Search Documents

By Shuji Owada, Mayumi Ito, Idemitsu Kosan Co. Ltd., Takehiko Nishimu, Sadayuki Shinozaki, Takashi Ando, Tomoe Ota

"fElectrical disintegration (ED) by high voltage electrical pulse is a relatively new technique which was demonstrated by Tomsk and Mekhanobr in the 1960’s and has been investigated in detail by Andres in the 1990’s. In the ED, the electrodes should contact to the targeted material and the energy of high voltage pulse is charged directly to the material. It has been reported that the ED is quite efficient to improve liberation of composite materials, because electrical current passes often through the conductive part and/or along the phase boundaries. Theoretically, the energy required in the ED should be lower than in the other mechanical breakage methods, because breakage occurs basically by tensile strength in the ED while in the other mechanical methods it does mainly by compressive strength which is generally ten times or higher than tensile strength.Coal, involving many kinds of mineral matters, is considered to be one of the targets for the ED to apply to. In Japan, national “Hyper-Coal Project” is now running, in which ultra-clean coal (less than 200ppm of ash, 0.5ppm of Na and K, and 2ppm of Ca) is planned to produce by combining advanced coal preparation and liquefaction technologies for the purpose of direct injection of coal combustion gas to turbine. The ED is one of the major techniques to be developed in this project, since mineral matters must be liberated before introducing to the following advanced separation processes. Liberation is important also for the utilization of middling coals generated from usual coal preparation plants. The application of the ED to the middling coals is considered effective for upgrading these coals with higher liberation degree and less energy input."

Jan 1, 2003

By M. Okido, H. Yamamoto, T. Sakamoto, R. Ichino, K. Kuroda

"Hydrogen absorption alloy films have been produced by molten salt electrolysis. Lanthanum-Nickel alloy film can be formed on a nickel substrate in KCl-NaCl-LaCb molten salts by electrolysis diffusion process. LaNi5 alloy was formed by mutual diffusion between La ·and Ni after La deposition on Ni substrate. Though several kinds of La-Ni compound existed in deposits, the alloy compounds on Ni substrate changed by electrolysis condition. According to the open-circuit potential measurement in molten salts after La electrodeposition, the formed compounds had a relation to the potential. In the case of the substrate electroplated a cobalt thin film on nickel, LaNi4_5Co0.5 was formed by the electrolysis in the molten salts with lanthanum ions. This ternary alloy film showed better hydrogen absorption behavior in cyclic charge/discharge test in alkaline solution.IntroductionHydrogen storage alloys have attracted attention as the active materials for batteries with the charge/discharge property at ambient temperature. The alloy of nickel and misch metal, mainly consisting of La and Ce, has been commercially 'used as a metal hydride with rechargeable property. In recent years, researches have been developed many kind of new alloys with better hydrogen absorption properties. The hydrogen absorbing alloy ingots are commonly produced by melting method of both metals in furnace, otherwise, prepared by mechanical grinding and metallurgical sintering technique with metal powders. The film is also made by vapor-phase techniques such as sputtering method, ion plating method, etc. ·We have proposed a new method to produce hydrogen absorbing alloy films by molten salts electrolysis technique [1-3]. The hydrogen absorbing film, LaNi5, Mg2Ni and CaNi5, were obtained in this process through controlling the electrolytic condition. The active metals, La, Mg and Ca, are electrodeposited on Ni substrate, diffuse into the substrate and form various kinds of intermetallic compounds. This technique provides a direct process using metal chlorides as resources to produce functional films without using active metals such as La, Ca and Mg."

Jan 1, 2000

By K. Ananthpadmanabhan

Hydrolyzable surfactants such as fatty acids and amines undergo, in addition to micellisation and precipitation, various associative interactions in aqueous solutions to form ion molecular complexes such as acid-soap, dimers etc. depending upon the solution conditions such as pH. The interaction of these collector species with the mineral surface and with other dissolved species in solution will play a significant role in determining the interfacial processes such as adsorption and flotation. Marked differences in the hydrophobicity imparted to the mineral surface depending upon the solution conditions such as Ph can be attributed to possible differences in surface activities of the above complexes. This aspect of solution chemistry of flotation systems is discussed here for two widely used collectors namely, oleic acid and dodecylamine. Equilibrium species distribution diagrams based on the available literature .data and on estimates of energy of interactions between molecules, have been obtained for oleic acid and dodecylamine solutions.

