Search Documents

RICHARD A. CONKLING (communication to the Secretary*).-Mr. Hager says that his results on the correlation of well logs in the north Cushing field are the opposite to those of the author. Can he, then, explain why the structural dip of the formations increases with depth, as Dr. Ohern, in his criticism, sets forth that it does, and as all who have worked in these fields will admit, if the shales thicken on the crest of the anticline, as he says they do? We are willing to agree with Dr. Ohern that there is some evidence of a slight unconformity below the Bartlesville sand and think that we can prove, from a specimen in our office, that .this unconformity comes at the base of the Bartlesville sand in the south Cushing pool. On the Ingalls dome, in the southeast corner of Township 19 North, Range 4 East, however, we get results the same as those given by the author on Cushing. The Ballard well in the center of the Northeast Quarter of Section 33 is just 10 ft. higher, structurally, according to tile, surface contour, than the Ringold well -in the center of the Southwest Quarter of Section 34. The dip in the Bartlesville sand, between these wells, is 40 ft. and the dip on the top of the Mississippi lime is 75 ft. This also might be accounted for, partly by the unconformity, but the author used the interval between the top of the Oswego lime, which is about 420 ft. above the Bartlesville sand, and the oil horizon found in the lime in the Ballard well-just mentioned above-to find the depth at which the same oil should be found in a well in Section 5, Township 22 North, Range 3 East, 25 miles North. Using this interval below the Oswego in the former well, we predicted within 2 ft. where they would find the oil in the latter well. Of course, we know that it was accidental that we missed it only by 2 ft., but if there were much of an unconformity in this interval it would be more of an accident if we came within 100 ft. of the depth. Since it can be proven from most of the structures in this section that the clip continues to increase downward, below the Bartlesville at least, to the Mississippi lime, it does not seem necessary to the author to try to prove otherwise that the depth at which the shales will tend to thicken on top of a fold, has not been reached above the

Jan 6, 1917

By B A. Wake, G G. Lowder, M J. White

The Tooloom gold field is located within the New England Fold Belt in the far northeast of New South Wales, approximately 130 km south southwest of Brisbane. Gold was first discovered at Tooloom in 1857. Within a few years up to 10 000 people were mining placer gold deposits in the Tooloom valley and a few tried their hand at mining hard rock occurrences as well. Mining of alluvial gold continued in a small way at Tooloom until very recently, but only in the last few years, since Malachite Resources acquired its interest at Tooloom (now 100 per cent), has the full potential of this large, reduced intrusion-related gold field been appreciated. By the mid 1870s, once the alluvials were largely worked out, most of the early miners had made the 270 km trek north to the newly discovered Gympie gold field and Tooloom slipped into obscurity. Such was this obscurity that the Tooloom gold field was not recorded on published Government geological maps until 2001, four years after Malachite became involved. The many hard rock prospects that Malachite has identified in recent years were largely or completely unknown. Tooloom is a good example of blinkered thinking when it comes to modern mineral exploration. The New England province in NSW has long been the æpoor relationÆ to the much better known and more highly favoured Lachlan Fold Belt in NSW. It has also suffered serious neglect compared with the Queensland part of the New England Fold Belt that hosts such major gold deposits as Mt Morgan (>7 Moz), Gympie (>3 Moz) and Cracow (>1 Moz). Tooloom is proof that prospective geology does not stop at state borders.

Jan 1, 2004

By Robert E. Gray

The vat leaching operation at the Yerington Mine was started in October, 1953. The original plant facilities consisted of primary and secondary crushing, eight leaching vats, precipitation launders, sulfuric acid plant and the necessary maintenance, warehouse and administrative facilities. By 1961, 35,000,000 tons of oxide ore had been removed from the mine exposing the underlying sulfide ore body. A 5,000 ton per day concentrator was constructed and put into operation to treat the sulfide ore in November, 1961. The original crushing plants were used for both oxide and sulfide ores. By adding a third crushing shift for six days per week, the treated ore was increased from 12,000 to 17,000 tons per day. To balance the oxide and sulfide ore reserves, the concentrator was expanded to 13,500 tons per day in 1967. Again, no additional crushing facilities were added. It was anticipated that the treatment rate of oxide ore would be reduced from 12,000 to 9,000 tons per day. Instead, the addition of two crushing shifts per week, and improved operating procedures, increased the treated ore to 26,500 tons per day, 13,000 tons to the vat leaching and 13,500 tons to the concentrator.

