Search Documents

By W. Choi

The present study revealed that the bioleachability of a chalcopyrite flotation concentrate is influenced by the semiconductor properties of CuFeS2. The overall reaction of biooxidation,

Jan 1, 1991

By Joseph W. Horne

This report presents the results of an investigation by the U. S. Bureau of Mines in cooperation with the State of Colorado, on the yields and properties of oils produced from oil shale, lignite and subbituminous coal using the standard assay method developed by the Bureau for oil-shale testing,. The purpose of this work, which is part of the general study of oil shales being conducted by the Bureau of Mines and cooperating agencies, was to obtain information on the amount and character of the yield of crude oil or tar from different typical oil shales, the yield of light oil or naptha that might be suitable for use in motor fuels, and other products of shale oil. As the west has large resources both of oil shale and low-grade non-coking coals, it is of interest to know the relative yields of tars, light oils, and combustible gases that can be produced from these coals when retorted under conditions similar to those suited for oil-shale retorting. Source of Samples The coal samples were obtained from deposits on or adjacent to the public lands in the States of the Rocky Mountain region. Many of the mines sampled are operating under Government leases or permits. The number of coal samples secured from the various states are: Colorado, 6; Montana, 9; north Dakota, 6; New Mexico. 1; South Dakota, 1; Wyoming, 9. Of these samples, 14 were lignite coal, 16 subbituminous coal, and a bituminous coal. The standard channel method of the Bureau of Mines was used for sampling. Coal samples received at the Boulder Office weighed about twelve pounds each, and duplicate samples were sent to the Pittsburgh Station for proximate and ultimate analyses. The origin of the samples and description of the deposits are given in Table 1.

Jan 1, 1927

By Theodore H. Budd, Douglas J. Heinz

This report concerns the successful construction of Contract No. 287 of the Northeast Side Relief Sewer System for the Metropolitan Sewerage District of the County of Milwaukee. The contract involved the construction of approximately 3316 meters (10,880 feet) of tunnel concrete lined to 1.83 meters (72 inch) internal diameter; 30.48 meters (100 feet) of 1.83 meters (72 inch) reinforced concrete pipe jacked-in-place; a river crossing of approximately 107 meters (350 feet); 197 meters (647 feet) of 1.83 meters (72 inch) reinforced concrete pipe in open-cut; several diversion and flow monitoring structures; and miscellaneous manholes and appurtenances. The contract proposal, which was extremely prescriptive, did allow alternative methods of primary support consisting of precast reinforced concrete segments, steel liner plates, steel ribs with wood lagging, and combinations thereof in designated areas. The specifications required the contractor to designate which support scheme it intended to use. The specifications also required compressed air as a means of ground water control for approximately 2316 meters (7600 feet) of tunnel. The alternative selected in the bid proposal was the support method consisting of steel ribs and wood lagging for 2263 meters (7425 feet) of tunnel and steel liner plates for the remaining section. Shaft supports, by specification, were designed to be steel liner plate with steel ribs varying in size from 4.27 meters to 6.10 meters (14 foot O.D. to 20 foot O.D. ).

Jan 1, 1983

By A. C. Richardson

The mine of the Porter Coal Co. is located at the town of Porter in the northwestern part of Jefferson County, Ala., about 20 miles west of Birmingham. The operations in this mine are confined to the middle and bottom benches of the Mary Lee bed. The coal from the Porter mine is handpicked and washed before being placed on the market. The handpicked lump coal and the washed egg and nut coal are sold chiefly as domestic and steam-raising fuel. The coal finer than 1 inch is washed in 2-compartment jigs and utilized in the manufacture of metallurgical coke. The coal company has found that, when coal ranging in size from 1 to 0 inch is washed in jigs, a considerable amount of high-ash material finer than 3/16 inch remains in the washed coal. This paper gives the results of an investigation which was conducted for the purpose of determining the washing characteristics of the through 3/16-inch raw coal and the extent to which the ash might be reduced by means of coal-washing tables. This investigation has been made in connection with an extensive study of the coal-washing problems now being conducted by the United States Bureau of Mines and the University of Alabama, with the cooperation of the coal-mining companies of the State.

