Search Documents

"SUMMARYThe K.M.A. reservoir was discovered to be oil bearing at a depth of 3,719 feet on March 11, 1931. Extensive development, however, was not begun immediately, because the discovery well had a low initial daily oil production, and market conditions for oil were unfavorable. Development of the field progressed slowly for the next 6 1/2 years. In the latter part of 1937, a wildcat well approximately 2 miles southwest of the discovery well was drilled on a magnetometer high and completed with an initial flowing production of 2,016 barrels of 43° A.P.I.-gravity oil in 12 hours. Rapid development of the southwestern part of the K.M.A. field was begun immediately and continued until over 700 wells were drilled and approximately 12,500 acres proved oil productive.Because of the large size of the entire K.M.A. field, this report is limited in scope to the southwestern part only, and the discussion that follows pertains to this area only. The closing date for production statistics is August 1, 1949.The K.M.A. structure is a complex anticline having a maximum closure of 250 feet, and the K.M.A. formation is composed of sediments that grade from limestone through sandy lime and limy sand to sandstone with thin streaks of shale. Two distinct members of the K.M.A. formation, zone I and zone II, are oil productive. Core analyses indicate the average porosity to be 16.5 percent for zone I and 16.1 percent for zone II. A relationship was established from core data, which showed the correlative permeabilities to be 42.1 millidarcys for zone I and 39.5 millidarcys for zone II, whereas the arithmetical averages of the permeabilities were 84 millidarcys for zone I and 216 millidarcys for zone II. Connate water saturations were 17.5 percent for zone I and 20.0 percent for zone II. The porosity-saturation method, using a thickness-correction factor, was employed to calculate the volume c 168.1 million barrels of stock-tank oil initially in place in the reservoir. Analyses of the reservoir oilIn that, although the initial reservoir pressure was 1,750 p.s.i., the original reservoir oil was saturated to only 1,300 at which pressure 1 barrel of stock,tank oil contained 525 cubic feet of gas in solution.A serious decline in reservoir pressure during the 2 years of rapid development alarmed the operators and caused them to consider a cooperative pressure-maintenance program. In the latter part of 1939, the K.M.A. Pressure Maintenance Association was organized, and the gasoline plants in the field agreed to process the wet gas and return the dry gas to leases having gas-injection wells. Approximately 27 percent of the cumulative volume of produced gas had been returned to the reservoir by August 1, 1949."

Jun 1, 1952

By Jack Eloranta

The winning of metals often requires fine grinding of very hard ore. The US Bureau of mines measured compressive strengths exceeding 100,000 PSI (700 MPa) in Minnesota taconites. Grinding down to 300 mesh (50 µ) is required for some fine-grained taconites. While other metal ores may not be as strong, significant grinding costs are the rule rather than the exception. One author recently reported that a 7% drop in grinding costs would fully offset a doubling of the drill and blast budget. Another author found that drill and blast costs were 13% of the costs of producing iron ore concentrate while fine crushing and grinding were over 60% of the cost of producing concentrate.

Jan 1, 2013

By Alexander Garcia

Roof and rib falls are the basic ground control hazards associated with underground roadways during development, stand up and, if applicable, retreat. Falls of ground can happen following the deterioration of supports or rock conditions over time, and particularly as a consequence of continuing rock deformation and/ or failure to install adequate support. Once developed, the risk of a failure is increased due to the effects of time as well as to front abutment stresses through retreat mining. The measurement of strata displacement using monitoring equipment is a form of ground control risk assessment. These monitoring systems are active, or ?live?, in a sense that risk is assessed real-time. However, there are circumstances in which falls of ground can occur without the prior recording of excessive movement. In addition, monitoring equipment is typically placed at set intervals, and strata conditions could vary between these points. Consequently, a visual assessment of other factors contributing to the risk of a fall should be made in order to complete a ground control risk assessment. Such surveys are usually one-off, thus capturing roadway conditions at one particular point in time. Ongoing deterioration is not documented through such one-time surveys, and there is a requirement for real-time or live assessment where a system is in place so that observation data can be updated on an ongoing basis, and a useful summary of prevailing roadway states produced on demand. To address the shortfalls of one-time assessments, a ?live? computerbased quantitative ground control risk assessment process has been developed. It combines visual observations processed in a quantitative manner with existing monitoring data into an interpretable output which indicates zones of roadway where there is an increased risk of a fall of ground from the roof or sides, so that remedial action can be carried out to mitigate that risk. Through improved procedures, it is now possible to generate a ground control risk assessment for each roadway, and one which can be updated frequently. This paper aims to outline and describe the assessment process.

