Search Documents

By L. Echeverri

Research studies have shown that the flow within feedwells displays a vortical structure and high velocities at the locations where standard tangential inlets force its way into the feedwell swirling flow, producing high local shear rates and flow non-uniformities. These hydraulic deficiencies can be attributed to the discrete feeding through a few entrances, usually one or no more than a few tangential feedpipes, which practically project jets into the vortex within the feedwell. The main consequences are unequal flocculation with aggregates subjected to different amounts of shear and a non-uniform discharge from the feedwell. This paper presents results on the application of CFD and small-scale models to develop a new design that overcomes these problems by using an involute shaped inlet that converges around the feedwell. The result is a new feedwell with enhanced hydraulics that perfectly couples with the FLSmidth E-Duc® Feed Dilution system by protecting the flocculated aggregates that have been carefully produced upstream, and that favors uniform sedimentation conditions within the thickener thanks to a uniform discharge, while maintaining a practical and trouble-free geometry with excellent turndown.

Jan 1, 2012

By P. C. Thakur

In Part I of this paper, it was established that the width of longwall faces in highly gassy mines is primarily limited by the volume of air reaching the tail-end of the face. The ventilation air reaching the tail-end of the face should be not only enough to keep methane concentrations below the statutory limits (generally 1 percent) but also enough to prevent any gas layering. The air volume leaking from the longwall face into the gob should also be able to push the explosive methane-air mixture away from the gob area immediately behind the longwall face where active roof-fall is taking place (typically 30-45 m). The second group of variables that also controls the width of the longwall panel consists of (a) the rate of advance, (b) bleeder air quantities, (c) specific methane emissions for the gob area and, (d) efficiency and cost of gob gas capture. This paper will discuss the second group of variables and its impact on the optimum width of longwall faces in highly gassy coal mines.

Jan 1, 2009

By Kimio Itagaki, Torn Matsumoto, Makoto Ohtsuka, Kentarou Harada

"The structure and hydrogen-absorption properties of LaNis thin films were investigated in the present study. LaNis thin films were prepared by a sputtering method with a radio-frequency power, Ws, of 50 -400 Wat substrate temperature, Ts, of323 -573 K. Nickel content of the films decreased with increasing Ws, however, there was no dependence on Ts. At low Ws and low Ts, amorphous films were deposited. In other conditions, the films were polycrystalline. The films prepared at high Ws and low Ts, or at low Ws and high Ts, exhibited only a (h k · 0) peak in the X-ray diffraction profiles. This indicates that the c-axis of crystalline films was oriented parallel to the substrate plane. At high Ws and high Ts, the films with columnar structure were obtained. Hydrogen-absorption capacity of the thin films increased with increasing Ws. The pressure plateau did not appear on the pressure-composition isotherms. The films deposited at high Ts represented a higher equilibrium pressure.IntroductionThin films of hydrogen storage alloys can be applied for an electrode of rechargeable battery or fuel cell, a filter for H1 purification and various kind of sensor. Some studies on the preparation of the thin films of LaNi5 intermetallic compound, which is a typical hydrogen storage material, have been done hitherto. Adachi et al. , 2) and Sakaguchi et al. 3) prepared amorphous and crystalline LaNi5 thin films using flash evaporation of alloy powders and measured the pressure-composition isotherm for the prepared film utilizing a quartz crystal mass monitoring (QC:MM) method. It was found that the prepared amorphous film absorbed hydrogen without disintegrating into the powders and the hydrogen-absorption capacity of the films increased with the degree of crystallinity. Sakai et al. 4) reported that the maximum hydrogen storage capacities of amorphous and crystalline LaNi5 thin films, fabricated by a RF sputtering method using combination targets, were about 40 mA h g-1 (LaNisHo.7) and 160 mA h g-1 (LaNi5H2.6), respectively. Uchida et al. 5, 6) prepared LaNi5 thin films using flash evaporation of alloy powders and measured volumetrically the pressure-composition isotherm for the prepared film. It was reported that the hydrogen-absorption capacity of the films changed by the annealing treatment."

Jan 1, 1998

By Carl Havemann

[PAPER PRESENTED AT THE 8thINTERNATIONAL CORROSION CONFERENCE HELD AT THE SA NATIONAL MUSEUM OF MILITARY HISTORY, SAXONWOLD JOHANNESBURG DURING 14-15 NOVEMBER, 2006.]

