Search Documents

This report is a compilation of all information obtained in accordance with the requirements of contracts S0122076 and H0232056. A series of eight coal mines were visited to determine their communications usage and requirements. Presently available equipment was surveyed and evaluated to determine its applicability to the needs of the mines. The equipment studied includes that made by the following companies: Anaconda Telecommunications Division Andrew Antenna Bendix Communications Division Collins Radio Group of Rockwell International Executone Communication and Sound Systems Gai-tronics Mine Safety Appliances Company Motorola Communications and Electronics, Inc National Mine Service Company Plessey Communications Systems Corp Pye Electronics Limited Reach Electronics Set Com Corporation Sonex Incorporated

Jan 1, 1974

By P. G. Shewmon, J. Y. Choi

The surface-diffusion coefficient for , has been measured on (111) and (100) surfaces of copper from 1000" to 620°C. D,(Ge) on the (111) is two to three times that on the (100) as was found earlier for copper and gold on copper. D, (Ge) on both (111) and (100) is about thirty times that found for gold or copper tracers on the same surfaces, while in the temperature range where both D,(Ge) and Ds(Au) have been measured the activation energy for germanium is the same as that for gold. The apparent activation energy for Ds(Ge) is not a constant, but decreases with temperature. In a recent paper we reported on the application of a new tracer technique to the determination of the surface-diffusion coefficient (D,) for gold and copper on (111) and (100) surfaces of copper.' In this paper, we shall give the results obtained when the same technique was used to measure Ds for germanium on the (111) and (100) surfaces of copper. In addition to providing data on D., for an additional element on copper, the longer half-life of germanium (275 days) meant that Ds could be measured down to a much lower temperature and thus over a much wider temperature range (1000" to 620°C) than was used in our gold-tracer work (1060" to 780°C) or copper mass-transport studies (1060" to 800). The apparent activation energy for D, (Ge) is essentially the same as that found for gold or copper in the same temperature range, though the values of D, (Ge) are thirty times greater than those found for gold or copper tracers. The most interesting new result found is that the apparent activation energy for Ds(Ge), and thus Do, definitely increases with temperature. Such a trend was much more apparent in Gjostein's mass-transport work on copper than in our own, though in an earlier paper we mentioned the difficulty of fitting all of our points with one straight line:= No real explanation of this is given though experiments done on grain boundary groove growth at various ambient pressures demonstrate unequivocally that vapor transport plays no part in the increase in activation energy with temperature.

Jan 1, 1964

By Davis M. Lapham

Ore bodies at Cornwall, Pennsylvania, have been mined since 1742 principally for iron from magnetite, but also for copper (in chalcopyrite), silver (in chalcopyrite), gold (in chalcopyrite), cobalt (in pyrite), sulfur, and crushed limestone aggregate. Metallization occurs as a limestone replacement above the essentially conformable, south dipping portion of a discordant saucershaped diabase sheet. Pre-Triassic and Triassic faulting have emplaced host Cambrian limestone and two Ordovician(?) hornfels units, now for the most part resting above diabase. Thermal metamorphism of carbonate-bearing country rocks largely to calc-silicates, is ubiquitous. Metasomatism, particularly of potassium, is unique to ore zones. Associated magnetite- actinolite mineralization replaces, in a preferential sequence, all earlier metamorphic and metasomatic minerals and rarely diabase chilled margin. Mineralogical (diopside, actinolite, mica, sulfides, oxides) and chemical (Fe, Cu, S, Co) zoning of the eastern ore body is focused down dip, near its western edge, along a major vertical fault through diabase. This zoning is spatially related to magnetite veins in diabase, to an ore body within diabase, and to a shear zone that probably extends through the sheet.

Jan 1, 1968

By L. R. Plitt

A new simple correlation has been developed to evaluate the performance of classifiers. The new correlation has been tested on existing data from 150 different hydro-cyclone classification tests. It is shown that this model provides a meaningful improved method of mathematically describing the classification process.