Jan 1, 1975

By S. Saklar, i. Bayraktar

The effect of the feed size distribution on the kinetic parameters in pyrite flotation was studied. The kinetic parameters of the particular sizes were determined as a function of whether other particle sizes were present. From the data, a relation between the pyrite flotation rate and the particle size distributions was obtained. It was shown that the flotation rate constant (k) is a function of the size modulus (dt) of the Gates-Gaudin-Schuhmann distribution, and its variation may be expressed as k = a • exp(b . d,) for either individual size fractions or composite feed. Parameters a and b are dependent on the particle size distribution of the feed. Specifically, parameter a increases linearly as the distribution becomes coarser. The above relationship was also tested under conditions in which the collector (KAX) dosage was varied from 130 to 278 g/t. It was shown that the established relation was not dependent on the collector dosage.

Jan 1, 2002

By Mark Osborne, Ray D. Peterson, C. Edward Eckert

"The theoretical melting energy requirement for a typical hypoeutectic aluminum-silicon alloy is approximately 520 BTU/lb. It has been demonstrated, however, that even a state of the art secondary processing-automated lost foam casting operation can exceed this value by at least an order of magnitude when the actual thermal energy input from melting to solidification is monitored. Metal transfer and holding operations constitutes over 65% of this expenditure. The authors present relative benchmark energy expenditure information by unit operation for an offsite melting/lost foam casting line with a daily throughput in excess of 100,000 lbs. Efficiency improvements through optimization of the current process, and anticipated energy values at the culmination of a U.S. Department of Energy sponsored project to develop, integrate and demonstrate an advanced melting, transportation, and dispensation system will be cited.IntroductionThe size of the U.S. aluminum remelt pool was approximated to be 14.21 billion kg (31.27 billion pounds) by a recent study?, with the engineered castings (foundry) sector accounting for 3.25 billion kg (7.16 billion pounds) or 23% of that total. This study considered overall process yield and all major contributors to scrap. The values cited, therefore, are more meaningful than simply tabulating annual pounds shipped by sector.The foundry sector consists of Sand Castings, PM Castings and Die Castings categories appearing in Figure 1. All other categories comprise the wrought alloy sector. Wrought alloy production enjoys an energetic benefit from both scale and a relatively continuous operation. Many foundry operations, however, operate in batch mode at less than design metal throughput with characteristically longer melt holding periods. Since any detention of molten metal beyond melting represents an overhead use of energy, melt holding (secondary) energy expenditures can appreciably inflate melting energy requirements in the foundry."

Jan 1, 2009

By Robert B. Fulton

Staurolite, an iron aluminum silicate mineral, is used industrially as the source of aluminum in portland cement manufacture in areas where the aluminum constituent is not economically available from shale or argillaceous limestone. It is also used as a high value- in-use sand blasting agent and as a premium grade foundry sand. It is produced by E. I. du Pont de Nemours & CO. as a coproduct in titanium mineral production in Florida where it was first recovered on a commercial scale in June 1952 from the Pleistocene sand deposit known as Trail Ridge. In the Trail Ridge deposit it comprises about 36 of the heavy minerals, the principal other heavy mineral constituents being ilmenite, leucoxene, rutile, zircon, kyanite, sillimanite, and tourmaline. Staurolite and the other silicate nonconductive heavy minerals are separated from the conductive titanium minerals on high-tension separators. The silicates are then separated from one another magnetically, the staurolite being relatively magnetic. In the total processing, 200 tons of raw sand yield 7 tons of heavy mineral concentrate from which about one ton of staurolite is recovered. Staurolite production is approximately 100,000 net tpy. No other commercial production of staurolite is known. This process yields staurolite concentrates of the characteristics given in [Table 1]. These concentrates are sold as three products with the size distribution of subrounded particles shown in Table 2. All three grades are used in sand-blasting for cleaning metal, for paint removal, and for cleaning buildings. Staurolite compares favorably with lower unit cost abrasives, such as boiler slags and mineral aggregates, in applications where the abrasive is used only one time and is not recovered. Because it is hard, fine, clean, and dense it can reduce blasting time, with less material reportedly being required

