of the chalcopyrite deposition, as indicated by microtextures and lower bulk Au:Cu ratios in late-stage chalcopyrite-rich veins. Gold grains have maximum dimensions from <1 to 50 micrometers, and are heterogeneously distributed with most occurring in microscale clusters. Fifty-five out of 76 grains recorded in polished sections are in contact with both chalcopyrite and pyrite, and many of the rest are in sites where such a relationship could exist in the third dimension. The dominant textural sites are intergrowths with chalcopyrite in microveinlets cutting pyrite, and on faces of pyrite grains in contact with chalcopyrite. Scanning electron microscopy, electron microprobe analysis, and proton induced X-ray emission studies show that pyrite associated with gold includes complexly zoned, weakly zoned, arsenian, and arsenic-poor types. The textures are compatible with the possibility that most gold was deposited electrochemically as native metal on pyrite surfaces. The textural distribution of gold has important metallurgical implications given that the ore processing circuits at Ernest Henry and most other sulfide copper mines are designed to exclude pyrite (and arsenic) from concentrates.

Jan 1, 2007

By AIME AIME

THE following Officers, Directors, and guests were present: Herbert Hoover, A. R. Ledoux, Henry S. Drinker, Edwin Ludlow, Samuel A. Taylor, Charles F: Rand, William M. Corse, Arthur S.. Dwight, Glen H. Clevenger, L. W. Francis, F. G. Cottrell, Bradley Stoughton, Percy E. Barbour, E. P. Mathewson, Dorsey A. Lyon, Archibald Douglas, A. D. Flinn, RobertLinton, James F. Kemp, William Y. Westervelt, J. W. Richards, W. L. Saunders, George Otis Smith, Thomas T. Read, J..C. Murray, Ralph Arnold. A Committee on Mine Equipment was appointed composed as follows: Graham Bright, chairman, William Kelly, Howard N. Eavenson, R. E. Hobart, and S. P. Rumsey. B. D. Saklatwalla was added to the Committee on Miscellaneous Metals and W. Spencer Hutchinson was added to the Committee on Mining Geology. A revised budget for 1921 was approved. A petition duly signed to amend Section 1., of Article III of the Constitution, increasing the initiation fees from ten dollars to twenty dollars, was approved by the Board.

Jan 1, 1920

The contract objective was to evaluate sources of airborne quartz and research control methods that would assist underground mine operators in complying with respirable dust standards which have been reduced because of quartz in the dust exceeding five percent. The work involved: Phase I -evaluate sources of quartz dust at the roof bolter work location; Phase II -evaluate the relationship between the quartz content of the coal and adjoining rock strata and quartz exposure at the roof bolter and continuous miner locations Phase III -conduct laboratory tests to determine performance parameters for roof bolter dust collector systems. The underground surveys for Phases I and II determined: (1) the continuous miner typically is the greatest source of quartz exposure for the miner and roof bolter operators when single-split ventilation is utilized, (2) a statistically significant relationship be­tween quartz content in face material and operator exposure was not determined and data suggested mining equipment and procedures may be more critical. The Phase III lab tests indicated the use of dust hog-type bits, filter cartridges, maximized collector airflow, and reduced bit rpm should be utilized to minimize dust liberation at the roof bolter.

Jan 1, 1985

By O. Q. Leone

Excellent metal quality, with lower power requirement, is attained in electrorefining titanium by using internal heating of the fused-salt bath. An internal heater provides more effective heat utilization, simplifies structural components in cell design, and prolongs cell life by eliminating direct application of heat to the cell container. This Bureau of Mines report covers one phase of the research in progress at the Electrometallurgical Experiment Station at Boulder City, Nev., for improving the techniques and lowering the total power requirement for electro-refining titanium metal.