Jan 1, 2012

By Wayne L. Worrell

Thermodynamic data for the stable carbides and oxides of chromium, molybdenum, and tungsten have been critically eualuuted and are used to determine the stable condensed phases at 1 atm total pressure in each metal-carbon-oxygen system. Pourbaix-Ellingham diagrams have been constructed and are used to estimate the minimum temperatures neces.see)*y to oblain these metals by corbolhermic redlrction under reduced pressures. USING recently reported data for the carbides and oxides of chromium, molybdenum, and tungsten, the stable phases in the Group VI metal-carbon-oxygen systems at specific temperatures and pressures can be determined. The thermodynamically stable regions in each metal-carbon-oxygen system can be completely pictured using a Pourbaix-Ellingham diagram in which the two coordinates are oxygen potential (-RT In Po2) and temperature. Worrell and chipman' have described and constructed such diagrams for the metal-carbon-oxygen systems of vanadium, columbium, and tantalum. Downing2 has used similar diagrams to provide a description of the reactions in submerged arc furnaces. One of the examples which he cited was the Cr-C-O system; however, an improved diagram is presented in this paper using recently obtained data for the carbides of chromium. Although some of the oxides and carbides of the Group VI metals exist over slight ranges of composition,3 all solid phases are represented as stoi-chiometric compounds in the subsequent diagrams. Any error introduced into the calculated equilibria by neglecting the compositional variation of these phases is less than the uncertainty in the thermodynamic data. In a Pourbaix-Ellingham diagram for a three-component system, the phase rule requires that at equilibrium four condensed phases specify a point, three condensed phases determine a line, and two condensed phases define an area. To obtain a well-defined area at high oxygen potentials and teniperatures, the initial carbon to oxygen mole ratio is specified to be more than sufficient to reduce the oxide but not enough to convert all the metal to carbide. Thus, the lowest regions in the subse- quent Pourbaix-Ellingham diagrams represent areas in which the metal and its carbide are the stable condensed phases. Cr-C-O SYSTEM A) Thermodynamic Data. To simplify the subsequent calculations, all thermodynamic data are presented in the form of linear Gibbs-energy-of-formation* equations which were derived for the temperature range 505° to 2000°K and are reasonably accurate over the entire temperature ranges of the diagrams. The thermodynamic data for the compounds occurring in the Cr-C-O system are summarized in Table I. Several volatile chromium oxides have been reported,4 but their influence is negligible in the Cr-C-O system. Thermodynamic data for CO and CO2 were taken from the compilation of Coughlin.5 The only solid chromium oxide sufficiently stable to exist below 1800°K in the Cr-C-O system is Cr2Os.11 The Gibbs-energy-of-formation equation for Cr2O3 was obtained by revising the data tabulated in Coughlin,5 using the heat of formation of ah' and the high-temperature thermal data for chromium.7 In 1953 Richardson8 re-evaluated the original work of Kelley and coworkers,9 who measured the thermodynamic properties of the chromium carbides. However, the high-temperature equilibrium results of Boericke9 yield values for ?G°f of Cr2O3 which are 2 kcal more positive than the accepted data. His results for the chromium carbides are based on the same questionable equilibria. Gleiser10 recently determined the Gibbs energy of formation of Cr3C2 and the equation in Table I was calculated from her data and the thermal data of Kelley and coworkers.9 Thermodynamic data for the Cr7C3 and Cr23C6 carbides were obtained by combining the Cr3C2 data