Jan 1, 1933

Geostatistical literature has been dealing with recoverable reserve estimation techniques for the last 30 years. There have been well established support correction techniques (Le. affine correction, indirect log-normal correction, etc.) to deal with volume -variance relationship globally in determining what will be the reserves above a cutoff grade during mining. Kriging has become the accepted technique in the mining industry for ore reserve estimation. Many large companies are using this method for gold and copper deposit modeling. In general, the estimates coming from kriging are smooth. The variances of the block grades estimated by kriging are often lower than the material that will be mined selectively. As a result, kriging tends to under estimate reserves at high cutoff grades and overestimates them in low cutoff grades. It is necessary to perform additional steps after kriging if the goal is to determine recoverable reserves at some cutoff and not the in situ resources. In the mining industry, it is becoming more and more common for the low grade heap leach projects to consider whether the higher grade portion of a deposit may be processed by a mill at higher profits. Similarly, a concentrator -refinery operations are implementing heap leach -SX-EW option for the lower grade portion of their deposit. These options are making it very critical to estimate the low and high end of the grade distributions more accurately. Ore reserve estimation is normally done by using widely spaced exploration data which has very small size support (Le. core samples). Selective mining is carried out on ore control that is based on closely spaced blasthole data normally averaged into larger polygons based on some cutoff grade. Estimated grades from exploration data need to reflect the variability of the grades of the selectively mined units if they are used without further adjustments to predict recoverable reserves.

Jan 1, 1997

By H von Blottnitz, J L. Broadhurst

Eco-efficiency has been proposed by the World Business Council on Sustainable Development as an environmental performance indicator framework that contributes to sustainability by assisting corporate decision makers improve the environmental performance of their operations and processes, while also extracting additional economic value. Given that the recent engagement of the minerals industry with sustainability has highlighted the need for requisite tools and methodologies, it is therefore of interest to assess whether eco-efficiency indicators can drive sustainability performance improvement during process design within the minerals industry. Previous work indicates that the choice of sustainability performance indicators to be used for decision making needs to be governed by the decision context; ie the performance indicators need to be fit-for-purpose. Here, the strengths and weaknesses of eco-efficiency indicators are analysed using case studies. First, a more rigorous definition of eco-efficiency indicators for the minerals industry is proposed based on indicators currently offered in the literature. Two case studies are then selected to reflect typical decision situations encountered within minerals process design. For each case study, eco-efficiency indicators are computed and are compared to more traditional graphical representations of the economic and environmental performance of process design alternatives considered. The sensitivity of these indicators to various process design parameters is also investigated. Results confirm that the meaningful application of eco-efficiency indicators is strongly dependent on the decision context in which the process data is generated. Results also show that eco-efficiency indicators can be related to technical process design parameters to allow for richer communication of performance information for various decision trade-offs; however, in some cases, graphical approaches that provide more insights into the environmental-financial trade-offs should be preferred. The research thus contributes to guiding the selection of the appropriate tools for more environmentally sustainable design of minerals beneficiation processes.

Jan 1, 2009

By S. Shankar

Available literature on the effect of re-entrainment on overall airborne dust concentration in mine airways or the fundamental mechanisms of coal dust re-entrainment in mine atmosphere is scant. Therefore, as part of the Respirable Dust Center's ongoing research, a three part study was envisaged: study of the re-entrainment phenomena of anthracite and bituminous coal dust particles in a wind tunnel under the influence of varying air velocities; study of the same in the Lake Lynn Laboratory Mine of the USBM with both airflow and walking by personnel causing re-entrainment; and mathematical modeling and computer simulation of the re-entrainment phenomenon. In this paper, results from the re-entrainment studies in the wind tunnel and the Lake Lynn Laboratory Mine are presented. Further, the results from the wind tunnel studies are compared with the results from in-mine studies conducted at the Lake Lynn Laboratory Mine of the USBM. Comparing the results from the two studies it was observed that increasing air velocity increased the rate of re-entrainment, but increased time of exposure decreased the airborne dust concentration. Compared to same size particles, a mixture of sizes created more airborne dust concentration when re-entrained. It was also observed that contribution of airborne dust concentration due to airflow was negligible compared to the contribution due to walking.