Jan 1, 1975

By William C. Cox, Ronald E. Heuer, Jean-Michel Loignon

The Gatineau shaft described in this paper was an excavation of about 38 m diameter and 21 m depth constructed in Gatineau, Quebec, across the Ottawa River just north of Ottawa, Ontario. A large sewage lift pumping station-was to be constructed in this excavation. Subcontractor for the shaft excavation and initial support was Beaver Underground Structures Ltd., of Dorval, Quebec. Mr. William C. Cox of Beaver conceived the idea for the support system used in this excavation, and was responsible for the construction activities. Initial analysis and design concepts for the lining system were developed by Mr. Ronald E. Heuer. Detailed lining design and construction monitoring were the responsibility of Mr. Jean-Michel Loignon. Geologic conditions indicated by two borings within the shaft area are illustrated in Fig. 1. The shaft excavation would be in the sensitive Leda silty clay. The clay is of stiff to very stiff consistency, with an insitu vane shear strength averaging about 115 KPa (2400 psf) and a reported low value of about 87 KPa (1820 psf). Low strength values were from the middle of the clay layer, with higher strengths at the top and bottom. Average shear strength at the level of the base of the excavation was about 137 KPa (2860 psf). Remolded vane shear strength averaged about 20 KPa (420 psf), with a reported low of 13 KPa (270 psf). Based upon average strength values, the clay sensitivity is 5.8. The clay has an average water content of 53% (range 43 to 66%), which is near its liquid limit (average 56%). The clay unit weight is about 1760 kg/m3 (110 pcf). Underlying the shaft site at shallow depth is limestone bedrock within which the piezometric head is approximately equal to the original ground surface elevation. For shaft support, a -cast-in-place concrete wafer system was considered, but was discarded because of time restrictions imposed by concrete placement and curing. The support system selected utilized liner plate with light steel walers closely spaced. The light rib

Jan 1, 1983

By J. M. Cormie

"The orebodies of the East Malarcic mine are interesting from a geological standpoint because of the very small amount of vein quartz, the occurrence of much of the ore in soft greenstone schist, the presence of innumerable bodies of porphyry and diorite, and their obvious relationship to structural features .The property lies in the northeast part of Fourniere township in western Quebec, and within the important fault zone that geological mapping in recent years has shown is traceable wesrward through the Noranda and Kirkland Lake camps and eastward to beyond the Val d'Or region . The claims included in the property were staked by J.P. Norrie and L. K. Coffin in 1932, but gold was not discovered until i934. Production began late in 1938. The total amount of ore milled up to the end of 1945 was 2,837,091 tons from which gold having the value of $16,631,758 was recovered.The region is underlain by an alternating series of Early Precambrian sediments and volcanics cut by innumerable intrusives. These are more fully described in the works of Gunning, Ambrose, and Norman. The East Malanie property is underlain by three formations, which, named from north· to south, are : the Cadillac sediments, the Blake River volcanics, and the Kewagama sediments. In addition, there are countless intrusions of porphyry and diorite, particularly in the greenstone, occurring in all sizes up to those measurable in hundreds and even thousands of feet . These constitute a large proportion of the greenstone in places. In many parts of the ore zone there is more porphyry and diorite than schist. The greenstone itself is not homogeneous but includes peridotite, andesitic lava, and soft talcose schist.Orebodies have been found in both the Blake River volcanics and the Kewagama sediments. They are not known to occur in the Cadillac group. The ore occurs in a zone of pyrite mineralization in which almost no other metallic minerals and very little vein quartz are present. Generally, the grade varies directly with the amount of pyrite. The mineralization is later than all the rocks of the area. Diorite was a particularly favourable rock for mineralization and contains the highest grade of ore, but any rock in the fault zone may be ore-bearing, whereas the same type away from the zone is not."

