Search Documents

By Peretti, E. A.

Since its development about forty years ago by J. V. N. Dorr (Cyanidation and Concentration of Gold and Silver Ores, McGraw Hill Book Co., 1936, 1-5), and others, continuous countercurrent decantation has not only become one of the standard methods for extracting gold and silver from their ores, but has also found wide application in other metallurgical and chemical industries. In 1917 L. B. Eames published an excellent paper (Countercurrent Decantation, Trans AIME, 1917, 57, 143- 158), in which he determined the effects of grade of ore, ratio of solution precipitated to ore treated, variations in the density of the thickener spigot discharge and variations in the value of the barren solution upon the gold assay of the solutions discharged from the thickeners in the system. Eames showed that, other things being equal, the dissolved gold lost in the tailing varies directly as the value of the ore and as the value of the barren solution. The tailing loss de- creases rapidly as the ratio of solution precipitated to ore treated is increased to about three or four to one. Beyond this point the improvement is negligible.

Jan 1, 1949

By D Larson, M Finger

Chemical explosives may become a key element in many of the in situ energy and mineral recovery methods under development. This paper discusses the potential role of explosives in deep rock mining for resource recovery. Several energy and mineral recovery programs described are an outgrowth of the Plowshare Program and Explosives R&D conducted as part of the AEC/ERDA mission at Lawrence Livermore Laboratory. Several important aspects of the use of explosives in deep rock mining are reviewed. First, the status of knowledge of deep rock fracturing to create permeability underground is discussed. Completely contained blasting has not been a widely applied tool used in the mining industry. We conclude that data available on deep rock fracture is minimal and that the mechanisms that control the processes must be understood before technical and economic feasibility can be established. We also discuss the unusual problems in the selection of an explosive or blasting agent for deep rock applications including emphasis on the functioning at depth and safety aspects. Finally, a brief review of similar activities within the U.S. is given.

Jan 1, 1976

By Alan J. Wianwright

Introduction ??New world-class Upper Devonian porphyry Cu-Au system located in south Mongolia ??6.5 km NNE-trending mineralized corridor ? 4 discrete deposits ??Southern Oyu deposits: Chalcopyrite, deposits: bornite ??Hugo Dummett: Zone: Hypogene chalcocite in addition to chalcopyrite and bornite ??Total resource exceeds ~2 Gt@ >1% Cu, >0.25 g/t Au (0.6% Cu equivalent cut-off) (Ivanhoe Mines press release, 2005)

May 1, 2006

By O. G. Motlogelwa

Any company operating a fleet of trucks will be greatly advantaged if the associated fuel costs can be decreased. The optimal tonnage that trucks should be hauling to ensure minimum consumption of diesel fuel has been investigated. The fuel consumption in litres per ton for a fleet of trucks hauling different tonnages of iron ore was recorded in a time-motion study and the optimal tonnage was determined. The following points emerged as a result of the research: > The diesel fuel consumption in litres per ton decreased with increasing tonnage, which means that in order to improve fuel efficiency, the trucks should carry 21 t > As a result of queuing, Africa Truck Hire (one of the two equipment contractors) loses R282.57 per day to diesel that the trucks burn when they are left idling. It is thus advisable that the company adopt a policy of requiring the drivers to switch their engines off while queuing at the stockpile > Filling up the trucks during each shift or rationing the quantity of diesel to 200 litres each shift has a negligible impact on the trucks' fuel efficiency > For the company to spend 35% of their revenue on fuel, the diesel price would have to be between R8.14 and R8.78 per litre.

Jan 1, 2013

By JOE SIERAKOSKI, W. R. Hardwick

This paper , which describes mining methods and practices at the Johnson Camp copper -zinc mine , Coronado Copper & Zinc Co. , Cochise County , Ariz . , is one of a series being prepared by the Bureau of Mines on mining methods , practices , and costs in various mining districts of the United States . Johnson Camp is in the eastern foothills of the Little Dragoon Mountains in secs . 23 , 24 , 25 , and 26 , T. 15 S. , R. 22 E. ( fig . 1 ) . The mining property is in the low, rolling foothills at an altitude of slightly over 5,000 feet above sea level ( fig . 2 ) . The area is covered with scattered grass and small desert shrubs . The climate is mild , with hot summers and mild winters . The average annual precipitation is about 12 inches . The nearest surface water is the San Pedro River , some 12 miles west of the mine . The property is owned by the Coronado Copper & Zinc Co. , Los Angeles , Calif . This report gives a brief history of the property , describes the general geology of the area and of the ore deposits , outlines the methods of prospecting and exploration , and gives the methods of sampling and of estimating ore reserves . Development and stoping methods are explained . Underground transportation , ventilation , mine drainage , and safety measures also are described . The last section gives a brief description of the milling practice .

