Search Documents

By J. Stowe

While there has been continual improvement in the models for predicating deposition velocity and pipeline friction losses, the fundamental design philosophy for tailings pipelines has remained the same over the previous three or four decades: design the tailings pipeline to operate in turbulent flow without a deposit on the pipe invert for all expected process conditions. Recent improvements in the understanding of slurry pipeline flows allows for the design of pipelines operating with a deposit on the pipe invert, allowing the system to operate at moderate velocities for high flow rates, optimizing system energy requirements and maximizing pipeline wear life. Tailings pipelines are increasingly operated at higher solids concentrations where there is a greater likelihood the pipeline will operate in laminar flow due to the higher tailings slurry rheology. Historically, slurry pipelines have been operated in turbulent flow. We now know that laminar flow pipeline operation is possible as there are several operational laminar flow tailings pipelines. While our understanding of laminar flow slurry pipelines is not complete, recent research provides guidance on how to approach the design of these pipelines. New sensor technology has led to the development of an instrument that provides reliable indication of bed deposit height within a pipeline. This technology is particularly helpful in operating pipelines with a deposit and has application in better understanding the operation of laminar flow pipelines. Failure of tailings pipelines can result in consequent damage to surrounding structures and unacceptable spillage into the environment. Modern pipeline leak detection technology allows operators to better manage this risk by ensuring safe and reliable operation of tailings pipelines. This paper provides an overview of the each of the above advances in the design and operation of tailings pipelines. OPERATING TAILINGS PIPELINES WITH A DEPOSIT Tailings pipelines, and slurry pipelines in general, are typically designed to operate without a deposit on the pipeline invert. Meaning, the minimum operating velocity exceeds the turbulent deposition velocity. This approach has been adopted due to concerns regarding potential blockage of a pipeline operating with a deposit. Figure 1 shows a typical design duty envelope for a tailings delivery system as a function of solids throughput and solids concentration by mass. If the pipeline is designed to operate without a deposit at the lowest duty flow rate (4,480 m3/h), the operating velocity at the highest duty flow rate (6,590 m3/h) is about 1.5 times the deposition velocity. Considering that the pipeline wear and energy requirements are roughly proportional to the square of operating velocity, this results in an operationally inefficient system when the pipeline is operated close to the maximum design flow rate. Most systems tend to operate at maximum throughput after post-startup debottlenecking optimizations. Alternative Approach An alternate design approach is to ensure the pipeline operates without a deposit for the nominal flow rate and accept that a deposit will form when operating at lower flow rates. This results in the selection of a larger diameter pipeline, but there are significant benefits in terms of reduced energy requirements and lower pipeline wear.

Jan 1, 2019

By D Cooke

In 2010, Kalgoorlie Consolidated Gold Mines (KCGM) was Australia’s largest gold producer, with total annual production of 788 000 ounces. Of the gold produced by KCGM in 2010, 95 per cent was extracted from the Fimiston open pit, also known as the Superpit. The Fimiston operation encompasses the historic Golden Mile, from which more than 55 million ounces of gold have been extracted from the world-class Fimiston lode style mineralisation.The operational performance of the KCGM Fimiston open pit was reviewed for the period between 2005 and 2010. Key performance metrics reviewed included mined tonnes and grade, cost per ounce of gold produced and the mine to mill reconciliation trends. The years 2007 and 2008 were characterised by a decline in performance against key performance metrics. The ore zones were diluted, with the excess tonnes mined resulting in lower grade and an increase in the cost per ounce. Poor reconciliation between ore mined, the ore reserve model and the grade control polygons was also observed.A series of improvement initiatives were implemented in late 2008. As a result of changes made to the grade control and mining practices, the site performance recovered. Unplanned dilution was reduced, which had a positive impact on mined grade. The lower tonnes combined with higher grade reduced the cost per ounce to below budgeted levels in 2009 and 2010, enhancing the profitability of the operation. The operational performance between 2005 and 2010 was compared to the turnover statistics for the KCGM geology department over the same period. Turnover accelerated between 2005 and 2007, peaking at an annualised rate of 43 per cent. With the onset of the Global Financial Crisis and the implementation of retention initiatives, turnover reduced significantly between 2008 and 2010. A strong consistent correlation was observed between the turnover trends in geology and the performance of the grade control function and resultant site metrics.The cost of turnover is known intuitively, however, rarely quantified. To evaluate the benefit of the improved performance, a detailed financial model was used to quantify the impact of the grade control function. In 2010, the headgrade exceeding budget by just four per cent contributed an additional A$24 M of value to KCGM. In contrast, if the 2008 performance had been replicated in 2010 (-9 per cent on headgrade), the result would have removed A$61 M in value from the business. The KCGM experience between 2005 and 2010 demonstrates the value of human capital in a mining operation and the importance of a high performing geology grade control team to the profitability of a mining operation.