Jan 1, 1954

By Stephen A. Hare, O&apos

Powder metallurgy processing of commercial Raney nickel powders was examined. The typical angular particle shape, in conjuction with aluminum present in a eutectic phase, facilitated interlocking leading to excellent green strength after compaction. Density and porosity as influenced by the compacting pressure were studied over the range of 37.5 to 207 meganewton per square meter (MN/m2). Sintering in an inert atmosphere from 575° to 850° C caused a volume increase which is attributed to a solid state reaction between Al and Ni2Al3 phases. The reaction is 3Al + Ni2Al3 ? 2NiA13. A thermal pretreatment of 70 hours at 700° C was required to prevent this reaction from occurring during sintering. Density and porosity as a function of compacting pressure and sintering temperature were determined after a thermal pretreatment of the powder.

Jan 1, 1976

By R. A. Roberti

Most copper refineries use conventional wheel systems to cast anodes. over a period of time the copper moulds that are used become warped and cracks develop. To control mould warpage, the mould's are either rejected after a certain warpage is reached, or the shape is restored by mechanical means. The cracks, unless they are very severe, are repaired by a peening process. Even with regular maintenance to control warpage and cracks, the moulds have a limited useful life. If warpage and cracks are not controlled, anode quality deteriorates and tankhouse operations are seriously affected. -An intensive study was initiated to develop means of controlling mould warpage which culminated in the d?evelopment of technology to control mould warpage to within ±1. 5 mm, and at the same time effectively contr0l: cracking and significantly increase the mould life-. The warpage control has been achieved by using a unique mould design. Mould cavities are present on both sides of the mould and periodic inverting controls the wa-rpage in the cavities. The mould casting procedure has been developed and all production wheels have been converted to the new mould design. The performance characteristics of these moulds will be detailed. 21

Jan 1, 1987

By Falbo A, Barbaro M, Esposito MA, Passariello B

Acidic reductive leaching is one of the best known and most widely employed chemical processes for beneficiating minerals of industrial interest. Conventional acidic leaching with sodium dithionite (Na2S2O4), employed to bleach industrial minerals used in the production of ceramics, glassware, paper etc, does not always allow products of high quality to be obtained. In the work reported here two reducing agents, ascorbic acid and oxalic acid, have been employed in a medium acidified by means of sulphuric acid. Continuous systematic tests have been performed on a kaolin sample containing 0.8 per cent Fe2O3, adopting various operating parameters such as, leaching time, temperature and reagent concentration. In each case the total quantity of bi- and trivalent iron dissolved was ascertained. Removal of 80 per cent and 100 per cent of iron with ascorbic and oxalic acid respectively was obtained, while less than one per cent of iron was dissolved in the presence of sulphuric acid only. Products having a very good degree of whiteness (92 - 94 per cent) were obtained, whereas with sodium dithionite the degree of whiteness was in the 85 to 88 per cent range. The best conditions identified were applied to a sample of quartz for the removal of ferric impurities.

Jan 1, 1993

By S. Khan, M. Auret

Due to the modernisation of mines, traditional training methods may be supplemented to support the upskilling of supervisors in mines. A project was initiated by the SAMERDI SATCAP programme to demonstrate the “art of possibility” through a modern training methodology. Two exemplar digital supervisory leadership development modules for underground gold and platinum-group metal conventional and modernising mines, were developed for potential uptake by the mining industry. These exemplar modules were exhibited on a digital platform, towards leading and driving mining modernisation. The research adopted a mixed method approach that included a literature review, a review of an existing supervisory leadership development programme, data gathering, a pilot study, and stakeholder validation workshops. The research supported the development of exemplar digitised modules. The two digitised modules were showcased to the industry for potential adoption. Training slides, a facilitator guide, and a training video were developed for ease of use by industry. The training modules are generic and not specific to a particular mine. They may be used by multi-commodity mines, including gold and platinum-group metals, as ‘stand-alone’ modules. They are customisable, through consultation with relevant service providers for specific working environments. The findings indicated that both the traditional classroom training and the new digitised online learning solution offer advantages for supervisory leadership development. Digital learning is not a new concept for supervisors at mines and modern training methods are well-supported by supervisors in the industry. A ‘modernised’ training solution may consider a ‘blended’ learning approach that combines traditional training with digital methods.

