Search Documents

By R. S. Kinasevich

As part of other work related to the studies of kinetic factors that influence the flotation of specific sulphide minerals, specially designed kinetic flotation experiments at Cominco included work done on -65 + 100 mesh and -100 + 150 mesh, high purity galena. The flotation collector used was sodium isopropyl xanthate containing radioactive sulphur-35. Radiation monitoring of the galena fractions from stage flotation tests indicated that the adsorbed radioactive xanthate was uniformly distributed among the floated fractions and the non-floated, or residual portion of the galena. This anomalous behaviour could not be correlated to changes in Seebeck coefficients, to lattice distortions, or to the nature of the mineral surface as revealed by infrared spectroscopy and by microscopic measurements.

Jan 1, 1970

By L. F. Rooney

In June 1964 the Indiana Geological Survey discovered gypsum beds more than 10 ft thick in rocks of Devonian age in La Porte County, Ind. Although the extension of the Michigan Basin evaporites into northern Indiana has been recognized for some time, the gypsum beds have been regarded as either too thin or too deep for exploitation. Current Survey research, however, indicates that exploration by industry might find commercial deposits of gypsum less than 50 miles from Chicago. In four cores taken by the Survey within 1 sq mile in La Porte County, the maximum thickness of inter-bedded gypsum and anhydrite is 35.8 ft. Both gypsum and anhydrite beds contain irregular masses of limestone and dolomite that average a few inches in cross section and total about 20% of the rock by weight. The maximum thickness of gypsum in one minable unit verified by core is 12.5 ft, and its purity is 81.3%. Chloride content of the gypsum beds is less than 0.005%. Depth to the gypsum in La Porte County is 330 to 500 ft, about the same depth as the gypsum being mined in Martin County, Ind. In June 1964 the Indiana Geological Survey discovered gypsum deposits of probable commercial thickness near La Porte, Ind. (Fig. 1). This article presents preliminary data on the distribution, thickness, depth and chemical composition of the gypsum, the possible causes of gypsification, and economic considerations of immediate interest to industry. Because of the preliminary nature of the work, only a few geologic relationships concerning the genesis of the deposits will be mentioned. DEFINITIONS The following terms used throughout this article have been restricted to the following definitions: evaporites: anyydrite (CaSO4) or gypsum (CaSO4 . 2H2O). minable evaporites: any evaporite unit which may contain more than 80% evaporites, which is more than 10 ft thick, and which in places may be completely gypsified. PREVIOUS WORK The presence of gypsum and anhydrite in the Devonian rocks of northern Indiana has been recognized for at least 70 years1-4 and can be inferred from a number of reports on the geology of Michigan. For example, in a cross section from southwestern to central Michigan, Ells5 indicated the presence of

Jan 1, 1965

By R. Mensah-Biney

The aqueous biphase separation process (ABS) has been used to separate ultrafine industrial minerals. The partition behavior of TiO2, Al2O3, Fe2O3 and kaolin was not pH dependent. The partition behavior of SiO2 was, however, pH dependent. The partition coefficient of kaolin in PEG 3400/ Na2CO3 biphase system was = 150 and that of the silica in the same system was = 0.02, resulting in a separation factor of = 8500 between kaolin and silica. The aqueous biphase separation system was used to separate free silica from kaolin in a raw clay sample from Mexico. The partition behavior of mica, feldspar and clay from North Carolina was also evaluated.

Jan 1, 1999

By R. A. Cortese

The U.S. Bureau of Mines has developed a flame-radiation-powered trigger device to explosively activate suppression barriers to quench gas and coal dust explosions. The major component of the device is a silicon solar panel, which converts radiation from the developing explosion into electrical energy to initiate an electric detonator, which releases an extinguishing agent into the advancing flame front. Solar panels that are rated to produce 20 W of electrical power when exposed to the sunlight are producing about 200 W when exposed to a full-scale dust explosion. The solar panel is electrically isolated from the detonator by a pressure-sensitive switch until the arrival of the precursor pressure pulse, which always precedes a deflagration. This combination of pressure arming and flame-powered photogenerator prevents false barrier activation and requires no external power supply.

