Search Documents

By P. M. Daling

This report, sponsored by the U.S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures, and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982

By H. Möhle

Premier Mine is a large underground diamond mine, situated at Cullinan in the Gauteng Province of South Africa. The mine hoists over 3 millions tons of diamond bearing kimberlite per year, from a modern, mechanized panel retreat block cave mining operation. Troughs sited at the base of the cave are developed into the overlying caved ore, allowing loading access to the ore through draw points. Trough opening is therefore a vital aspect of the mining operation. Most of the production is dependent on fast, reliable and safe trough opening. Successful trough openings are achieved under difficult mining conditions due to restricted void, long up-holes and the inherent properties of kimberlite?soft, elastic rock with a high swell factor. Early in 1998, Premier Mine undertook a joint development project (with an electronic initiation system supplier) to determine whether the use of a fully programmable electronic detonator system would enhance the mining cycle in the trough opening process. Blasting commenced in February 1998, initially with blasts of a similar size and duration to those that had been previously blasted with shock-tube systems, to confirm the operational capabilities of the blasting system. The accuracy, reliability and flexibility of the electronic delay detonators (EDDs) minimized associated risks for re-engineering of the trough opening process. Further, as blast timing was optimized, larger blasts were successfully initiated. To date over 20 troughs have been opened successfully with the use of EDDs. Not only did it take less time to open troughs, but also drilling and blasting operations have been optimized, as well as an overall improvement in safety. This paper details the benefits that EDDs have delivered to Premier Mine in this area. The logic followed is: ?Review of the original trough opening practices ?Re-engineering of the trough opening process ?Implementation of EDDs ?Evaluation of improvements and conclusions.

Jan 1, 2000

By J. Yao

Synthetic indium-bearing zinc ferrite (IBZF) was mechanically activated by a tumbling mill. Subsequently, the behavior and kinetics of leaching zinc and indium from the initial IBZF and activated IBZF in sulfuric acid solution were investigated. The results demonstrate that the tumbling ball milling enhances the leaching reactivity of IBZF and increases the zinc and indium extractions. The reaction temperature and H2SO4 concentration have an important effect on leaching zinc and indium from the initial IBZF and activated IBZF. The kinetic model -ln(1-x) = kt was used to describe the kinetics of leaching zinc and indium from the initial IBZF and activated IBZF and to calculate the kinetic parameters. The tumbling ball milling causes a decrease in activation energy and reaction order, which indicates that the dissolution of IBZF after mechanical activation by a tumbling mill becomes less sensitive to temperature and H2SO4 concentration. For the zinc leaching, the activation energy decreases from 73.9 to 70.3 kJ/mol and the reaction order decreases from 0.72 to 0.70. For indium leaching, the activation energy decreases from 78.1 to 73.5 kJ/mol and the reaction order decreases from 0.82 to 0.69. It is found that the dissolution rates of the initial IBZF and activated IBZF are controlled by surface chemical reactions.

By P. P. Andrieux

The recovery of the Zone G crown pillar, located between the bottom of the open pit and the top of the underground workings at the Raglan Katinniq Mine in Nunavik, started in the summer of 2008 and should be completed by the end of 2009. This article describes the rock mechanics-based approach implemented to design the recovery of this valuable block of ore. The stereophotography-based ShapeMetriX3D technique was first used to provide a comprehensive assessment of the various joint sets that comprised the pillar. Then, the statistical distributions obtained for the dip, dip direction, spacing and persistence of these sets were used in conjunction with the geometry of the large-scale faults present in the area to build and run a series of explicit rigid numerical models. Each of these models had a slightly different jointing geometry, randomly constructed from these statistical distributions. Incorporating in a properly formulated numerical model the variability of some of the input parameters has allowed the engineering team to assess in a rational and reliable manner the likelihood of success of the proposed mining method and sequence.

