Search Documents

By E. K. Stanek

The field tests involved ten coal mines in which transients were initiated on the dc system from which the parameters of the dc mine electrical power system could be determined. The data processing involved the use of a Fourier Analyzer to filter noise and fit an exponential curve to the field waveforms. From this data analysis it was possible to find the dc system resistance, inductance and time constant. The survey of nationally recognized laboratories was conducted to establish that the recommended test criteria were practical. The development of test criteria for dc fuses used in mines was based on the measurement of parameters in the field, the survey of testing laboratories, literature searches, laboratory test, etc. A computer program was written to analytically predict the parameters measured in the field. This approach has limitations but reasonable agreement with field results was obtained. A brief laboratory testing program was carried out to verify the practicality of the recommended criteria and establish the accuracy of the conclusions concerning dc fuse performance.

Jan 1, 1984

By G. F. Sowers

Excavation bracing is a special structural system. It is built from the top down. The design is controlled by the economical construction of another structure as well as by the movement of the ground beyond the limits of its construction. It serves a number of purposes, all subordinate to the construction of the principal structure. Despite its importance, bracing design and construction is frequently overlooked in project planning, causing delays and expensive changes. Thoughtful planning, good design and resourceful, innovative construction can improve construction safety and save time and money.

Jan 1, 2010

By Joseph D. Davis

Selection of a suitable coal or coals for the manufacture of coke of desired quality with due consideration of the purpose for which the coke is intended requires careful thought, and often it will pay to go to consider able expense in testing such coals as may be available. In general it will always be possible to obtain a satisfactory coal or blend of coals for the particular purpose in view, but in some places the cost of transportation would be prohibitive. It may then be necessary to consider a coal or coals inferior in grade, rank, or both. At times, in fact, only one inferior coal may be available, when the problem becomes mainly one of selecting equipment and operating conditions best adapted to that coal, keeping in mind that the end product of the plant must compete with the imported product in the market the plant will serve. This applies particularly to new projects for which it is necessary to build a plant and start with a clean slate, so to speak. However, it will pay every coke-plant manager to employ a force to continually test the coals used and the coke produced to make sure that the quality is not changing appreciably. Furthermore, if the supply of coals used becomes exhausted it will be necessary to use other coals. Continual testing is particularly necessary at plants using borderline coals or blends, where slight changes in the composition or in operation of the ovens may render them dangerously expanding. In this connection it should be stated that control in the newer coke plants is considerably easier than for those built a decade or so ago, consequently in the new ovens a given operating program can be maintained more precisely. This point is important, because one of the main requirements of the coke user is uniformity in both physical and chemical characteristics. For example, any appreciable changes in the quality of coke delivered to the blast?-furnace operator will involve changes in operation if the best results are to be obtained. Such changes are expensive usually they take considerable time and involve production of inferior iron.

Jan 1, 1942

By Holly J

The period following World War II has seen many changes in stoping techniques at The Great Boulder Gold Mine. The new methods resulted in improved unit production figures, and have given some relief from the rising worldwide cost spiral in the post war years.Significant production figures are shown graphically in...

Jan 1, 1956

By Sara Jane Boles

In recent years the demand for products of greater refractoriness has placed an ever-increasing emphasis on ceramic materials, including the metallic oxides. Magnesia (MgO) is one of the most important of these oxides, exhibiting, as it does, high electrical resistivity, high slag resistance, and a melting point of 2,800° C. However, magnesia has a tendency to hydrate in the presence of water and to volatilize above 1,500° C. in certain kiln atmospheres and has a comparatively low resistance to thermal shock. Because of these disadvantages, the previously listed advantages inherent in this material have been largely overlooked, and research on magnesia has lagged behind that on oxides such as alumina and zirconia. This bibliography has been prepared in an effort to present to Government and industry a comprehensive picture of the prospects for greater utilization of magnesia as a refractory material in future research. To provide as selective and accurate a collection as possible, the references included cover magnesia in a pure state, not as an additive or in combination with other materials. However, several references discuss the effect of minor impurities (less than 5 percent of the total) on the properties of magnesia, as these papers are considered to be of special importance. A few references to articles on forming techniques are also included, as they are valuable additions to the overall treatment of the subject. The processes used in obtaining and refining the raw materials are adequately covered in earlier publications and are excluded. A number of references are omitted as being of questionable value in enhancing the cumulative study of pure magnesia as an ultra-high-temperature refractory material.