Jan 1, 1978

By G. H. Martindill

Complex chemical and physical changes occurring during carbonization result in a heterogeneous system composed of gaseous, liquid, and solid phases, whose relative proportions and chemical compositions change constantly as temperature increases. Studies in which the participating variables are isolated and controlled should be useful in formulating the mechanism of coal carbonization. The most characteristic property of a coking coal is its ability to form a plastic mass at a certain stage of the carbonization process. During this period it is believed that fluidity of the coal influences the properties of the resultant coke. This report gives results of an investigation by the Federal Bureau of Mines of the influence of the maximum fluidity attained by the charge on the physical quality of the coke or char produced. As a first approach to the problem, researchers investigated high-melting-point pitches, which are relatively simple carbonaceous materials. The plastic properties of these pitches, prepared specially for this work, varied greatly; their fluidities, as measured by the Gieseler plastometer, covered most of the fluidity range characteristic of coking coals. Blending these pitches with increasing pro-portions of fine coke progressively reduced their fluidities. Coal-pitch and coal-coke blends also were treated; their fluidities were varied by changing their blending ratios. The various blends were carbonized in a small-scale carbonizer and the resistance of the carbonized residue (char) to abrasion was determined in a small-scale tumbler test, using the Roga drum.

Jan 1, 1960

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisingerm

"As deposits of high-grade base metal sulphides become depleted, attention must be focused on the treatment of complex sulphides, which contain significant fractions of precious metals such as gold and silver. Acid pressure oxidation is a promising process for these materials and the recovery of silver and gold will improve the economy of the process. Gold can be recovered from the oxidised residues, however, silver is incorporated into the jarosite specie and the cyanidation of the resulting residue yields very low recovery.Pressure oxidation of various complex sulphides was carried out at 110-150°C in sulphate media with additions of potassium iodide under conditions similar to industrial autoclaving. The resulting residues were subjected to cyanidation. High recovery of silver, up to 98%, was achieved because its incorporation into lead-hydronium jarosite during the pressure oxidation was minimised, while its deportment into the cyanide-soluble silver iodide was favoured. Silver recovery decreased slightly at high temperatures (140° and 150°C) because of the enhanced stability and kinetics of lead-hydronium jarosite, but this could be overcome by increasing acidity and iodide concentration of the autoclave slurry."

Jan 1, 2003

By M. J. Howes

The high degree of mechanisation, which is mainly diesel-powered, has a significant effect on heat loads; heat output from this source often exceeds the heat flow from the surrounding rock. The extensive use of diesel-powered equipment also influences ventilation rates and minimum values are necessary to ensure that emissions of diesel exhaust are adequately diluted. Many Australian mines are in subtropical or tropical areas with high ambient wet- and dry-bulb temperatures on surface. This, coupled with the large amount of heat from mechanisation, usually means that refrigeration is required at much shallower depths. A secondary problem is associated with the definition of acceptable thermal environment conditions, which are sometimes based on the assumption of no air movement. This gives rise to very stringent thermal environment acceptance criteria, which, in some areas, would prohibit work on surface, let alone underground

Jun 12, 1905

By Serdar Aktaş, Burcu Nilgün Çetiner

According to critical statistical studies, antimony is one of the rarest elements in the world, and global resources could be exhausted by 2050. In light of these observations, its extraction will be costly due to poor-quality ore, deep mining, remote locations, and high energy consumption. In the present study, an alkaline leaching process was carried out on stibnite concentrate to evaluate the effect of reaction parameters on the percentage of antimony extraction. The leaching efficiencies of different sulfur and hydroxide sources were studied and compared to one another to create a better understanding of the reaction process. Kinetic models were investigated to identify the reaction pathway and calculate the activation energy. The activation energy of the stibnite dissolution was assessed as 19.13 kJ/mol using a two-dimensional diffusion-reaction model. The value of activation energy indicates the quantity of energy necessary for a reaction to proceed. As expected, potassium hydroxide leaching was significantly more successful than was sodium hydroxide; however, in terms of economics, the use of sodium hydroxide was found to be more cost-efficient. Interestingly, this finding indicated that caustic leaching is still the most effective method for stibnite extraction.