Jan 1, 1995

By D. E. Redmon

Exploration of hidden mineral deposits becomes increasingly important as known ore reserves are depleted. The primary objective in any exploratory program is to obtain enough reliable information to evaluate accurately the potential of the mineral deposit. Constant improvement in equipment and technique has established drilling as one of the most valuable methods of exploration. This paper presents the results of studies of several drilling methods currently used in the search for uranium deposits in sedimentary formations from surface drill sites. Also presented is a description of drilling with wire-line equipment from an underground location in metamorphic rocks. The studies were conducted in the Colorado Plateau area and in northwestern New Mexico and Wyoming. Statements of a general nature pertain to conditions or situations existent in those areas.

Jan 1, 1960

By N. O. Johnson

This is one of a series of-Information Circulars dealing with mining and milling methods and costs at mines in various districts in the United States. The Hog Mountain gold mining district is of the northern edge of Tallapoosa County, in the east central part of the State of Alabama. The district is equally close to Goodwater and to Alexander City, both stations on the main line of the Central of Georgia Railroad. From Alexander City the mine is reached by 13 miles of graded road, traveling in a northeast direction. In dry seasons the road is good; in wet weather it is bad but passable. Improvements are being made constantly on the road, so that in the near future the gravel road should be good under all weathered conditions.

Jan 1, 1936

By Arshad Ali, Mudassar Khan, Waqas Ahmad, Nisar Muhammad, Muhammad Salman

Talc is an important industrial commodity due to its wide-ranging intrinsic properties; however, the presence of iron oxide hinders its industrial utilization. Herein, we report the purification of Pakistani talc through acid leaching assisted by chlorination techniques. Among various acids (i.e., HF, HCl, H2SO4, HNO3, H3PO4, Aqua Regia, H3BO3, and CH3COOH), HF was the most effectual, removing up to 67% of iron oxide at optimized conditions of temperature, 90–95 °C; time, 120 min; HF concentration of 5%; and at a pH of 1. In the second step, chlorination of the talc sample was performed separately by both wet chlorination and dry chlorination. Wet chlorination was carried out using KMnO4 and HCl in slurry phase which shown about 52% removal of iron oxide, whereas dry chlorination with CaCl2 at high temperature attained about 48% removal of iron oxide from talc sample. Further, the wet chlorination of HF leached samples was also performed under optimized conditions which showed up to 87% iron oxide removal. The original and treated talc samples were characterized by EDX and XRD analysis to monitor the changes in the elemental and mineralogical composition of the talc. It can be concluded that HF leaching followed by wet chlorination is an effective method for the upgradation of low-grade Pakistani talc ores.

Aug 9, 2021

By Owen Matthews

Introduction For the past year and a half, the mill of Cochenour Willans Gold Mines, Limited, McKenzie Island, Ontario has been roasting arsenopyrite-gold concentrates, prior to cyanidation, by means of a roaster employing techniques that are new and novel. The roaster is known as the Dorrco 'fluo-solids reactor', and the technique as 'fluidization'. The reactor has demonstrated its ability to roast a flotation concentrate containing arsenopyrite, pyrite, stibnite, small quantities of other sulphides, and some lime silicates and carbonates, yielding a calcine consisting mainly of porous iron oxide, plus the gold values. This calcine is readily amenable to cyanidation. Bulk shipments of concentrates to a distant custom smelter, as practised prior to this installation, has thus been eliminated, with appreciable savings in smelting charges, freight costs, and interest losses during shipment and smelting. This is the pioneer installation of fluo-solids roasting at a Canadian mill and up to the present performance results have not been published. It is the purpose of this paper to present the information now available for the benefit of other millmen who may be confronted with identical or similar problems to those encountered and solved at Cochenour Willans.