Jan 1, 1962

By M R. Dehghan, H Mansouri, A Hakami, M A. Ebrahimi Farsangi, F Faramarzi

Today, it is accepted that rock fragmentation by blasting affects loading and hauling operations, and also directly influences on downstream processes such as crushing and grinding. In this research, the influence of rock fragmentation by blasting on the performance of three mills at Gol-e-Gohar iron ore mine No 1 was studied. Firstly, the fragmentation of conventional blast patterns in iron ore (5 × 6 m) was studied using image analysis and the performances of three mills were monitored. Then, a new blast pattern (4 × 5 m) was designed and nine blasts were carried out using this pattern. Increasing the powder factor form 1650 gr/m3 to 2480 gr/m3 by changing the blast pattern design showed that mill throughputs increase five per cent to 30 per cent for the new pattern.CITATION:Hakami, A, Mansouri, H, Ebrahimi Farsangi, M A, Dehghan, M R and Faramarzi, F, 2015. Study of the effect of blast pattern design on autogenous and semi-autogenous mill throughput at Gol-e-Gohar iron ore mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 315–320 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Daudi R. Waryoba

Keywords: Wire Drawing, OFHC Copper, Recrystallization, Orientation imaging Microscopy (OIM), Texture inhomogeneity Textural inhomogeneities have been investigated in oxygen free high conducting (OFHC) copper wire drawn at room temperature to a true strain of 2.31, and isothermally annealed at 250°C and 750°C for annealing times ranging from 10 s to 1 hr. Local orientations were mapped by means of orientation imaging microscopy (OIM). The microtexture of the drawn wires showed a strong <111> + weak <100> duplex fiber texture at the inner core, whereas the mid and surface regions had a comparatively weak texture. Annealing at 250°C resulted into a recrystallization which originated from the mid section, proceed towards the surface regions and ends in the inner core. Recrystallization resulted into a strong<100>+weak<111> duplex fiber texture. A similar textural inhomogeneity was observed during short annealing at 750°C. However, prolonged annealing gave rise to abnormal grain-growth that proceed from the inner core to the outer surfaces with a dominant <111> fiber component at the inner region and mixed components of <111>, <100>, and <112> at the outer surfaces.

Jan 1, 2005

By E. Kamon

This report summarizes completed research pertaining to the reaction of human subjects exposed to Self-Contained Breathing Apparatus (SCBA) stressors during escape conditions (viz., resistance breathing, C02 breathing, hot air breathing, and static positive facepiece positive pressure breathing) and the development of an automated breathing and metabolic simulator (ABMS). Volume I contains summarizes of the studies performed under this contract. Volume II is an appendix which contains more detailed descriptions of these studies.

Jan 1, 1984

By G. P. Gormley

"Future open pit metallurgical coal mines in western Canada will be developed in complex geological environments. The success of these operations will be influenced by the mine operators&apos; ability to prepare accurate mine plans and to predict and, subsequently, 10 control both out-of-seam dilution and coal recovery. Quintette Coal Limited has been mining its tightly folded and severely faulted Mesa depo sit at annual rates of up to 9 Mt of raw coal, since October 1982. Ongoing development drilling combined with continuous utilization of blast hole information, has been required to achieve an acceptable geological data base for short range mine planning. Thrust faulting has been a primary geological cause of difficulty in selectively mining waste and coal, which has resulted in higher than expected dilution in plant feed. The same geological phenomenon has also increased reserves by 6.3% and allowed for expanded mine plans to include a lower thrust plate, ultimately doubling the mines original reserve base. This paper illustrates the geology of the Mesa deposit and the type of work involved in its interpretation. Regional GeologyThe Quintette Coal Limited (QCL) property is located in the Peace River Coal Field of northeastern British Columbia. In this area, northwesterly-trending folds of the Rocky Mountain foothills are commonly cut by multiple, low-angle thrust faults, which dip to the southwest. The Lower Cretaceous Gates Formation, of near shore continental origin, contains 5 to 7 mineable seams of medium volatile bituminous metallurgical coal (Figs. I and 2). These seams normally range in thickness between 0.75 m and 9.5 m and have an aggregate thickness of between 15 m and 22 m."

Jan 1, 1988

By R. A. Cummings

Certain roof shales in coal mines deteriorate upon exposure to the atmosphere, causing difficulties in the mining operations and adding to the cost. This report presents the results of both field investigations, in a West Virginia mine, and laboratory studies on the effects of atmospheric moisture on roof shales. Based on these observations, a conceptual procedure is presented on how shale deterioration might be predicted during exploration, and guidelines are given as to how air tempering or conditioning chambers may be designed to reduce moisture effects. Recommendations for further studies are included. An annotated bibliography of the literature constitutes the second volume.