Jun 27, 2025

By A. F. Baker

The Bureau of Mines conducted pressure-drop studies in a 4-foot-diameter simulated blast furnace shaft to compare anthracite metallurgical briquets with coke and formcoke. The test materials were used alone, layered, and in mixed burdens of commercial fuel-to-ore ratios. Anthracite briquets had a higher pressure drop per foot than furnace coke, but they had a lower pressure drop per foot than formcoke. This appears to be due to packing and shape, as well as to particle size. The superficial air velocities at which beds of briquets and furnace coke disrupted were about the same. However, if briquets of the shapes and sizes tested are substituted for furnace coke in commercial metallurgical furnaces, higher blowing pressures will be required to deliver comparable amounts of air. Test burdens with more than 5 percent material smaller than 1/4-inch diameter showed significant increases in resistance to airflow.

Jan 1, 1967

By R. W. Woodward, G. K. Burgess

minum bronze. Nearly all copper-base alloys are improved by rolling processes, but the copper-aluminum alloys seem to possess equally good properties when cast or rolled; this is a remarkable metallurgical fact. Another important property of these copper-aluminum alloys is their resistance to alternating stress. Many tests indicate that their resistance is greater in this respect than that of some steels, and I have seen instances when cast aluminum-bronze bolts have outlived five steel bolts in foundation work subject to severe shocks. I mention these various instances to indicate that work originally started as research for substitution of one material for another frequently develops 212 article which has properties not possessed by the original metal or alloy. I have dwelt particularly on the aluminum bronzes because recently I have done more special work on them than on other alloys, but I believe that the use of aluminum itself, in many combinations of metals, is a very important subject for investigation. Undoubtedly, after the war, the cost of aluminum will be reduced from its present price, and considering its low specific gravity it offers a very interesting and important field for research in the non-ferrous business. Naturally, if combinations containing aluminum can be developed in view of a probably increasing supply of metal, the cost will be reduced. This will benefit the industry generally and will immediately conserve tin. Bronzes, Bearing Metals, and Solders G. K. Burgess* and R. W. Woodward,† Washington, D. C.— From a metallurgical standpoint, there are several ways in which a reduction of the tin consumed in commercial non-ferrous and white-metal alloys can be effected. First, a reduction of the tin content of the alloy; second, substitution of part or all of the tin content by some other metal; third, a substitution of a different type of alloy, which in some cases also involves a change in mechanical design. The Bureau of Standards has been studying these methods of conservation for tin alloys, particularly in regard to babbitts and bearing metals, bronzes, and solders. Much of the information sewed by the Bureau was obtained from answers to questionnaires sent to manufacturers and users of these materials, so that, in general, any of the following suggestions or recommendations can be considered as being practical and as having already been thoroughly tried. Bearing Metals There is no question that the tin content of nearly all bearing metals can be reduced to some extent, and in some cases actually eliminated