Jan 1, 1965

By B Hannah, M Uriarte, F Labarca, C Madore, G Ganapathi, L Martin, T Haase

BechtelÆs Mining and Metals projects across the globe are executed in remote arid and semi-arid countries where providing even basic water supplies impose considerable challenges. Opportunities for water conservation measures using a Six Sigma initiative were proactively pursued to address the potential business impacts of limited availability of water resources. The initiative investigated areas driving water-optimisation during concrete operations and camp management. This paper details the water conservation evaluation of alternatives and cost/benefit analysis based on current and predicted water usage for development projects. Optimisation of water consumption through institutionalising more prescriptive standards for camp design and defining water conservation requirements have resulted in a new standard specification. Based on our projected mining project workload across the globe, it is estimated that for the period 2012 - 2015, a potential 5.5 M m3 water savings resulting in US$11 M could be realised for construction camps and savings of 4 M m3 of peripheral concrete process water resulting in potential cost savings of US$8 M could be achieved as a result of these revised standards.CITATION:Haase, T, Hannah, B, Ganapathi, G, Martin, L, Madore, C, Labarca, F and Uriarte, M, 2013. Water conservation at construction projects, in Proceedings Water in Mining 2013 , pp 251-258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By W. A. Burns

Vertical flow is an important mechanism in many petroleum reservoirs. Yet no adequate method has heretofore been proposed for determining the in-situ vertical permeability in a reasonable length of time. Core measurements of vertical permeability do not necessarily represent effective in-situ values. Cores may be representative of only localized pockets of high or low permeability, and total reliance on cores might cause one to overlook the presence of vertical fractures altogether. Conventional single-well tests, interference tests, and pulse tests commonly are used to determine horizontal transmissibility, khh/u, but generally are not designed to measure vertical trans-missibility or other groups containing vertical permeability, ku. A new well test described here provides a measure of in-situ vertical permeability as well as the previously measurable horizontal permeability. This "vertical test" determines the vertical diffusivity, kv/gcu, and horizontal transmissibility, khd1/u (where dl is the length of injection or production perforations). The test is basically a short-term interference or pulse test normally lasting less than a day. Conventional down-hole equipment is used between two isolated sets of perforations in the same well, as shown in Fig. 1. A "layer-cake" description of a reservoir can be obtained by running two or more vertical tests in the same well, each over different vertical intervals. Each test can be analyzed for the effective vertical and horizontal properties of the interval tested. In addition, a vertical well test can determine the effective- ness of a shale barrier or tight zone by testing across it. Field use to date of vertical testing has confirmed its utility in reservoir description. Mathematical Basis Interpretation of vertical tests for ku and kh is based on comparison of measured pressure response with computer-generated response. Pressure behavior during a vertical test in a homogeneous, anisotropic, infinite-acting reservoir (infinite in radial extent and bounded in both directions vertically) is given by the diffusion equation for slightly compressible fluids with negligible gravity effects.l A schematic diagram of the problem is presented in Fig. 2, and an analytic solution, based on the image

Jan 1, 1970

By Robert M. Matyas, P. E. Sperry, Robert J. Smith, A. A. Mathews

INTRODUCTION The first Dispute Review Board (DRB) was utilized on a tunnel project 20 years ago. Increasingly utilized on a wide range of construction projects, DRB's are becoming the norm on tunnel and underground projects. This paper summarizes the growth in this usage, uses observations and experience to establish that barriers to the utilization of DRB's are more perceived than real and that many arguments against the DRB concept are not valid, and notes some of the salient elements that should be considered in practice to optimize DRB effectiveness. The purpose of the paper is to provide an annotated checklist for current and prospective users. The basic concept, structure, and operation of DRB's are described elsewhere and will not be repeated here (ASCE, 1991). DISPUTE REVIEW BOARD USAGE A compilation of Dispute Review Board usage for tunnel and underground projects to January 1994 indicated use on 63 contracts with a cumulative construction value of $3.8 billion and a total of 60 disputes settled. As of that same date, DRB's were planned for another 63 contracts with an estimated construction value of $4.7 billion. (A listing of these 126 projects is available from the authors.) This success and popularity have spread to other civil projects as well as process and building construction. The increase in DRB usage has been exponential. See Figure 1.

