Search Documents

By Howard P. Hamlin

This Bureau of Mines report is concerned with the testing procedures for evaluating clays, shales, and slates for lightweight aggregates using the rotary-kiln method of production. To meet the increasing demand for light-weight concrete, rapid, accurate methods for appraising raw materials for light-weight aggregate are needed. Preliminary tests were made on samples of clay, shale, and slate, using laboratory equipment, and the data were used to establish operating conditions for pilot-plant-size rotary-kiln tests. Lightweight concrete was made from the processed aggregates and the properties determined. The results show that the laboratory data can be used to guide rotary-kiln testing, and, with the exception of sampling, a complete appraisal of a raw material for lightweight aggregate concrete can be made in 3 days by the methods described in this report.

Jan 1, 1962

Modelling Channel Scale Flow in Heap Leaching Using Smooth Particle Hydrodynamics (SPH)

Sep 13, 2010

By A. Singh

The control of flotation plants is by no means trivial. Flotation is one of the most interactive minerals? processing operations. The interactive nature of flotation circuits results in oscillations of levels and hence of grades and recoveries. Also, poor level setpoint tracking and disturbances have negative influences on grades and recoveries. The result is an unstable plant with limited scope for optimization. An advanced controller, FloatStarTM, has been developed to provide tight control and to reduce the amount of disturbances in flotation levels. It has been shown on a number of plants that the system results in faster and better setpoint tracking, better regulatory control and faster settling times after start-ups and disturbances. The successful stabilization provided by FloatStar has made it easier to investigate the area of optimization on flotation circuits. Mintek has identified the need for a more meaningful set of setpoints or aeration rates to use as a basis for control than levels and have advocated flow control by looking after residence times. When the feed conditions change, the ideal solution would be an algorithm or strategy that finds the new optimum conditions rather than just having an unguided hunt from the previous point. A multivariable flow-optimizing algorithm, a new module in FloatStar, has been developed to calculate optimum level setpoints and/or aeration rates that will aim to optimize the residence times, mass pulls and circulating loads within a flotation circuit. Keywords: flotation, regulatory, FloatStar, start-up, disturbance, residence times, circulating loads

Jan 1, 2003

By Marius Jacobs

"Safety performance in many companies and even industries has stalled in the few years. Accidents rates are at a "plateau" and yet, serious accidents and fatality rates are not. In more dramatic cases, such as in the BP Texas disaster, organizations that have "exemplary" safety statistics, suddenly have a catastrophic or multi-fatality event occurring. Other classic examples are the Piper Alpha disaster and NASA’s Challenger and Columbia disasters and even the Chernobyl nuclear reactor. Looking into the root causes of these accidents provides an insight into the events and deficiencies that led up to the accident, but what are the common features in the organization’s mindset? What characterizes these organizations’ decision-making, their approach to safety and to risk and are there specific cultural features that can be delineated? The research and review presented in this paper covers a period since 1994, which started in the Australian resource industry and since then covered international events. The features of these organizations are summarized as the seven deadly delusions, based on extensiveresearch since 1997 of organizations that suffered unexpected disasters.The Piper Alpha Oil Rig disaster in the North Sea, on the 6 July 1988, was one of the most pivotal events in safety around the world. It changed the thinking and focus of governments, whole industries and led to numerous books and papers. It resulted in new legislation, textbooks and a critical self-examination by the oil and gas industry.In short, an explosion and fire occurred when a pipe started leaking gas and ignited. A temporary flange, with no safety valve, was used to block off this pipe during a maintenance operation the previous shift. The permit to advise operators not to start the pumps on this line was misplaced and lost. Several deficiencies, problems and system failures coincided. A key factor was that the water deluge system was inoperable at the time and failed to extinguish the large fire that erupted, followed by an even larger gas explosion. The accommodation unit, situated on top of the oil rig, was the main "killing field" - most men gathered here to await instructions (which never came) and where they died from smoke inhalation. Later, a large explosion of the gas pipeline from an adjoined rig exploded and killed more people.The line of events and the associated system failures are all very relevant in the analysis of the accident, and provide the only insight into what caused the accident. But much "further back", inside the organization’s culture, lurks more dark matter. The first inclination is to ask what was "deficient" in the culture. Did they not care enough about safety, or about their people? Did they have a culture where production decisions were more important than safety considerations? Did they ‘coerce’ supervisors and employees to ignore safety precautions or did they just "fly by the seat of their pants"?Not surprisingly, it is very difficult to identify the true nature of the culture in that business because in such an aftermath of death and destruction, no one dare say that the safety culture was a ‘positive one, focused and caring’ or that the company was doing well in safety and that this is only a freak accident. Indeed, there were many deficiencies in the organization’s systems and procedures, such as the permit to work system.But there are some niggling questions: How is then that the Piper Alpha Oil Rig was actually considered the company’s most productive and safest oil rig in the North Sea? Why would this rig win a safety competition, 6 months before the disaster, with the deficient permit as its most outstanding successful system?"