May 1, 2009

By V. K. Kollipara

Air flow patterns in the face area of a room-and-pillar mining are critical for understanding the dust dispersion characteristics and for developing engineering controls. SIUC has previously performed a CFD study to analyze the airflow patterns in the face area when continuous miner is making a straight cut. Results from this study identified low air velocity and re-circulation zones in the face area and illustrated the significance of line curtain, and scrubber operation on the air flow patterns. This paper discusses similar analyses when continuous miner is making a right turn cut as it is considered to be the dustiest cut among all the cuts made to advance an entry through a crosscut. This paper presents results for box-cut development for a right hand turn x-cut. This paper also addresses line curtain advance and air leakage through the curtain on the airflow patterns in the face area for such a cut. Low air velocity and recirculation zones were identified by analyzing the velocity vectors.

Jan 1, 2012

By H. Michael Breza

Texasgulf Inc. installed bucketwheel excavators and overland conveyor sysems at its Aurora, NC phosphate mine o increase the productivity and flexibilty of the surface mining operation. This ;ystem has significantly improved overrall. Its flexibility is evidenced by adapation to operation requirements, such is mining area moves, movement of xcavated overburden to designated ites, selective handling of overburden, poll placement contouring, and proiding an environmentally sound and afe operation. The system's productiv:y is evidenced by case studies relating. overall production, excavation rates nd cost-effectiveness. There are many competing alternaves available for excavating uncon)lidated overburden: truck-shovel, raglines, dredges and bucket wheel ticavators. These alternatives also may used in tandem to recover reserves icated at greater depths.

Jan 1, 1993

Study on the Reasonable Mineral Processing Technology of a Cu-Mo Ore

Sep 13, 2010

By M. Troyer

A coal shuttle car equipped with a pulsed laser optical ranging system to provide guidance for an automatic steering system was tested in production coal mining. Test results are presented for the two mines where testing took place, and some operator's reactions are included. Automatic steering control keeps the car cantered in an entry, and automatic turns are made at intersections as signaled by the operator. All other controls-tram, conveyor, brake, etc, remain manual and require operator control. Complete override of steering while in the automatic mode is retained by the operator, who may grab the steering wheel at any time and turn in opposition to the automatic signal by applying about 10 foot-pounds of torque.

Jan 1, 1976

By Rudolf E. Greuer

This report contains the practical application of a computer program for the simulation of ventilation systems under the influence of mine fires and other emergencies on five hardrock mines. The introduction describes the need for such a program, its basic features, and the range of its applicability which is mainly a function of the available ventilation data. The second chapter discusses program modifications, whose necessity or desirability was, during the application, discovered. The following five chapters, which comprise the major portion of the report, give the detailed description of the program application on the five mines. For every one of the selected mines, the ventilation system, the source of the used ventilation data and their preparation for computer simulations are outlined. Based on data for the airflow distribution solely, fumes concentrations in the mines are calculated for several assumed fire locations. Based on data for airflow and pressure distributions, ventilation disturbances caused by fires as well as the resulting fumes concentrations and temperatures are determined. The consequences for escape routes and the possible means to keep them free of fumes are discussed. To investigate the capabilities of the program, other contaminant sources and other potentially dangerous ventilation factors, like fan failures and changed surface temperatures, are simulated also. The results of the calculations have been entered into ventilation plans which makes them easier to scrutinize. All significant computer printouts have been attached.

Jan 1, 1981

By Richard Rittenhouse

This program was to develop a new base line system for automated continuous room and pillar type mining. The primary requirement estab¬lished for this machine is that the machine be capable of mining and bolting simultaneously. Additionally, this machine was to provide temporary and permanent roof control, have a productive - full - face semi-automatic mining system, leave a clean entry outby the machine, provide maximum operator protection, provide effective dust suppression and provide air scrubbing to restrict respirable dust to permissible levels. The machine has effectively demonstrated the ability to mine and bolt simultaneously. Additional above ground operation, testing, and time studies are recommended to further verify the machines abilities. Design improvements are recommended for future generation AES machines. These relate to marginal design areas such as side loading on vent duct lift cylinders, etc., that will not impair additional testing of the existing machine.