Jan 1, 1971

By Sasa Djokic

In developed countries, the difference between demanded and produced quantities of non-ferrous and rare metals are compensated by secondary raw materials recycling and reprocessing of by-products from both ferrous and non-ferrous extractive metallurgy. Utilization of non-ferrous and rare metals from the metallic secondary raw materials is very significant, both for recovery of the metal value and contribution to the environment protection. Similar to all non-developed countries, the extractive metallurgy in Serbia was based on available natural resources and not so strict environment protection regulations, which was either insufficient or completely absent. Today, Serbia is at the beginning of development of efficient and economical technical and technological solutions in order to ?ecologize? technogenic systems by waste materials, secondary raw materials and degraded soils regeneration (by recycling and revitalization). Several metallurgical technogenic systems in Serbia, together with secondary raw materials classification according to their potentiality for metal extraction by using the existing technologies and expected economical and ecological effects of recycling, are discussed in this paper.

Jan 1, 2005

By David M. Spatz

Ore deposit models are defined largely by physical geologic features that relate conveniently to remote sensing. New Landsat, SPOT, RADARSAT and other multispectral and hyperspectral sensors with improved spatial resolution are currently in development. Near-infrared and thermal airborne hyperspectral scanners hold outstanding promise for both mineral exploration and feasibility stage mapping at potential new mining projects. These scanners are capable of identifying silicification, differentiating silicate alteration types, and mapping compositional variations within igneous and metamorphic complexes. Research in 'mineral and rock spectrometry is helping to advance applications of remote sensing. Hyperspectral scanners are capable of differentiating compositional variations within individual mineral species. Innovative data processing techniques continue to enhance computer software applications and facilitate imagery analysis by the geologist. Today, . remote sensing imagery is commonly integrated with multiple data sets in GIS format to form the core data base for regional exploration programs.

Jan 1, 1995

By J Ferreira

To speed up multivariate geostatistical simulation it is common to transform the set of attributes into spatially uncorrelated factors that can be simulated independently. One decorrelation method is the method of minimum/maximum autocorrelation factors (MAF), where a two structure linear model of coregionalisation is assumed. The transformation decorrelates the theoretical model exactly, but the actual data are only approximately decorrelated. The MAF transformation can therefore be seen as a special case of a non-orthogonal approximate diagonaliser of a set of symmetric matrices. A more general approach for approximate joint diagonalisation (AJD) has been developed in the context of blind source separation. For these AJD algorithms no assumptions are made beyond symmetry of the individual matrices and so they can be applied to a family of experimental semivariogram matrices. In their application there are no restrictions on the number of structures in the linear model of coregionalisation (LMC) thus removing one of the conditions placed on the subsequent modelling of the spatial structure of the factors. In this paper the general background for the U-WEDGE AJD method is presented. It is shown that the U-WEDGE method achieves better spatial decorrelation than the MAF method. The factors derived from U-WEDGE are simulated using conditional turning bands simulation and then backtransformed to attribute space.

Sep 26, 2011

By H. R. Green

The design of slurry launders has usually been based on strictly empirical concepts. An examination of the most common procedures reveals that they do not account for many of the variables that are recognized as Significant for slurry transport. These may include flow rate, volume concentration of solids, solids specific gravity, solids size distribution particle shape, launder geometry, and roughness of the wetted surface. It was decided to develop a design procedure, which would accomplish two things: First: Take into consideration most of the known significant variables and systematize the procedure to assure consistent results. Second: Provide a rational basis for examining and utilizing operating data to refine and improve the system. To accomplish this, it was necessary to develop a basic design concept. This concept has been developed through a complex development history, and yet still appears workable and technically sound. That concept may be outlined as follows: First: The solids transport velocity is the fundamental basis for slurry launder design. Second: The stream configuration, hence the launder size, is integrated with the solids transport velocity so that the actual stream velocity exceeds the solids transport velocity. Third: The launder slope is that which will achieve the required actual stream velocity. It was originally planned to utilize a series of charts and nomographs for the design procedure. A nomograph, based on data given in Taggart's Handbook of Mineral Dressing (1), was developed to determine the solids transport velocity. The velocity thus determined was used with Manning charts to determine the launder slope .and configuration as though the fluid were water. It was planned to utilize a "slope adjustment factor" to increase the slope to compensate for the apparent viscosity of the slurry. All attempts to develop a suitable correction factor failed. This failure was principally due to the complex relationship of viscosity to the required slope. It was then decided to revise the entire approach. Specifically, the present procedure is based on the Darcy-Weisbach flow equation, which is rationally preferable to the Manning equation. The Camp (2) equation is used for the solids transport velocity. The necessity of reference to the Moody curves for the Darcy friction factor is avoided by using the Colebrook and White (3) equation. The resulting mathematics require iterative solutions for several of the unknowns.