Aug 22, 2011

By George S. Rice

THE A.I.M.E. Ground Movement and Subsidence Committee, pro- posed in 1920, held its first technical meeting in February 1923, under the able chairmanship of Mr. H. G. Moulton. The following list of papers and discussions, indicating the scope of the problems and relation to various conditions and method of mining, were given at that meeting by the distinguished mining engineers: J. Parke Channing, on Subsidence at Miami, Arizona; Howard N. Eavenson, on Mining an Upper Bituminous Seam after a Lower Seam Has Been Extracted; J. J. Rutledge, on Subsidence in Two Oklahoma Coal Mines; Benjamin F. Tillson, on Caving Cracks at the Franklin Mine, New Jersey; Dr. F. W. McNair, on the Dome Theory; William Kelly, on disadvantageous effects in Mining and Back-filling Working Upward a Steep-Pitching Iron-ore Bed; Eli T. Conner, on the good results of Back-Filling by Hydraulic Means in Preventing Destructive Subsidence in the Anthracite District; Thomas H. Claggett, on the merit of Systematic Pillar Drawing in Preventing Cracks in an Upper Seam; Henry H. Otto, successful results in the anthracite district in Mining Lower Seams before Upper Seams; Douglas Bunting, on Leading Factors Incident to Successful Mining of an Overlying Seam; Edwin Ludlow, on there being "less damage to buildings when there was complete removal of coal with complete packing than when room and pillar is used without extracting the pillars"; Edward O'Toole on "bumps" in eastern Kentucky mines, which he thought were the result of geologic stresses: H. A. Buehler, on Upheaval of Surface in an Illinois Case in Advance of the Face; and R. Dawson Hall, on The Mechanics of Subsidence from Mining. The author of this paper discussed various kinds of problems of ground movement and subsidence in both metal mining and coal mining; the production of great landslides by workings near an outcrop, as at Turtle Mountain, Alberta, Canada; and general

Jan 1, 1939

The mineralised members of the Brockman Iron Formation mined at Mt Whaleback are overlain and underlain by shale horizons. To maximise resource recovery, waste movement within the life of mine plan includes mining of the:unmineralised banded iron formation (BIF), Mt Whaleback Shale, Mt McRae Shale, Mt Sylvia Formation, and parts of the Wittenoom and Jeerinah Formation. With the exception of BIFs, all other units contain zones with varying amounts of sulphides and carbon û æreactive shaleÆ. Reactive shale has a propensity to self-heat and can react with some explosives, resulting in spontaneous explosion. Sulphide rich zones also have the potential to generate acid rock drainage (ARD). Mining reactive shale at the Mt Whaleback mine must be undertaken in a safe, efficient and environmentally responsible manner. Key tasks in the mining process include:100 per cent identification of blastholes that may contain reactive shale; 100 per cent correct loading of blastholes with specified blasting products; 100 per cent of reactive shale mined, hauled and dumped in designated overburden storage areas; 100 per cent containment and treatment of ARD water onsite; and ongoing research into ARD, self-heating and spontaneous combustion. Successful mining of reactive shale requires constant co-ordination between the geology, mine planning, mining and environment departments.

