Search Documents

By M. J. Pazuchanics

This U.S. Bureau of Mines report presents results from an ongoing investigation of the use of adaptive signal discriminating methods to distinguish between cutting coal and cutting mine rock. Bit-cutting forces and tool vibration were measured in the laboratory as a linear-cutting apparatus (LCA) made constant-depth cuts in coal, sandstone, and shale test specimens. A portion of the collected data has been analyzed and some preliminary results are given here. The influence of data bandwidth, data window size, number of signal features, and voting among classifiers on classification performance are noted. Results to date, based on ideal-cutting conditions and simple geologic materials, indicate that of the four classifiers tested there appears to be no single best classifier. Usually, classification accuracy showed slight improvement as the number of features considered for classification increased. The highest classification accuracies were achieved when voting was conducted among classifiers followed by voting among force components.

Jan 1, 1991

By Carlton E. Brown

Impinger dust-counting methods are used by industrial hygienists for determining the number concentration of unhygienic siliceous dusts in industrial atmospheres. Various statements have been made regarding the size of the smallest particles revealed by the microscopic employed in such determinations. Published data on the subject are quite limited. This report presents information on the size of the smallest particles revealed by light-field and dark-field techniques applied to impinger and electric precipitator samples collected from experimentally established aerosols of silica dust and bituminous-coal dust. Size distribution and number concentration of particles of the various sizes in the aerosols were determined from samples collected by thermal precipitation simultaneously with the impinger and electric precipitator samples. The size of the smallest silica and bituminous-coal dust particles determined in the light-field counting method used was about 1./1, . There was relatively little variation in the values from 8 impinger and 33 A.-C. precipitator samples of silica dust and 13 impinger and 13 A.-C. precipitator samples of coal dust. The coefficients of variation of the values from the four sets of determinations were low, ranging from ± 7.7 to t 10 percent. This size of 1,14 is close to the limit of resolution of the microscopic method used and to various previously suggested values. The size of the particles determined in the dark-field counting method used was smaller than the size (about 0.28A ) of the smallest particles determined in the light-field, oil-immersion method used for the thermal precipitator samples.

Jan 1, 1951

By Nan Wang

Based on the commercial computational fluid dynamics software, Fluent, a three dimensional finite-volume model has been established, and the fluid flow and heat transfer in the super-wide slab mold (cross section 3250mm×150mm) of Nanjing Iron and Steel Company has been simulated. The basic feature of flow and temperature field in a super-wide mold has been analyzed, and the effects of mold width, the submergence depth of SEN, outlet angle of SEN, casting speed, superheat and cooling rate on the flow and temperature field have been investigated. The results by comparing several simulated calculations for 3250mm×150mm slab show that a more proper fluid flow and temperature field in the super-wide mold can be obtained with 15°outlet angle, 120~150mm submergence depth of SEN and 1.2~1.4m/min casting speed. The results through numerical simulation provide a theoretical basis for optimizing the configuration design of SEN and choosing reasonable processing parameters for the continuous casting mold of super-wide slab.

Jan 1, 2009

By R. Hogg, T. H. Dumm

"The mathematical treatments used in the evaluation of particle size distribution from pipet-withdrawal centrifuge data are reviewed. An error in the published procedure for multiple-sample withdrawal systems is pointed out and a corrected formulation is presented. An alternative treatment, based on a piece-wise linearization of the size distribution is described. Computer simulations of the analytical and data evaluation procedures indicate that the errors in the original formulation are not generally serious and that the corrected and alternative procedures lead to very similar estimates. Except for some cases involving very narrow size distributions, the alternative approach appears to give slightly closer estimates of the size distribution. Comparisons based on actual experimental data are also described.1 IntroductionSedimentation methods are widely used for the determination of particle size distributions. The procedures are relatively simple to use and the results are essentially absolute, requiring no external calibration. Gravity sedimentation is typically applicable to particles in the size range of about I to 50 pm and generally involves measurement of the relative concentration of particles as a function of depth and time in a dilute suspension. Particle size is calculated using Stokes, law:"