Jan 1, 1978

By Dennis A. Hansen

The solubility of anhydrous aluminum chloride in solutions of titanium tetrachloride and vanadium tetrachloride was determined as part of a re-search project-by the Bureau of Mines to make a homogeneous alloy sponge of titanium, vanadium, and aluminum. Solubility curves were established using an autoclave at 75°, 100°, 125°, and 150° C. The solubility of AJC13 in TiC14 is 0.2 wt pct at 75° C; it increases to 18.3 wt pct at 150° C. The data concur with data from earlier researchers of this bi-nary system for 75° to 125° C. For the VC14-AlC13 binary system the solubility of AlC13 is 0.1 wt pct at 75° C, increasing to 1.6 wt pct at 150° C. For the TiC14-AlClrVC14 ternary system the solubility of AlC13 decreases from the values found with a pure TiC14-AlC13 system to the lower values found with a pure VC14-AlC13 system at the respective temperatures.

Jan 1, 1986

By Robert B. Hoekzema

The Bureau of Mines and U.S. Geological Survey completed a 4-yr (1979-82) mineral appraisal of the Chugach National Forest (CNF), AK. This report summarizes the Bureau's placer gold studies in the CNF. Placer mining from the mid-1890's through 1982 produced an estimated 133,800 oz of gold, of which two-thirds was produced prior to 1920. As much as 6,800 oz of placer gold was produced from 1979 to 1982. Most production came from Crow, Canyon, and Resurrection Creeks. Five types of placer gold deposits were identified in the CNF: (1) alluvial placers, (2) bench placers, (3) eluvial placers, (4) glacial placers, and (5) marine placers. Placer sampling indicated a potential for gold production from alluvial and bench placers associated with historically mined drainages such as Crow, Canyon, Resurrection, Sixmile, and Mills Creeks and from unmined drainages including the Avery, Kings, Snow, Copper, and Tasnuna Rivers and several smaller streams throughout the CNF. Results of fineness tests indicated that gold from the CNF ranges from 455 to over 950 fine. Subsequent investigations in drainages with anomalous placer sample values also identified previously unknown lode mineralization.

Jan 1, 1986

By S. Middlemiss

The Indentation Fracture technique is being developed as a tool for use in comminution and mineral liberation analysis. Fracture toughness measurements for a number of mineralogical materials were made and comparisons were drawn between these and properties measured with the Ultrafast Load Cell drop weight apparatus. The technique has also been used as a probe to quantify differences in fracture properties at different areas in the microstructure of a material. In both a Utah limestone and a South African quartzite, material near a grain boundary fractures very differently to that in the bulk. Ongoing work is ultimately aimed at producing a comprehensive fracture model for a multi-mineral system based on its micro-fracture characteristics.