Jan 1, 2006

By W. A. Calhoun

The purpose of this investigation was to develop economical mineral dressing processes for removing objectionable quantities of impurities, such as quartz and pyrite, from refractory clay deposits in east central Missouri. The presence of excessive quartz in these clays causes crazing. Pyrite causes bloating and unsightly dark blobs on the surface of fired refractory brick. The iron concentration in the proper state of oxidation may also act as nucleation centers for carbon crystal growth which can result in bursting of the refractory. Numerous deposits, representing a very large tonnage, have been examined and prospected by various refractories companies and found to contain impurities in objectionable quantities. Upgrading these clays would greatly extend our reserves of high-quality refractory clays. Wet-tabling and wet-cyclone concentration were found to be effective for removal of impurities from clays. Of the two methods, wet-cyclone concentra¬tion would be cheaper and more effective. Although wet-tabling improved the refractory properties of each clay, beneficiation by wet-cyclone produced clays of superior quality. Clay recoveries by wet-cycloning ranged from 56.1 to 81.8 percent of the weight of the crude samples, and the beneficiated clays contained from 71.9 to 94.4 percent of the total alumina. The pyrometric cone equivalent (PCE) was increased from 1 to 3 cones by wet-cycloning. The beneficiated clays also met the reheat shrinkage requirements on refiring to 1,400° C. Missouri is one of the major domestic sources of fare clay. In addition to deposits of high-grade refractory clays, there arc many deposits that contain small percentages of impurities, which render the clays unfit for the production of high-heat-duty firebrick. Development of methods to beneficiate these submarginal clays to usable materials would greatly increase commercial fire clay resources.

Jan 1, 1961

By H. S. Martin

The Phosphate Recovery Corporation operates three flotation plants, Nos. 1 and 2 concentrators about three miles northeast of Mulberry, Florida, and No. 3 plant at Wales, Tennessee. These plants represent the first commercial phosphate flotation operation and are also believed to be the largest nonmetallic flotation operation in the world at the present time. The details of this paper will be confined to plant No. 2, this being the newest and largest concentrator in Florida, and the flow sheet being practically the same as at plant No. 1. The No. 3 plant has been operated but a short time and has been shut down since December, 1932, on account of the decrease in phosphate rock production. The phosphate washers usually are located centrally on a known deposit so that about two hundred acres of ground can be mined economically to each washer location. The washers are moved to new areas when the distance becomes too great for economical pumping. The flotation plants are built either adjacent to a washer, so that current debris may be utilized, or on the site of a former washer where there is sufficient accumulated debris available for mining, and the flotation plants must also be moved from time to time. Most of the water used in the Florida flotation plants is recovered after passing through a circulating system where most of the fine suspended matter is settled out, but some make-up water is obtained from deep wells near the plant. Power is obtained from the Tampa Electric Co. through the distribution facilities of the International Agricultural Corporation. Flotation concentrate is hauled from the plant by trolley over the International Agricultural Corporation's trolley system, to the drying plant at Prairie, one mile northwest of Mulberry. Ore Treated In the pebble phosphate district of Florida, the phosphate mineral, or collophane, is usually found in horizontal beds of varying thickness

Jan 1, 1935

Because of complex geological environments, a number of coal reserves occur in inclined or dipping coal seams in certain parts of the world. Longwall top coal caving using split-level a singleentry panel system (SSPS) has been widely used for extracting such coal seams with large thicknesses (greater than 6 m) in China because SSPS can reduce or mitigate problems of coal outbursts, gate road deformations, overturning of shields, downhill sliding of shearer and armored face conveyor (AFC), and so forth, during mining of inclined coal seams. Depth of yield is the range of yield coal from the rib of the pillar to the boundaries where yield ends. It plays a significant role in maintaining the gate pillar stability. This paper presents a study on the stability of an unconventional water-obstruction gate pillar (UWGP) formed by SSPS to prevent water inrush in mining of an inclined thick coal seam in a coal mine in China. As the shape of this pillar is non-cuboidal, nonparallelepiped, a conventional empirical or analytical method is not applicable for studying its stability.