Jun 1, 1957

By Raymond E. Davis

LET'S imagine we are at the Grand L Coulee Dam, where daily 15,000 barrels of low-heat Portland cement and 27,000 tons of processed aggregate in various sizes are mixed to produce 30,000 tons of concrete. Inspect the autographic records which show for each 4-cu-yd. mixer batch of concrete the weights of its constituent materials including its several sizes of aggregate, cement, and water, and which also show the period of mixing and the consistency of the mix. Watch the inspectors sample and test the aggregate for gradation and moisture content of sand, and sample the concrete for homogeneity. Watch the huge buckets deposit the concrete in the forms. It looks too dry to handle, but the concrete vibrators make it melt away. Just enough vibration fully to com- pact the mass, but not enough to produce segregation of the materials; the inspector says when. See the sprinkler system covering all hardening concrete with a spray so that it may not thirst for water. Watch the cleaning of the top of an old lift preparatory to placing a new lift; the sand blasting; the blow-down; the mop-up; the minute inspection.

Jan 1, 1939

By R. E. Robbins, H. R. Brager

THIS note describes an unusual result obtained in an electron microscope investigation of cavities produced in commercial type 304 stainless steel irradiated in a thermal reactor (ETR) at 290°C to a high neutron flu-ence, 6 x loz1 n per sq cm. The analysis of the steel used is given in Table I. The unusual result is that the calculated quantity of helium gas produced by transmutation during the irradiation, 12 ppm, is less than one-tenth the amount of gas necessary to balance the surface tension of the observed cavities produced in the steel during ETR irradiation. Therefore, the cavities would be expected to behave like voids; however, they behave like "gas filled" bubbles. The maximum quantity of helium produced in the steel by B" transmutation was 8 ppm. In addition, the amount of helium formed by (n, (1) fast neutron reactions with the major alloy constituents and nitrogen was calculated to be 4 ppm based on the tabulated differential or effective fission-averaged cross sections of elements in type 304 stainless steel irradiated in typical thermal reactors.', In previous investigations concerning commercial austenitic stainless steel irradiated in a thermal reactor, the amount of helium gas calculated to be produced by transmutation has always been significantly greater than the amount calculated on the basis that the bubbles were gas filled, PPs= 2y/R. The balance of the gas was assumed to be in bubbles smaller than could be detected on the electron micrographs. Accordingly, the bubbles were attributed to helium produced from transmutation of impurity boron by thermal neutrons. These bubbles were not uniformly dispersed in the matrix but were located principally at grain boundaries, or were radially positioned around a few precipitates located in the matrix and at the grain bundaries., 4 Voids have also been observed in austenitic stainless steel irradiated at high temperature to high neutron fluences in the EBR-I1 and Dounreay Fast Reactors. The voids were uniformly distributed throughout the matrix. The amounts of helium gas produced by transmutation during these irradiations were less than one-tenth the amounts needed to balance the surface tension of the voids formed by the fast reactor irradiation. The fast reactor results are quite analogous to those reported here for the ETR irradiated steel. Electron microscope examination of the fast reactor irradiated material after a 1 hr postirradiation annealing at 900°C disclosed that essentially all the voids had been eliminated. The authors stated that the voids had developed due to the high concentration of vacancies produced during irradiatin., 6, ' The microstructure of the ETR irradiated material as-tested at 75O°C, Fig. 1, contained about 2 X lot5 cavities per cm3 with an average diameter of 110A. With the Van der Waals b correction and y = 1500 ergs per cm2, 300 ppm He would balance the surface tension of the observed cavities. Stereoscopic examination of the electron micrographs showed that the cavities were neither preferentially located near the grain boundaries nor highly concentrated at specific regions or precipitates. The cavities were nearly uniformly distributed throughout the matrix, on dislocations and at grain boundaries. These observations imply that the cavities were not the sole results of B'O