Jan 1, 2002

By Andrzej Frycz

The development of the theory of reliability creates more and more possibilities of its application in different domains of technics. The methods evolved to date, both theoretical analysis of the engineering systems and investigations techniques in practice can be put in use a d translated from one science to another one [1,3,7J . It needs to consider the specific of the different sciences. But it is necessary to take account of the specific characteristic of each line of science. The reliability investigations needs, justified in technical and economical viewpoint appear too in mine ventilation technics and systems. The mine ventilation system is a complex of workings and ventilation plants, which serve to supply the networks with a sufficient quantity of fresh air from the atmosphere and then carry off the vitiated air. The condition necessary for a ventilation system to perform definite task is the correctness of all its elements, that is a capability to preserve in a expected range of tolerance, the values of basic parameters. The element of a system which ceases to work correctly is called failed. The basic parameter of all elements of a ventilation system is the characteristic curve, pressure loss - air quantity relation ?p = f(Q) (1) This curve concerning the workings and ventilation stoppings is given by the formula: ?p = R Q2 (2) thus the resistance R (of the workings or stoppings) may be taken as a characteristic parameter. The course of this characteristic f(Q) will be given in a complex form in concern with fans, ejectors, air curtains. The failure of a ventilation plant or working is therefore an event, relying on a change of its characteristic, thus for a definite time the losses of the plant's or working's capability set in for the fulfilment of its function in the ventilation system. The failures are divided in viewpoint of their nature on sudden and progressive. We are in concern with the sudden failures which are characterised by a violent change of the ventilation element parameter for example a fall of roof, or silt up of the working, opening or failure of the ventilation stopping, the stand-off of the fan or ejector etc. We distinguish two kinds of failures on the viewpoint of their action on the air flow: the "opening" failure and "closure" failure. The prevalence of factors, which causes the failures is in connection with the intersection in the mine of roads of haulage, roads of underground transport of materials and lining elements, roads of people motion with airways, as also depends on the rock pressure reaction on the workings lining and plants placed there. Other factors will yet be decisive upon supply decay of fans, ejectors and curtains. The appearance of failure of the ventilation element is therefore of random nature and determines the change of the element, when it is passing from operating state to unoperate. Qualifying the ventilation system element to one of these states is easy, when the characteristic change is clear and occurs suddenly, that was assumed. The investigations conducted by Patrushev and Karnaukh [91 in concern with the ventilation stoppings resistance change in the case of their opening, had shown the possibility of resistance value change in the range of several hundreds higher.

Jan 1, 1980

By B. Listerud, G. Zhan, M. A. Jones

Barrick Goldstrike Mines Inc. (BGMI) operates the Betze-Post openpit and the Meikle and Rodeo underground mines. Because the majority of the orebody is located below the water table, mining at BGMI requires a significant dewatering program. BGMI has a comprehensive dewatering and water management system that experienced a peak dewatering rate of 4,400 L/s in the mid 1990s. Changes to the hydrologic/hydrogeologic system caused by the mine dewatering have been monitored by an extensive network of groundwater monitoring wells and surface water monitoring stations, which cover about 1,550 km2. In addition to the monitoring program, a new tool, called Interferometric Synthetic Aperture Radar (InSAR), has also been used to enhance the evaluation of changes. Finally, a groundwater flow model has been developed that successfully simulates and predicts aquifer responses in the mine area and region. The well-calibrated flow model has served as a reliable tool to develop dewatering and mining plans, and project post-closure hydrologic conditions in the region. This paper introduces the BGMI dewatering and water management system and the means used by BGMI to evaluate and anticipate hydrologic responses in the region. The water management and analysis system has been and continues to be an integral part of managing ongoing operations, planning and pricing out future activities and evaluating the long-term effects of mine water handling.