Jan 7, 2020

By Larry Joe Linley

The Department of the Interior, Bureau of Mines is reviewing explosion protection methods for use in gassy coal mines. This performance criteria guideline is an evaluation of three explosion protection methods of machines electrically powered with voltages up to 15 000 volts AC. A sufficient amount of basic research has been accomplished to verify that the explosion-proof and pressurized enclosure methods can provide adequate explosion protection with the present state of the art up to 15 000 volts AC. The routine application of the potted enclosure as a stand alone protection method requires further investigation or development in order to clarify performance criteria and verification-certification requirements. An extensive literature search, a series of high voltage tests, and a design evaluation of the three explosion protection methods performed at White Sands Test Facility indicates that the explosion-proof, pressurized, and potted enclosures can all be used to enclose up to 15 000 volts AC, if the performance criteria and verification-certification requirements recommended in this guideline are implemented.

Jan 1, 1982

By G. Thom, A. Kay, J. B. Hyde

"This paper will initially outline the specific types of copper castings used in blast furnace iron production. Tuyeres, tuyere coolers and stack cooling plates will be discussed in some depth, with particular reference to their dimensional configuration and purpose.Following this, the failure of such cooling members will be discussed, with special focus on tuyeres. Tuyeres are the most common casting which often requires replacement. Reasons for failure and its effect on operations will also be included.The latter sections of the paper will deal with the strict specifications demanded by ironmakers regarding copper castings. The justification for such rigid demands will be explained through the material presented earlier in the paper.IntroductionThe modern 5000-tpd blast furnace, worth millions, is a large capital investment to be sitting idle. Consequently, ironmakers strive to minimize the loss in iron production and revenue from furnace downtime. Two major causes of downtime are furnace relines and shutdowns to replace damaged tuyeresor tuyere coolers. Copper ancillaries are important items in the production of iron. They are consumable items, therefore they contribute to the campaign life or to the downtime in blast furnace production.Several combinations of lining and cooling systems have been used with varying degrees of success. Blast furnace refractories have evolved from ceramic to carbonaceous linings. The Russians and Japanese have successfully introduced stave-cooled furnaces that may have several forms, such as evaporative cooling. Stelco has two furnaces which use the Russian-designed cast iron system. However, this paper will be confined to the use of copper cast cooling members in a conventional internally cooled furnace.Figure 1 is a schematic cross section of the E blast furnace. The three major sections of a blast furnace-the stack, bosh and hearth-are identified. Further, the locations of the various copper members are indicated. This furnace produces an average of 5300 tons of hot metal per day."