Jan 1, 2010

By Stephen L. Bolivar, Susan H. Balog, Thomas A. Weaver

A data-classification scheme was developed to detect potential uranium mineralization in the Montrose l º x 2º quadrangle, Colorado. The methodology developed is a rapid and efficient method of resource evaluation on a reconnaissance scale. The necessary techniques were developed and refined to digitize, integrate, and register various large geological, geochemical, and geophysical data sets for the Montrose quadrangle, Colorado, using a grid resolution of 1 km. All data sets for the Montrose quadrangle were registered to the Universal Trans- verse Mercator projection. The data sets include hydrogeochemical and stream sediment analyses for 23 elements, uranium-to-thorium ratios, airborne geo- physical survey data, the locations of 90 uranium occurrences, and a geologic map (scale 1:250 000). Geochemical samples were collected from 3965 locations in the 19 200 km2 quadrangle; aerial data were collected on flight lines flown with 3-5 km spacings. These data sets were smoothed by universal kriging and interpolated to a 179 x 119 rectangular grid (each grid block is 1 km2). A mylar transparency of the geologic map was prepared and digitized. All possible combinations of three, for all data sets, were examined for general geologic correlations by utilizing a color microfilm output. Subsets of data were further examined for selected test areas. A classification scheme for uranium mineralization, based on selected test areas in the Cochetopa uranium district, is presented. Areas favorable for uranium mineralization, based on this scheme, were identified and are discussed.

Jan 1, 1982

By S. Itoh, T. Nagasaka, J. Ono

With respect to the recycling of used lead-batteries, a pure lead is required to prepare a lead-calcium alloy electrode for a new maintenance-free battery. The pure lead can be obtained by means of electrolytic and/or pyrometallurgical refining. In the lead electrorefming, antimony is concentrated in anode slime. From the viewpoint of the recycling and recovery of metal values from used lead-batteries, especially from anode slime, oxidation experiments were conducted for pure liquid antimony in the temperature range between 973 and 1373 K to elucidate the oxidation kinetics and mechanism. Furthermore, since lead anode slime generally consists of antimony, lead and bismuth, experiments have been also carried out using antimony-lead-bismuth alloy. The equation relating to the mass transfer characteristics in the gas phase was then applied to analyze the oxidation kinetics. As a result, it was found that the anode slime treatment, that is, an oxidation of antimony concentrated in anode slime followed by vaporization as antimony oxide Sb406, should be operated with higher oxygen partial pressure and sufficient amount of gas flow rate at lower temperature around 1073 K. The feasibility of the oxidation treatment for anode slime has been also discussed.

Jan 1, 2004

By Richard E. Beane

For several decades, the minerals industry has used leaching techniques to extract metals from rocks whose grade was too low to be treated profitably using conventional metallurgical techniques, and, as of 1972, about 15% of domestic copper production was derived using leaching methods (Beall 1). Increasing interest is currently being directed toward solution mining, particularly with respect to copper, for basically two reasons. In the first place, geological exploration has outlined several copper deposits of large tonnage and 1m', grade which are buried at sufficient depth to preclude open-pit mining which would make such mineral deposits ore deposits. Nevertheless, these occurrences provide significant potential if they could be treated by chemical leaching in situ. Secondly, the porphyry deposits of the western united States, which provide by far the largest percentage of domestic copper, do not terminate geometrically with sharp borders. These large disseminated bodies commonly decrease in grade laterally away from volumes of rock containing ore grade metallization, and the distinction between ore and waste is strictly economic. In order to extract ore grade material from the ground, a significant amount of rock containing sub-ore-grade copper must also be removed which, when placed on dumps, is amenable to solution mining. These two considerations clearly indicate the reasons for the growing interest in solution , leaching techniques--namely the ability to exploit deeply buried low grade deposits and the expansion of reserves in deposits currently under production.