Jan 1, 2014

By T. F. Anstett

The Bureau of Mines estimated the potential availability of tungsten from 57 mines and deposits in 19 market economy countries. The tungsten resources of China and the U.S.S.R. were also estimated. This resulted from an evaluation of tonnage-cost relationships indicating the quantity of tungsten available as ammonium paratungstate (APT), artificial and natural scheelite, and ferrotungsten at various average total costs of production including 0- and 15-pct rates of return on invested capital. The evaluated deposits contain 1.2 million metric tons (t) of recoverable WO3, of which approximately 52,000 t of AEYT can be produced at the January 1983 market price of $5.37/lb, 89,000 t of natural and artificial scheelite at a market price of $3.63/lb, and 1,700 t of ferrotungsten at $5.61/lb of tungsten. An annual availability analysis indicates that by the early 1990's new deposit discoveries, development of known prospects, or expansions of producing mines will be necessary to meet projected tungsten demand.

Jan 1, 1985

C. R. CORNING, Chairman. ADOLPHE E. BORIE, First Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. Vie-Chairmen. JOHN H. ALLEN, GEORGE M. COLVOCORESSES, RICHARD M. ATWATER, JR., ROBERT PEELE, GEORGE D. BARRON, CHARLES P. PERIN, A. CHESTER BEATTY, JOSEPH A. VAN MATER, J. PARKE CHANNING, ARTHUR L. WALKER. D. C. Bard, Howard Eckfeldt. Philip N. Moore, W. de L. Benedict, R. C. Gemmell, T. H. O'Brien, John C. Branner, F. Louis Grammer, James J. Ormsbee. Palmer Carter, Ernest A. Hersam, Edward W. Parker, Allen J. Clark, Edwin C. Holden, John B. Porter, F. Crabtree, William L. Honnold, R. DI. Raymond, George G. Crawford, Reginald E. Hore, Robert H. Richards, O. C. Davidson, C. Colcock Jones, LeRoy Slash, E. V. D'Invilliers, Eugene P. Kennedy, Frederick H. Sexton, James S. Douglas, Chester F. Lee, Henry L. Smyth, Walter Douglas, Richard S. McCaffery, F. W. Traphagen, Howard N. Eavenson, James F. McClelland, Elton W. Walker. Milton H. McLean, The Chairman of the Committee on the eve of his departure frog -,he country for an extended stay, addressed the following letter t ,he President of the Institute NEW YORK, N. Y., APRIL 19, 1913.

Jan 5, 1913

By Z. H. Zhou

It is difficult to remove cadmium from raw indium using only electrolytic refining because their standard potentials are similar. In this paper, physical and chemical methods were used to remove Cd from raw indium. Indium metal is vacuum refined for two hours at 400°C with a vacuum pressure of 20 Pa. In this process, 99.70% of the Cd can be removed. The removal rate of Cd reaches 90% to 95% when indium is further smelted for 10 minutes in a 20% glycerin solution of KI and I2 at 180°C. When pre-indium is electrolytic refined in an In2(SO4)3-H2SO4 system, in which the indium content is 80 to 100 g/L, the pH is 2.0-3.0 and the current density is 80 to 100 A/m2, the contents of the impurities decrease and the purity of the indium product reaches 99.99%.