Jan 1, 1982

By N. W. Lord

The process of molten-zone refining is analyzed for long ingots and many zone passages. Formulas are derived which give the resultant impurity distribution in terms of finite series. A comparison with the approximate procedure of Hamming is given. HE physical principles and applications of an extremely physicalprinciple efficient form of metallurgical refinement has been described by Pfann. The purpose of the present paper is to describe a method of analyzing exactly the particular program used which enables the segregation effect to be predicted for any number of molten-zone passages in a long ingot. The method is applied to the particular case of refinement of an ingot whose impurity initially is uniformly distributed throughout its length. A number of molten zones of equal length are passed through the ingot effecting a radical redistribution of impurity. Pfann has indicated an approximate method, due to R. W. Hamming, of calculating the resultant concentration after each successive zone pass for a particular value of the segregation constant defined in his paper. Here a solution will be presented in terms of the number of zone passes and the segregation constant. The expression, though cumbersome, is exact and susceptible to ordinary numerical computation procedures. The results of a similar computation using the procedure of Hamming are presented in a table together with the exact results of the present method. The discrepancy in terms of absolute concentrations is tabulated for the first eight zone-lengths. To establish the notation (which follows that of Pfann1 as closely as possible) and physical basis of the analytical equations, the physical model and principal assumptions may be reviewed. An alloy of two elements, where there is formed a continuous range of solid solutions, usually does not melt as a simple compound. Rather, a temperature is reached where the solid solution is in heterogeneous phase equilibrium with a liquid solution of different composition. The temperature dependence of these equilibrium compositions forms part of the phase diagram. For very small concentrations of a solute B in a solvent A, this usually takes the form of Fig. 1. Sometimes the solidus and liquidus slope upward. This corresponds to a segregation constant (defined below) which is greater than unity. The segregation constant is now defined as k = Cn(x)/CnI(x) [1] where C,,(x) is the impurity concentration in the solid ingot at distance x during the nth passing of a molten zone and Cnl (x) is the impurity concentration of the liquid zone from which the solid at dis- tance x is formed (see Fig. 4 of ref. 1.) C (x) remains the same after passage of the zone. The constant k may be either greater or less than unity in general. Purification in the former case is effected only in a finite ingot and in the portion that is melted last. For k less than unity purification is effected even in an infinite ingot. The method which follows gives, in the former case, the successive increases in impurity concentration and, in the latter case, the successive decreases in concentration. The general case of impurity redistribution will be considered first, and purification will be discussed later on. The analysis rests on the following assumption: The movement of the zone is too rapid to allow appreciable atomic rearrangement in the solid sections and too slow to disturb the uniform impurity distribution in the liquid zone characteristic of equilibrium. Hence, the composition in the solid at the left solidifying interface will be determined by Eq. 1 while the impurity concentration of the liquid zone will be uniform throughout its length. The reasoning which follows closely parallels that of Appendix 11 in Pfann&apos;s paper. It is reviewed here for the case of the nth zone pass in order to make clear the meaning of an operator essential to the present method. Fig. 4 of ref. 1 shows the movement of a molten zone of length 1 in an ingot of total length d. Each Cn(x) can be determined from the condition that the amount of solute added to the zone during an incremental advance, dx, is due to the melting in of a solid portion C(x)dx and the freezing out of kCnl(x), that is d I —r- CnL (x) dx = Cn-1 (x+l)- kCnL (x) dx or, in terms of Cn(x) d k k —— C,(x) +—c.(x) =— Cn-1 (x + l). [2] dx l l This, of course, is derived from the main assumption, the fact that 1 is constant, and that the total impurity content previously present up to x + 1 is constant . A correction has to be made for the region (d — nl) < x < d. This is due to the zone length changing during the passage of the solidifying interface beyond x = d — 1. Since the general solution would be too complicated otherwise, only the region 0 < x < d — nl is considered. The general solution of Eq. 2 is

Jan 1, 1954

By Alejandro Ferrada Vergara

Most blasting techniques that are designed to improve fragmentation and subsequently improve ore work index to downstream comminution processes, apply powder or energy factor increases, either by stretching the drilling pattern (burden/spacing ratio) implementing faster initiation sequences or using more energetic explosives. The new application will move detonation parameters up, making the blasting process riskier for the surrounding boreholes, explosive column or initiation systems functioning.

Jan 1, 2016

By K. Donahue

Clay minerals play an important role in the gravitational stability of man-made rock piles by affecting geotechnical and hydrological characteristics of the material. The Goathill North rock pile at the Questa Mine in northern New Mexico has been the focus of a multi-disciplinary study to determine the effect of weathering on rock pile stability and in particular to determine if clay minerals are forming in the rock pile due to surface weathering. The results of x-ray diffraction (XRD) and scanning electron microscopy (SEM) analyses indicate the clay minerals found within the fine-grained soil matrix of the rock pile are of hydrothermal origins and did not detect any neoformation of clay minerals. The foremost mechanism for an increase in clay minerals within the rock pile is the physical break down of hydrothermally altered rock fragments to release hydrothermal clay minerals. The hydrothermal clay minerals within the rock pile show evidence of weathering by the dehydration of smectite from 2-water to 1-water interlayers within the clay mineral structure. This dehydration is most likely due to higher temperatures and low relative humidities in the Goathill north rock pile during surface exposure.

Jan 1, 2009

The Institute assembled in the metallurgical lecture-room of Pardee Hall, Lafayette College, at 7 o&apos;clock P.M. on Tuesday evening, October 21st. The session was opened by the President, R. W. Raymond, with an address on Mining Industry as illustrated at the Vienna Exposition. The second session was held on Wednesday morning. The Council reported the following names for election as members and associates. They were unanimously elected. Ayres, W. S.,.......Easton, Pa. *Baker, Prof. A. L.,.. Easton, PR. Browne, Thomas Nicholl,.... Hamilton, Nev. *Carter, Frank,......Pottsville, Pa. *Davis, E. F. C.,... Pottsville, Pa. *Fox, Prof. J. G.,...,..Easton, Pa. *Haight, Ogden,...Etna, Pa. Hall, Norman,...Sharon, Pa. *Knap, Joseph,......Fountain Mill, Pa. Miller William McKeen,.... Easton, Pa. Pardee, I. P.,....Easton, Pa. *Plater, John E.,......Eureka, Nev. *Platt, Joseph L., Jr.,.....Franklin Furnace, N. J. *Plumb, W. H.,......Mauch Chunk, Pa. *Reis, George L.,......New Castle, Pa. *Samuel, Edward,. ..Philadelphia, Pa. *Smith, William Allen,.....Trenton, N. J. *Smock, Prof. John C.,..... New Brunswick, N. J. *Weberling, Charles,.....Salt Lake City, Utah. Also the following as foreign members: Beaulieu, Ad. le Hardy de,. . Brussels, Belgium. Beaumont, Major Fred.,..London, England. Beck, Alexander,.Mons, Belgium. Bodmer, J. J.,..London, England. Brassert, Berghauptmann, Dr.,. .. Bonn, Prussia. Brogden, James,.London, England.