Mar 1, 1989

By Lewis C. Karrick

Although the Bureau of Mines has thus far made no large-scale experiments with oil shales, and the feasibility of the commercial manufacture of shale-oil products suited to present market requirements has not been demonstrated, there is ample reason to believe that these products will eventually supplement the more commonly used petroleum products and give equally good service. In 1919 the bureau, in cooperation with the Department of Metallurgical Research, University of Utah, began investigating the oil shales of the United States to obtain detailed information on their value. The States of Colorado and Indiana also cooperated through their State universities, in which research laboratories were organized to assist in carrying on the oil-shale studies planned and directed by the bureau. As a result of these studies much information is now available concerning laboratory methods of producing the greatest yields of the best products from oil shale. In order to study the principles that govern the retorting of oil shales and to test the oils produced, it has been necessary to develop and standardize reliable apparatus and methods for distilling shale, and to adapt to the testing of shale oils some of the methods the Bureau of Mines uses for testing petroleum. The methods employed by the Scottish shale-oil manufacturers were also studied, but most of them have been superseded by those described in this bulletin, which give more comprehensive and accurate results and employ more convenient apparatus. This paper is presented, therefore, as a manual of apparatus and methods that the bureau has developed for work on oil shale and found satisfactory for routine tests and for research. Explanation and discussion of the principles underlying the methods of testing are included wherever necessary for a clearer understanding.

Jan 1, 1926

By John L. Lamont, Walter Crafts

ADEQUATE hardenability has long been recognized as one of the first requirements for producing desired mechanical properties in a heat-treated steel. Since the introduction of the Jominy end-quench test1 and the development of correlative information to expand its use, industry has had an effective measure of hardenability. Prediction and control of the hardenability have been made possible by Grossmann's principle2 for calculating hardenability from chemical composition; and Field's conversion3 from depth of half-martensite hardening to Rockwell C hardness has made the relation more quantitative. These developments have facilitated the design of new steels and the control of standard grades to the extent that it has been possible to establish tentative hardenability bands for some of the more commonly used alloy steels.4 As the depth of hardening of the Jominy test specimen is usually measured by Rockwell C hardness, it was considered that it should be possible to predict the hardness by a more direct calculation. It has been found that this can be accomplished by the addition of Rockwell C units proportional to the carbon and alloy content, grain size, and position in the Jominy test specimen. The calculation has been found to be fairly accurate, and because of its additive character is relatively simple to use. In principle the method of calculation is somewhat similar to the expressions developed by Herty, McBride, and Hollenback,5 Burns, Moore, and Archer,6 and Burns and Riegel.7 The calculation is started from a base that includes the effects of carbon content and position in the Jominy test speimen. Rockwell C units are added to the base in proportion to the alloy content and grain size. This sum represents the Rockwell C hardness up to the level at which a disproportionate increase of hardness is caused by the formation of martensite, and above this level an increment for martensite hardening is added. The effects of alloys are directly proportional to the amounts present and are independent of each other, the carbon content, and the position in the specimen. Furthermore, the factors for determining the martensite increment are dependent only on carbon content and are independent of cooling rate and alloy content. It is this absence of interrelation between the different factors that makes it possible to calculate the hardness and makes the method of calculation consistent with the principle that the character of the hardening reaction is governed primarily by carbon and that alloys exert their effect chiefly through control of the critical cooling rate. The principle of the calculation, and the effects of alloys on the critical cooling rate,

Jan 1, 1945

By G. W. Weems

The Bureau of Mines used the Burnett method and apparatus to determine the compressibility factors for helium and carbon dioxide mixtures at 0°, 10°, 20°, 23°, and 35° C and to pressures of 900 psia. Tables of compressibility factors and approximations of the virial coefficients are presented for seven binary mixtures as well as for helium and carbon dioxide. The results compare favorably with existing data.