Jan 1, 2007

By David Newman

Multiple seam underground coal mining is ubiquitous in Appalachia. Many coal properties have from two to ten or more economically mineable coal seams. Because of the ability to penetrate 600-feet to 1,000-feet or deeper into the mountainside leaving panels of web pillars separated by barrier pillars, highwall mining is a hybrid between surface and underground mining. As a result, many of the ground control problems commonly associated with multiple seam underground mining exist with multiple seam highwall mining. These include: i) superjacent mines, subsidence and caving propagating to overlying seams and ii) mines, pooled water and the potential for inundation resulting from a iii) breakthrough between an active highwall mine and abandoned underground mines in the same or superjacent seams, the presence of overlying or underlying mine workings where iv) pillar columnization in the active mine is not possible, and v) the question of whether to mine ?top-down? or ?bottom-up.? Case histories are presented from southeast Ohio where the Middle Kittanning No. 6 and Lower Kittanning No. 5 seams are successfully highwall mined with 20-feet to 40-feet of largely shale interburden. A highwall miner was caught in a highwall collapse in the Middle Kittanning No. 6 seam when it was overmining auger workings in the Lower Kittanning No. 5 seam. Multiple seam interaction caused by the overmining transferred overburden stress onto the Lower Kittanning No. 5 seam. The overburden concentrated through web pillars initiated auger web pillar failure, resulting in roof collapse and subsidence in the Lower Kittanning No. 5 seam that propagated up to the Middle Kittanning No. 6 seam. A second case history involves multiple seam highwall mining in southeast Kentucky. The A3 Rider, A3, B2, and C1 seams are being highwall mined around abandoned underground mines in the A3 and B2 seams and augering in the A3 Rider. Because of spoil storage constraints for the surface contour mines, the highwall miner follows the active pits in each seam so a standard sequence of ?top-down? or ?bottom-up mining does not exist. The planning and engineering design considerations associated with each case history is presented along with geotechnical information. In the case of the highwall collapse a back analysis is presented of the stability and safety factors for the auger webs, highwall miner web pillars, and barrier pillars.

Jan 1, 2009

By Neil E. Ryan

Because of their chemical reactivity and affinity for oxygen, rare-earth elements are difficult to extract, and due to their close chemical similarity, it is an exacting task to separate one from the other. Nevertheless, these same characteristics can be used to benefit other metals by enhancing their resistance to high-temperture oxidation/corrosion and by inhibiting their corrosion in aqueous environments. This paper gives an overview of the use of rare-earths: [a] as alloy additions, [b] in coatings, and [c] when added to hostile environments, to retard rates of high- temperature oxidation and inhibit aqueous corrosion.

Jan 1, 1992

By M. R. Yalamanchili, J. D. Miller

Discussion by M.R. Yalamanchili and J.D. Miller The authors, M. S. Celik et al., should be recognized for their efforts to describe the flotation behavior of boron minerals. In the case of borax and other soluble salt minerals, analysis of the flotation chemistry has been difficult because of the high ionic strengths associated with these soluble salt systems. However, considerable progress has been made in this area, and recently a surface charge/collector colloid adsorption model was proposed by Miller and his coworkers to explain the collector adsorption phenomena observed in soluble salt flotation systems (Milleret al, 1992; Yalamanchili et al., 1993; Miller and Yalamanchili, 1994; Yalamanchili and Miller, 1994a: Yalamanchili and Miller, 1994b). In this work, the sign of the surface charge of alkali halides in their saturated brines was established on the basis of nonequilibrium electrophoretic mobility measurements by laser-Doppler electrophoresis (Miller et al., 1992). Generally, these results are what would be expected from the simplified lattice-ionhydration theory. This electrokinetic information coupled with the stability and prevalence of collector colloids in such soluble salt flotation systems indicates that the selective flotation of alkali halides is due to the adsorption of oppositely charged collector colloids by heterocoagulation. Experimental flotation/bubble attachment results for 21 different alkali halides (Yalamanchili et al., 1993; Yalamanchili and Miller, I994b) confirmed that the flotation response of soluble salt minerals with weak electrolyte collectors can best be explained by the adsorption of oppositely charged collector colloids rather than by the adsorption collector ions and/or neutral molecular dipoles as originally suggested by many researchers (Fuerstenau and Fuerstenau, 1957; Schubert, 1967; Roman et al., 1968). In addition, the flotation of certain alkali oxyanions (Pizarro et al., 1993) and double salts such as schoenite and kainite can be explained by the same collector colloid adsorption mechanism (Miller and Yalamanchili, 1994). The borax flotation results reported by Celik et al. need to be examined in terms of the above mentioned surface charge/ collector colloid adsorption model. Unfortunately, the authors seem to be unaware of this recent work that nicely describes soluble salt flotation with weak electrolyte type collectors such as amines and carboxylates. In view of our past work, the flotation characteristics of borax were of particular interest, and, in this regard, the results of dodecyl amine flotation of borax reported by Celik et al. have been examined in further detail in the light of experimental results from our laboratory. In our research, a vacuum flotation technique was used to study the flotation response of borax (Na2B407.10H20), which has a solubility of 39 g/L at 25 °C) with dodecyl amine hydrochloride as collector. These chemicals were purchased from Eastman Kodak and used as received. Saturated solutions of borax at desired pH values were prepared by continuously stirring the salt solutions over a period of about 10 hrs. It should be mentioned that the conditioning time to achieve equilibrium is an important variable and can significantly change the flotation response of some soluble salts (Yalamanchili et al., 1993). Collector was added to the saturated borax solutions containing about one gram of 100x 150 mesh borax particles, and conditioning was done for about 20 minutes prior to flotation. The borax flotation recoveries from saturated brine are presented in Fig. 1 as a function of collector addition at the natural pH of 9.3, as reported both by Celik et al. and as measured in our laboratory. In addition, the region of precipitation for the dodecyl amine hydroborate is included in Fig. 1. It can be seen in Fig. 1 that the flotation response curves are separated by about one order of magnitude in R12NH3CI collector addition. The flotation results of Celik et al. show that the maximum borax recoveries can be obtained below the solubility limit of the dodecyl amine hydroborate collector. However, in our experiments borax flotation seems to occur only after the precipitation of the dodecyl amine hydroborate collector as might be expected from the collector colloid adsorption model (Yalamanchili et al., 1993) if borax were negatively charged. Further analysis by nonequilibrium and equilibrium electrophoretic mobility measurements for borax indicates that borax is negatively charged at the natural pH of 9.3, as discussed below. The reliability of the nonequilibrium electrophoretic measurements has been demonstrated previously for alkali halides and alkali oxyanions (Miller et al., 1992; Miller and Yalamanchili, 1994). The equilibrium and nonequlibrium electrophoretic measurements for borax were found to be consistent and are presented in Table 1. These results provide clear evidence that borax carries a negative surface charge in its saturated brine (pH 9.3), and the sign of the surface charge of borax reverses and becomes positive if the pH is reduced to 8.6. The equilibrium between borax and its saturated brine can be described by the following reaction: [2Na2B407.1OH2O-4Na++B407=+HB4O7 +OH+19H20] It appears that the oxyanions of the borax lattice provide