By Martin R. E

L44 Shaft is a major upcast ventilation shalt in the hanging wall of the 1100 Orebody. Various techniques for stripping a raisebored pilot hole were combined to produce L44 shaft. From the surface to 198 m depth, the shaft was concrete lined 7.3 m internal diameter. Below this the shaft was developed to 7.6 m diameter unlined. 11 level, 540 m below the surface, was the first readily accessible level connection. The section to 198 m depth was benched and concrete lined through weak oxidised ground. When more competent ground was encountered the operation was converted to horadiam stripping. This application of the raiseborer has led to a safer, more efficient method of shaft development.

Jan 1, 1977

By Pengfu Tan

The control of converter slag chemistry and slag viscosity has played an important role in optimizing converter operations. A thermodynamic model of copper P-S converter and a viscosity model of converter slag have been used to predict the chemistry and viscosity of converter slag. The effect of oxygen potential, SiO2/Fe in slag, detection of slag blow endpoint, and temperature on slag viscosity, liquidus temperature of converter slag and skimming operation has been discussed. Some applications of the industrial operations have been presented.

Jan 1, 2006

By G T. Kukla

A Seam deposit User oriented Mine Planning System (SUMPS) was developed by The Broken Hill Proprietary Company Limited (BHP) at its head office in Melbourne. It is one of the computer mine planning systems developed by the Corporate Data Processing (CDP) section of BHP. To date it has been employed in the feasibility study of four coal prospects for the BHP Group, including Gregory in central Queensland û Ham and Van Hoorn (1978). It was also used in detailed short term mine planning for Gregory. A recent application was in the feasibility study of Saxonvale, a multi seam coal deposit in New South Wales with seams up to 20 m thick. The other two applications of SUMPS were also on thick multi seam coal deposits. Development of programs for the underground subsection of SUMPS is continuing. SUMPS was developed and implemented on mini computers with graphics and plotting peripherals. The company&apos;s philosophy towards computing is one of centralized development and project planning, with transfer of hardware and software to site once the mine becomes operational. Support of the site&apos;s system continues from head office which is continually involved in development of SUMPS and issuing revision updates to sites. The users, as well as programmers, were mostly geologists and mining engineers. This helped to ensure rapid, successful implementation. The broad approach of this system was to use interactively the specialist skills and interpretative abilities of the user mining engineers and geologists with the data manipulation abilities of the computer. It is an integrated system which covers geological exploration, deposit modelling, mine planning and production scheduling. An important feature of the system is that the user has full interactive control over each function through a graphics terminal where applicable.

Jan 1, 1980

By Donald Thompson, Jessie Bonner, Ileana Tibuleac

Predicting ground motion from complicated mining explosions is important for mines developing blasting programs in regions where vibrations must be kept below certain levels. Additionally, predicting ground motion from explosions in complex 3D media is important for source size estimation for nuclear treaty monitoring. Both problems have been addressed under the development of a new series of programs including: 1) Generalized Fourier Methods to generate synthetic seismograms (Green’s functions) in 3D media for a moment tensor source implementation and 2) MineSeis3D, a program that simulates seismograms for delay-fired mining explosions with a linear relationship between signals from small size individual shots. To test the programs, three-component seismic recordings of three production shots at an iron mine in northern Minnesota were compared to synthetic waveforms in 3D media. Comparison of the observed and synthetic waveforms shows promising results. The shape and arrival times of the normalized synthetic and observed waveforms are similar for most of the stations. The synthetic and observed waveform amplitude fit is best for the vertical components in the mean 3D model but not as promising for the transversal components. The observed effect of spall on the waveform spectra was weak in the case of fragmentation delay-fired mining explosions. Commercial applications of the code could provide data needed for designing explosions that do not exceed ground vibration requirements posed by the United States Department of Interior, Office of Surface Mining.