Jan 1, 1969

By A. Lopez-Valdivieso

Particle size enlargement processes play an important role in solid/liquid separation, and in beneficiation unit operations. In the latter, not only the size of the formed aggregates but also their surface properties are very important. Oil agglomeration has a special place among such processes: it is a selective process in which hydrophobic particles are agglomerated into hydrophobic agglomerates which can be recovered by flotation. This explains the broad applications of oil-assisted beneficiation processes not only in the beneficiation of fine coal, but also in agglomerate flotation of many different types of ores, and in coal/gold agglomeration.

Jan 1, 2004

By M. Jackson, R. McDonald, T. Osken, D. Robinson

"The addition of sulphidic materials in the leaching of nickel laterites has several potential benefits that include improvements in the rheological behaviour of the blends, reductions in the sulphuric acid and steam requirements, sweetening of the nickel grade of the combined feed material, and the option of using a range of sulphidic materials. The current study examines the oxidative processing of 30% w/w blends of nickel concentrate and nickel laterite ore at 250oC. In particular, the viability of using low oxygen overpressures was examined for significant amounts of nickel flotation concentrate, up to 12% w/w. Further to this the impact of process water quality, in particular the presence of chloride, upon the kinetics of extraction and the mineralogy of the residue were also investigated. This paper will present the results of preliminary work in this area.INTRODUCTIONThe use of sulphidic ore as a source of sulphuric acid during oxidative hydrometallurgical processing is not a novel idea and can be traced back over forty years (Seidel & Fitzhugh, 1968). A series of patents pertaining to application of this approach for laterite ores can be subsequently found (O’Neill, 1973; Opratko et al., 1974; Rodriguez, 2008a, 2008b; O’Callaghan, 2010; Liu et al., 2011) and a few of articles containing published data (Ferron & Fleming, 2004; Quinn et al., 2009). The use of pyrrhotite tailings as a source of sulphuric acid has also been employed for the leaching of converter slags (Perederiy et al., 2011).It is known that hydrometallurgical operations such as the HPAL plant at Murrin Murrin have added small amounts of sulphides as either transitional (mixed sulphide/oxide) ore or non-smeltable concentrate. This can improve the rheology (Rodriguez, 2009) and provide heat credits. However these plants are generally limited in their ability to add such materials due to their reducing nature and given under highly acidic conditions that the breakdown potential of the titanium used for the autoclave lining is significantly reduced. A suitable oxidant must therefore be present to ensure the potential remains sufficiently high."

Jan 1, 2012

By D. K. Steele

The domestic primary copper industry generates in excess of 600 million t of mining and mineral-processing waste annually. Most of the waste poses negligible environmental threat, but a small fraction, because of toxic or corrosive characteristics, may be subject to regulation under Subtitle C of the Resource Conservation and Recovery Act (RCRA) or other pertinent regulations. Among the wastes generated by various copper producers are flue dusts, slags, refinery-bleed solutions, and. acid-plant wastes. The U.S. Bureau of Mines (USBM) has researched methods to mitigate the environmental threat posed by copper-processing wastes while recovering valuable metals from these materials. Acid-leach processing of flue dusts has been demonstrated feasible along with sulfide treatment of liquid refinery wastes and acid-plant-bleed and gas-cleaning solutions to precipitate dissolved metals. In, addition, the feasibility of removing copper and molybdenum from slag, as well as stabilization of precipitated sulfide wastes by vitrification, have been investigated.