Jan 1, 1995

By Larry F. Drolet

Charleston, SC is anything but boring. The city was founded in 1670 and has played a significant role throughout the history of the United States. Located along the coast of the Atlantic Ocean in the southeastern United States, Charleston was a vital city in America?s early existence. Charleston?s coastal location has helped the city become the fourth largest cargo port in the United States and earn the 2011 designation as the number one travel destination in the United States by the Conde Nast Traveler Magazine. Part of Charleston?s charm and beauty can be attributed to its historic structures and churches that line nearly every sidewalk, roadways that were laid out based on the width of horse carriages, great weather, southern hospitality and coastal living. Now imagine the challenges of installing new, or re-placing aging infrastructure, in this setting. Every shovel full of dirt, every stick of pipe and every roadway sub-surface has its own historic story to tell. For engineering minded individuals, Charleston?s infrastructure has almost as fascinating a history as its more visible surface structures. Charleston was among one of the first American cities to construct separate sanitary and storm water drainage infrastructure. This concept has roots dating back to the city?s founding and is a credit to the foresight of its founding fathers who understood the basic health differences between sanitary and storm water.

Jan 1, 2013

By Gary B. Petersen

The author has developed a seven-step process called the Applied Rock Mechanics (ARM) Protocol that the author has used to solve numerous roof stability problems in mines throughout North America since 1975. It is a practical evaluation process using trained observation, innovative data collection instrumentation, video borehole cameras, analytical processes, and controlled testing methods that have become highly effective in solving ground control problems in every type of underground mine. This paper will describe each of the steps of the protocol and how the rock mechanics engineer applies them to resolve a typical ground control problem.

Jan 1, 2012

By Herly Alcázar

El presente trabajo describe el proceso de optimizacion en la fundición de precipitados de oro y plata en la refinería de la mina Pierina a través del control de los diversos parámetros que involucra dicho proceso. Para ello, se trabajó con composiciones ternarias cercanas al punto peritéctico y asi procesar adecuadamente el tipo de precipitado. Entre sus principales logros de optimización tenemos: el incremento de oro y plata, el rendimiento de los crisoles, la reducción de los costos por consumo de reactivos y el mantenimiento de la calidad del precipitado.