Jan 1, 2005

By B. Anameric

The pig iron nugget process is gaining in importance as an alternative to the traditional blast furnace. Throughout the process, self-reducing?fluxing dried greenballs composed of iron ore concentrate, reducing-carburizing agent (coal), flux (limestone) and binder (bentonite) are heat-treated. During the heat treatment, dried greenballs are first transformed into direct reduced iron (DRI), then to transition direct reduced iron (TDRI) and finally to pig iron nuggets. The furnace temperature and/or residence time and the corresponding levels of carburization, reduction and metallization dictate these transformations. This study involved the determination of threshold furnace temperatures and residence times for completion of all of the transformation reactions and pig iron nugget production. The experiments involved the heat treatment of self-reducing?fluxing dried greenballs at various furnace temperatures and residence times. The products of these heat treatments were identified by utilizing optical microscopy, apparent density and microhardness measurements.

Jan 1, 2007

By B. McFadzean, P. E. Ngoepe, P. P. Mkhonto

"The theoretical technique of computational modeling and the experimental determination of the enthalpy of adsorption of a ligand molecule onto a mineral surface deliver the same output parameters and, therefore, complement each other in investigating the affinity of different ligand types for mineral surfaces.This study ran parallel experimental tests and computational calculations to determine the enthalpy of adsorption of a series of increasing chain length xanthates onto a pyrite surface. The outcomes showed that, while the absolute energy values were different, the trends were similar. Both computational and experimental approaches showed that the extent of the interaction of the xanthate molecule increases with increasing carbon chain length. The computational values were larger than the experimental values, which could be explained, in part, by the addition of water to the computational system, which resulted in a decrease in the heat of adsorption on the (100) surface, compared to the adsorption of the collector in a vacuum. The computational method showed that, in the case of the pyrite (100) surface, the most exothermic reaction was obtained when the two xanthate sulfur atoms bridged two pyrite 5-coordinated iron atoms. The (111) surface was found to be more reactive and different adsorption mechanisms were predicted for each of the C2, C3, C4 and C5 chain length xanthates.The experimentally determined exothermic increase in heat of adsorption for the addition of each CH2 group was found to be -8.17 kJ/mol. The contribution of the thiol head group was -34.9 kJ/mol. Previous studies on self-assembled monolayers have shown that these values are compatible with lateral interactions between CH2 groups and the exclusion of water. This study provides a rigorous experimental and computational approach which is intended to afford confidence in modelled data for the screening of new ligands for flotation processes.INTRODUCTIONComputational modelling is a fast and cost-effective method of screening collector molecules for the efficacy of their adsorption onto mineral surfaces. However, it is desirable to measure the computational outputs against experimental outputs to check for congruency. Computational modelling and experimental microcalorimetry both deliver the same output parameter: the energy of adsorption of the molecule onto the solid surface. These techniques are therefore ideally suited to complement one another in investigating the affinity of the interaction between collector molecules and mineral surfaces."

Jan 1, 2018

By Y. Tanaka, M. Maeda, S. Suzuki, C. Tokoro, T. Kato, K. Muto

Boron (B) co-precipitation was investigated with ettringite to establish a cost efficient method of removing B from acid mine drainage. For 25 mg/L of B solution, most appropriate pH for B removal was pH 11.5. The most appropriate amount of reagent for B removal within Japanese effluent standard (10 mg/L) was B:Al:Ca:SO4 = 1:3:9:4.5, which corresponds to the composition of Ettringite (Al:Ca:SO4 = 2:6:3). The effect of silicate, carbonate and temperature on efficiency of B removal is important as groundwater and hot spring water are often contaminated. When silicate and carbonate are present, more Al and Ca salts are needed for B removal since some aluminum and calcium precipitate with silicate and carbonate as kaolinite and calcium carbonate. These precipitates do not contribute much to B removal. As the temperature raised, the most appropriate pH for B removal decreased. B removal became less efficient as monosulfate precipitated more rapidly as ettringite.

Jan 1, 2015