Jan 1, 2010

By Lennart Bergstedt

Boliden Aktiebolag, the prime base metal mining company of Sweden, annually treats some 11-12 million tons of sulphide ore in nine concentrators. Its first flotation plant was established in the early thirties for the complex Boliden ore. Since then, the number of mines and plants has gradually increased. Considerable effort has been devoted to the development of all phases of the technology of ore prospecting, mining, milling, smelting and refining. This has been necessary due to the complex and low-grade ores. The development of concentration has mainly been directed toward the arts of grinding and flotation. During the forties and fifties, open-stage fine crushing followed by two-stage grinding in rod and ball mills with cyclone classification was successfully introduced and used throughout the plants. The increasing cost of grinding media led to studies of an autogenous grinding technique as early as 1945. Basic test work commenced during the early fifties, with a. number of ores tested for pebble grinding. In 1956 a new pilot plant was built, with equipment installed for the continuous testing of pebble grinding and, later, for primary autogenous grinding of run-of-mine ore. The intensive test work showed that pebble grinding was feasible in almost all of the plants. At this early stage of testing, however, the merits of autogenous grinding could not be fully evaluated. As a. consequence the rod mill/ball mill grinding systems were converted to rod mill/pebble mill systems whereever possible. In parallel with the converting of grinding systems the development work concerning the merits of autogenous grinding went on. The major result

Jan 1, 1977

By D. F. Suarez

Spontaneous nodulation leading to growth of well developed glossy spheroids (generally hemispheres) of up to 0.06 cm width in 120 min has been observed during copper electrodeposition with certain levels of glue, thiourea and C1-. Thiourea alone can produce spontaneous nodulation but addition of glue and/or Cl- is required for rapid and sustained growth. In most cases once the glossy nodules develop they consume the majority of the copper deposited; thus, the specific current densities (and hence copper electrodeposition rates) on the glossy nodules are about an order of magnitude or, more greater than on the adjacent planar surfaces. The texture of the adjaoent planar surfaces is not glossy in appearance but is well faceted showing the usual deposition grain structure for such additives. Cathode potentials when spontaneous nodulation occurs are about TOO my more negative than with usual copper electroplating. This fact associated with evidence of extremely high levels of cathode surface passivation based on cyclic voltammograms indicates that the conditions which lead to spontaneous nodulation result from a very tightly adsorbed additive surface film. This film breaks down in specific points initiating the glossy nodules which then grow at extremely rapid rates. Current density is also important in spontaneous nodulation. At equal deposition times a current density of 21.5 mA/cm produced much larger glossy nodules than at 48 mA/cm2. The surface concentration of the glossy nodules was much greater in the latter case, however. The role of current density is still not well understood. The role of it as well as the relative roles of the three additives, thiourea, glue and Cl- in spontaneous nodulation is presented. Preliminary results and some possible correlations of these to help explain spontaneous nodulation are presented. It is believed that tankhouse upsets where cathode nodulation occurs may be related to this phenomenon.

Jan 1, 1987

By M. S. Celik

The principal impurities in some feldspar ores are titanium and iron which impart color and in turn degrade the quality of the ore. The mineralogical investigations indicate that titanium element originates from mainly rutile with small amounts of sphene. Conventionally, fatty acids and particularly sodium oleate are extensively used in the flotation of colored minerals from feldspar ores with reasonable success. In this study, new reagents, oleoyl sarcosine and hydroxamate have been used to float colored impurities before and after magnetic separation. Oleoyl sarcosine is found to exhibit better results compared to fatty acids and hydroxamate. The mechanism of the action is elaborated on the basis of experimental data.