Jan 1, 1977

By Otto Robert Stein

Erodibility of reclaimed surface mine soils is a subject in need of quantification. Effects of soil erosion from reclaimed areas may damage surrounding areas and the quality of water in nearby streams and lakes. It may also reduce the potential productivity of the reclaimed site. A study was conducted to determine erodibilities of different reclamation treatments and a nearby unmined soil at three Indiana strip mine sites. A rainfall simulator was used to artifically erode plots con¬structed within seven treatment categories and the unmined soil. Soil erodibility was assessed in terms of the Universal Soil Loss Equation (USLE) K factor. Values for K calculated from field data were compared to values predicted from independently measured soil properties. Differences in soil erodibility between treatments were site specific. Unmined soil had the highest calculated erodibility at one site but at two other sites soils having reclaimed A horizons were highest. Shaley overburden treatments had the lowest calculated erodi¬bility. Predicted soil erodibility was usually lower than that calcu¬lated from field data. Site specific slope gradient factors (S) were developed for reclaimed A horizon treabnents. This was done because the USLE S factor overestimated the measured soil loss at steeper slopes.

Jan 1, 1983

By G. L. Gates

Five possible sources of water for waterflooding of petroleum reservoirs in the arid San Joaquin Valley of California were considered. Three of them (water produced with petroleum, water from a shallow saline aquifer, and waste irrigation water) were analyzed chemically; laboratory information for one (sea water) had been developed during a previous study. A series of laboratory tests made on the fifth source (fresh water) determined the solubility of calcium sulfate dihydrate in water. Laboratory analyses included the following: Chemical analyses of water produced with petroleum and waste irrigation water; solubility of calcium sulfate dihydrate in water and brines; the effect of excess sulfate on the solubility of calcium sulfate in brines; the presence of sulfate-reducing bacteria; and the permeability of cores from a petroleum reservoir to air, to water from other petroleum reservoirs, and to waste irrigation water. The results showed that most of the waters and mixtures of waters are compatible with petroleum reservoir waters and are generally suitable for injection. The calcium content of some of the formation waters is quite high, and care must be taken to prevent precipitation of calcium sulfate dihydrate. The permeability of the few cores tested was about the same to water and brines as to air, indicating that formation damage due to clay swelling will not be serious. The waters most likely to be available for injection are water produced with petroleum, water from shallow saline aquifers, and waste irrigation water.

Jan 1, 1970

By John T. Popp, Jodi A. Rulli, Anthony T. Iannacchione

Anomalous geological features in the coal and surrounding strata of a mine in northern West Virginia have fractured and deformed an inherently weak roof rock prior to mining. Horizontal stresses, as much as six times greater than overburden related horizontal stresses, have induced cutter roof failure. This failure was distinguishable from rock deformation associated with geological anomalies because it was induced by mining. The characterization of these features has allowed for the prediction of zones of unstable roof rock and the determination of failure trends on gateroad stability. Geological anomalies included clastic dikes and a narrow zone of sandstone roof. Clastic dikes, representing intrusions of shale and claystone, were invariably accompanied by local roof rock instability, and often formed the boundaries of roof falls. Shale was the dominant roof lithology except where a small sandstone occurred in the northwest portion of the longwall mining area. The sandstone occurs in two phases: a sandstone-filled channel, 5-m- thick and 60-m-wide, which eroded and replaced the shale roof and the upper part of the coalbed; and a sheet sandstone unit which was crossbedded to interbedded with the underlying shale. Horizontal stresses are naturally relieved through the initiation of cutter roof failure. This failure may extend from a few meters to several tens of meters horizontally, and from a few centimeters to several meters vertically. Orientations of entries and crosscuts has a greater influence on the direction and total length of cutter roof failure at the rib-roof intersection than does the principal directions of the in situ horizontal stresses. Seventy-four percent of the cutter roof failures occurred along the rib-roof intersection. Orientations of cutter roof failure away from the rib- roof intersection were clustered in the north-south direction and may have been influenced by the horizontal stress field.

Jan 1, 1984

By Frederick K. Allgaier

This is the first in a series of progress reports on the longwall subsidence research program at the Bureau of Mines Denver Research Center. As part of this program, the Bureau and the Utah Power and Light Co. are cooperating on a study conducted at the Deer Creek Mine, which is directed toward developing the capability to estimate the surface subsidence resulting from longwall mining in a geologic, topographic, and mining environment common to coalfields in the Western United States. A monitoring network has been established at the Deer Creek Mine to measure subsidence over four adjacent longwall panels. To date, two panels have been mined. Subsidence began as the first panel was mined and continued for 1 year following completion of the panel, during which time the adjacent panel was mined" A maximum of 2.7 feet of subsidence occurred over the two longwall panels mined at a depth of 1,500 feet. Because of the length of time that subsidence continued after mining, the final subsidence profiles and angle of draw have not yet been determined.

