Search Documents

By John J. McKetta. Jr., Louis B. Lesem, George H. Fancher

The proration of oil produced in the field frequently is based partially or entirely upon the gas-oil ratio of wells. The measurement of the gas-oil ratio is one of the more important field tests in regulatory and pro-ration work, and the test always should be conducted according to standardized methods and procedure. Obviously, the gas-oil ratio and the volume of gas produced by a well depend upon many factors but should be independent of the method of measurement and of the devices used to measure gas and oil. Consequently, the volume of gas accompanying a barrel of oil produced by a well may be measured by any reliable and accurate device or instrument. Frequently either a critical flow prover or an orifice well tester is used for this purpose, and for a particular well the same rate of flow of gas should be obtained regardless of whether a critical flow prover or an orifice well tester is employed in the test. In Texas, when using either instrument, either Capacity Table 1 or 5' is employed in making the necessary computations. If the tables are used, a discrepancy always is found whenever the two instruments are compared by extrapolation to the same conditions of flow. Clearly, Tables 1 and 5 must be at fault in some respects. The orifice well tester and the Bureau of Mines type of critical flow prover are essentially the same instrument; both devices utilize a square-edged orifice 1/8 in. in di-ameter as the primary element, and both freely discharge gas to the atmosphere. Tables for the orifice well tester' have been published in the ranges of 0 to 15 in, of water and 0 to 40 in. of mercury (Hg) differential in pressure. Coefficients for the critical flow prover have been published for differentials in pressure greater than 75 psia. An extrapolation of either differs from the other set of data as much as 18 per cent at some points. No immediately obvious reasons for the discrepancy was found, and data available from the literature were insufficient to effect reconciliation. Consequently, a series of experiments was performed to check the available data and to determine discharge coefficients for the two devices in an overlapping range of differential pressure. The correlating equation used in preparation of tables such as Tables 1 and 5' is the so-called hydraulic equation, Q = C1 vh .....(1) The tables cover orifice sizes from 1/8 through 1 1/4 in. A second set of tables, for use with greater differentials in pressure, apply only to the 3/4, 1, and 1 1/4-in. orifice plates over a pressure range of 0 to 40 in. of Hg. The correlating equation used in preparation of the tables is Q = C2 vH(29.32 + 0.3H)/G . (2) Each of these equations is valid only for the range to which it has been applied, and neither equation is valid for extrapolation. Theoretical equations for flow through an orifice are based upon assumptions of fractionless flow and an emergent jet the size of the orifice. A multiplier, C,, called the discharge coefficient, is inserted into the theoretical expression to compensate for both frictional losses and the contraction of the jet experienced in the plane of the orifice. Buckingham3 shows that C, should vary with the ratio of upstream to downstream pressure for flow of a compressible fluid at any average linear velocity through the orifice less than the velocity of sound. Work published by the National Advisory Committee for Aeronautics4 indicates that the variation continues into the so-called critical flow region until the vena contracta coincides with the plane of the orifice. The NACA work, however, does not indicate a leveling off of the coefficient. The work of the Bureau of Mines5 for the critical flow prover was based on differential pressures greater than 75 psi and indicates that the discharge coefficient, Cd, is constant in this region at a value of about 0.86.

Jan 1, 1958

By John D. Corrick

The environmental and nutritional characteristics necessary for maximum copper extraction from a low-grade ore by Ferrobacillus ferrooxidans have been explored as have many of the limiting parameters. Criteria considered were oxygen consumption, copper extracted, soluble copper concentration, temperature, pH, particle size, nutrients, and other inorganic salt concentrations. A set of environmental and nutritional conditions were developed for E. ferrooxidans Which supported cell reproduction and maximum microbial oxidation of a low-grade copper sulfide ore. Percolator tests conducted under these optimum conditions resulted in an 18 percent increase in the quantity of copper microbially extracted over that extracted under conditions considered to be standard. Manometric tests determined those extremes of environmental conditions and nutritional factors Which were detrimental to the extraction of copper by E. ferrooxidans.