Jan 1, 1969

By R Strand, L Reading, G Keir

A major challenge in managing coal seam gas (CSG) water is predicting how much water will be produced as the industry develops. Klohn Crippen Berger Ltd (KCB) was commissioned by the Queensland Department of Natural Resources and Mines (DNRM) to develop a tool to forecast where, when and how much CSG water will be produced in the Surat and Southern Bowen Basins under various industry expansion scenarios.The water production tool (WPT) uses the Theis equation, a non-equilibrium groundwater flow equation that accounts for the effect of pumping time on well yield in confined aquifers, to predict water production volumes. Where multiple pumping wells are in close proximity, the required pumping rates for coal seam depressurisation are reduced. Therefore, pumping effects are projected spatially to assess interference effects between wells. Water production is then upscaled to the projected scale of the CSG industry within the Surat and Southern Bowen Basins.Two modifications were made to address the dual phase nature of CSG extraction (a transmissivity reduction factor) and the impact of weathering at the eastern margin of the Surat Basin (a ænear edge effectÆ factor). These factors modify relevant hydrogeological parameters in a consistent and defensible manner to more closely match observed water production.The WPT was verified by comparing results to equivalent Theis equation calculations and to type curves provided by CSG proponents. Calibration was achieved by varying the spatial distribution and intensity of the near edge effect factor in conjunction with a chi-squared analysis of residuals.The tool, which is now being maintained and further developed by the Centre for Water in the Minerals Industry (CWiMI), was built to balance numerical complexity against relative flexibility and simulation speed. The result is a tool that can produce statistically relevant results of prescribed scenarios to plan water handling and treatment requirements in discrete zones of operation.CITATION:Strand, R, Reading, L and Keir, G, 2013. Water production simulation tool for coal seam gas operations in Bowen and Surat basins, in Proceedings Water in Mining 2013 , pp 311-320 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

Following the suggestion of Engineering Council and at the direction of, the President, representatives from each of the Federal Government bureaus interested in map-making were called into a conference for the purpose of coordinating all of the Government's map-making activities. This conference has now reported back to the President the results of its findings, which indicate that Engineering Council's recommendation in this matter was well founded. While the conference report states that its members were of the opinion that little duplication of effort existed, it recommends the formation of a permanent Board of Surveys and Maps. An extended review of the map-making activities, which is given as an appendix to the report, indicates that this recommendation is a logical step. The conference recommendations concerning this Board of Surveys and Maps are as follows: (1) the Board is to he com-posed of representatives of mapping bureaus to be assisted by outside engineering organizations, which have been named above; (2) the estab-lishment of an information office in one of the Government bureaus, preferably the Geological Survey, which is to be under the supervision of the Board and is to be a mapping information clearing house for the Government and outside engineering organizations; (3) copyright laws are to be so changed that copies of all. maps made in the United States and with Governmental authority, will go to the central information office; (4) the Government departments are to receive orders to cooperate, with the Board; (5) future topographic maps of all kinds are to conform with specifications for the standard topographic map; (6) the U. S. Coast and Geodetic Survey to have supervision of final adjustment of all important control data under specifications approved by Board of Surveys and Maps; (7) surveys in the form of maps and publications are to be issued as soon as possible after field work has been completed; (8) program of the Interdepartmental Committee on Aerial Surveying was approved. Outside technical and scientific organizations that are called in for consultation are to operate in an advisory capacity only, responsibility for action on Governmental work is. to rest solely with the Governmental agencies.

Jan 12, 1919

By M. Cossette, V. H. Tran

"How can the durability of asphalt pavement be doubled without increasing highway budgets? Asphalt containing asbestos can provide the desired performance with additional costs being made up by longer life. The addition of a low percentage of asbestos to an asphalt mix permits a higher asphalt content without any consequent loss in stability. It is mainly the higher asphalt content that provides improved performance and durability, although the fibrous reinforcement plays a key role in preventing the propagation of micro-fissures. As well, several international studies show that, thanks to the latest production techniques, no environmental hazards need be incurred.RésuméComment doubler la durée des chaussées d'asphalte sans augmenter les budgets de voirie? L’asphalte contenant de l'amiante peut offrir les performances souhaitées et l'augmentation des couts initiaux peut être rapidement compensée par une durée prolongée. L’addition d'une faible teneur en amiante courte il l'enrobe de bitume permet des teneurs en bitume plus élevées sans subir une perte de stabilité en conséquence. C'est principalement la teneur accrue en bitume qui assure un améliorations propriétés physiques et une augmentation des performances mécaniques, ainsi qu'on prolongement de la durée. Cependant, le renforcement fibreux joue un rôle clef en prévenant la propagation éventuelles micro-fissures. Les nouvelles techniques évitent tous risques environnementaux"