Jul 23, 2020

By S. L. McGill

The U.S. Bureau of Mines has determined the microwave heating rates for a suite of minerals and reagent-grade compounds. Maximum temperature achieved for the samples and the time required to reach temperature are reported. Heating rates of powdered samples are presented as a function of incident powers up to 3,000 W at 2,450 MHz. Descriptions of the microwave cavities, test cells, and a thermocouple assembly used to measure temperature in the microwave field are given. Many minerals of value heated in the microwave field, whereas host rock or gangue materials did not. In general, heating rates increased as incident power was increased. Exceptions to this were some very good (CuO, Fe304, and PbS) and very poor (CaC03 and SiO2) microwave-absorbing materials that showed negligible changes with increased power. Applications demonstrating the use of microwave energy in mineral processing that are described herewith include oxidation-reduction reactions, mineral liberation, and mercury retorting-vaporization. Microwave data on mineral heating rates will provide insight to possible chemical and mineral processing applications as well as assist in predictions of processing parameters.

Jan 1, 2010

By J. F. Barkley

At the request of several Federal agencies, tests were conducted on a relatively recent type of anthracite -burning equipment named the Anthratube. This device, rated at 130,000 B.t .u. per hour, was designed to burn Pea-size anthracite automatically for steam or hot-water house heating and for domes-tic hot -water supply. ACKNOWLEDGMENTS The helpful cooperation of the Anthracite Institute and the manufacturers of the equipment, Axeman-Anderson Co., Williamsport, Pa., is gratefully acknowledged.

Jan 1, 1953

By van der Walt TJ, van Deventer JSJ, Reuter MA

Owing to their complexity, many metallurgical processes are difficult to model fundamentally, and as a result more attention has been focused on the use of artificial intelligence techniques to simulate these processes. In this paper recent advances in the use of neural nets to model processes not amenable to conventional methods are discussed. These include the application of a new modelling methodology based on the use of neural nets for the dynamic simulation of metallurgical processes, the use of conventional techniques in conjunction with neural nets to simulate gravity separation circuits, as well as the detection of gross errors in variable measurements by means of a neural net representation of the relation between measurement and constraint residuals.

Jan 1, 1993

By R. H. Hiltz

Three titanium alloys, known to provide a mechanically unstable p structure after quenching, were selected as material for a study of the Origin and nature of stress-induced transformation. Data from hardness and tensile tests were used to study the initiation of marten site and the effect of the transfornation and transformation products on the mechanical properties of B titanium, particularly the stress-strain relationships. With the exception that the materials investigated showed a natural aging reaction in the P condition, their behavior is analogous to that of' stress-transforming stainless steels. The transformation starts after initial yielding and is essentially complete just prior to .maximum loading. Once initiated, the martensite itself is capable of propagating the transformation. The deforn-ing materials show low strength, high ductility, and a high strain-hardening exponent. In metallic systems which undergo a diffusionless transformation on cooling, it is possible to produce a similar transformatiorl by plastic deformation under special conditions. Dewez' in delineating Ms temperatures for the titanium-rich end of most titanium binary systems:, established the point of intersection of Ms with room temperature for those particular alloys. Alloy compositions which would quench to mechanically unstable p were established from these data. The first investigation into the possibility of stress-induced transformation occurring in titanium met with little success. It was concluded that such a transformation in titanium was possible only under very special conditions. Continued effort in this direction, however, showed certain Ti-Mo binaries to be highly susceptible to this phenomenon. This fact was utilized by Liu to study the habit planes of martensite and by Machlin and wenig5 to study the effects of stress and plastic deformation on the P to a prime transformation in titanium alloys. The first investigation of the mechanical properties of these alloys was conducted by Holden and his coworkers at Battelle Memorial Institute.' The potentiality of the alloys i3s sheet-forming material was recognized, and the data reappeared in a survey of this type of titanium material.? The initial optimism was tempered by the difficulties in obtaining homogeneous 2i-Mo alloys in commercial-size ingots. The increasing need for good sheet-forming material kept investigation in this direction active, resulting in the development of a commercial alloy of this type.' This study was undertaken to obtain a clearer picture of the mechanism of stress-induced transformation in titanium. MATERIALS AND TEST PROCEDURE Three alloys were selected for this investigation: one a Ti-Mo alloy; another a Ti-Cr-Mo alloy, known to deform martensitically; and the third, a Ti-V alloy with an Ms below room temperature and an Md above room temperature, but known to contain w phase in the quenched condition. The compositions of these alloys are given in Table I. These alloys were cast as 5-lb experimental ingots, employing skull melting. The ingots were hot-forged into 1-in.-round bars. Two 72-in.-thick slices were cut from each bar for hardness testing; the remainder was cut into 0.252-in. tensile blanks. The tensile blanks and one hardness disc from each bar were heated in salt to a temperature 100°F above the 0 transus, held 2/2 hr, and brine quenched. X-ray analysis showed the pieces to be 100 pct 8.* *Omega cannot be distinguished from p by the technique employed. Tensile blanks were machined to size after this treatment. TO prevent transformation due to machining stresses, the shoulders and gage length were ground. True stress-true strain curves were