Jan 1, 2011

By Francisco Gil Coury

Ligas Al-Mn-Ce são de grandeinteresse por formaremfases e microestruturasde aplicação promissora, como quasicristais, fase amorfa e ligas cristalinas de alta resistência. Entretanto, pouca atenção foi dada àdeterminação do diagrama de fase desse sistema. Este trabalho apresenta uma avaliação termodinâmica preliminar das fases ternárias Al8Mn4Ce e Al10Mn7Ce2, compostos da região de maior interesse deste sistema:as composições ricas em Al. A avaliação termodinâmica foi feita considerando os dois compostos como fases estequiométricas. A energia livre destas fases foi estimada a partir de dados experimentais obtidos por análise de calorimetria diferencial de varredura, microscopia eletrônica e difração de raios X e as seções isotermas existentes na literatura, empregando ligas obtidas por fusão a arco. Os resultados indicam que foi possível produzir as fases de interesse pela metodologia proposta, e que os parâmetros estimados para a energia livre de ambas as fases permitem reproduzir adequadamente secções isotermas do diagrama ternário em diferentes temperaturas.

Aug 16, 2017

F. G. SMITH.-Probably someone will ask whether I discovered why the bottoms of the large shells broke out. I did not, as a result of this investigation. An experiment was made along the lines indicated in this paper, to determine whether abnormal grains greatly affected the physical properties of brass. Two ordinary test bars were annealed for 1/2 hr. at 750° C. and physical properties determined on one. The other was covered with indentations made with a peen hammer and then reannealed. for 5 hr. at 750° C. It was found in the tensile test to be made up of large grains 1/4 to 1/2 in. in diameter. The physical properties, however, differed from those of the first bar only as much as might be expected after a 5 hr. anneal under normal conditions. It appears then that the large grains produced in this manner do not ruin the physical qualities of the brass.

Jan 12, 1919

By M D. Kuruppu

Fleet operational effectiveness is fundamental to any operation, becoming highly topical in mines experiencing less than optimal output from their fleets. It is an all encompassing aim to identify those factors that could be improved within production and suggesting solutions in order to optimise the existing fleet and obtain the highest return on capital expenditure. The fleet operational effectiveness of a large open pit truck and shovel operation in Western Australia was examined and a study was undertaken allowing identification of areas falling below target. The annualised hours and production downtimes were investigated to quantify the potential gains of improvements in these areas. The project aimed to maximise direct working hours through determination of the main issues hindering performance. External and internal factors were considered and a continuous improvement program (CIP) was developed. The CIP aimed at internal site-based improvement teams to identify and implement solutions for improvement on a day-to-day basis. Strategies were then identified for the implementation of the proposed changes.