Sep 13, 2001

By N. R. Morrow, C. C. Harris

The experimental points which describe capillary pressure curves are determined at apparent equilibria which are observed after bydrodynamic flow has ceased. For most systems, the time required to obtain equalization of pressure throughout the discontinuous part of a phase is prohibitive. To permit experimental points to be described as equilibria, a model of capillary behavior is proposed where mass transfer is restricted to bulk fluid flow. Model capillary pressure curves follow if the path described by such points is independent of the rate at which the saturation was changed to attain a capillary pressure point. Aemodified suction potential technique is used to study cyclic relationships between capillary pressure and moisture content for a porous mass. The time taken to complete an experiment was greatly reduced by using small samples. INTRODUCTION Capillary retention of liquid by porous materials has been investigated in the fields of hydrology,l soil science,2 oil reservoir engineering,3 chemical engineering," soil mechanics,5 textiles: paper making: and building materials In studies of the immiscible displacement of one fluid by another within a porous bed, drainage columnsl and suction potential techniques2 have been used to obtain relationships between pressure deficiency and saturation (Fig. 1). Except where there is no hysteresis of contact angle and the solid is of simple geometry, such as a tube of uniform cross section, there is hysteresis in the relationship between capillary pressure and saturation.2 The relationship which has received most attention is displacement of fluid from an initially saturated bed (Fig. 1, Curve R2), the final condition being an irreducible minimum fluid saturation Swr. Imbibition (Fig. 1, Curve A), further desaturation (Fig. 1, Curve R), and intermediate scanning curves have been studied to a lesser but increasing extent.2 ,3,9-12 This paper first considers the nature of the experimental points tracing the capillary pressure curves with respect to the modes and rates of mass transfer which are operative during the course of measurement. There are clear indications that the experimental points which describe these curves are obtained at apparent equilibria which are observed when viscous fluid flow has ceased; and any further changes in the fluid distribution are the result of much slower mass transfer processes, such as diffusion. Unless stated otherwise, this discussion applies to a stable packing of equal, smooth, hydrophilic spheres supported by a suction plate5 with water as the wetting phase and air as the nonwetting phase. The discussion can also be applied, in many

Jan 1, 1966

By D. B. Sikka, R. B. Bhappu

Porphyry-type copper-molybdenum (Cu-Mo) deposits typically occur in the Phanerozoic rocks and have been well-documented. During the past two decades, a number of porphyry-type Cu-Mo deposits that range in age from 1055 Ma to 2970 Ma have been identified in the Precambrian rocks of Australia, Canada, China, Finland, India. Namibia and Zambia. The Malanjkhand porphyry copper deposit M.P., India is estimated to contain 789 Mt (870 million st) averaging 0.83% copper (mill headgrade); 0.004% molybdenum; 0.2 g/t (0.006 oz/st) gold; 6 g/t (0.175 oz/st) silver and a cap of 7.5 Mt (8.2 million st) of oxide ore averaging 0.8% copper. The economic potential of the expanded copper mining milling, smelting and refining complex is expected to yield cathode copper 118.6 kt (130,700 st); molybdic oxide 830 t (914 st); gold 1.9 t (61,732 oz); silver 46.6 t (1.5 million oz); sulfuric acid 240 kt (264,500 st), copper from leach dumps 11.5 kt (12,600 st); nickel 24 t (26,400 st); cobalt 84 t (92,600 st); bismuth 16 t (17.6 st); selenium 48 t (53 st), tellurium 4.8 t (5.3 st).

Jan 1, 1995

By G. van Hout, D. Rahal

Caving is a mass mining method that is normally applied to large, low grade orebodies because of its low production cost and high capacity. However, equipment breakdown and poor draw management can cause mining costs to exceed that of all other mining methods. One way to minimize the effect of disruptions in the mining cycle is to use Mixed Integer Linear Programming (MILP) for long-term scheduling. This paper describes a MILP goal program which has the dual objectives of minimizing deviation from the ideal draw profile while achieving a production target. Schedule optimization is performed using a life of mine approach in which all production periods are optimized simultaneously. The underlying assumption being that material mixing in the short-term (between monthly optimization cycles) has a minimal effect on the long-term state of the panel. Schedule optimization is carried out using six general constraint types to model and control production. The constraint types define: deviation from ideal practice, panel state, material flow conservation, production quality, material flow capacity and production control. These constraints define production targets and drive production toward the ideal profile while maintaining correct mining practice. Application of the model using production scheduling data for a De Beers kimberlite mine. It is shown how different production control constraints regulate production from individual drawpoints as well as recovery of the ideal panel profile by implementing an optimised draw schedule.