Jan 1, 1994

By S. Tuylu, D. Adiguzel, A. Bascetin, O. Ozdemir, U. Cinar

"In recent years, use of mineral processing tailings as a paste backfill has been significantly increased due to the environmental problems occurred during the disposal of the tailings in mine area. The paste material used to fill the stopes excavated is generally consisted of tailings (solid ratio: 70–85%) and cement (3-7%w/w). Meanwhile, the strength of the paste material is completely related to ratios of these materials. Cemented Paste Backfill (CPB) system is used as support depending on the roof pressure and also as an underground disposal method. Therefore, temporary strength value of the paste material gains a great importance. For example, the paste backfill material must compensate the minimum 4 MPa strength value in order to procure the permanent fortification, and the mixture cost must be minimal as well. For this reason, in this study, the Pb-Zn tailings were used to prepare for the paste backfill material using cement in order to perform the uniaxial compressive strength (UCS) tests. Additionally, a statistical experimental design and linear programming techniques was used to find the optimum mixture in terms of strength and cost. The pulp solid ratios (PSR) of the tailings and cement (by the solid) were varied as 75-85% and 3-8%, respectively. The results of this study; the optimum mixture is ~79.5%PSR and 6.8% cement ratio (by the solid) for 4 MPa UCS (28 day) and 16-17 cm slump value determined by this method with statistically reviewed experimental data. INTRODUCTION Fine-grained tailing waste materials resulting from mining activities are an important environmental problem. In terms of environmental protection, the use of tailings with paste backfill is a very attractive approach and a desirable solution to tailings management. Paste backfill, which is used to fill underground openings, is made by primarly mine tailings mixed with hydraulic binders and water. Its main benefits are not only disposal of mine tailings in underground, but also providing a certain strength to ensure a safe working environment. Therefore, it is necessary to use hydraulic binders due to durability of the system (Benzaazoua et al., 2004). Paste backfill, formed from the mix of dewatered plant tailings (75-85 wt. % solids), water and binder (3-8 wt. %) (Brackebusch, 1994; Landriault et al., 2005).Water is used to determine the chemical reactions between tailing and binder materials for strength as well as increasing pumpability. Portland cement and ash can be used as binder materials (Douglas and Malhotra, 1987). The factors which affect strength and stability of paste backfill separate into two groups called interior and exterior factors. Interior and exterior factors determine the strength, stability and deformation features of backfill in short and long terms and also affect the transportation of backfill to underground (Benzaazoua et al., 2004; Erçikdi et al., 2006; Yilmaz et al., 2010; Nasir and Fall, 2010). Material properties of tailings as well as site operations to fill the underground openings are the most important steps for the design purposes. Grain size distribution, chemical, and physical properties of tailings, and mechanical properties of paste fill material are used to understand the suitability of tailings as paste fill material (Ozturk et al., 2014). In addition, Fig. 1. is also proposed to apply a typical design for the operational stages of paste fill applications on the site."

Jan 1, 2016

By Richard F. Link

A statistical technique, useful to analyze assay and other data characterized by location in three dimensions, is described in this Bureau of Mines report. If present, trends in the data are defined for the purposes of improving ore estimation, predicting ore beyond existing workings, and aiding geological interpretation. The technique is to fit linear and quadratic polynomial equations to the data through the statistical method of regression analysis. The fitted linear equations have the geometric form of hyperplanes; the fitted quadratic equations have the geometric form of ellipsoids or elliptic hyperboloids of one or two sheets. To visualize these three-dimensional forms, contour maps of a series of plane sections through the fitted surfaces are plotted. Both the fitting of the polynomial equations and the plotting of the con-tour maps are done by electronic computer to facilitate calculations and to obtain accurate results. Computer programs are described in appendixes. Methods employed are illustrated by an example analysis) based on data from a part of the Fresnillo mine) Zacatecas, Mexico.

Jan 1, 1966

By Robert C. Johnson

Single crystal whiskers of ZrO2 and TiO2 were grown by solution and crystallization of these oxides in molten baths. Mixtures of Na2B407 and LiC1 were the most suitable growth media for zirconia. Sodium borate alone and Na2CO3 plus SiO2 were best suited for titania. The solubilities of zirconia and titania in molten sodium borate were determined, Whether zirconia whiskers were dendritic or nondendritic depended on the temperature used. The best single crystal whiskers were grown below 1,100° C. Titania whiskers always grew as single crystals. The tensile strengths of zirconia and titania whiskers were about 15,000 psi and 50,000 psi, respectively. Modulus of rupture was about 49,000 psi for zirconia whiskers and 75,000 psi for titania whiskers. Chemical analyses showed the zirconia and titania whiskers to be pure. The zirconia and titania whiskers were shown by X-ray analysis to be, respectively, baddeleyite and rutile.