Jan 1, 1999

By Zhihe Dou, Yan Li, Qiuyue Zhao, Guozhi Lv, Yan Liu, Hongliang Zhao

"Abstract: How to reduce carbon dioxide emissions has become a vexing problem, meanwhile, there exist high energy consumption and low efficiency problems in the existing CO2 capture and storage technologies. For CO2 comprehensive Utilization, this paper researches a new technology of absorbing the CO2 emission with high alkaline calcium or high alkaline wastewater sludge mineralization of calcium and invent a core device for multi-level jet carbonation. The industrial test has been carried out in China Xinyu slag Engineering Co., Ltd. The wastewater flow is 150m3/h in the pilot scale. The prepared calcium carbonate has a whiteness greater than 90%, particle size less than 150nm. The mineralization of aluminum exhaust with waste carbide indicates that the CO2 absorption rate is greater than 99.0%, CO2 concentration in the exhaust gas is lower than 0.08%, the purity of mineralized calcium carbonate is greater than 99.0% and particle size is less than 100 nm.InstructionAccording to the statistic data from IEA (2009), the carbon dioxide discharge from fossil fuel consumption in China has exceeded it in the US by the year of 2007, China, has become the largest emitter of carbon dioxide all over the world. Meanwhile, the economic scale is still on an increasing trend in the next 50-100 years, leading to a continuous increment in carbon dioxide discharge. According to the international energy agency forecasts, the energy-relative CO2 discharge in China will rise to 11,615 million tons, 91.3% higher than it in 2007. In the year of 2012, the CO2 gross discharge has reached 10,000 million tons, obviously higher than the predicted value. It is a tremendous task to reduce the emission. Non-ferrous metals industry is one of the largest emitters of carbon dioxide among the industrial circle, the whole industry might discharge a huge amount of carbon dioxide (over 600 million tons), in which the electrolytic aluminum industry is the largest energy consuming industry and CO2 emitter. At present, the CO2 discharge has focused by the whole world due to the environmental problems it causes; meanwhile, supplement of new carbon source is needed due to the exhausting oil and coal resources, so that various countries in the world are attaching importance of the recycle and purification of CO2. Many countries are studying on the cyclic utilization of carbon dioxide. Gas CO2 is mainly applied in chemical, pharmaceutical raw materials, beverage filling agent, refrigerant, inert medium, solvents, pressure source, the welding protective gas, antioxidant and fire extinguishing agent, etc. Solid CO2 is mainly applied in penicillin production, fish, cream, ice cream and other food storage and transportation at low temperature, etc. nowadays, such methods as absorption method, membrane separation, adsorption, etc. are widely used to recycle CO2, with such problems as high investment cost and technical constraints etc."

Jan 1, 2014

By R Ayothiraman

Tunnel excavation may induce adverse effects on nearby existing structures/foundations in urban areas. Accurate prediction of tunnelling effects on pile foundations of nearby structures in the urban environment poses a major challenge during design. Several studies have been undertaken to understand the mechanisms of the soil-tunnel-pile interaction, which focused only on influence of tunnelling on nearby existing building and foundations. However, effect of pile loading on existing tunnels did not receive enough research attention so far. So it is essential to measure the response of existing tunnel-lining due to loading on newly constructed pile to assess to the safety against the additional forces/moment caused by pile loading and to evaluate the critical distance for the proposed construction of any structures from the tunnel location. This paper presents result of three-dimensional (3D) finite element analysis carried out in ABAQUS to investigate the effects of pile loading on existing tunnels embedded in cohesive soil. It is found that the effects on tunnel lining depend on horizontal separation distance between pile and tunnel as well as location/elevation of pile tip with respect to tunnel location.

Mar 8, 2011

By William E. Lamont

The Mineral Resources Institute (MRI) of the School of Mines and Energy Development (SOMED), University of Alabama conducted studies to determine the potential for upgrading the Eastern Devonian shales by flotation. Results of those studies indicate that flotation concentrates containing 150 liters of oil/t (36 gal/t) can be produced from shale containing 50 liters of oil/t (12 gal/t) as determined by Fischer Assay with good recovery of the kerogen. Organic carbon and trace elements such as molybdenum, vanadium and uranium also are concentrated with the kerogen. Kerogen concentration was found to be a function of the size of grind.

Jan 1, 1983

By A. Uiga

The U.S. Bureau of Mines funded a project which addressed objectives concerning irrigation of native plants and inoculation of native plants with vesicular-arbuscular mycorrhizal (VAM) fungi. The specific irrigation objectives were 1) to demonstrate the performance capabilities of solid-set irrigation for reclaimed mineland conditions, and 2) to demonstrate and evaluate three irrigation concepts under two separate water supply conditions. The VAM inoculations were to assess irrigation benefits in establishing VAM relationships for transplanted native species. Following the seasonal demonstration (May to September 1983) at 3 separate mine sites, conclusions were made that apply to the 6 state Western mining industry. The demonstration sites were located in Montana, Wyoming, and New Mexico. Positive conclusions were reached for 1) the use of soil moisture sampling with or without irrigation, and 2) the selection of solid-set sprinklers as the irrigation method. The conclusions about the irrigation concepts and strategy were mixed, due to the short-term (1 season) nature of the project. No conclusions could be reached for the VAM inoculations because the study time was too short.