Jan 1, 1960

By A Weeks, W J. Shaw, A Kuk

Grade control is a process that requires the interaction between many components of the mining operation and successful grade control is only realised through good data, robust systems, and a well-trained, motivated and disciplined workforce.The Mt Magnet Gold Project Pty Ltd (MMGP), a wholly owned subsidiary of Ramelius Resources Limited, started mining at Mt Magnet in February 2012 with high expectations for success. Positive cash flow would fund an aggressive exploration and mine development program in the area to increase mine life. Disappointment followed when after start-up the operation had issues achieving budget grade and realising the predicted grade of the mined ore. In January 2013, things started to improve. During the next six months, gold production steadily increased with successive months achieving record production. What had changed?Improvements started following the realisation that controlling grade was not the sole responsibility of the mining geologist and that everyone on-site has a role to play. This paper examines the factors that delivered success for MMGP.CITATION:Weeks, A, Shaw, W J and Kuk, A, 2014. Who is responsible for grade? – an evaluation of the value chain at Mt Magnet Gold Project, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 477–482 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Zhigeng Xu

Pressure leach of a Yunnan marmatite concentrates with adding coal as the elemental sulfur disperser was investigated. The experimental results show that the coal with carbon content higher than 70% is incapable of dispersing elemental sulfur from minerals and cannot improve the leaching of zinc. The coal with low carbon content (lignite coal) can act as excellent sulfur-disperser in the pressure leaching at 423K. The mechanism of lignite coal as sulfur disperser was further discussed by ultraviolet, infra-red spectrum and mass spectrum.

Jan 1, 2008

By Pengfu Tan

A thermodynamic model and computer program, CuModel, has been developed to model the distribution behaviors of Cu, Fe, S, O, Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag, copper loss in the slag, and heat balance in copper smelting process, matte converting process and copper con-tinuous smelting process. It can be predicted for any set of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxy-gen-enriched air. This model accounts for physical entrainment between matte and slag phases. It can be used in Isasmelt process, copper flash smelting process, Mitsubishi process, P-S con-verting process and Noranda process. The predictions by the present computer model are com-pared with the known commercial data from Guixi Smelter in China, PASAR Corporation in Philippines, Horne Smelter in Canada, MIM Limited in Australia and Naoshima Smelter in Ja-pan. The agreements between the computer predictions and the commercial data are excellent. In this paper, the applications of CuModel in the copper metallurgical industries have been pre-sented. CuModel has been used by Daye Smelter and Guixi Smelter in China, and by PASAR in Philippines as well.

Jan 1, 2004

By D. K. Sengupta

Increased recycling of waste paper has been emphasized in recent years in both the USA and Canada for environmental and economic reasons. Removal of ink particles from the waste paper pulp is therefore necessary. One of the most promising methods for ink removal is froth flotation. Our study investigated the feasibility of a simplified flotation scheme which showed that about 90-92% ink removal can be achieved while 95-97% ink removal is achievable if a hydrophobic polymer is used ahead of flotation. The clean paper pulp recovery was over 90%. The effects of pulping pH, flotation pH, and concentrations of flotation and polymeric reagents are discussed in the paper.

Jan 1, 1993

By Jack G. Croeni

A study was made by the Bureau of Mines to determine the influence of high energy-rate deformation on the structures and properties of low-carbon steel, stainless steel, titanium, titanium-6 percent aluminum-4 percent vanadium, beryllium, molybdenum, and tungsten. The purpose of this study was to determine relative formability, the effect of energy and temperature on metalworking parameters and resulting structures, and the properties of materials formed by this technique. Forming techniques were limited to upset forging and direct extrusion on pneumatic-mechanical forming machines. Results show that considerable grain refinement can be achieved by careful control of deformation and forming temperature by high energy-rate techniques. Significant improvements in strength were observed as a result of this refined structure. Approximate deformation resistance as a function of temperature was determined for a variety of materials.