Jan 1, 1959

By W. A. Backofen, G. Y. Chin, W. F. Hosford

The ductile fracturing process was studied in single-crystal and poly cvystalline aluminum deformed in tension over a temperature range from 295° to 4.2°K. At temperatures as low as 77°K, the fracture of "inclusion-free" material, including zone-refined aluminum, was by rupture (-100 pct RA). At 4.2 OK, fracture was brought on by adia-batic shear. Metallographic examination did not disclose any voids or slip-band microcracks, thus negating for inherently ductile metals any mechanism of void nucleation by vacancy condensation or of cracking due to dislocation pile-ups. In Izigh-purity aluminum not treated to be inclusion-free, fracture at temperatures as low as 45°K was of the double-cup type and a result of void formation. The reduction-of-area decreased as temperature was lowered, corresponding to the earlier appearance of voids. Such behavior was rationalized in terms of a larger increase, with decreasing temperature, in the .flow stress relative to the strength of the inclusion-matrix interface. Evidence for low-temperature adiabatic shear was found in discontinuous flow at 4.2"K, in the transition to a localized shear fracture at low temperatures, and in the suppression of shear fracture with an elastically hard pulling device. A simple analysis for the initiation of adiabatic shew permitted a general correlation of the various contributing factors. It has been pointed out that the duration of shear depends upon effective mass and elastic stiffness of the deformation system. IT has long been recognized that fracture* may Throughout this paper, the term "fracture" is taken to mean any process that results in the separation of a material into two (or more) parts. Thus rupture as it may be encountered in a tension test leading to 100 pct reduction-of-area is included in this category. occur in a ductile mode, and that the process can be of great practical as well as general interest. Much information about ductile fracture has also been accumulated over this period, but only recently has an understanding of mechanism begun to appear. Ludwik,&apos; in 1926, first reported fracture in a tensile specimen starting with a central crack in the necked section. Since then, other studies have disclosed that such cracks may form by the coalescence of voids nucleated in this region where hydrostatic tension is highest.2-4 Rogers and Crussard et al.&apos; have emphasized void formation and reori-entation along localized shear bands as a mode of crack propagation. pines6 has considered the tensile rod as a bundle of fibers joined by weak interfaces, which subsequently separate to allow individual fiber contraction. The notion of cavity growth and coalescence by purely plastic processes was discussed by Cottrell: who added that the tensile reduction-of-area ought not to be sensitive to temperature. On the other hand, it has been observed that the reduction-of-area is greatly increased if tests are carried out at high temperaturesa or under high hydrostatic pressure.&apos; Fracturing anisotropy in wrought products lends support to the idea of void formation from preexisting flaws strongly aligned by earlier processing.&apos;&apos;-l2 There is evidence that many voids result from the fracturing of inclusions or separation at the inclusion-matrix interface Another possibility is that voids grow out of pore volume produced in the initial solidification and never fully removed in later working. In general, a structure 3f particles, pores, and weak interfaces can be expected, at least in materials of engineering interest. Vacancy condensation has been suggested as an alternative mechanism of void formation for materials considered to be inclusion-free.13 Yet experience has shown that tensile reduction-of-area increases with purity, to the extreme of rupture as so often observed in single crystals. Adiabatic shear has an important bearing on ductile fracture. It occurs when the decrease of flow stress, as a result of local temperature rise from heat generated during straining, becomes larger than the increase due to strain and strain-rate hardening. As demonstrated by experiments on punching of plates,14 a large temperature rise may be brought about by rapid straining. Adiabatic flow as a result of the high strain rate reached in an ordinary tensile specimen just prior to separation may account for the cone formation in cup-and-cone fracture;14 evidence of such local heating has been presented.15 For geometrical reasons, however, pure sliding along the conical surfaces is unlikely, and separation under tensile forces is probably an important accompanying feature of the shear.7 In deformation processing operations, a high shear-strain rate may exist at boundaries between plas-