Jan 1, 1983

By Mengxiong Guo, Xuxin Shao

The recent depressant research is summarized, and a new kind of depressant (SCO) has been put forward in this article. Using Na-oleate as a collector and SCO as a depressant, separation of dolomite and phosphate was studied. When SCO was added in the concentration range of 80 g/t to 2kg/t at pH 9.5 ± 0.2, dolomite was absolutely depressed, and apatite kept its floatability. Interestingly, in the mixture of phosphate and dolomite, the dolomite floated. The reasons for such a behavior are investigated through flotation and electrokinetic studies. It was found that the adsorption of dissolved species on dolomite and phosphate resulted in reverse flotation. A concentration of 31.59% P205 and 83.87% recovery of P205 was obtained from the mixture of phosphate and dolomite (2:1) with 26.6% P205 using 210 g/t SCO and Na-oleate 4.93*10-5 M at pH 9.

Jan 1, 1989

The Khanong supergene-enriched copper resource, (~23 Mt at 3.0 per cent Cu), is one of several resources recently discovered in the intrusive-centred, sediment-hosted Au-Cu Sepon mineral field located in southern Lao PDR. The unusual style of hypogene mineralisation and unique set of conditions have resulted in the development and preservation of a supergene-enriched profile in this subtropical climate. Hypogene sulphide-rich mineralisation replaced calcareous cataclastite (fault rock) developed in the flat-lying, extensional, Khanong Fault. Spatially, the hypogene mineralisation was immediately out board of the skarn û hornfels Cu-Bi front and in board of sediment hosted Au-(As-Sb) mineralisation in a zoned intrusive-centred hydrothermal system. In situ supergene enrichment of the sulphide protore has resulted in a high-grade chalcocite-clay zone (~10.3 Mt at 4.6 per cent Cu) overlain by leached limonite-clay. A very high-grade in situ to exotic limonite-clay Cu-oxide-mineral zone is locally developed above impermeable dolomite at the base of chalcocite-clay zone. Exotic Cu-Mn-wad mineralisation developed for up to 1 km down the hydraulic gradient from the chalcocite-clay zone. Unique supergene enrichment conditions have resulted in the high-grade Khanong Cu resource in a subtropical weathering environment. The base of the currently active supergene profile coincides with the base of a flat-lying, pyrite-rich fault rock, dipping parallel to the hill slope, maximising Cu enrichment. Meteoric water has been channelled along subvertical faults and narrow horizontal subsurface zones. Low permeability of the fault host rock and footwall rocks has controlled the low volume and slow movement of groundwater required for supergene enrichment. Erosion has been slowed by the resistive ironstone and limonite-clay layer at surface, which assists in preserving the gentle slope over the chalcocite-clay zone.

Jan 1, 1999

(Members are urged to send in for this column any notes of interest concerning themselves or their. fellow-members.) Members and guests who registered at Institute headquarters during the period Nov. 10 to Dec. 10, 1914: H. F. Grondijs, Oruro, Bolivia. E. B. Kirby, St. Louis, Mo. R. W. Shumway, Denver, Colo. W. R. Webster, Philadelphia, Pa. J. N. Houser, Mascot, Tenn. F. S.. Titsworth, Denver, Colo. F. L. Clerc, Denver, Colo. Frank R. Wicks, Butte, Mont. Robert Sticht, Queenstown, Tasmania. C. Q. Schlereth, Denver, Colo. Francis C. Phillips, Pittsburgh, Pa. Robert Hallowell Richards was given a dinner on December 7 at Boston by the corporation, faculty and alumni of Massachusetts Institute of Technology in recognition of his 50 years as a devoted alumnus and teacher and as an expression of the respect and affection in which he is held.