Jan 1, 1965

By J. E. Gebhardt, D. W. Fuerstenau

The use of small quantities of polyacrylic acid (PAA) was found to significantly improve the flotation of fine-sized hematite particles at pH 4.1 and 0.001 M NaCl with sodium dodecykulfonate (SDS). Low polymer dosages before collector addition aid flotation by forming flocs of primary particles, but excess polymer results in low flotation yields due to surface saturation by the hydrophilic polymer. Contact angles, measured on a hematite disk, substantiate the hydrophilic nature of an adsorbed polymer film. Pre-adsorbed PAA reduces the amount of SDS adsorbed on the hematite particles, but the flotation of hematite flocs occurs, even at reduced amounts of adsorbed SDS, and is not depressed until PAA dosages in excess of the saturation value are used. Separation of a hematite-quartz mixture can be achieved by SDS flotation of PAA,-flocculated hematite. Maximum selectivity results with the addition of small quantities of PAA, while excess polymer is detrimental to the recovery of hematite. Consecutive flotation states on a single feed yield a higher grade hematite product at some expense to the overall recovery.

Jan 1, 1987

By H. Tan

The effect of carbonaceous matter on gold extraction was investigated in cyanide systems with pure gold as well as pre-robbing sulfide gold ores. Auger studies demonstrated that the carbonaceous matter preferentially smeared on iron sulfide rather than aluminosilicate surfaces during wet or dry grinding. During mechanically mixed leaching, coating of sulfides and silicates and stripping of carbonaceous matter occurred simultaneously. TEM and XPS studies indicated preferential coating in the form of elemental (graphitic) carbon at the edges and the defect sites of particles. Interestingly, carbonaceous matter extracted from the gold ore was predominantly graphite and not preg-robbing in a solution with a high KCN concentration. However, the carbonaceous coating had a significantly detrimental effect on gold dissolution when gold was pre-ground with the gold ore. Artificial coating on gold surfaces with the natural carbonaceous matter from the ore was also found to substantially retard gold dissolution. With the addition of the natural carbonaceous matter from the gold ore, gold extraction from two non preg-robbing sulfide gold ores was inhibited owing to carbonaceous coating. The presence of carbonaceous matter significantly reduced the current density for gold oxidation and increased the current density for pyrite oxidation. This could explain the fact that carbonaceous coating hindered gold dissolution while enhanced sulfide preg-robbing.

Jan 1, 2005

By G. L. Gates

The Bureau of Mines studied the scales formed in producing wells in the Wilmington field, California. The scales were primarily barium sulfate and resulted from the mixing of injected sea water and formation waters; there was excess sulfate in the injection water and the formation waters contained appreciable barium. After breakthrough, the produced brines were supersaturated with barium sulfate. Laboratory tests indicated that barium sulfate precipitated quickly When the supersaturated brines were agitated with crystals of barium sulfate and fairly rapidly when more sulfate solution was added. Precipitation occurred slowly on standing or under nonturbulent conditions. Both the apparent and equilibrium solubilities of barium sulfate in these brines were determined and compared with equilibrium solubilities in distilled water and sodium chloride solutions.

Jan 1, 1965

By M. S. Frasad

The State of Minnesota is interested in stimulating the development of clay resources and recently supported a two year project to collect data on geological, mineralogical, processing, economic and environmental aspects of such potential developments. This paper presents the .various process options adopted on the bulk samples collected from the Minnesota River Valley area which is a primary deposit and contains a major silica fraction. A standard test flowsheet involving degritting, dispersion, HGMS, and cycloning was developed and for some samples yielded an acceptable filler grade product. Secondary streams containing relatively high grade kaolin but of coarse size were also obtained. Improvement in particle size distribution and in physical properties related to paper product specifications (brightness, viscosity) were obtained by size reduction processes. Market and economic considerations for kaolin consumption in the upper Midwest are analyzed. Current markets for paper grade kaolin in Minnesota were briefly discussed.

Jan 1, 1990

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing cloy reining, crushing, and grinding methods and costs at various operations throughout the United States. These Toners are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production casts. Although the publication of total production cants might not be advisable in sore instances, yet a knowledge of operating costs is essential to the technical discussion end study of the methods employed. The attention of the reader is specifically coiled to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The following report deals specifically with the methods employed by the Clay City Fire Co., Uhrichsville, Tuscarawas County, Ohio.

Jan 1, 1936

By J. P. Hager

The formation of the vapor complex AgFeC14 (g) baa been identified and its thermodynamic properties determined. The vapor pressure of silver chloride can be enhanced by a factor of 15-20 due to the formation of the vapor complex. The vapor pressure of both AgCl (g) and AgFeC14(g) were measured using a double-zone transpiration .technique. Gibbs free energies have been determined for the vapor transport reactions. Laboratory kiln tests were conducted to confirm the enhanced recovery of silver through the formation of the AgFeC14(g) vapor complex and to indicate the opportunities for process development using this new vaporization chemistry.