Jan 1, 1964

Gullies are the vital in-stope excavations that provide access for mining personnel and material to, and mined ore from, the producing faces in the tabular hard rock mines. They pose a serious problem in most mines because they induce stress orientations, which, combined with blast damage, produce adverse rock fracture patterns that contribute to the loss of hangingwall and sidewall integrity. Rock-related injury statistics confirm this by highlighting gullies as the second-highest risk area in South African hard rock mines. Inappropriate gully geometries, poor blasting practice, and non-adherence to accepted standards worsen the problem. The aim of this work is, firstly, to provide guidelines to select the correct gully geometry and appropriate support for a particular geotechnical environment and, secondly, to review the practical issues behind gully safety and stability. In order to meet these aims, this paper reviews the available literature on gullies and their history, and reports on an industry-wide survey of practices and opinions. Then it covers observations from underground visits to 107 gullies situated in the respective geotechnical environments of the Basal Reef, Beatrix Reef, Vaal Reef, Carbon Leader Reef, Ventersdorp Contact Reef, Kimberley Reef, Kalkoenkrans Reef, Merensky Reef, and UG2 Reef. Despite the differing geotechnical conditions and gully geometries, common problems are experienced with geological structure, stress, and fracturing. Results from numerical modelling are also presented to help analyse the underground observations and to quantify the merits of the different gully layouts. It is concluded that there are no new techniques available to improve gully stability, but that significant improvements in safety are attainable by employing the correct gully geometry for the geotechnical environment, good blasting practice, and appropriate support.

Jan 1, 2002

By John Chipman

THE equilibrium between titanium in liquid iron and titanium oxides has been studied by Hadley and Derge.&apos; They have shown that a minimum occurs in the oxygen content of the metal between 0.1 and 1.0 pct Ti, but its exact level was not fixed. The oxide phase in this minimum range was principally TiO, containing some iron oxide. On the other hand, for concentrations above 5 pct Ti the oxide phase was TiO and the oxygen content of the metal increased rapidly with increasing titanium content. From their observations and the free energy of Ti0 and TiOz reported by Kelley and ah,&apos; it is possible to derive approximate values for the activity coefficients of titanium and oxygen in liquid iron-titanium alloys and the conditions for equilibrium in steel deoxidation. Neglecting possible departures from the stoichio-metric composition, the condition of equilibrium with Ti0 may be expressed as follows: TiO= Ti_ + C) log K = log NTl + log [% O] + log yTi + log fQ Here as a matter of convenience the titanium concentration is expressed in mol fraction while that of oxygen is in weight percent. The activity coefficients are yTi and fo. The value of log fo approaches zero as the concentration of titanium approaches zero, while that of log yTi approaches a limiting value of In Fig. 1 the sum of log NTi + log [% 0] is plotted for mol fractions of titanium between 0.05 and 0.50. The smooth extrapolation gives a value of —4.15 which corresponds to log K — log y:i . We therefore have the equation: According to the data of Kelley and Mah,&apos; the free energy of formation of Ti0 at 1900°K is -82,400 cal. The free energy of solution of half a mol of oxygen in iron, taking 1 pct 0 as the standard state, is -29,300 cal. From these we write: From these equations the activity coefficient of titanium at infinite dilution in iron is found to have a value of 0.011 or log y°. = -1.96. This is only an approximate value but is certainly better than the estimated 0.05 in Basic Open Hearth Steelmaking To obtain approximate values for the activity coefficient at intermediate concentrations, it is as- sumed that log yTi(l is constant and equal to -1.96. This corresponds to a value of E;: = 3 In yTi/aNTi = 9.0 which is not unreasonable We now have the value for the activity of titanium and the percentage of oxygen in equilibrium with TiO. It is therefore a simple matter to calculate the activity coefficient of oxygen which is shown in Fig. 2. The effect of titanium is rather large, being comparable to that of vanadium, but not so large as has been reported for aluminum. The slope of the line at low concentrations corresponds to E: = aln yo/ aNTi=-0.37. At concentrations below 1 pct Ti the deoxidation constant and oxygen content for equilibrium with TiO, can be calculated from the foregoing data and the free energy of formation of TiO,, which according to Kelley and Mah is -144,600 cal at 1900°K. The free energy of solution of oxygen has been given; that of Ti to form a dilute solution with 1 pct Ti as the standard state is RT ln (0.5585 y:i/47.9) = -34,800 cal. From these data we find (for concentrations in wt pct): TiO, = Ti + 2 -0; hFTgO0= + 51,200 cal log if =-5.89 The interaction coefficients, concentrations being expressed as wt pct, are e;: = alogfTi/a[% Ti] = +0.048 and e:&apos; = a logfo,/a[ojTi] = -0.187. The calculation gives the following results which, in view of the impurity of the oxide phase, must be regarded as approximate:

Jan 1, 1961

By J. N. Van der Merwe

The research described in the paper was aimed at providing standardized information of cases of failed and intact coal pillars in the form of databases to researchers. It also offered the opportunity to take stock of the pillar stability situation in coalmining and to review the impact of the application of the safety factor formula for pillar design. It was found that the physical parameters of coalmining have not changed substantially over the last four decades. However, changes in the controllable parameters like pillar width, pillar width-to-height ratio and percentage extraction have all moved toward the more conservative side. Scrutiny of the database indicates that of all the failures recorded, only 23 occurred in panels that were mined after 1969, when one can assume that the safety factor formula was fully applied. If the pre-1969 practices had been continued, at least 144 collapses would have been expected. There has thus been a substantial reduction of pillar collapse cases, justifying the cost paid for the formula, which has shown to be in the region of 600 million tons of coal. It is evident that that are distinct differences in the natures of the failures among different coalfields. This justifies the attempts to derive seam or coal field specific strength formulae and is a topic that should be pursued.

Jan 1, 2006

By P. W. Jensen

Gold deposits in Interior Alaska are commonly coincident in time and space with reduced, mid-Cretaceous granitoids. The True North deposit of the Fairbanks district is several km from such granitoids, but yields mineralization ages indistinguishable from the Fort Knox granite-hosted deposit. True North, however, resembles sediment-hosted epithermal Au, demonstrating the variability of intrusion-related Au deposits in metamorphic rocks. The True North deposit (14M tons at 1.5 gpt) is hosted within a carbonaceous thrust complex separating eclogite facies from amphibolite facies rocks, located > 5 km from mineralized granite outcrops. The ores contain anomalous Sb, As, and Hg (stibnite is the most common sulfide) with ankerite-sericite alteration in steep NE-striking ?feeder? shears and low angle thrust shears. Nearest hornfelsed rocks are located > 1 km away, and across several high-angle faults. Fluid inclusion data indicates trapping temperatures of ~250C from low-density, low-salinity fluids at P < 0.5 kb. Au was originally present as solid solution in sulfides; minable ores are restricted to the oxidized upper 100 m of the deposit. The considerable differences between this deposit and the temporally equivalent Fort Knox intrusion-hosted deposit indicate no one description adequately characterizes this deposit type.

May 1, 2003

By A. Pellegrino, F. Collin, C. Guiducci, R. Charlier

A numerical approach for modeling coupled Hydro-Mechanical fracture behavior in 2D is presented in this paper. This approach accounts for the strong dependence of the flow characteristics on fracture apertures and offers an anisotropic description of the flow propagation in the fracture. An interface finite element and a constitutive model are developed . In order to validate the applicability of the model to general geomechanic problems, 2D simulations were performed. Results show the good application of the mathematical model and the fundamental hydraulic role played by the fractures. In diesem Beitrag wird ein Stoffgesetz vorgeschlagen um hydromechanisches Kluftverhalten numerisch zu Modellieren. Dieser Vorgang nimmt die starke Abhängigkeit der Fliesseigenschaften von der Kluftöffnung mit in Anbetracht. Ein Interfaceelement und ein Stoffgesetz wurden entwickelt. Zum validieren der Anwendbarkeit dieses Modells wurden 2D Simulationen durchgeführt. Ergebnisse haben gezeigt dass das mathematische Model anwendbar ist und dass Klüfte eine fundamentale hydraulische Rolle spielen. Une approche numérique pour la modélisation du comportement couplé hydro-mécanique des fractures en 2D est présentée dans ce papier. Cette approche prend en compte la forte dépendance des caractéristiques du flux de fluide sur les ouvertures des fractures et présente une description anisotrope de la propagation du flux dans la fracture. Un élément fini d&apos;interface et un modèle constitutif sont développés. Dans le but de valider l&apos;applicabilité du modèle à des problèmes généraux de géomécanique, des simulations 2D ont été réalisées. Les résultats montrent la bonne application du modèle mathématique et le rôle hydraulique fondamental joué par les fractures.

Jan 1, 2003