Jan 1, 1919

By A. J. Boyer, T. R. Meadowcroft

An experimental determination has been made of the efject of surface diffusion on the vapor pressure obtained in a Kwudsen cell. The results show that a knife-edge orifice in a molybdenum lid may give erroneous results for the vapor pressure of silver. when a correction suggested by winterbottom and Hirth is made, the results become meaningful. Experimental work with cylindrical orifices in molyhdenz~m lids and knife-edge orifices in ceramic lids shows that good vapor-pressure results may he obtained when the orifice is designed so that ejfusion is the only significant source of weight loss. THE Knudsen effusion cell technique has been used by many investigators to study relative and absolute vapor pressures over metals and alloys at elevated temperatures. As a result of this interest, some theoretical studies have been made of geometric factors affecting effusion from the orifice of a Knudsen cell. A review of these studies has been made by Margrave.1 Recently, Winterbottom and Hirth2 have suggested that a physical effect, that of condensation, surface diffusion, and re-evaporation, may seriously affect Knudsen cell measurements, especially when a knife-edge orifice is used. Inasmuch as many of the present vapor-pressure data have been obtained using knife-edge orifices. it was felt that an experimental evaluation of the effect of surface diffusion on Knudsen cell measurements would be of value both in the design of the cell orifice and in establishing realistic estimates of the limits of error for existing data. The experimental program was in two sections. Firstly, measurements of the vapor pressure of silver were made in cells with cylindrical and conical orifices in which the surface-diffusion contribution to the weight loss should be negligible. These results were correlated with existing data to give a reliable measure of the real vapor pressure of silver. Secondly, measurements made using knife-edge orifices were corrected using the surface-diffusion theory of Winterbottom and Hirth2 and were then compared to the real values. The experimental arrangement is shown in Fig. 1. The balance was an Ainsworth RV-AU-1 automatic recording microbalance capable of measuring weight changes of ±0.02 mg on a total load of up to 100 g. The temperature was measured by an optical pyrometer signted on the bottom of the suspended crucible. The temperature readings were calibrated in a separate experiment in which pyrometer measurements were made while at the same time thermocouple readings were taken of the temperature at the inside top and bottom of the crucible. The range of reproducibility with this technique was ±4°C. A constant voltage source maintained a temperature of ±2°C at 1200°C over 10 hr. Silver of 99.99 pct purity was used in nonporous alumina crucibles. Lids of molybdenum, tantalum, or magnesia were cemented to the crucible using a sodium silicate cement. Table I shows the characteristics of the lids used. The vapor pressure is obtained using the basic Knudsen formula:

Jan 1, 1965

By G. J. Mei

Separation of hematite and iron-containing silicate gangue - aegirine by Flotation using fatty acid collector and (NH4)2SiF6 depressant was investigated in this paper. The flotation tests with single minerals show Ammonium hexafluorosilicate (AHFS) is a selective depressant for aegirine in hematite flotation in weakly acidic medium, which can strongly reduce the flotation recovery of aegirine in the pH range of 4~5 while has no evident effect on the flotation of hematite. The results of flotation tests with actual ores show the separation of hematite from aegirine gangue by forth flotation was possible, and good selectivity was achieved. Chemisorptions were observed on aegirine mineral surface treated by AHFS solution by using SEM and IR spectrum measurements. On the basis of coordination chemistry, a comprehensive mechanism, which reasonably explains the selective depression of AHFS for iron-containing silicate, is also proposed.

Jan 1, 2014

By Elsa Agante

Recycling of solid wastes, a common practice nowadays, requires the separation of the different materials in order to increase the products added value. The separation of one plastic from mixtures of different types of plastics is not easy due to their similar physical properties, but different techniques are available, from automatic sorting systems based on optical sensors to techniques adapted from mineral processing, namely gravity, froth flotation and electrostatic processes. In the last decade, many researchers have addressed the separation?s problem of different polymers, like Polyethylene Terephthalate (PET) and Polyvinyl Chloride (PVC), two polymers commonly used in packaging which have similar density. One proposed technique is the classical froth flotation performed in agitated cells. Froth flotation is a versatile and relatively cheap process widely used in mineral separation. It is based on the different behaviour of particles in the presence of an inter-phase air-water, which depends on the materials surfaces properties. Froth flotation can be affected by some variables such as impeller speed and air flow rate. Agitated cells, when used with low density materials, like plastics, can produce overstated turbulence that prevents the adhesion and collection of particles in the froths. In this case, separation is favoured by column flotation smoother hydrodynamics. This paper proposes the separation of PET from PVC by column flotation. The experimental work was carried out in a column of 9cm diameter and 1m high. The effects of some operating conditions, such as depressor and frother concentration, air flow rate and feed grain size on products grade and recovery were evaluated and the best flotation conditions for the separation of these plastics were established.