Jan 1, 1991

By C. M. Liu

"The Freeport-McMoRan Sierrita Crystal Plant produces Copper (II) Sulfate Pentahydrate (CuSO4·5H2O) through a series of cooling crystallizers. In this process, high supersaturation and unwanted spontaneous nucleation promote fine crystals. Seeding through recycled crystal classification can manipulate the crystal size distribution (CSD) for larger crystals. Proper selection of the crystallizer for seeding can prevent spontaneous nucleation and promote final crystal size. This study shows when seeding temperature is closer to the crystallizer temperature, suspension densities in the crystallizers are promoted and overall CSD shifts to a larger size of crystals. INTRODUCTION Figure 1 shows an overview of the crystallization process. The in-plant feed flow, called Pregnant Mother Liquor (PML), enters the first crystallizer and is subsequently cooled through a series of four crystallizers. Specific temperatures are targeted for each crystallizer to ensure the crystallization process is operating within the metastable zone (MSZ). The discharged flow from crystallizer #5 then enters two cyclones. The overflow from the cyclones contains smaller crystals providing seed crystals for crystallizer #5. The underflow from the cyclones begins the drying process. The overflow from crystallizer #5 enters cyclone #3 for removal of fine crystals and seeding purposes. The underflow from cyclone #3 has the capability to provide seed crystals for crystallizer #1 or crystallizer #2. The overflow leaves the system as Spent Mother Liquor (SML). Undersize crystals dissolve into the PML and return back to crystallizer #1.THEORIES AND METALLURGICAL TESTS Seeding requires an understanding of the crystal size, solution temperature and amount of crystals that enter the crystallizers (1). For the seed crystal size, classified crystal seeds can prevent fine crystals returning back into the system which eventually leads to excessive agglomeration (2). Proper selection of the crystallizer can ensure seeding at an appropriate temperature. Seeding at a temperature much lower or higher than the saturation temperature promotes spontaneous nucleation. Typically, seeding between 4-5°F below the saturation temperature is acceptable (5). A general rule of thumb is to add the seed crystals at the temperature between the solubility curve and the metastable zone. An experiment conducted by Mettler-Toledo AutoChem, Inc. indicates seeding close to the solubility curve rather than the metastable zone promotes a lower supersaturation and nucleation rate but yields a higher growth rate and a greater number of larger crystals (1). The amount of seed crystals can not only change the suspension density but also narrows the width of the MSZ in the crystallizers. An experiment conducted by Jaroslav Nyvlt reports with the crystals absent, the maximum allowable undercooling is 6.3 degrees at a cooling rate, 5°C/hour. With the presence of crystals, it narrows the MSZ width to 2.2 degrees (4). Industrial crystallizers normally operate at suspension densities between 15% and 25% by mass. When suspension densities are lower than 15%, it increases the risk of primary nucleation and the probability of incrustations; on the other hand, if the suspension densities are greater than 25%, it can cause a greater attrition rate and increase the probability of deposits (6). Moreover, operating suspension densities between 15% and 25% are also sufficient to minimize supersaturation rate which promotes crystal growth over nucleation (2, 6)."