Jan 1, 2003

By M. L. Harris

Explosions in underground mines and surface facilities such as processing plants are caused by confined accumulations of combustible dust and/or flammable gas mixed with air in the presence of an ignition source. Underground explosions can be prevented by minimizing methane concentrations through methane drainage and ventilation, by adding sufficient rock dust to inert the coal dust, and by eliminating ignition sources. The effectiveness of rock dust in arresting explosion propagation was proven by experiment and practice (1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11). The precise mechanism by which rock dust (generally pulverized limestone dust) quenches flame has not been fully explained, but is believed to be absorption of thermal energy from the heated gases and absorption of radiant energy, which reduces the preheating of unburned coal particles ahead of the flame front. One measurable aspect of explosibility is incombustible content. In order to determine whether enough rock dust is applied, 30 CFR1 § 75.403, Maintenance of Incombustible Content of Rock Dust, requires at least 80% incombustible content on the roof, ribs, and floor of underground coal mines. 30 CFR § 75.403-1 further defines the incombustible content as follows: ?Moisture contained in the combined coal dust, rock dust and other dusts shall be considered as a part of the incombustible content of such mixture.? In order to determine the incombustible content of the mine dust, samples of deposited dust from specified areas in a mine must be collected, analyzed, and then compared with the minimum standard of 80%. The traditional low temperature ashing (LTA) approach to determine if a coal and rock dust mixture is compliant with the inerting requirement consumes the coal dust and considers the remaining material to be inert. Compliance with the law is then determined by comparing the measured percentage of inert material of the representative band sample with the pre-established requirement of 80%. The incombustible content of the sample includes rock dust, the amount of moisture as received at the lab, and the inherent ash in the coal. The LTA method is not itself a direct measure of explosibility but is a surrogate that calculates a single parameter associated with large-scale Bruceton Experimental Mine (BEM) explosion test results conducted with dry rock dust. This method assumes a homogenous mixture with no layering of rock dust and coal dust. Float coal dust is a serious explosion hazard if it accumulates on top of the rock dust and is not mixed with the rock dust (12). Mitchell and Nagy (13) studied the effectiveness of water as an inerting agent for the coal dust explosion hazard. The study emphasized that surface water evaporates readily from dusts. Thus, in a passageway where the dust is wet, changes in weather or the ventilation system could dry the dust and make it unsafe in a relatively short period of time. Where adequate rock dust has been applied, this drying effect is not a factor. However, if the mine depends upon the moisture content as part of the incombustible content, fluctuations in the dust surface moisture within a mine can render moisture content an ineffective and inconsistent measure of safety. Additionally, if sufficient moisture is absorbed and subsequently relinquished by rock dust, a cake can form and render the rock dust ineffectual. The trend has long been recognized that mine explosions occur primarily during the winter season when the humidity is low for long periods of time (14, 15, 16). In light of this trend and due to the potential variability of the moisture content of the dust, it may not be prudent to include variable surface moisture in the total incombustible content of the sample. Instead, surface moisture should be viewed as an additional safety measure as long as the rock dust is dispersible. However, moisture limits the ability of the rock dust to disperse and can significantly reduce its capacity to effectively inert propagating explosions (2, 13, 17, 18, 19, 20, 21, 22). Given the methods by which the as-received moisture and incombustible content are determined, dust samples from the 2010 MSHA database were assessed to determine the variability of the moisture content throughout a year and how often the measured as-received moisture might have affected the dust explosibility determination if removed. The findings were then verified by observation in laboratory studies and within the NIOSH OMSHR Safety Research Coal Mine (SRCM).

Feb 23, 2014

By Bellairs P, Stewart JC

On 20 December 1983 at 8.40am blast- hole 57 of Blast RN177 prematurely detonated follwed by a violent deflagration of blast- hole 59 at 10.40am. The blastholes were 380mm diameter drilled in black pyritic Mt McRae shale. The blastholes were loaded with ANFO and primed. Blasthole 57 was stemmed and blasthole 59 was not. A poss- ible mechanism which could lead to such a detonation is described. preliminary tests showed the top 5m of a bench had the highest temperature which could not be influenced by a range of treat -ments. Small scale laboratory tests show- ed that zinc oxide (ZnO) and magnesium carbonate (Mg2CO3) inhibited the reaction. A series of tests using AN with and without inhibitors loaded into the collars of blast -holes drilled in the top 6m of the bench and unstemmed is described. An analysis of the time to reaction of the holes loaded with AN against temperature shows that the decomposition of the AN in contact with the black pyritic shale is probably a sulphuric acid catalysed react- ion. All the inhibitors tested can neut- ralise the sulphuric acid in the shale. 10% ZnO appears to be an effective inhibitor of the reaction providing the AN/ZnO (90/10) is kept out of contact with surface material whose temperature can be as high as 60¦C in summer. It is concluded that ANFO/ZnO (90/ 10) should be now tested in stemmed holes.