Jan 1, 1985

By A. W. Khair, L. D. Gehl

"This paper describes the study of bit wear characteristics on three types of rock namely Tennessee sandstone, Berea sandstone and Indiana limestone. High content of quartz with quartz cement in Tennessee sandstone causes removal of material from the bit body and dam2ge to the tip of the bit resulting into excessive weight and height loss as compared to other two types of rock. The drum speed and water spray pressure do not contribute significant effect on bit wear. The polycrystalline compact diamond (PCD) tipped bits are more wear resistant than the ordinary tungsten carbide (WC) tipped bits, but, due to wider body of PCD bits, the wear rate increases particularly at greater depth of cut. INTRODUCTIONThe impact of bit-rock interaction during the cutting process in underground coal mines has always attracted the-interests of mining operators, researchers and the manufacturers. Coal cutting bears directly on airborne coal dust generation which causes ""black lung"" in coal workers. On the other hand, rock cutting generates frictional sparks causing face ignitions. The bit wear not only produces airborne rcspirable coal dust , but also affects the productivity, safety and economy. Hun and Evans (J) concluded that the point attack bits have greater ignition potential than the conventional wedge shaped bits. The results of a study (2) suggested that after 7% of weight loss, the bit should be replaced. In a survey study (3), it was found that the bit consumption of bit had an effect on the productivity and utilization of the continuous miners. The mining industry is yet to receive a solution which could provide them with optimum operating parameters for coal cutting machines in underground C9al mines.The study was, therefore, taken up to determine wear characteristics as influenced by the rock propenies and varying operating parameters. For the purpose of this study, three types of rock, Tennessee sandstone, Berea sandstone and Indiana limestone were used. The machine operating parameters included (i) drum speed, (ii) water spray pressure and (iii) bit type. Besides studying the wear characteristics, the effects of these parameters on the required cutting force, specific energy consumption, acoustic emission generation and bit temperature rise were also studied. Also, the preliminary experiments were performed to compare the bit wear between PCD and WC tipped bits."

Dec 1, 1995

By Nadia C. Miller

In situ metals research to characterize the hydrology of a fractured crystalline rock mass in under-ground mine stopes is discussed. The objective of this study was to find the potential direction, velocity, and concentrations of a lixiviant plume, should leaching solvents (lixiviants) escape from a test stope. The study was conducted by the U.S. Bureau of Mines at the Colorado School of Mines Experimental Mine in Idaho Springs, CO. Since this was a method evaluation site, the lixiviant was simulated using water and acceptable tracers. The site is located in moderately fractured Precambrian migmatite-biotite gneisses of the Idaho Springs Formation. The data required for the characterization were obtained from geologic maps and reports, core logs, and air and water permeability tests. The acquired data were analyzed and applied to a computer model that calculated' the characteristics of a lixiviant plume originating at the stope. A sensitivity analysis showed that dispersivity, ground water velocity, fracture porosity, and fracture spacing had notable effects on the concentration of the plume. Assuming a saturated rock mass, the lixiviant plume would disperse to undetectable levels in a very short time because of a high fracture density at the mine site.

Jan 1, 2010

By R. O. Burt

The original flowsheet of the TANCO mill consisted of a simple two-stage gravity circuit for the recovery of the tantalum concentrates. With decreasing grade and grain size of the tantalum minerals, considerable modifications to the circuit have been required. This paper discusses the various recent improvements carried out 011 all stages of the flowsheet, which have resulted in a 10% increase in recovery. Future improvements, including on stream analysis, and the possibility of tantalum flotation , are also discussed.

Jan 1, 1979

By P .. R. Ammann

A two-stage pyrometallurgical process has been developed for the recovery of copper (and other non-ferrous metals) from copper smelter slags. All types of slags, including highly oxidized, converter-type slags, are cleaned in an electric furnace which employs mechanical mixers to promote magnetite reduction and copper extraction at high rates. In a 10-ton pilot furnace, it has been demonstrated that slags can be cleaned to 0.2-0.3 per cent copper with economically acceptable usage of raw materials and energy; copper is recovered as a high-grade matte. Pilot plant data have been scaled up to a commercial furnace and engineering designs have been made for a furnace to treat 60 tons per hour of slag from a Noranda Reactor and the associated converters. Plans are being formulated for the construction of a prototype slag cleaning furnace.