Jan 1, 1984

By Dapeng JIANG, Haixiao YANG, Shanxi WU, Jinwang Zhang, Guoliang XU, Yipeng ZHANG

The subsidence and deformation characteristics of strata with thick unconsolidated overlying strata is quite different from that with consolidated overlying strata. In this paper, based on the engineering background of large mining height mining in No.21 coal seam of Zhaogu No.2 Coal Mine in Henan Province, China, the PFC 2D numerical simulation and surface subsidence field observation was conducted to study the subsidence characteristics of strata with thick unconsolidated overlying strata (680m). Numerical model with dimensions of 2000m 750m was established and mining process with different working face lengths (150 m,200 m,250 m,300 m) and different working face advancing distances (40 m,80 m,120 m,160 m,200 m,240 m,280 m,320 m,360 m,400 m,440 m,480 m) were simulated. The surface subsidence characteristics and displacement field variation of rock strata under different working face advancing distances were observed and analyzed. The results show that with the advance of working face, the structure of subsidence-like basin will be formed in each rock stratum, and the influence range of mining on rock stratum is “bowl-shaped”, and the influence increases with the increase of advancing distance. The unconsolidated layer has a buffer effect on the mining-induced subsidence, and the buffer effect is realized by the expansion of the subsidence area. The movement law of strata under different working face lengths is similar to that under general mining, and the structure of subsidence-like basins will also be formed in each stratum. The influence range of strata after mining is ' bowl-shaped ', and the influence extent increases with the increasing of working face length; the internal subsidence of the unconsolidated layer is more intense and complex than that of the rock layer; the surface subsidence movement shows an obvious 'basin' phenomenon. The field observation data of surface subsidence also confirm the above results.

By H. D. Hess

This report presents the results of laboratory mineral evaluations conducted by the federal Bureau of Mines under the joint sponsorship of the U.S. Atomic Energy Commission (AEC) and the Bureau a! Ships, U. S. Department of the Navy. The major purpose of this investigation was to examine and evaluate zirconium minerals representing sizeable deposits in an effort to locate com¬mercial sources of high-hafnium ores. Although determination of the hafnium content was the principal objective, each of the zirconium minerals also was analyzed for combined zirconium-hafnium oxide, silica, uranium, thorium, yttrium, and cerium. The general laboratory procedure involved microscopic examination of the test samples, concentration of the hafnium-bearing zirconium mineral by standard laboratory techniques, and analysis of the derived concentrate by quantitative microscopic, chemical, and X-ray spectrographic methods. Of the several hundred samples tested under this program, 147 are discussed in this report, including 94 from domestic occurrences and 53 from widespread foreign sources.

Jan 1, 1962

By E. A. Hewitt

This paper describing the mining practices at the Park Utah mine in the Park City district is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Park Utah mine is situated at Keetly, Utah, about 5 miles east of Park City. The Park City district lies on the eastern slope of the Wasatch Mountains, 25 miles southeast of Salt Lake City. The district embraces a tract located between the crest of the main range on the west and the mountain meadows along the eastern foothills. The elevation of the Union Pacific Railroad station at Park City is 7,000 feet above sea level. The town and mines are served by two railroads; one 28 miles long is a branch of the Union Pacific Railroad and connects with the main line at Echo Junction, east of Ogden; the other is 35 miles long and joins the Denver & Rio Grande Western Railroad at Salt Lake City. The district and mines are also accessible by excellent automobile roads from Salt Lake City and surrounding points (fig. 1).

Jan 1, 1930