Jan 1, 1995

By T. Rasmussen, T. G. Jørgensen, T. Fischer, R. K. McLimans, C. Knudsen, D. Frei

Ilmenite-bearing paleo-beach deposits were discovered in Jylland, Denmark using a combination of Ground Penetrating Radar (GPR), portable X-ray fluorescence (XMET), bulk XRF analyses, Computer Controlled Scanning Electron Microscopy (CCSEM), and wire line logging. The Miocene-age paleo-beach deposits are located below a thin Quaternary cover in a region of very moderate relief and essentially no outcrop demanding unique approaches in exploration. Initially, an isopach map of the Quaternary is prepared from existing water well data. A geological model for likely occurrence of Miocene paleo-beach deposits is generated and the coincidence of thin Quaternary cover and potential paleo-beach deposits define targets for detailed exploration. The defined targets are traversed with GPR to identify paleo-beach structures which are then used to define a drilling program. This methodology located a paleo-barrier island at the Vorslunde location with more than 10% ilmenite in the sand. During the drilling process, the TiO2 and heavy mineral contents of the sand were logged every meter with a portable XRF unit (XMET) and subsequently calibrated more accurately by comparison to bulk XRF and CCSEM analyses for selected samples. The bulk XRF data also provided more complete compositional information. Insitu determination of geology, heavy mineral abundance, and corroboration of the XRF logging was done using wire line logs, a combination of spectral gamma and induction conductivity logs. Detailed characteristics (abundance, grain size, shape) and chemical composition of minerals was determined by the GEUS CCSEM methodology (Frei et al, this vol.). The average weight percent TiO2 for all Ti-minerals is 62%, 60% excluding rutile. That elevated TiO2 content (>> ilmenite stoichiometric value, ca. 50 %) indicates that ilmenite experienced an iron-leaching environment. The source of the sand deposit was investigated by dating contained zircon. The results show that the likely sources of zircon are in southern Norway and southwestern Sweden with common zircon ages of ca 1100 Ma. and 1500 Ma.

Jan 1, 2005

By A. J. Opinsky

THE purpose of this note is to indicate the locations and sizes of various interstitial holes in the orthorhombic uranium lattice based on a hard-sphere model. First, plane configurations of three and four atoms will be examined, and then the true interstices surrounded by four atoms in space and by five atoms in space will be obtained. The data and notation contained in a report by Tucker' will be used. Plane Configurations Fig. 1 presents the orthorhombic uranium lattice made of spheres touching at the closest interatomic distance. The three light-colored spheres in the ab plane are illustrative of the first type of configuration to be examined. If one edge of the unit cell is taken as the origin, the three atoms can be represented by the vectors [Oi + Oj + Ok], [ai + Oj + Ok] and [(a/2)i + (b/2)j + Ok] where i, j, and k are respectively parallel to a, b, and c. In the future, this notation will be shortened to [000], [a00] and [a/2 b/2 0], respectively. A vector R = [r s t] de-scribes the position of the hole surrounded by the atoms. Since the center of the hole must be equidistant from the three atoms R2 = r2 + s2 + t2 = (r-a)2 + s2 + t2 = (r-a/2)2 + (s-b/2)2 + t2. R = [a/2 (b/4) - (a2/4b) 0] is the solution of these

Jan 1, 1955

By James W. Martin

This user's manual analyzes the application, selection and performance of front-end loaders in mining operations which can effectively utilize their load-and-carry capability. All aspects of the application are considered starting with a discussion of the load-and-carry system and alternate material handling methods. Site conditions such as the geology of the formation, material characterisitics, alternative mine plans and working conditions are identified. Selection considerations include machine design characteristics, production capabilities and ownership and operating costs. Typical operating practices and safety procedures are discussed. Comprehensive machine specifications, together with a series of checklists and worksheets, are included for preliminary analysis.

Jan 1, 1981

By David C. Benson

This Bureau of Mines report is an update of IC 8725 and comprises tables listing the name, location, and other pertinent data concerning certain fuel-related projects. The tables include information on projects involving the proposed or planned development of fuel resources, as well as the development of storage, transportation, and conversion facilities; the report covers the 26 States east of the Mississippi River. Of the total 535 projects for which information is provided, 429 concern coal mines and electric generating plants (including Energy Supply and Environmental Coordination Act (ESECA) coal conversion notices).

Jan 1, 1978

Several of the larger copper projects recently built have included a molybdenum byproduct circuit as part of the overall project due to the favorable molybdenum market conditions and overall economic contribution to the project. This paper provides a summary of moly plant flotation practices across a number of both recent projects and historical ones. Modern Molybdenum flotation flowsheets predominantly incorporate self-aspirated cells and forced air cells with nitrogen addition. The paper provides insight into the process considerations, capital and operating costs associated with both of the cell types. It also reviews metallurgical aspects and important safety aspects. Other aspects including instrumentation and degree of automation are also discussed along with overall plant design.