Jan 1, 1915

By R. A. Harris

In this study Pt-Al thin films were prepared via electron beam physical vapour deposition (EB-PVD) with an atomic concentration ratio of Pt25:Al75. These films were heat treated at temperatures ranging from 150°C to 650°C for annealing times from 4 to 60 minutes. The resulting microstructure of these thin films were obtained via secondary electron imaging used in conjunction with depth profiling with the aid of scanning auger microscopy (PHI 700).Elemental maps of the micrographs were obtained. Simulations, based on a chemical potential Monte Carlo method1, were run for various interaction parameters. From these simulations theoretical depth-profiles and proposed microstructures were obtained. These were compared to the experimentally measured depth profiles and elemental maps. Keywords Monte Carlo, chemical potential, depth profile, Pt-Al thin films.

Jan 1, 2011

By Chas. F. Jackson

The annual reports of the supervising engineers of the nine sections comprising the Mining Division are assembled here and constitute the annual report of the division. In planning activities the aim is to adapt them to changes in conditions, in the needs of the mining industries, and in the public interest; those that contribute most to solving the present problems are emphasized, investigations of less immediate importance being recessed if necessary. The strategic minerals investigations of the bureau afford an example of this change in emphasis to problems of immediate and urgent interest, and during 1941 they comprised, upon the basis of appropriations and expenditures, more than 90 percent of the work of the division.

Jan 1, 1941

By Allan E. Martin

As part of a comprehensive investigation of tie mechanism of desufurization of iron and steel by slags, the Blast Furnace Studies Section, Metallurgical Division, Bureau of Mines, in cooperation with the Institute of Technology-, University of Minnesota, has made a study of the forms in which sulfur occurs in blast-furnace slag. This report presents data on the three sulfides most important in iron smelting, namely, ferrous sulfide, manganous sulfide, and calcium sulfide. The tendency of these sulfides to form colloids in the molten slag was determined by an examination of quenched samples with an ultramicroscope. Vogt5/ conducted experiments on sulfide silicate melts and examined synthetic blast-furnace slags in a partly crystallized condition. His conclusions were that FeS, CaS, and bins, or isomorphous compounds, such as (FexCay)S and (MnxCy)S, were precipitated Prom the melt, depending on the composition of the slag. In all specimens sulfides were visible and were spherical.

Jan 1, 1941

By E. D. Gardner

"Trolley lines used in connection with electric haulage in mines are a source of danger and many lives have been lost by men accidentally coming in contact with the wires. Usually the wires in metal mines are sufficiently guarded to prevent men from touching them with their person or by pieces of steel which they may be carrying or their shoulders, while walking along the level. However, it is difficult to guard effectively the wires at loading chutes along the haulage ways and in spite of safe guards, chute tappers have been electrocuted through loading bars accidentally touching the trolley line.To overcome this danger the Calumet & Arizona Mining Co., at Lowell, Arizona formely used a hinged V-shaped trough made of 1-inch by 6-inch lumber, that was dropped over the wire in front of the chute, when the cars were being loaded. This arrangement interfered with the easy operation of the chute, and a cut-out device for the trolley line was devised by W. R. Gibson, chief electrician for the company. This cut-out is efficient easily constructed and roes not interfere with the operations at the chutes or with the motors operating on the same level.When the cut-out is open the electric current is carried past the gap by an insulated wire on the opposite side of the drift. A hinged board drops down over the ends of the trolley guard when the slide is open and Prevents anything touching the live wires. About ninety of these cut-outs are now in use in the mine,The levels under the scopes are timbered with drift sets placed 5 feet apart, and the loading chutes take up the space between two sets. All trolley wires in. the company's mines are carried 6 feet above the rails and guarded by two 1/2 by 6-inch boards placed on either side of the wire."