Jan 1, 1981

Although auriferous beach and fore-dune sands at Five Mile Beach south of Okarito township had been intensively mined by hand and primative mechanical methods drilling of the sandspit by the Gold Development Corporation in 1929 indicated that the grade and quantity of undisturbed black and grey sand below the water table was sufficient to support a mining operation. Worked sand above the water table also contained fair prospects. The Okarito Five Mile Beach Gold Dredging Co Ltd, was formed and an hydraulically powered, bucket ladder, sluice box dredge built. In 13 years of operation (1931 - 1943) the dredge returned 556.39 kg (17 890 oz) of gold at a recovered grade of 225.4 mg/m3. A total of ú42 000 was distributed as dividends on the ú30 000 capital investment. Recent drill and bulk sampling at the northern end of the beach has confirmed that reworking of the historic tailings by a modern gravity recovery plant would not be economic.

Jan 1, 1993

The pellet plant, built by Dravo Corp, in Groveland, Mich., for the Hanna Mining Co., is now in full operation. Although using jasper, a type of iron ore with low iron content (approximately 28% Fe), the plant has a rated capacity of 1,250,000 tans of pellets per year. In its four years of existence, the nearby concentrating plant has seen its capacity increase from 700,000 tons to 1,500,000 tons a year as part of a major expansion program at Groveland. Utilizing the Dravo-Lurgi continuous grate process, the pellet plant produces %a-in. pellets of more than 60% iron content. The fully-hooded pelletizing grate, largest in the U.S., is 9 ft. 10% in. wide and 223 ft. 1% in. tong over 34 windboxes, with an effective hearth area of 2195 sq. ft. Drying, firing, and cooling functions are all carried out on this single piece of equipment.

Jan 4, 1964

The Ediacara mineral field is classified as a Mississippi Valley type deposit with stratiform mineralization near the base of the Cambrian beds. Mineral deposition was contemporaneous with sedmentation and reerystallization, and mobilization took place after lithification of the sediments. Several mechanisms of deposition were possible.INTRODUCTIONThe Ediacara mineral field is located in the Mt. James Range approximately 300 miles north of Adelaide, about 12 miles west of Beltana railway siding and 10 miles east of Lake Torrens. It is isolated geographically from similar deposits of equivalent age and environment in the Flinders Range Province (Fig. 1). The climate may be described as semi arid with high summer temperatures and frequent dust storms. Occasional thunder storms are the main source of rain in the summer months.The exact date of discovery is unknown, but is believed to be about middle of the last century. Ulrich (1872) was the first geologist to report on the field. At that time only the southern portion of the field had been prospected (and abandoned). Although the prospects did not appear encouraging Ulrich advised prospecting of the shales and testing beneath the limestone.In 1888, Rosewarne, an Inspector of Mines, visited the Southern Workings and queried whether they were connected with some lode at deeper level or were merely bedded deposits. The first geological map with sections was drawn by H.Y.L. Brown (Brown 1892).Brown recognized three principal rock formations as dolomitic sandstone, kaolinised shales and sandstone, and quartzites and sandstone in descending order. These three basic units are still recognized. He recognized also the stratiform nature of the mineralization in the shales as a...

Jan 1, 1963

The schlieren technique describes an optical analysis method designed to enhance light distortions caused by air movement. The ability to visualize air flow has significant implications for analyzing underground mine ventilation systems, including the enhancement of surveys and models. Currently, traditional schlieren methods are impractical underground. Background oriented schlieren (BOS) provides a solution to this problem. BOS requires two primary components, a professional quality digital camera and a schlieren background. A schlieren background is composed of a varying contrast repetitive pattern, such as black and white stripes. This background allows the camera?s sensor to capture minor light diffractions, such as those caused by air flow. Although BOS shows great potential for ventilation analysis, sensitivity is an issue. This paper seeks to validate the BOS technique for imaging flow through a regulator by comparing BOS images with traditional schlieren images. This paper also outlines initial experimental efforts used for the validation.

Jan 1, 2011

By R. Codell, D. L. Hughson

While benchmarking the integrated finite-volume code MULTIFLO against the analytical solution of Philip et al. (1989) for cylindrical underground openings, we found numerical simulation of dripping threshold flux consistently higher than the analytical solution for both rectangular and unstructured grids. The magnitude of error is proportional to the alpha parameter characterizing capillarity. This may bias estimates of repository performance towards non-conservatism.