Jan 1, 1976

By Wen-Ming Chien, Vamsi Krishna Kamisetty, Amrita Mishra, Ivan Gantan, Prathyusha Mekala, Dhanesh Chandra

"The phase equilibrium and characterization studies by using high temperature X-ray diffraction (XRD) and differential scanning calorimetric (DSC) methods have been performed for binary organic thermal energy storage materials. The organic thermal energy storage materials undergo a solid-solid state phase transition before melting which stores large amounts of thermal energy. Two materials [tris(hydroxymethyl)aminomethane(TRIS) and 2-Amino-2-methyl-l, 3- propanediol(AMPL)] were used for this study. Binary samples of AMPL-TRIS were prepared to perform high temperature XRD characterization and DSC studies and the binary AMPL-TRIS phase diagram was developed. The high temperature solid-state phases of AMPL and TRIS were characterized as a disordered BCC structure. It was found there is virtually no solubility of TRIS in AMPL or vice versa below -75 °C. The maximum solubility of TRIS in AMPL is 11% TRIS at 75 °C. The eutectoid transformation was shown at 19%TRIS-81%AMPL composition and at a temperature of 75°C. Lattice expansion calculations on single phase of TRIS and AMPL have been performed.IntroductionThermal energy storage materials can store a large amount of heat due to the presence of thermal transitions from the orientationally ordered to disordered phases occurring before melting. These molecules (such as amine and alcohol derivatives of neopentane) can reorient as a whole about the central carbon atom to form orientationally disordered crystals (ODIC) and their spherical shape makes them reorient relatively easier. Thermal energy storage materials are becoming increasingly important as a renewable energy resource. These molecules undergo large changes in enthalpies at solid-solid transitions. The presence of these compounds with large enthalpy changes are identified as potential thermal energy materials and some of die applications are solar cell systems [1-3]. Binary mixtures have been found as a way to adjust the transition properties in addition to pure compounds [4]. Tris(hydroxyrnethyl)aminomethane (TRIS, C(CH2OH)3NH2) and AMPL, CH3C(CH2OH)2NH2) are two important thermal energy storage materials."

Jan 1, 2012

By P. Saha, D. M. Chakrabarti, J. P. Srivastavam, P. Bhattacharyya, B. R. Sarkhel, Banerjeem B.

The phosphatic soil deposit at the Sukulu hills region of Uganda contains 10-12% P2O5. The ore occurs as a naturally degraded soil deposit containing a very sticky slime composed of earthy lateritic minerals. Desliming of the ore, which is imperative for its further beneficiation, is an extremely difficult hurdle to overcome for its commercial utilisation. Earlier studies on samples of the same ore at the National Metallurgical Laboratory (NML) and abroad established that it was necessary to pass the ore through a series of three stages of desliming, each consisting of a step of vigorous attrition scrubbing followed by hydrocycloning, for effective elimination of the sticky slime. In the present paper an innovative use of the very strong shear-fields created inside a hydrocyclone has been discussed, that could effectively eliminate the stubborn slime from the ore. The standard design of the hydrocyclone was suitably modified to increase the shearing effect on the slurry. It was possible, through the application of this modified hydrocyclone, to not only totally eliminate all the stages of attrition scrubbing, but also to reduce the subsequent stages of hydrocycloning. The modified technique yielded a concentrate of grade comparable to that obtained by employing the earlier more complex flow sheet, with about 25% higher P2O5 recovery.

Jan 1, 2003

By Fujio Ishii

The deoxidation of liquid nickel and nickel binary alloys with silicon has been determined at temperatures between 1500°C and 1650°C using quartz crucibles in order to investigate the deoxidation of nickel based alloys. The equilibrium constant of the deoxidation reaction in liquid nickel and the effects of the different alloying elements such as chromium, molybdenum, tungsten, iron, cobalt and coppcr on the activity coefficient of oxygen in liquid nickel have been established.