Jan 1, 1966

By R. Y. K. Yang, O. Olajide, E. H. Cho

"This study focuses on partial leaching of coal pyrite with sodium sulfite in order to increase its degree of liberation from the coal matrix, which might help to increase the removal of coal pyrite, together with trace elements of arsenic (As), selenium (Se) and mercury (Hg) by froth flotation. The U.S. Bureau of Mines’ two-stage reverse flotation process was applied to further reject coal pyrite in the second stage, where pyrite was floated while coal was depressed. The results show that the leached coal flotation with sodium sulfite produced lower pyritic sulfur content in the clean coal by approximately 25% compared to the flotation of unleached coal. The synergism mechanism between the leaching and the two-stage flotation is delineated. The rejection of trace elements (As, Hg and Se) after the two-stage flotation process with unleached coal followed approximately that of pyritic sulfur (64.6%). However, after the two-stage flotation with leached coal, the rejection of Se was as high as that of pyritic sulfur (77.9%), while the rejections of As and Hg were 20% lower than that of pyritic sulfur, or followed approximately the same rejections obtained through the two-stage flotation with unleached coal.IntroductionSO2 is a reducing reagent, but when it is combined with oxygen in an acidic solution, it will become a strong oxidizing reagent for leaching coal pyrite. Sundaram et al. (2001) found that the reagent could leach coal pyrite to produce ferric iron, which, in turn, catalyzed the oxidation of SO2. Similarly, Cho et al. (2009) found that the reagent could leach pyrite as well as mercury from coal. In the present study, coal was preconditioned by partially leaching coal pyrite in water-coal slurry with sodium sulfite at 48° C. The partial leaching of coal pyrite may enhance its degree of liberation from the coal matrix and give a chance to be rejected more effectively during the flotation.The two-stage U.S. Bureau of Mines’ reverse flotation process (Miller, 1975) was used in this study. The first stage is conventional flotation, in which coal is floated while material with higher ash and pyrite content remains in the cell. Kerosene is used as a promoter to float the coal and MIBC (methyl isobutyl carbinol) is used as a frother. In the second stage, the floated coal from the first stage is depressed using a starch-based reagent, while coal pyrite is floated using potassium amyl xanthate. In this second stage, the liberation of coal pyrite from the coal matrix seems to be an important factor for successful rejection of coal pyrite."

Jan 1, 2015

By P. H. Floyd

This report presents the results of laboratory beneficiation tests on a sample of scheelite ore and a sample of low-grade scheelite flotation concentrate from the Sangdong mine, Korea. Sangdong was the foremost producer of tungsten concentrates on two occasions - during part of World War II and in 1953. It was also a significant producer of bismuth concentrates. Resources are very extensive and could support a 5,000-ton annual output of tungsten concentrates for many years. Located in the eastern part of South Korea near the 37° latitude, Sangdong has been a vital source of dollar income for the Republic of Korea in recent years. Its shutdown in March 1954 came about as a result of the great decline of tungsten prices and the fact that a sales contract with the United States Government had been terminated, In addition to establishing new markets, the problem of reopening Sangdong will be related to cost reductions and improving mill recoveries. Large quantities of offgrade scheelite concentrates were produced in the past and shipped to the United States for further beneficiation. Other low-grade concentrates and middlings have been stockpiled or discarded at the mine plant.

Jan 1, 1954

By Johanna Alegría-Ortega

Cr/CrN bilayer coating was deposited on AISI 440C by Cathodic Arc. The composition and structure of the Cr/CrN coating were investigated by scanning Electron Microscope, X-Ray Diffraction and X-ray Photoelectron Spectroscopy. The results show that crystal structure obtained was CrN phase with preferred [220] orientation. The hardness and adhesion of coating also were studied. The evaluation of erosion-corrosion (EC) on 440C bare and coated with Cr/CrN was performed by carrying out wear tests using a slurry jet with impingement angle 90° at 4 and 8 m/s. Corrosion, erosion and synergism wear rate were evaluated following the procedure described in ASTM G-119-09. This study presents that the synergism wear rate exceeds 40% of the total mass loss for coating and 60% of mass loss for the 440C, being the most aggressive wear component. The increase in impact velocity generated a rise in mass loss for both 440C bare and coated. The Cr/CrN coating offers better corrosion and erosion–corrosion resistance under all the tested conditions.

Aug 8, 2018

Jan 1, 1998