Feb 27, 2013

By S. A. Abdel Sabour

Conventional methods for selecting a production plan for an open pit mine is based on the assumption that ore grades throughout mine life as well as market variables are known with certainty. Another important issue that is also being ignored in the conventional procedure is the value of management flexibility to revise operating policy with time according to the arrival of new information. Based on this oversimplification of reality, an optimum mine plan that is thought to be maximizing net present value (NPV) of the project is selected. Given the multiple sources of risk affecting the estimated NPV, there is a high probability that the actual value will be different from that estimated. This could mislead decision making process regarding selecting an optimum mine plan. This paper proposes a multi-criteria ranking system for selection between alternative mine designs under both geological and market uncertainties. The system is based on integrating multiple market and geological uncertainties as well as the operating flexibility to revise the ultimate pit limits using a Monte Carlo-based real options valuation (ROV) model. To compare the methods, the article applies the proposed system, along with the conventional NPV-based method, to rank possible mine designs for a copper and a gold mine. It has been found that, considering multiple risk analysis measures while integrating uncertainty and operating flexibility results in selecting a mine design that is different from that selected by the conventional method.

Jan 1, 2009

By R. S. Warfield

Several reconnaissance-type surface and drill core samples of Arctic Northwestern Alaska coals were taken during the summer field seasons of 1964 and 1966 for coking studies. Surface samples were taken from the Kokolik River and the Cape Beaufort areas; core samples were obtained from the Kukpowruk River and the Cape Beaufort areas. Only one Kokolik River surface sample possessed coking properties. This sample, representing an 11.6-ft coal seam, made coke approaching metallurgical quality when a 30-pct portion of selected blending coals was added. Four Kukpowruk River core samples, each representing the same 19-to 20-ft coal seam, were all of about the same coking quality. No differences of coke quality attributable to depth of permanently frozen overburden were found, but the data confirm previously reported information that the 19- to 20-ft coal bed is a potentially satisfactory base coking coal. In the Cape Beaufort area, a core sample with appreciable coking properties was taken at depth from a coalbed determined noncoking in a surface sample.

Jan 1, 1969

By A. C. Fieldner

"Gas hazards may be divided into two principal classes- namely (1) inflammation and explosions; (2) asphyxiation and poisoning. Inflammation and explosion are prevented first by adequate ventilation so that gas sufficient to propagate flame or explosion can not accumulate, and second, by avoiding sources of ignition such as open lights, flames, sparks, electrical arcs, short circuits, or sparks. Ventilation is also the best preventive measure against asphyxiation and poisoning from toxic gases. When men must enter unventilated or poorly ventilated places containing poisonous or asphyxiating gases, suitable gas masks, hose masks, or oxygen breathing apparatus should be worn. As a rule, loss of life and property from gas hazards is due to ignorance of the properties and hazards of various gases commonly used, and consequently a failure to use proper measures for eliminating and meeting these dangers. It is the purpose of this paper to describe briefly the common gases and vapors with respect to the hazards involved in their use and to discuss the necessary precautions and methods for avoiding these dangersLight, heat, and power are prime essentials of our modern industrial civilization. The combustible gases and vapors used for the production of these necessary elements of our existence comprise the largest and most common group of domestic and industrial gas hazards. Almost every individual in his daily life subject to possible danger from asphyxiation, fire, or explosion due to one or more of these gases. For evidence one need only refer to the daily newspaper where headlines such as the following are frequently seen; ""Family asphyxiated by carbon monoxide from gas heater;"" ""Schoolhouse wrecked by gas explosion in basement;"" ""Man killed by automobile exhaust fumes in his garage;"" ""Fireman overcome by smoke fumes in basement ""Woman"".""Boman severely burned by accidental ignition of gasoline used in cleaning gloves;"" and 'in recent Years we often see ""Building wrecked by explosion of still in residential district.""It will be noted that these accidents are due to inflammation, explosion, or asphyxiation. Any combustible gas or vapor, when mixed, with air or oxygen within certain limiting proportions, will explode on ignition. The violence of the explosion varies with respective proportions of air and gas, and with the degree of confinement of the mixture. For example: Mixtures of natural gas and air containing between 4.5 and 12 per cent natural gas will explode, or propagate flame throughout the mixture without the continual presence of the source of ignition that started the inflammation. The table following gives the explosive limits of the common combustible gases and air:"