Jan 1, 1965

By G M. Mudd

The growing popularity of platinum and platinum group metals (or PGMs, including palladium, rhodium and others) for a wide range of applications leads to some interesting issues for mining and sustainability. The uses for PGMs includes catalytic converters for air pollution control in vehicles, growing jewellery use, catalysts for various purposes (especially petroleum and chemicals processing), hydrogen fuel cells and many others. Given the growing importance of most of these PGM uses in more sustainable technologies or in making industrial processes more efficient, it is critical to understand the complex sustainability issues which surround platinum and PGMs. At present, South Africa is the dominant PGMs producer and holds about 88 per cent of estimated global resources, with important but relatively minor production and resources in Zimbabwe, Russia, Canada and the United States. Given the concentrated location of PGM resources, what are the likely trends in PGM mining with respect to environmental sustainability? That is, what are the costs in terms of energy, pollution, greenhouse gas emissions, water, land use impacts, social impacts, economic aspects associated with this globally important industry? This paper compiles and analyses a range of data on platinum-PGM mining, focusing primarily on South Africa. It synthesises a unique combination of data which relates typical production aspects such as ore grade and scale with sustainability aspects such as greenhouse, energy and water costs. The findings are critical in understanding the debate about the increasing environmental and social costs of some materials and technologies which are considered crucial for sustainable industries based on PGMs. Overall, the paper represents a valuable insight into the platinum-PGM sector, providing a range of useful data for understanding the environmental sustainability of this particular group of precious metals.

Jan 1, 2009

By Ian Wark

IN an earlier paper1 measurements of contact angles due to the effect of xanthates on mineral surfaces were reported. The solutions in which these measurements were made differed widely from those of modern flotation circuits. It is intended, however, by introducing, one at a time, the other principal reagents of flotation, to approach gradually the solu-tion composition of flotation liquors. The work now described is an attempt to determine the effect of one of the most important of these reagents-namely, sodium cyanide-on the establishment of air-mineral contact. The work has been carried out for the following companies: Broken Hill South, North Broken Hill, Zinc Corporation, Electro-lytic Zinc of Australasia, Mount Lyell Mining and Railway, and Burma Corporation. Since the effect of cyanide is inseparably connected with the alkalinity, the results cited below deal with the mutual effects of alkalis and cyanide. Alkalis alone exert a significant effect on the air-mineral contact but comparatively large amounts are required. Since the addition of a small amount of cyanide greatly decreases the degree of alkalinity necessary for the suppression of contact at surfaces of any of the minerals experimented with (except galena) and since alkalis are rarely used alone in practice, little attention has been paid to cyanide-free solutions. It was shown in the previous paper that, excluding the dixanthogen effect, whenever contact was practicable at all in an ethyl xanthate solution the angle of contact was 60°. There is, therefore, less necessity to measure equilibrium contact angles; in fact, the experiments herein described have generally been conducted with a view to determining whether contact is possible and not to measuring the actual value of the contact angle. The separations which have generally to be effected in dealing with complex sulfide ores are: (1) galena from sphalerite, pyrite, etc.; (2) sphalerite from pyrite and/or gangue minerals; (3) copper minerals from pyrite and gangue minerals; (4) pyrite from gangue minerals; (5) chal-

Jan 1, 1933

By D. R. Tesarik

To ensure the stability ofa tailings pond embankment, the height of the phreatic surface must be kept at or below a safe level. In this investigation, the Bureau of Mines analyzed various horizontal drain designs for tailings embankments to determine their effects on location of the phreatic surface. This report describes the investigation, and it includes 21 dimensionless graphs that can be used to estimate the drain spacing and length dimensions necessary to ensure the stability of embankments of various configurations. Analyses were based on the use of two computer codes, a three-dimensional finite-element code and a two-dimensional finite-difference code. The computer-generated results were compared with results obtained from a laboratory embankment model, other laboratory test results, and piezomet-ric data from two actual tailings embankments. Nearly the same phreatic surface locations were predicted using either of the computer codes. For one of the actual embankments studied, the predicted phreatic surface location was slightly higher than the measured location; for the other, the predicted location closely followed the actual surface trend. Phreatic surfaces of the laboratory model were slightly higher than the code-gener-ated locations, and the differences grew larger as drain length increased or drain spacing decreased.