Jan 1, 1982

By H. M. Thorne

Oil shale, a potential source of products presently obtained from petroleum, is found in many countries. The most extensive known deposits from the standpoint of potential shale oil in place are those in Brazil and the United States of America. Mining methods used for oil shale range from open-pit operations for shallow deposits to room-and-pillar and longwall techniques for deposits with thick overburdens. Oil shales from different sources vary greatly in the amounts and types of organic and inorganic constituents. By retorting, the organic material is converted to oil, gas, and coke. The largest percentages of oil are obtained from materials having the highest hydrogen content. Over 2,000 retorting systems have been patented, but only a few have been used industrially, and no single process seems best for all types of shales or economic conditions. Shale oils have different characteristics, depending on the source rock and method of retorting. They contain large quantities of olefinic hydrocarbons and more oxygen, nitrogen, and sulfur derivatives of hydrocarbons than most petroleums. Consequently, petroleum refining methods usually must be modified for shale oil. This is particularly true in catalytic processing. Hydrogenation, even under mild conditions, improves shale-oil refinability. Several byproducts may be obtained from both the retorting and refining steps,

Jan 1, 1964

By W. J. Pennstrom, J. R. Arnold

Gold Fields installed what was the mining industry's first commercial gold electrowinning/replate circuit at Ortiz in 1981. Its highly successful operation since that time provided the design basis for a similar circuit at Mesquite, which was started in early 1986. These circuits produce plated gold foil suitable for direct shipment to a refinery or melting directly into bars. Detailed descriptions of the electro- winning and replate circuits are given and advantages and disadvantages are discussed.

Jan 1, 1988

Jan 1, 1990

By Nicholas J. Grant

It is the purpose of this paper to examine a number of the recent developments in powder metallurgy, being most concerned with those which are yet to prove themselves rather than those which have achieved commercial maturity. Such developments include the production of very much coarser and very much finer powders, down to the near-micron size range. Also considered are activated sintering, direct powder rolling and extrusion (both hot and cold), brazing and welding, hydrides of reactive metals, oxide dispersion strengthened alloys and theoretical evaluations. Introduction T HERE surely can't be very much argument with the fact that powder metallurgy has made large advances on many fronts during the past ten or more years (1). These advances have taken place in raw materials, in processing, in product development and in a better understanding of many of the phenomena which occur in the various steps involved in powder metallurgy. It should be clear, in view of such growth, that it will not be possible to highlight all of the new developments in the present paper. Many of these developments,

Jan 1, 1965

By W. W. Adams, V. E. Wrenn

"Production of explosives in the United States during the calendar year 1935 decreased 2 percent from 1934, according to reports covering all companies engaged in the manufacture of explosives during those years.Reports from manufacturers showed a total production of 308,381,250 pounds of explosives; this quantity included 39,170,016 pounds of permissible explosives 5/ 200,323,559 pounds of high explosives other than permissibles, and 68,887,675 pounds of black blasting powder of which 34,222,625 pounds were granular powder and 34,665,050 pounds pellet powder.Coal mines consumed 89 percent of the total production of blasting powder, 99 percent of the total output of permissible explosives, and 11 percent of the output of other high explosives.The metal mines of the United States used 28 percent of all high explosives other than permissloles, less than 1 percent of all permissibles, and 1 percent of all black powder produced.Quarries and nonmetallic-mineral mines consumed 17 percent of the high explosives other than pormissibles, less than 1 percent of the permissible., and 3 percent of the blasting powder.Construction work required the largest quantity, 40 percent of all high explosives manufactured during the year. Less than 1 percent of the permissibles and 6 percent of the black powder produced during 1935 was used in construction work."

Nov 1, 1936

Robert C. Horton was sworn in as the new Director of the Bureau of Mines on October 13 in Washington. Horton, 54, was director of the Geology Division of the Bendix Field Engineering Corporation's operations in Grand Junction, Colorado, before being nominated by - it Reagan for this position. A geological engineer, he has been associated with the mining industry in the West for over 35 years. Legislation to expand the Defense Production Act for 1 year until September 30, 1982, was signed by the President on September 30. The Administration had requested, steel a 5-year extension, but the Congress chose to spend another year considering proposed revisions. The Act, among other things, authorizes the allocation of strategic materials for defense purposes and allows incentives including floor prices and Government financing to encourage domestic mineral projects.