Jun 1, 1926

By John H. Johnson

This report covers research which is directed toward the measurement and control of underground mine diesel emissions. The report consists of three separate reports presented as Sections 1, 2, and 3. Section 1 "Emissions Measurement Apparatus" (EMA 1) discusses the selection and evaluation of instruments and procedures to be used as part of a diesel tailpipe emissions dilution and measurement apparatus. The instruments selected for gaseous pollutants are the Energetics Science Inc.* E.S.I.) 2000 for CO, the E.S.I. 7000 for NO and N02, and the Fuji ZFP5 for C02. Particulate matter is presently measured with the Celesco 1013 Smoke Opacity Meter. The raw exhaust concentration of one of these constituents is used Lo calculate the dilution ratio. Either a modified high range E.S.I. 2000 CO instrument or a Daco Products Cobra C02 instrument can be used, but neither is totally satisfactory. The study also indicated that it may he possible to increase the sample collection time from 15 seconds to the total 30 seconds over which the engine can be loaded without increasing the probability of damaging the vehicle hydraulic systems. Section 2 "The Effect of Fuels, Catalysts and a Filter Trap on Drift Pollutant Concentrations" discusses research in the Mine Air Quality Laboratory. A Wagner ST5D LHD with a Deutz F8L714 engine was used to compare three exhaust aftertreatment devices and a muffler-only system. The effect of these four systems on CO, C02, NO and N02 and on total, soluble, sulfate, and solid particulate matter was measured in the drift and on the LHD. The filter trap successfully reduced particulate matter for both fuels without significantly increasing the concentrations of any of the other constituents. The PTX catalyst was effective in reducing CO, and soluble particulate, but significantly increased N02 and solid and sulfate particulate matter. The Oxy Cat catalyst tested didn't seem to he working on the gases, and it significantly increased sulfate, soluble arid solid particulate concentrations. Section 3 "Diesel/Coal Particulate Matter Characterization by Laser Raman Spectroscopy" covers basic research on a method for determining the percentage by weight of diesel particulate on a filter containing a diesel-coal mixture. Signal-averaged Raman spectra provide the necessary precision. The method developed is non-destructive and uses as-received filters requiring no sample manipulation. Particulate with diesel contents in the range of 10 to 50% by weight have been analyzed with accuracies better than 6%t of the mean value. A number of samples containing diesel-coal mixtures were characterized by the procedures developed and the results are analyzed in light of various spectral and other system variables including coal rank and form and diesel engine operating conditions.