Jan 1, 1986

By L. A. Bromley, R. L. McKisson

A high temperature calorimeter designed for use up to 1500°K is described and the theory of its operation presented. This calorimeter was used to measure the heats of formation of Na-Sn alloys ranging in composition from tin to Na2Sn. The values tend to support those reported by Kubaschewski and Seith. ONE method of obtaining the heat of formation of an alloy is to measure the heat of mixing of the elements at high temperature. The principal advantage of this method is that the desired quantity is measured directly, while in conventional room temperature methods the differences of the heats of solution of the elements and the alloy in a suitable solvent are measured. A method of improving the accuracy of the high temperature measurements, when the precision of the measurement is lower than that of the heat capacity values for the elements, is to add one component at room temperature to the other at the high temperature, so that part of the heat of reaction is dissipated in heating the cold component to the high temperature. Thus, only a fraction of the heat of reaction is measured, and a result of higher precision is obtained. The limitations of the high temperature technique are that volatile systems cannot be studied, and that many alloys melt at temperatures higher than those at which the calorimetric apparatus operates readily. Nevertheless, a calorimeter operating at 1500°K would be useful in investigating many of the lower melting alloy systems and the low melting mixed oxide systems. A unit designed for these applications was built and is described here. The Na-Sn system was chosen for investigation because the temperature involved, 880°K, would adequately test the operation of the calorimeter. Further, the data reported in the literature for the various alloys of sodium and tin differ markedly, and it was hoped that this investigation would help to fix the values of the heats of formation in this system. Design of Apparatus A detailed discussion of the considerations involved in the calorimeter design is given by Mc-Kisson and Bromley,' and a brief summary follows. Fig. 1 shows a sectional view of the calorimeter. The inner graphite chamber is maintained at constant temperature by means of the circulating molten tin bath in which it is submerged. The tin is contained in a graphite vat. This unit comprises a thermostat whose heat capacity is about 7000 cal per "C. The main heating element consists of a machined graphite spiral with a room temperature resistance of about 1/2 ohm. These parts are separated from the powdered carbon external insulation by the cage, a cylindrical graphite chamber. The electrical insulators and separators, the auxiliary heater spool, and the loading tube liner are made of sintered alumina. The tin vat stirrers, the sample stir-rer, the melt thermocouple well, and the power leads are made of molybdenum. The auxiliary heater is wound with molybdenum wire and serves to compensate for the heat loss up the loading tube. All of the individual components in the high temperature region of the calorimeter will withstand at least 2000°K, and the various contacting materials should easily withstand 1500°K. The external container for the insulating carbon powder is a copper shell upon which copper tubes are soldered to serve as cooling coils.

Jan 1, 1953

By S. Chama, P. Chishimba, Tina Chanda Phiri, J. Machona, S. Parirenyatwa, G. Kaluba, Y. R. S. Hara, D. M. Musowoya

The investigation focuses on leaching of copper (2 wt%), cobalt (0.5 wt%) and iron (2.4 wt%) from complex tailings material from the Democratic Republic of Congo. The highest recovery of copper and cobalt into the leach solution were 78 and 10%, respectively, under direct leaching with sulphuric acid. Higher recoveries (90% for copper and 96% for cobalt) were attained when the material was pre-reduced with coal for 1.5 h in the temperature range of 700–950 °C. The increased recoveries were due to metallisation of all the copper and cobalt which is in the silicate matrix. The effects of pre-reduction temperature and sample to carbon weight ratios were analysed and found to be important in; (i) achieving high recoveries of copper and cobalt and (ii) decreasing the amount of iron in the leach solution. The samples were characterised by atomic absorption spectroscopy and scanning electron microscopy (SEM) techniques.

Mar 1, 2017

By T. M. Berry

In the past few years changes have taken place in shaft sinking. Progress has been made with types of machinery designed, developed, and made available to shaft sinking contractors. This is particularly true of drilling and mucking equipment. Compared with conventional clamshell loading, mucking or loading with a crawler-mounted overshot loader is a new technique for shaft work. There are several methods of clamshell loading. Dravo Construction Co. mounts an air tugger on the clamshell to operate the closing line. The load, or holding line, is attached to the hoist of a crane or whirler at the shaft collar. The clamshell is raised or lowered by the hoist when a signal is given by a bell or light system operated by men at the bottom of the shaft. Two men control the drift of the clamshell with tag lines, pulling it to any position in the shaft for loading, or over the shaft muck bucket for emptying. One man operates the air tugger to open and close the clamshell by means of two lines attached to the operating air valve, just as reins are used to drive a horse. One man operates the signal telling the hoist operator when to raise or lower the clamshell. This method requires two hoisting lines in the shaft-the line from the mine hoist that lifts