Jan 1, 2000

By J. C. Cawley

This National Institute for Occupational Safety and Health study was conducted to focus future research on the most significant electrical problems in the mining industry. Data from 1,926 mine electrical accidents (including 75 fatalities) that occurred between 1990 and 1999 were studied. Coal and metal-nonmetal operator- and contractor-reported data are presented. All data used in this analysis were MSHA closeout data, except 1999, which were preliminary data. Electricity was the 4th leading cause of death reported in mining despite being the 14th leading cause of injuries. Electrical shock, not electrical burns, caused 70 of the 75 electrical fatalities reported. About one-half of mine electrical accidents and fatalities occurred during electrical maintenance. Suggestions for mitigating electrical hazards are proposed.

Jan 1, 2002

[Adams, E. R Rock Springs, Wyoming Adams, V. H. 422 East San Miguel Street, Colorado Springs, Colorado Allen, Earl W 257 Rio Grande Street, Salt Lake City, Utah Allen, Louis B . Box 1920, Denver 1. Colorado Allen, Thomas Argonaut Hotel, Denver, Colorado Alston, G. L Mine Safety Appliances Company, Pittsburgh, Pa. Ambler, J. B Box 591, Denver, Colorado Apperson, A. B. 394 Elm Street, Denver 7, Colorado Arnett, L. L. 325 North First West, Price, Utah Audin, Abel Somerset, Colorado Audin, Clement, Jr Paonia, Colorado Audin, Clement, Sr Box 627, Paonia, Colorado Audin, Ralph Box 285, Somerset, Colorado]

Jan 1, 1952

By W. J. González

"With the increasing demand for minerals, technologies to maximize mineral recovery are paramount to a mine’s economic success. Many mining process waters have the potential to form calcium-based inorganic scales, which inhibit effective mineral recovery. Often, the solution to inhibit these deposits is the implementation of a chemical antiscalant program. This paper examines the application of a fouling analyzer to continuously monitor the formation of inorganic scale in mining process streams. The fouling data can be used to compare antiscalant programs and to optimize antiscalant feedrates. Case studies validate the ability of this technology to help optimize mineral recovery processes.INTRODUCTION The mining industry uses significant quantities of water. From quarrying, to crushing, to flotation, leaching, and refining, water is often the integral motive force to move slurries, separate or agglomerate fines, and extract and purify minerals. As well, water is used in a number of ancillary applications at mines, including dust suppression, gas scrubbing, and utility processes such as boiler, cooling, and waste water operations. For many processes, the quality of water being used is inconsequential. However, for certain processes, such as flotation, leaching, and desorption / stripping, water quality plays a key role in the ability of the operation to economically recover the target minerals. Dissolved solids such as calcium and magnesium salts can concentrate in process waters, exceed their solubility limits, and precipitate as scale on metal surfaces such as feed and transfer pumps, piping, and equipment. Some of the more common scales that form in mining operations include calcium carbonate (CaCO3, or calcite) and calcium sulfate (CaSO4, or gypsum), and to a lesser extent, calcium and magnesium silicate compounds. Any scale that deposits in a process stream will negatively impact mineral recovery, and increase the operational costs of the mine site. Whether it is acid washing a scaled heat exchanger in a carbon strip at a gold operation, replacing plugged emitter tubes in a leaching operation, or hydroblasting process lines in a scrubber unit, there are costs associated with labor, cleaning chemicals, repairs, and replacement parts. These costs pale in comparison to the potential costs of downtime and lost production, should the scale deposits occur in a process that is critical to the recovery of the target mineral."