Jan 1, 2006

By E. J. Eisenach, Edward Matsen

AT the present time the Climax Molybdenum Co. is the largest molybdenum producer in the world and the operator of the largest underground mine in North America. It has grown steadily and rapidly since its beginning in 1917. Only 250,000 lb of MoS2 were produced during the first year from 1917 to 1918 when the company was formed. Operations were suspended shortly thereafter because of the lack of a market and knowledge of the uses of molybdenum. During World War I it was used as a substitute for some rare metals and for minor chemical purposes. After 5 years of intensive research and sales promotion, Climax metallurgists succeeded in finding proper applications for the newly discovered metal and the mine was reopened in 1924. Demand for molybdenum increased gradually and in 1930, 3.5 million lb of MoS2 were produced. In the meantime, research work for additional uses of molybdenum continued until it had established itself as one of the most important alloying elements in producing high quality steels. After the start of World War 11, from January 1942 to October 1953, 43 million tons of molybdenum ore were mined and 484 million lb of MoS2 were produced. Climax mine is located in Colorado, 100 miles southwest of Denver and 12 miles northeast of Leadville on the Continental Divide of the Rocky Mountains. The principal mine workings range from 11,170 to 12,000 ft in elevation. Topographically, it lies in the base of a large cirque that is surrounded by Mt. Bartlett to the north, Clinton Peak and McNamee Peak to the east and Ceresco Ridge to the south. This cirque opens to the west and to the Ten Mile Valley.

Jan 3, 1954

By P Stewart, S Cowie, A Offer, J Carpenter, E Jones

The Ban Houayxai Gold-Silver Operation is a producing asset for Australian-based copper and gold producer, PanAust Limited. The Operation lies within PanAust’s 2600 square-kilometre Phu Bia Contract Area in northern Laos. Commencing production in 2012, Ban Houayxai is operated by PanAust’s Lao-registered company, Phu Bia Mining. PanAust owns a 90 per cent interest in Phu Bia Mining. The Government of Laos owns the remaining 10 per cent. The Operation mines an intermediate sulphidation epithermal gold-silver deposit and comprises an open-pit feeding ore to a conventional carbon-in-leach process plant. Metallurgical recoveries for gold and silver are approximately 75-85 per cent and 55 per cent respectively. To year-end 2017, the Operation had poured 0.65 million ounces (oz) of gold and 4.7 million oz of silver. The Ban Houayxai Ore Reserve supports a mine life of approximately four years from the end of 2017. The Ban Houayxai deposit is in an early Permian volcano-sedimentary unit which is part of a late Carboniferous to early Permian (310–270 million years ago) volcanic-plutonic sequence of the Truong Son Fold Belt. The deposit formed when hot saline (240–415°C, 2.7–13.0 weight per cent NaCl equivalent) fluids ascended from a geologically fertile island arc porphyry into overlying volcanics along a fault or faults in the early Permian (290–256 million years ago) (Manaka et al, 2014). CITATION: Carpenter, J, Cowie, S, Stewart, P, Jones E, and Offer, A, 2018. Machine learning at a gold-silver mine: a case study from the Ban Houayxai Gold-Silver Operation, in Proceedings Complex Orebodies Conference 2018, pp 82–85 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

Bosworth, T. 0. The Mackenzie oilfield of northern Canada. Petroleum Times, vol. 5, Apr. 30, 1921, pp. 489-491. Jour. Inst. Petroleum Technologists, vol. 7, Oct., 1921, pp. 276-290; discussion, pp. 290-297. Gives location of the field, some of its geology, mode of occurrence and character of the oil. See also Oil Trade Jour., vol. 12, June, 1921, pp. 48-108. Canadian Min. Jour., vol. 42, May 27, 1921, pp. 420-422. Oil and Gas Jour., vol. 20, June 3, 1921, pp. 90-90. Petroleum World (London), vol. 18, June, 1921, pp. 233-2.64, 236-238, 240-241. Bull. Canadian Inst. min. and met., July, 1921, pp. 629-638. Mining and Metallurgy, Oct., 1921, pp. 47-48. Bureau of Foreign and Domestic Commerce. Resources of Balkan and Near Eastern countries. Commerce Repts., Oct. 24, 1921, pp. 488-489. Includes summary of the mineral resources of these countries, mentioning petroleum and allied substances in Roumania, Albania, Anatolia, Mesopotamia, Palestine, Arabia, Persia.

Jan 1, 1921