May 1, 1921

By Ali Mortazavi

In underground mining applications, successful blasting results in less damage, which may lower support costs, lower dilution and produce a uniform fragmentation. The explosive detonation process creates a pressure front that propagates a stress wave into the surrounding rock mass at a high velocity. The stress wave can induce varying degrees of damage, depending on rock strength and physical properties, to the excavated area. This paper presents a summary of a research project that was conducted to investigate the propagation of explosive-induced stress waves in hard rock media and the mechanism of rock damage and fracturing due to shock wave propagation. The primary objective of this work was to numerically simulate the experimental study of blast-induced rock fracturing conducted within Inco Limited, Mines Research department. ITASCA?s discontinuum code UDEC (Universal Distinct Element Code), was used to simulate the results of the controlled blasting experiments. In brief, the focal point of the paper can be summarized as follows: ? Investigate the size of the stress-wave-induced fractured zone around the blasthole, ? Examine the extent and direction of the radial fractures that form outside the blasthole, and ? Explore the mechanisms that cause rock breakage.

May 1, 2002

By A. M. Cann, C. I. Godwin

"The Kemess porphyry copper-molybdenum deposit occurs in the Intermontane Belt of north-central British Columbia. The deposit is in andesitic to basaltic flows and tuffs which may be correlated with the Savage Mountain Formation of the Upper Triassic Takla Group. Most known chalcopyrite and molybdenite is associated closely with a 500-m-diameter zone of intense quartz-sericite-pyrite alteration. A zone of supergene enrichment, up to 30 m thick, underlies a leached capping about 20 m thick. The age of mineralization and the surrounding granodiorite and quartz monzonite pluton is Early Jurassic. K-Ar and Rb-Sr analyses indicate that the mineralization and alteration is slightly younger (l82±6 Ma) than the granitic intrusion (KAr: about 205±6 Ma; Rb-Sr: 190±4 Ma). The low 87Sr/J6Sr initial ratio for the granodiorite is typical of plutons in the Intermontane Belt.IntroductionKemess is a medium to small porphyry copper-molybdenum deposit with significant gold and silver values (Pilcher and McDougall, 1976). This paper describes the lithologies and alteration at this property; geochronology by Rb-Sr and K-Ar methods defines the ages of mineralization and surrounding plutons to be Early Jurassic.The property, located in the Thutade Lake area of northcentral British Columbia (NTS Map 94E; lat. 57°04'N; long. 126°44'W), is about 425 km northwest of Prince George (Fig. 1). Closest road access is 35 km southeast of Kemess. Final access must be by float plane or helicopter. The British Columbia Railway right of way passes 70 km to the southwest of theproperty.A prominent gossan zone at Kemess was staked in 1967 by Kennco Explorations (Western) Ltd. following detection of geochemical anomalies during stream sampling the previous year. During 1968, 1969and 1971, Kennco completed 232 m of X-ray diamond drilling, conducted geological mapping and carried out geochemical sampling of silts and soils (Stevenson, 1969; B.C. Ministry of Energy, Mines and Petroleum Resources, G.E .M., 1969 and 1971). Getty Mines Ltd. optioned Kemess in 1975and 1976. They remapped the area and diamond drilled 12 BQ and NQ holes, totalling 2065 m (B.C. Ministry of Energy, Mines and Petroleum Resources, Expl. B.C., 1975)."

Jan 1, 1980

By A Priatna, H Rumbino, T Casten

This paper discusses the progress of the Deep Mill Level Zone (DMLZ) mine from the pre-feasibility study completed in 2005, through commencement of development access in 2008, completion of the feasibility in 2010 and cave initiation in late 2015. This fourth lift of caving in the East Ertsberg Skarn System (EESS) is located 500 m below the currently producing Deep Ore Zone (DOZ) mine and represents approximately half a billion tonnes of ore and around 1900 planned drawpoints, scheduled to be mined at a peak of 80 000 t/d.The paper reviews the mine design, access requirements, planned footprint sequence and major fixed facility installations such as ventilation, oreflow and shops. A discussion of the preproduction development and construction activities and some of the critical technical challenges overcome during this time frame are addressed, as well as the cave initiation process undertaken in late 2015 and the ramp-up of production and progression of caving.CITATION:Casten, T, Priatna, A and Rumbino, H, 2016. Deep Mill Level Zone – from feasibility to production, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 635–644 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016