Jan 1, 2014

[Addison, Herbert Big Horn Colleries Co., Colo. Bldg., Denver, Colo. Aleshire, N. C c-o Roberts & Schaefer Co., Wrigley Bldg., Chicago, Ill. Alexander, John Dacona, Colo. Allan, David Lafayette, Colo. Allen, John Ludlow, Colo. Allen, Thomas Box 420, Glenwood Springs, Colo. Alley, Gerald C. F. &I. Co., Pueblo, Colo. Allison, ArchieBox 562, Walsenburg, Colo. Allison, D. S 1331 Roberta St., Salt Lake City, Utah Allison, Park Engineer, Standard Coal Co., Standardville, Utah Allonier, Howard R c-o Lunkenheimer Co., Cincinnati, Ohio Ambler, J. B c-o Ambler & Riter, Kearns Bldg., Salt Lake City, Utah Anderson, A. E 403 Ideal Bldg., Denver, Colo. Andrews, Sam 503 Pike Ave., Canon City, Colo.. Angster, Joe Walsen, Colo. Angus, William B. W. Snodgrass, 1575 Lafayette St., Denver, Colo. Apperson, A. B Tramway Bldg., Denver, Colo. Armstrong, C. D Apperson Vallery Co., Tramway Bldg., Denver, Colo. Arnoldi,, Victor Ideal, Colo. Autrey, J. S Perrenaud Apts., Denver, Colo. Bachman, W. H 1601 Alcott St., Denver, Colo. Bailey, R. E Utah Power & Lt. Co., Kearns Bldg., Salt Lake City, Utah Baird, Elmer A Equitable Bldg., Denver, Colo. Bartlett, G. F 311 Ernest & Cranmer Bldg., Denver, Colo. Baxter, John M 3748 Lafayette St., Denver, Colo. Becker, J. A Box 682, Rock Springs, Wyo. Beebe, John. D 1414 Court Place, Denver, Colo. Bennett, F. C Colorado Fuel & Iron Co., Berwind, Colo. Benson, Geo Cumberland, Wyo. Betcher, B. L Standardville, Utah Beuchat, Charles Pryor, Colo. Bevan,John 1625 North Corona St., Colorado Springs, Colo. Bisch, James L Van Houten, N., M. Boissier, A. H. C Boston Bldg., Denver, Colo. Bottomley, Edward Kleenburn, Wyo. Bowen, James V Union Coal & Coke Co., Colorado Bldg., Denver, Colo. Bowie, Alex R Bowie, Colo. Bowie, John S Bowie, Colo. Bowie, Wallace D Bowie, Colo. Bowns, W. J Castle Gate, Utah Boyer, F. E 631Jackson St., Denver, Colo. Boyle, Chas Sweetwater, Wyo. Brandenburger, L 59 W. Broadway, Salt Lake City, Utah Brennan, W. D Dawson, N. M. Brewster, Burt B Walker Bank Bldg., Salt Lake City, Utah Brockman, A. L Sugarite, N. M. Brooks, Ed 513 Second St., No. 1 Hill, Rock Springs, Wyo. Brown, Geo. A Cumberland, Wyo. Brown, L. E :.1212 Walker Bldg., Salt Lake City, Utah Brown, Mark Y 629 East Main St., Trinidad, Colo. Bubb, H. H Cokedale, Colo. . Bullock, W. H 1052 Gas & Electric Bldg., Denver, Colo. Bunning, P. C Rock Springs, Wyo. Burnite, Thomas B 523 Boston Bldg., Denver, Colo. Butler, T. H Hanna, Wyo.]

Jan 1, 1924

By J. Sliwinski, J. Oliveira

"The application of geometallurgy and corresponding sample selection can take on several formats within industry. Current practice can range from a strictly geostatistical approach to one in which geological and metallurgical parameters are used in combination to create a representative sample selection strategy. The stage of a project and the level of information available at the time of sampling influences the methodology used to create a representative sample.A geometallurgical study of Carpathian Gold’s Rovina Valley Project in Romania is used to demonstrate a sample selection strategy that integrates geological, mineralogical and metallurgical data to maximize the relevance of the geometallurgical unit definitions. This approach, practiced by Xstrata Process Support for its’ clients, ensures that the results of the metallurgical program can be interpreted in the context of these units.INTRODUCTIONGeometallurgy is a cross disciplinary approach in which metallurgical performance of an ore is linked to intrinsic geological and mineralogical characteristics. The objective of a geometallurgical study is to characterize the range of metallurgical performance of an orebody. This allows the geoscientist or metallurgist to create a robust flowsheet able to treat the full range in variability and to develop production strategies to maximize financial performance. The standard approach is to individually sample and test a series of ore types or geometallurgical units. Several different approaches are used in industry to define what constitutes geometallurgical units and how to sample them.One current methodology is the use of multivariate statistics. Geochemical data along with available geological data are used to define multiple variability domains (Williams, 2004; Walters, 2009). There are risks associated with this methodology since the extent of the data set itself may not support a purely statistical approach at the time that metallurgical units need to be defined. The assay suite collected by exploration programs is often limited to pay metals while metallurgical performance is often affected by ore gangue components. Furthermore, in many cases metallurgical scoping and pre-feasibility studies take place prior to the availability of extensive geochemical data sets. Purely statistical methods can produce multiple populations which require extensive sampling, testing and validation prior to consolidation into a reasonable number of composites for metallurgical testing. Methodologies are therefore required that allow representative sampling and testing of consolidated geometallurgical composites to occur at various phases throughout the development of a mining project."

Jan 1, 2013