Jan 1, 1993

By T. G. Joseph, M. Bolster, M. Curley

"High tirerim loading on haul trucks operating on rough ground frequently manifests as mechanical separations and rim base cracking caused by cyclic fatigue. This paper provides an understanding of the impact of high loads on rim component life and tire footprint, bulge, and deformation behaviour; and develops a maintenance planning tool to predict strain implications of high g loading for a given rim location. Loading tests and analyses were conducted for a tirerim arrangement under increasing load and internal tire pressure. Graphical models were developed, allowing higher g load extrapolation predictions for specific rim components.KEYWORDS g load, Mining, Model, Prediction, Rim, Strain, Tire bulge, Tire footprint, Ultra-class vehicleRÉSUMÉ L’application d’un chargement élevé sur le système pneu/jante de camions de transport rou¬lant sur des terrains accidentés se manifeste fréquemment par des séparations mécaniques et une fissure à la base de la jante engendrée par une fatigue cyclique. Cet article nous permet de mieux comprendre l’incidence de l’application de charges élevées sur la durée de vie des composantes de la jante ainsi que sur l’empreinte, la hernie et le comportement de déformation des pneus. Il développe également un outil de planification de l’entretien visant à prévoir l’incidence des contraintes en cas d’application d’un chargement g élevé sur un endroit donné de la jante. Des essais et des analyses de la charge ont été effectués pour un agencement pneu/jante soumis à une charge et une pression interne du pneu croissantes. Des modèles graphiques ont été développés, ce qui a permis d’établir des prédictions sur la base d’une extrapolation du chargement g plus élevé appliqué à des composantes spécifiques de la jante.MOTS CLÉS charge g, contrainte, empreinte du pneu, exploitation minière, hernie du pneu, jante, modèle, prédiction, véhicule ultralourdINTRODUCTION The purpose of this paper is to report on a proposed and trialed tire performance test based on data obtained from controlled testing that is used to predict the impact of high g loading on hauler rims and tires with greater accuracy. For example, for many years oil sand mining operations have expressed qualitative beliefs that an impact load of the magnitude experienced by a rim and tire arrangement is not detrimental to a rim as a stiff component; however, mining equipment components are subjected to cyclic loading where failure can result from repeated load/unload activity, truncating the peak region of a stress–strain response and resulting in fatigue failure at a stress value that is less than the peak value. The outcome reported by oil sand haul truck maintenance groups indicates they have realized that most high g impacts—such as those experienced by hauler tires and rims operating on poor ground conditions—can result in failure due to cyclic loading, where higher loads require fewer cycles for failure. This high-level loading and the resulting strain transmitted to the rim is evident in the results of the laboratory testing presented in this paper."

Jan 1, 2019

By Gerhard Braüner

The report gives a review of the methods of predicting mine subsidence; these methods are used particularly in European coalfields. The methods are subdivided into two groups, based on mathematical expressions either for the trough profile or for the influence of infinitesimal extraction elements. The fundamental relationships common to all methods described herein are the principles of superposition and of equivalent extraction areas. The involved parameters are derived from field observations. For calculating horizontal displacements, their relation to the slope of the subsidence profile is applied. The time-dependent development of the subsidence process is characterized by the empirical "time factor." Modifications for the case of inclined strata are considered. A brief review of experimental and theoretical model investigations is given.