Jan 1, 1981

By Jari Aromaa, Olof Forsen

"Oxygen evolution by decomposition of water is the main anodic· reaction in sulphuric acid solution. Traditional anode materials have been relatively low-cost lead alloys, though the active lead dioxide layer has a high oxygen evolution overpotential. This causes a significant increase of cell voltage. To lower total energy use in metal production, electrocatalytical properties or corrosion resistance to decrease replacement costs must be improved. Addition of an catalyzing ion will decrease oxygen evolution potential. The effective area of an anode increases by calcium additions and by producing anodes with fine microstructure. Remelting and rapid quenching is possibly a method that is economically feasible and technically simple enough to be adopted.IntroductionPermanent anodes are widely used in several electrochemical processes and cathodic protection applications. The permanent or ""inert"" anodes can be either massive or coated anodes. The massive anodes are metals, like lead alloys, or non-metals, like magnetite, graphite or ferrite. The coated anodes are made of a valve metal base (titanium, niobium or tantalum) coated with an electrochemically active coating. The purpose of anodes is to supply current to the electrochemical cell. A vast number of materials and their combinations are electrical conductors and may hence be used as anode materials. However, good anode materials must survive in aggressive environments and also be able to pass high current densities. These opposite requirements restrict the amount of possible materials. Generally, an useful anode material must meet three requirements, electrical conductivity, electro catalysis and stability. Good electrical conductivity is essential for energy efficiency. Good electrocatalytical properties are essential to improve product yield. Long term stability is also an important property, because electrode wear and corrosion may cause product contamination, increasing energy consumption and material and labor costs due to need of periodical maintenance. Electrical conductivity and electrocatalytical properties are more widely studied subjects than long term stability of anodes, and a good amount of information about these two subjects can be found in the open literature. Wear and corrosion mechanisms of the anodes vary depending on the operational conditions, i.e. concentration of different species, temperature and operating current density."

Jan 1, 1997

By R. V. Lundquist

Aeration in water slurries and controlled drying of manganous hydroxide produced from dithionate leaching of Artillery Peak manganese ores from Arizona were investigated by the Bureau of Mines at its Electrometallurgical Experiment Station, Boulder City, Nev., to determine whether a simple process could be developed for converting this product into a battery-grade manganese dioxide. The properties of manganese dioxide prepared by the thermal decomposition of manganous nitrate were investigated also. Manganese dioxide suitable for use in batteries was not obtained from the dithionate leach product, but some of the factors controlling its oxidation were isolated. Aging of manganous hydroxide was of major importance in retarding its oxidation by aeration. Sodium hydroxide and sodium silicate promoted oxidation by drying. Optimum quantities were about 0.85 mol of sodium hydroxide and 0.2 mol of sodium silicate per mol of manganese, and drying temperatures of 200° C. produced yields of manganese dioxide up to 90 percent of the manganese present. Higher temperatures and concentrations of reagents carried oxidation of manganese beyond its tetravalent state.

Jan 1, 1957

By Deno M. Pappas

This report presents results of a U.S. Bureau of Mines study of longwall gob material. The objective of this work was to determine material stiffness properties of the gob for use in numerical models of rock mass response to longwall mining, Photographs of actual mine gob were digitized to obtain approximate particle size gradations of gob material. The gradation curve was shifted down to a laboratory scale, and 20 uniaxial compression tests were conducted. Varying the maximum particle size was not found to affect the stress-strain behavior, but changing the gradation appeared to influence the stress-strain behavior. The stress-strain relationship of the simulated gob material was nonlinear, the stress-secant-modulus relationship was approximately linear, and the stress-tangent-modulus relationship was approximately a second-order polynomial function. Equations were generated from these curves, providing numerical modelers with a means to estimate gob moduli based on the stress level. In addition, the experimental data were statistically evaluated using multiple regression analyses, producing a series of equations to predict the secant and tangent moduli from the given stress level, bulking factor, rock strength, and thickness-to-width shape ratio of the particles.

Jan 1, 2010