Jan 1, 1982

By Howard Martens, Pol Duwez

XPERIMENTS were performed on a Cr-Fc alloy Econtaining 44.7 pet Cr in order to determine the heat evolved during the transformation of the a solid solution into the s phase, and the change in volume accompanying the transformation. Since previous measurements on the rate of formation of a from s indicated that the reaction was quite fast as soon as the equilibrium temperature of 820°C was exceeded by some 50°, standard thermal analysis experiments were performed on heating specimens of s at the rate of approximately 40°C per sec. A definite thermal arrest was observed at 870"C, Fig. 1. This result indicates that the reverse seaction of into a is exothermic. From the heating curve of Fig. 1, taking 15°C per sec as the heating rate in the neighborhood of the transformation, 2.4 sec as the time for transformation, and assuming that the specific heat of the alloy at 850°C is an average between iron and chromium, namely 9.5 cal per mol per "C, the latent heat of transformation is approximately 342 cal per mol. The order of magnitude of this latent heat was also obtained by comparing the heating curve of Fig. 1 with a similar curve obtained with pure iron under identical experimental conditions. It was found that the length of the thermal arrest for s was about 1.8 times as long as that for iron. Since the latent heat of the a to 7 iron transformation is 203 cal per mol1, 2 the latent heat of it to a would be 365 cal per mol, which is in relatively good agreement with the value determined from the heating curve. For the determination of volume change, thermal expansion curves were recorded using a specimen containing 44.7 pet Cr and completely transformed to cr by previous treatment. The curves were recorded at a rate of heating of about 4°C per min and at approximately 840°C a sharr, increase in length of about 0.08 pet took place. Fig. 2. It is therefore established that the specific volume of a near the transformation temperature is about 0.24 pet smaller than that of a, and consequently, when the s phase forms in an a matrix, it would tend to shrink away from the matrix. Since the s phase is known to be extremely brittle, these results offer an explanation for the microscopic cracks often observed in the a phase under the microscope. The results of this study are in qualitative agreement with previously published data on stainless steel 19-9DLa and on a Cr-Fe alloy containing 45 pet Cr.' The increase in density due to the transformation from n to s given in ref. 4 is 0.90 pet. These measurements, however, were made at room temperature. whereas the presently reported 0.24 pet is the change at the temperature at which the transformation takes place during heating. In the graph of Fig. 2, the percentage change in length that would be observed at room temperature is given by the length X, which is about 0.27 pet. This would correspond to 0.81 pet in volume change. Acknowledgment This work was done at the Jet Propulsion Laboratory, California Institute of Technology, under Contract No. DA-04-495-ORD-18 with the Army Ordnance Corps, Washington, D. C. The authors wish to thank this agency for permission to publish the results of this investigation. References I H. Klinkhardt: Measurements of True Specific Heats at High Temperatures. Annalen der Physik (1927) 84, pp. 167-200. - H. Esser and W. Runghardt: Influence of the Method, of Dctcrmination on the Measured Heat Content of Iron. Archtvo ffur Dct Eisenhiittenwesen 11934) 8, pp. 37-38. J. J. Gilman, P. K. Koh, and 0. Zmeskal. Delta Ferrite Formation and its influence on the Formation of Sigma in a Wrought Heat Resisting Steel. Trans. ASM 1 1949) 11, pp. 1371-1388. 1 J. M. Thomas: Discussion of ref. 3. Trans. ASM (1949) 41, pp. 3 390-1392.

Jan 1, 1957

By G. Richards Gwinn

"Mica" is a group name for a number of orthosilicates of aluminum with magnesium, ferrous iron, and the alkalies. They are characterized by their high reflection and a basal cleavage so well developed that they can be split into exceedingly thin laminae, which are more or less tough, elastic, and transparent, according to variety. Barium, manganese, lithium, chromium, titanium, boron, and ferric iron occur in same varieties. Eight distinct species of true mica, which appear in the following table, are recognized by mineralogists, but only the first five are of commercial importance. [Species General Formula Muscovite H2KA13 (SiO4)3 Phlogopite [H,K, (MgF)]) Mg3A1 (Si04)3 Biotite (H,K)2(Mg,Fe)2(Al)Fe)2 (S104)3 Lepidolite K,Li Al(OH,F)2 Al (5103)3 Ros coalite H8K(Mg,Fe) (A1,V)4 (S103)12 Paragonite H2NaAl3(S104)3 Zinnwaldite (K)Li)3 FeAl3 Si5016(OH,F)2 Lepidomelene HK2F3IIIFe6III A13 (S104)9]

Jan 1, 1951

By Robert L. Lagace

This report presents a mathematical model for the propagation of UHF radio waves in the large cross-section tunnels of a room and pillar limestone mine, and describes the analysis of a small amount of propagation data obtained in a limestone mine. The model and analysis is based on the waveguide mode theory developed earlier for the transmission of UHF waves in coal mine tunnels, with allowance for propagation losses due to refraction into the tunnel walls, to scattering by wall roughness, and to long range random tilt of the walls. Propagation around corners and through pillars is also examined based on a ray theory approach, together with the beneficial effects of placing reflectors at intersections to significantly reduce corner losses. The theory is found to be in fair agreement with the data; however, additional in-mine measurements are needed to provide a more conclusive test of the model.

Jan 1, 1979

By C. A. Pickles, J. M. Toguri

The refining of two molten Ag-Cu alloys, containing 7.5 and 11.2 mass% Cu, with a borosilicate slag was investigated using both air and pure O2 to determine the effects of the following variables: flow rate of oxidising gas; injection time; mass of sodium borosilicate flux; and injection of the oxidising gas into either the slag or the metal. The results demonstrate that more than 90% of the Cu can be removed with Ag losses of less than 5% and that refined metal with a Cu content of less than 0.5 mass% can be produced. Ag losses to the slag increased with the amount of Cu removed, and a mechanism is proposed to account for this

Dec 1, 1995