Dec 1, 1956

By N. E. Hanna

Originally developed for use in coal mines where on-shift blasting with explosives was prohibited, compressed-air blasting has been used for the past 15 years as a substitute for fixed explosives. With the current commercially available compressed-air systems -Airdox and Armstrong -coal is dislodged by a high-pressure discharge of air from a pressurized shell placed in the coal borehole. In the original systems stationary compressors were mounted on the surface or in the underground ventilated areas. These proved so successful that a mobile compressor unit was developed for use at the working face. Because of the possibility that such a unit might operate in a gassy atmosphere, the Bureau of Mines has investigated the hazards associated with operation under conditions where firedamp could accumulate in explosive concentrations. ACKNOWLEDGMENTS Grateful acknowledgment is made of cooperation of C. E. Carter, H. R. Hiller, R. E. Kennedy, H. Kohn, H. D. Metzinger, J. Mahoney, J. Nickovich, G. So Scott and I. Spolan in the experimental work.

Jan 1, 1956

By D. Diekman

Perlite is not a trade name but a generic term for naturally occurring siliceous volcanic rock. A distinguishing feature which sets perlite apart from other volcanic glasses is that when heated to a suitable point in its softening range, it expands 5 to 20 times its original volume. This expansion is due to the presence of 2% to 6% combined water in the crude perlite rock. When quickly heated above 1600°F (871°C) crude perlite pops in a manner similar to popcorn. The combined water vaporizes and creates countless tiny bubbles in the heat softened glassy particles. It is these tiny glass sealed bubbles which account for the amazing lightweight and other exceptional physical properties of expanded perlite. The bulk densities of the expanded perlite generally range from 3 pounds per cubic foot (48 Kg M3) to 10 pounds per cubic foot (160 Kg H3).

Jan 1, 1985

By W. C. Winegard, C. J. Simpson

BNINGESSNER et al.1 have shown that the solidification substructure in dilute cadmium alloys persisted after repeated deformation, recrystallization, and annealing treatments. On the basis of this and similar evidence, Whelan has suggested in a recent publication' that the solidification structure might affect the mobility of grain boundaries even after primary re-crystallization. This suggestion is important, since the technique used by previous investigators3-5 to fabricate grain growth specimens consisted only of casting, deforming, and recrystallizing prior to the grain growth anneal. Usually no attempt was made to homogenize samples with prolonged annealing. Experiments. To test the Whelan hypothesis, grain growth experiments were performed with samples in which the degree of solute segregation was altered by controlling the solidification rate of the alloys. The initial experiments were performed on the Pb-Ag system. Alloys containing 0.01 at. pct Ag were produced from 99.9999 pct Pb and 99.999 pct Ag. Cylindrical samples, 40 cm long and 12 mm in diam, were solidified in graphite-coated Vycor tubes by lowering them through a vertical furnace at varying rates with the furnace power settings constant. Six-centimeter sections were discarded from each end, and the 28-cm section from the center was cut into sections 25 mm long for grain growth experiments. These samples were deformed with the aid of a drophammer to a uniform thickness of 5.7 mm. After almost instantaneous recrystallization, the samples were given a grain growth anneal for various times at 260°C in a salt bath. Experimental results are shown

Jan 1, 1970

A. W. AMBROSE, Washington, D. C.-Did you make any analysis of the amount of emulsion at the well and after you flowed it through a lead line to the storage tank? E. A. TRAGER.-B. S. can be formed in passing through a lead line by the friction due to the roughness of the pipe and the irregularities at the joints. R. W. MOORE.-Did you find the percentage of water to be limited to the percentage of oil in the emulsion which formed? E. A. TRAGER.- Yes, the percentage is about 67 percent. water and 23, per cent. oil. R. W. MOORE.-If you added more water would the emulsion be permanent? E. A. TRAGER.-Yes, it would be permanent, but the excess water would separate out. THE CHAIRMAN. (C. W. WASHBURNE, New York, N. Y.).-Did you use hot or cold water in these experiments?