Jan 1, 1949

By G. E. Pearse

Reports, discussions, a written contribution and two written replies are presented from 11 sessions on: Safety and compressed air; Ground movements; Geotechnical; Channel Tunnel (2 sessions); Machines; Case histories; Transport tunnels; Case studies; Site investigation; and Undersea tunnels

Jun 13, 1905

The Federal Coal Mine Health and Safety Act of 1969 requires that each operator of a coal mine shall take accurate samples of the amount of respirable dust in the mine atmosphere to which each miner is exposed, a measure designed to prevent the development of coal workers' pneumoconiosis. This textbook manual is used in the training of personnel to operate respirable dust sampling devices and to conduct sampling programs. It contains the portions of the act applicable to respirable dust standards, the procedures to be followed to insure compliance with Federal regulations, and descriptions of sampling devices.

Jan 1, 1971

By N. Agron-Olshina

The application of the QEM*SEM image acquisition and analysis system to the measurement of the mineral matter in coal and the materials in fly ash is described. A new sample mounting technique was developed using iodinated epoxy to provide a backscattered electron contrast between the coal, the mounting medium and the mineral matter. Several comprehensive and detailed species identification programs for silicate minerals and materials were developed to analyse the 1000 count x-ray spectra used for the measurements. Case studies are presented to demonstrate the capabilities of the new technique to distinguish different coals and fly ashes by their mineral and material composition rather than by conventional chemical analysis. Applications of the new technique are aimed at demonstrating that composition and size distributions obtained from OEM*SEM measurements can be used: 1. to characterize coal with respect to combustion problems in power stations, 2. to characterize coal for fine coal cleaning, 3. to characterize fly ashes in relation to problems such as erosion in combustion systems and the ease of precipitability in dust collection facilities, 4. to refine the classification systems used in marketing coal for pulverized fuel firing and fly ashes as a component of cement and building materials.

Jan 1, 1992

By Renfeng Song, Shaoyan Wang, Zhiqiang Zhang, Ke Guo

Leaching titaniferous magnetite concentrate with alkali solution of high concentration under high temperature and high pressure was utilized to improve the grade of iron in iron concentrate and the grade of TiO2 in titanium tailings. The titaniferous magnetite concentrate in use contained 12.67% TiO2 and 54.01% Fe. The thermodynamics of the possible reactions and the kinetics of leaching process were analyzed. It was found that decomposing FeTiO3 with NaOH aqueous solution could be carried out spontaneously and the reaction rate was mainly controlled by internal diffusion. The effects of water usage, alkali concentration, reaction time, and temperature on the leaching procedure were inspected, and the products were characterized by X-ray diffraction, scanning electron microscope, and energy dispersive spectroscopy, respectively. After NaOH leaching and magnetic separation, the concentrate, with Fe purity of 65.98% and Fe recovery of 82.46%, and the tailings, with TiO2 purity of 32.09% and TiO2 recovery of 80.79%, were obtained, respectively.

Jun 16, 2021

By J. W. Perez

A simple exponential model has been developed (Perez and Aplan. Process Mineralogy, VI, 1986) to describe the fractional yield of a given species out of a locked assemblage: Fractional Yield of Species A = a e X/U where 'X' is particle size and 'a' and 'U' are constants. In the present study, the general validity of this model has been further demonstrated. experimentally, for the liberation of coal and pyrite out of various raw coals and beneficiated fractions using a variety of crushing devices. Using data from the literature, the model is also shown to be applicable to the liberation of sulfide minerals out of ores.