Jan 1, 2003

Who's Who in Mineral Engineering - The 1979 Directory of the Society of Mining Engineers of AIME

Jan 7, 1979

By C Li, D O’Dea, R Moreno-Atanasio, T Honeyands

The behaviour of iron ore granules in the feeding process of sintering is significantly influenced by the material properties of the granulated mix. Therefore, the measurement of key material properties of the iron ore granulated mix is indispensable prior to the simulation of the sintering process based on the discrete element method (DEM). In this paper, three key property parameters of the iron ore granulated mix, apparent density, elastic modulus and rolling friction coefficient, were measured in laboratory-scale experiments. For different sintering processes, the moisture content of the granulated mix normally varies according to the specific requirements for granule size distribution and operating conditions. Therefore, understanding the effect of moisture content on the property parameters of iron ore granules is very helpful in accurately determining the property parameters for DEM simulation work. In this paper, six groups of iron ore granule samples with six levels of moisture contents were prepared through granulation and the trends in apparent density, elastic modulus and rolling friction coefficient with the increase of moisture content were plotted and analysed based on the measurement results. The results show that as moisture increases from 6.9 per cent to 9.1 per cent, the apparent density decreases from about 3000 to 2800 kg/m3. With moisture increasing within the same range, the elastic modulus first decreases from over 200 MPa to below 100 MPa and then reaches a relative constant value of about 40 MPa at higher moisture contents. Rolling friction coefficients are measured using two methods with both indicating a similar trend, with the rolling friction coefficient first decreasing and then rising as moisture increases from 6.9 per cent to 9.1 per cent. The relationship between µr and µ’r is assumed to be similar to that between static and dynamic friction coefficients.CITATION:Li, C, Moreno-Atanasio, R, O’Dea, D and Honeyands, T, 2017. Variation in property parameters of iron ore granulated mix with moisture content, in Proceedings Iron Ore 2017, pp 79–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By W. M. Jansen

In many mineral processing operations, the reported production figures for an accounting period may not make the best use of available data. While most of the mathematical approaches, such as check-in/check-out, mass balancing, used in effective metallurgical accounting strategies are well understood, the sources and magnitude of measurement errors generally are not. As part of the 'AMIRA P754-Metal Accounting and Reconciliation' project, a study was undertaken at the Northparkes copper/gold concentrator near Parkes, New South Wales to examine the data used in their concentrator metallurgical accounting system. This paper summarises the results of a detailed examination of the mass measurement systems around the concentrator as well as the primary sampling system used for grade estimation. The goal of this work was to develop practical techniques to quantify the error (ie both accuracy and precision) of the measured metal accounting information. With this information, statistical confidence levels for this data can then be calculated. If the errors are small, the effect of error in each piece of measured data can then be propagated to other calculated production figures such as recovery and feed grade using a statistical technique called `the propagation of error'.

Jan 1, 2007

The changes in layout and design over 48 years, from the first crushing and shiploading plant installed at Whyalla in 1915, up to the present plant being built at Koolan Island, Yampi Sound may be summarized as follows.1. Smaller motors and lower power consumption have resulted froma. oil lubrication, where practicable, in place of grease,b. a high pressure "oil-lift" device to reduce starting torque in crushers with white metal bearings, andc. roller bearings in place of white metal.2. Short centre drives with pivot-based motors permit controlled loads on bearings and a reduction in size of crusher houses and motor rooms.3. Dust proofing and pressurising of crusher houses and motor rooms reduces working temperatures and improves cleanliness.4. Variable speed pan feeders give improved plant control, with the use of one man only, and remove the need for large surge bins between crushing stages.5. The use of diesel quarry trucks to dump ore through a "drive over"tip results in faster truck cycles.6. Elevated cylindrical silos with air operated chutes, replace long horizontal storage bins with multiple manually operated side discharge chutes for loading rail cars, and give faster and more accurate truck loading. The silos are charged by belt conveyors with automatic distributors.7. Increased shipping bin capacity (40,000 tons at Whyalla and 6O,OOO tons being built at Koolan Island) caters for the bigger vessels now in use and envisaged for the future. Automatic travelling distributors deliver ore to the bins in layers to ensure, maximum mixing and a more uniform grade for blast furnaces.INTRODUCTIONThe Broken Hill Proprietary Company Ltd has six major crushing plants in Australia at its principal sources of raw material. These are at Iron Knob bench G, Iron Knob scree ore plant, Iron Baron, and Cockatoo Island, all of which are ironstone operations. The other two plants are at Rapid Bay, a limestone quarry, and at Ardrossan, which is the Company's only source of dolomite.

Jan 1, 1963