Jan 12, 1919

By A. H. Underwood, M. –Ls. Trépanier

INTRODUCTION The King and Beaver mines of Asbestos Corporation Limited (ACL) were joined in 1957 to form the King-Beaver mine. In 1964, ACL purchased the Johnson's Asbestos Company. The combined underground workings are a part of the King- Beaver mine. Asbestos ore is mined at the rate of 4080 metric tons per day (mtpd) to provide 15% of the company's daily requirement in the Thetford Mines area. Figure 1 shows the location of Thetford Mines. Two shafts service the underground. No. 3 shaft, 457 m deep, is used for personnel and material transportation, downcast ventilation, and ore hoisting. No. 4 shaft, 820 m to the south, is 389 m deep. It is used for material transportation and upcast ventilation. Figure 2 shows the relative locations of the shafts and the underground workings. The ore is mined by block caving. HISTORY The orebody outcropped at surface and was first mined as an open pit. Underground mining commenced when open pit mining became impractical. Shrinkage stoping, used initially, was unsatisfactory in the highly fractured ore. Sublevel stoping improved ore recovery and safety, but did not overcome the adverse effects of the un- stable rock. Observations of the rock failures indicated that block caving would be satisfactory. This was confirmed by careful investigation and testing. A method of block caving similar to that used at the Miami Copper Company was adopted. The first block commenced production in June 1933. BLOCK CAVING General A large block of ore is undercut above pre- pared drawpoints. The ore above the undercut caves by its own weight. Caving progresses up- ward as the caved ore is drawn. A large proportion of the rock breaks up in the caving action so that it will pass through the drawpoints. Oversize blocks are broken by drilling and blasting or mudcapping. Figure 3 shows the progressive stages of block caving. In the central part of the ore zone, the vertical dimension of a block is determined by the 132 metres between production levels. When isolated ore pockets are developed, the vertical dimensions of a block depend on the extension of the ore zone above the undercut. The minimum horizontal dimension of an under- cut determines the cavability of the overlying block. When necessary, caving is assisted by drilling long horizontal holes into the block above the undercut and blasting them. This procedure speeds up or restarts caving. It will not ensure complete caving of blocks having undercuts less than 30 m wide. Orebodies suitable for block caving are highly fractured and wide enough to cave freely without excessive dilution. Undercutting must

Jan 1, 1981

By Makoto Ohlsuka

The ternary Ni2MnGa intermetallic compound is an intelligent material which has both a ferromagnetic property and a shape memory effect (SME). The use of the shape memory alloy films for an actuator of micro-machines is very attractive because of its large recovery force. The purpose of the present study is to investigate the effects of fabrication conditions and to clarify the relationships between these properties and fabrication conditions of the Ni-Mn-Ga films. The Ni-Mn-Ga films with a thickness of nearly 5 um were deposited with a radio-frequency magnetron sputtering apparatus using a Ni50Mn25Ga25 or Ni52Mn24Ga24 target. They were heat-treated at various temperatures between 873 and 1273 K for homogenization and ordering and then cooled in a furnace. The composition of the films depended on the sputtering power. The as-deposited films were crystalline and had columnar grains. After the heat treatment the grains widened and the grain boundary became indistinct with the increasing heat treatment temperature. The martensitic transformation temperature of the heat-treated films increased with increasing nickel content. Furthermore the effect of plastic deformation and constraint aging on SME is also investigated. After plastic deformation, the two-way SME was shown through the martensitie transformation and its reversion, The intensity of X-ray diffraction peaks from stress-induced martensitie phase was found. The constraint-aged films also showed the two-way 3ME by thermal cycling.

Jan 1, 2003