Jan 1, 1973

By N. W. Bliss

"Bauxite has been the almost universal ore of aluminum for about 100 years, with most of the world's reserves oc¬curring in the developing countries. As a result of fiscal and political activities prompted in part by the energy crisis, the formation of the IBA combined with increasing freight and labour costs, these reserves are no longer as competitive or as secure as they once were. This has given fresh impetus to the development of processes for alumina production that utilize raw material other than bauxite. Canada has no bauxite and it is prudent to look for alter¬native raw materials within our own boundaries suitable for one of these processes.Of the three igneous rocks that have been used as a source of alumina, only anorthosite is considered as a potential source in Canada. The Al content would be extracted by a sinter process, which currently requires a raw material with a. minimum of 28% Al2O2. Thus, about 4 tons of anorthosite and 10 to 12 tons of limestone are needed to produce one ton of alumina. There are two petrologically distinct types of anorthosite, one containing the plagioclase andesine-labradorite and around 26% Al2O3, and the other containing upwards of 30% Al2O3, in by¬townite-anorthite; for our purposes they may be con¬sidered as low- and high-alumina anorthosite respectively. The high-alumina anorthosites are somewhat rare; the low-alumina anorthosites are much more common, partic¬ularly in Eastern Canada. Geologically speaking, there is no shortage of anorthosite in Canada. The reserves are im¬mense, although their low Al2O3 content coupled with con¬siderations of location, access and proximity to limestone could be constraints to their development. Fly ash from coal-fired thermal power stations and nepheline syenite can also be used in a sinter process, but neither is likely to be utilized in Canada in the immediate future.The H+ process utilizes an acid attack to leach Al from a raw material with at least 20% Al2O3. One of the best raw materials is kaolinite-bearing clay; not only is it high in Al, but most of it can be extracted. With the possible exception of the Whitemud clay in Saskatchewan, Canada is apparently deficient in clays with sufficient reserves to support an alumina plant utilizing the H+ process. Low-alumina clays with illite and montmorillonite may also prove to be a suitable raw material if advantageously sited with respect to industrial centers. The average shale con¬tains only 15% Al2O33, much of which may be contained in minerals, such as feldspar, not amenable to acid leaching. If shale is used as a source of alumina, it will be because it contains some other valuable commodity, such as oil or uranium, the extraction of which leaves the spent shale upgraded in extractable Al2O3 and lowers the over-all costs to a point where it is economic, Thus, rejects from coal washing plants are most commonly considered as a source of alumina; they are already mined, are available in large and ever increasing amounts, and may contain significant amounts of combustible material which upgrades the Al2O3, content of the resulting ash. Coal rejects from existing and developing coalfields in Alberta and British Columbia are a possible source of raw material, but present data indicate they may contain insufficient Al2O3."

Jan 1, 1976

By Howard Clarke, Cyril Stanley Smith, Clarence Zener

THE importance of cold-working in the fabrication of metals is in marked contrast with our ignorance as to the nature of the accompanying internal changes. The failure of the usual methods of testing to provide a consistent picture of these internal changes has given the incentive for the present program of investigating the effect of cold-working upon the internal friction of metals measured at small strain amplitudes. It has previously been shown1,2,3, that the internal friction introduced by cold-work is removed by annealing at comparatively low temperatures. In the present paper the following additional factors are investigated: (I) frequency of measurement, (2) amount of cold-work, (3) temperature of measurement. Special care was taken to minimize the internal friction due to causes other than cold-work. The present paper is purely experimental, the authors believing that any conclusions drawn from this work as to the nature of the internal changes accompanying cold-work would be premature." PREPARATIONS OF SPECIMENS In this study of cold-work it was desirable to eliminate as far as possible all other sources of internal friction. One disturbing source is the lack of temperature equilibrium between adjacent crystallites of a vibrating specimen.4 Temperature equilibrium is aided by small grain size and by the use of low-frequency vibrations. Unless unduly long specimens are used, low frequencies can be obtained only in transverse vibrations. But in transverse vibrations a second source of internal frictions is present, that arising from transverse thermal currents.5 The effect of these may be reduced by increasing the transverse dimensions. The grain size and transverse dimensions of the specimens were thus so chosen as to render the vibrations simultaneously nearly isothermal with respect to intercrystalline thermal currents, and nearly adiabatic with respect to transverse thermal currents. The material for this investigation was a 70-30 brass, part of the same lot of material that was used for some earlier studies on the effect of strain on proportional limit.10 It had the following composition: copper, 70.59 per cent; zinc, 29.39; lead, 0.01; iron, 0.01. This material was received from the brass mill in the form of 3/4-in. rod, cold-drawn to final size by a 65 per cent reduction of area from material that had been annealed to give a grain size of 0.060 mm. Rods of appropriate length were annealed for 2 hr. at 400°C. and cooled in air. The annealed rods (grain size, 0.012 mm.) were then stretched in a tensiontesting machine, using special grips10 to ensure axial application of the load. The rate

Jan 1, 1941

By Hsing Kuang Lin

Ferric chloride leaching w.as applied to a complex sulfide ore from Tok, Alaska to dissolve zinc, lead, silver and copper. Gold in the leaching residue, as well as in the ore, is found to be refractory to the conventional cyanidation process. Roasting, pressure oxidation and elemental sulfur removal followed by cyanidation were tested to improve gold dissolution. Also tested were thiourea leaching and high-pressure cyanidation. The readsorption of dissolved gold by carbonaceous matter in the chloride leaching residue was analyzed. Based on the experimental results, factors causing difficulty of gold dissolution from the leaching residue are discussed.

Jan 1, 1989