Jan 1, 1984

By S. M. Hay

The zinc content of blast furnace and basic oxygen furnace dusts is low compared with electric arc furnace dusts and it is generally not economical to treat the dusts to recover zinc. However, they have a high iron content and removal of the zinc would allow recovery of the iron values. A literature review and thermodynamic analysis was undertaken and, as a result, several smelting options were identified. This paper describes experiments undertaken to develop understanding of metallurgical aspects of these processes which are not amenable to theoretical analysis. Dusts from an Australian steelworks were characterised in order to determine their mineralogical make-up and the form of the iron. The processing aspects investigated in the laboratory were slag-metal equilibrium and solid-state pre-reduction using reducing gases of compositions expected from bath-smelting processes. Particular attention. was paid to the deportment of zinc, sodium, potassium, phosphorous and sulfur between the phases formed during smelting and pre-reduction. The smelting results indicate that less than 10% of the zinc, sulphur, sodium and potassium report to the metal. About 99% of the zinc and potassium and about 80% of the sodium could be volatilised from the dusts by reducing them at 1,000°C with mixtures of CO, CO2, H2 and H2O even when metallic iron was not formed. The experiments indicate that smelting of blast furnace and basic oxygen furnace dusts should produce hot-metal of a composition which can be blended into the main stream of hot-metal in the steelworks.

Jan 1, 1994

By R. Farrar

Protective canopies for conventional electric face equipment, including shuttle cars, operating in low coal (less than 48 inches) were designed, fabricated, installed and evaluated on in-mine machines engaged in regular coal mining operations. This work was performed under contract to the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center. The canopies will support a vertical load of 18,000 pounds and provide protection against both roof falls and contact with the mine rib. Canopy configurations were established based on human engineering studies, full scale canopy mockups, and in-mine observation and consultation with mine and equipment manufacturing personnel. Overall height of each canopy is hydraulically adjustable between a minimum of 32 inches and a maximum of 40 inches. Canopy tops are open framework, welded structures, covered with expanded metal mesh. Structural members are 1 3/4-inch or 2-inch square tubing of AISI 413ON and ASTM A500 material, respectively. The canopy tops are typically supported by an understructure and upright post arrangement that is either integrated into the current operator platform or attached to the machine frame. The four upright corner posts house the hydraulic actuators. Canopy tops are elevated horizontally. Canopies are welded or bolted to the existing machines. Installation is accomplished with a minimal amount of interface modifications. No major machine design changes are required. Canopies were trial installed and load tested at the manufacturer's facility prior to installation on the in-mine machines. Canopies were installed on a Joy 14BU10 Loader, 16RB-3AH Cutter, and two 21SC Shuttle Cars, and a Galis 300 Roof Drill and 460-S Face Drill. Canopy installations were evaluated in the Jewell Ridge Coal Company No. 12 and Big Creek Tiller Mines. Operational time accumulated on the installations during evaluation ranged from 1 week to 14 weeks of two-shift operation. All five canopy designs, manufacture, and test were successfully accomplished. The five canopies met all safety requirements. Three of the five canopies were deemed to be completely successful from an operator's point of view. That is, mine management as well as the machine operator found that the canopies did not impede the operation of the machines to function with the same efficiency as before the installation of the canopies. The loader canopy, in fact, appeared to have provided a mole efficient operation of the loader by providing added safety to the operator from rib contact thus allowing him to concentrate more fully on the loading function. Operational problems were encountered with the shuttle car and the roof drill. The shuttle car canopy obstructed visibility to an objectionable amount and the roof drill canopy impeded maneuverability of the machine, more than doubling the roof bolting time.

Jan 1, 2012

By E. C. Lane

[The motor gasoline that s being marketed in the United States this summer slightly more volatile then that sold a year ago. This increase in volatility is shown by a general lowering ref the average distillation rang, of about 2°F. During the post 10 years the Bureau of Mines has made semiannual surveys of the gasoline marketed in the United States, the survey just completed being the twentieth in the series. The 12 cities in which samples were collected have beer chosen as representative of the more important marketing territories, as it is obviously impracticable to obtain a sample of every gasoline sold in the entire country.]

Jan 1, 1929