Jan 1, 1987

By Sam S. Taylor

"INTRODUCTION This report deals with a comparatively simple application of some of the engineering principles involved in the evaluation, installation, and operation of air- or gas-injection projects and well-clean-out and repair methods to increase the producing rates of oil wells in partly depleted pools during the war. The methods suggested for developing gas-injection projects take into consideration that in general no new wells will be drilled because of wartime restrictions of equipment and manpower and that only existing wells and second-hand machinery will be used. Because air will be employed as the injection medium in secondary-recovery operations where natural gas is scarce and expensive, the disadvantages and hazards accompanying, its use are discussed. Engineering techniques recognized as best modern practice are discussed in relation to the effect of simple air-injection development of properties on postwar operations and Probable ultimate recovery of oil. The report is an introduction to where, when, why, and how an air-injection project should be installed and operated; it is not intended to be an engineering manual for technical guidance in the selection, development, and operation of simulative methods of oil recovery.The report is intended mainly for these thousands of operators in the Appalachian region owning a few wells prodding small quantities or oil daily. Many such operators are anxious to increase their production rates by simulative means and to rehabilitate their wells so that they will produce more oil to help win the war but, in general, are unfamiliar with secondary-recovery operations and cannot afford to hire technical assistance."

Sep 1, 1944

By Linda C. Carrico

Those who manage the Nation's mineral resources rely upon a variety of organizations both public and private--to give them accurate mineral data, technical guidance, and expert advice. This directory provides a list of such organizations--a list that should prove a useful tool for those seeking mineral-related information and technical assistance. The directory lists Federal and State governmental agencies and national, regional, and State associations with activities in the mineral, metal, and material sectors of the economy. These organizations regulate mining, monitor mineral production, establish and enforce health and safety standards, identify and evaluate mineral resources, conduct scientific research, predict market trends, resolve environmental issues, and promote the interests of the mineral industry, its individual sectors, and its workers--to name a few of their functions. The listings in this directory--arranged by State--should help users who manage mineral resources identify agencies and organizations that can provide mineral-related information or technical assistance.

Jan 1, 1993

By W. G. Miller

An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of this overall study, consolidation tests using slurry consolidometers were carried out for caustic and non-caustic fine tailings. The influence of a change in bitumen extraction process (caustic versus non-caustic) on consolidation properties, namely compressibility and hydraulic conductivity, was determined, as was the effect of adding a coagulant (calcium sulphate [CaSO4]) to caustic fine tailings. For fine tailings originating from two different oil sands ores (Ore A and Ore B), results were presented in terms of variation in average void ratio with time (settlement), void ratio with effective stress (compressibility), hydraulic conductivity with void ratio and coefficient of compressibility and hydraulic conductivity with sodium adsorption ratio. Findings indicated that chemical characteristics of fine tailings (water chemistry, degree of dispersion) do not have a significant impact on their compressibility behaviour and have only a small influence at high void ratio (low effective stress). The biggest advantage of non-caustic fine tailings and treating caustic fine tailings with coagulant is an increased initial settlement rate and slightly increased hydraulic conductivity at higher void ratios. Thereafter, compressibility and hydraulic conductivity is governed by effective stress.

Aug 1, 2010

By W. G. Miller, J. D. Scott, D. C. Sego

An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of this overall study, consolidation tests using slurry consolidometers were carried out for caustic and non-caustic fine tailings. The influence of a change in bitumen extraction process (caustic versus non-caustic) on consolidation properties, namely compressibility and hydraulic conductivity, was determined, as was the effect of adding a coagulant (calcium sulphate [CaSO4]) to caustic fine tailings. For fine tailings originating from two different oil sands ores (Ore A and Ore B), results were presented in terms of variation in average void ratio with time (settlement), void ratio with effective stress (compressibility), hydraulic conductivity with void ratio and coefficient of compressibility and hydraulic conductivity with sodium adsorption ratio. Findings indicated that chemical characteristics of fine tailings (water chemistry, degree of dispersion) do not have a significant impact on their compressibility behaviour and have only a small influence at high void ratio (low effective stress). The biggest advantage of non-caustic fine tailings and treating caustic fine tailings with coagulant is an increased initial settlement rate and slightly increased hydraulic conductivity at higher void ratios. Thereafter, compressibility and hydraulic conductivity is governed by effective stress.

Jan 1, 2010