Jan 1, 2015

By Kumar P. Dharmasena, Haydn N. G. Wadley, Bill W. Choi

"Non-contact eddy current sensing methods have been developed and applied to Cd0.955Zn0.045Te crystal growth to obtain a better understanding of the melt, solid nucleation, and the growth process. The application of this sensor approach relies on a large difference in liquid and solid electrical conductivities near the melting point and requires knowledge of the relationships between the electrical conductivity, melt composition, and temperature. Using a multifrequency encircling eddy current sensor, the electrical conductivities of three different Cd1-xZnxTe (x=0.00, 0.045, and 0.08) alloys were measured as a function of temperature in a laboratory-scale vertical Bridgman furnace. The measured solid and liquid electrical conductivities were then used in electromagnetic finite element models to analyze the multifrequency responses of eddy current sensor designs during the simulated growth of a crystal. These eddy current sensors were fabricated and installed in a vertical Bridgman furnace and used to monitor many Cd0.955Zn0.045 Te growth runs. One sensor was placed in the vicinity of the ampoule tip to detect undercooling/spontaneous nucleation and two other sensors (""absolute"" and ""differential"" designs) placed to monitor the movement/curvature of the liquid-solid interface during crystal growth. The sensor data was used to characterize the initial melt state, detect the onset of nucle-ation, determine the growth velocity, and identify the shape of the interface.IntroductionSingle crystal CdTe and its solid solution Cd1-xZnxTe alloys (0.03<x<0.05) are used as infrared transparent substrates for infrared focal plane array (IRFPA) detectors [1-6] and as solid state y- ray detectors [7-9j. Cd1-xZnxTe substrates are normally ""mined"" from large polycrystalline boules grown by the unseeded directional solidification of Cd1-xZnxTe melts using either a vertical or horizontal Bridgman process [10-14]. The vertical Bridgman method is particularly popular for growing CdTe and its related compounds. In this process, a Cd1-xZnxTe ingot is produced by first melting a charge in the hot zone of the furnace and then vertically translating the furnace (with its associated axial temperature profile) relative to the stationary crucible to cause directional solidification. In spite of many experimental efforts to investigate the relationships between material purity, stoichiometry, the controllable growth parameters (furnace temperature profiles, ampoule geometries/materials, furnace translation rates and starting position) and the resulting material characteristics (grain structure, dislocation densities, IR transmission, macro-segregation etc.), the yield of Cd1-xZnxTe of a quality suitable for large area (e.g. 4 cm x 6 cm) substrates remains low (<10%). Since much of this poor yield is directly associated with the crystal growth process (e.g. melt stoichiometry, solidification velocity, interface shape, temperature gradients, cooling rate, etc.) intensive efforts are under way to improve this technology."

Jan 1, 1997

By L. Prosser, A. Iannacchione, G. Esterhuizen

The potential for roof falls in underground mines remains a clear and present danger for mine workers. An investigation of ground conditions in nearly 50% of the nation’s underground stone mines found that the state of roof stability is primarily determined in a limited and subjective manner. These large opening mines, with roof heights typically of 7 m or more, make physical observation difficult. Although some mines use monitoring techniques to gain additional information on roof stability, this practice is usually short-term and localized to address ground conditions in a particular section or part of the mine. A methodology to assess the risk for a roof fall is proposed in a preliminary fashion based on engineering judgment acquired from extensive underground stone mine experience and examination of related literature. The proposed method utilizes an observational technique to identify the risk of roof falls in three categories. Case study scenarios provide a realistic picture of model implementation. Providing the mine level decision maker with an accurate assessment tool to ascertain the level of risk related to ground conditions is expected to reduce mine worker injuries and fatalities. Moreover, the presences of danger can be overcome with a clear picture of quantified ground conditions.

By Gerald T. Homce

Accidental contact of overhead electrical power lines by mobile equipment is a leading cause of occupational fatalities in the United States, accounting for 20% of on-the-job electrocutions. Overhead electrical power line proximity warning devices (PWDs) are intended to warn personnel if mobile equipment moves within some preselected minimum distance of an energized overhead electrical power line. Two commercially available PWDs were tested at the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). The objective of the tests was to document performance capabilities and limitations for these PWDs by identifying factors that can influence their operation. The two PWDs evaluated in this research are the SIGALARM Model 210 marketed by Allied Safety Systems, LLC, and the ASE Model 2100 from Allied Safety Engineering. Both of these devices operate by measuring the electric field present around energized power lines. The PWDs were installed on a government-owned 22-st (20-mt) rough terrain crane. A purpose-built test site used for this research at PRL allowed operation of the crane near a variety of power line configurations operating at up to 25 kV. Most of the tests involved positioning the crane adjacent to one or more overhead power lines, adjusting sensitivities of the PWDs to alarm when the crane boom was approximately 20 ft (6.1 m) from the power lines, swinging the crane boom toward the lines under a wide variety of test conditions, and finally, for each unique set of test conditions, documenting the deviation from 20 ft (6.1 m) for actual alarm activation. Test results show that several factors can adversely affect PWD performance. PWD alarm accuracy generally deteriorated when operating with a boom position significantly different than that used for the device?s last sensitivity adjustment. Another factor that can affect PWD performance is configuration of the overhead power line(s) involved. Accuracy of alarm activa­tion distances was best for simple single-circuit installations, but degraded for multiple circuits on the same poles. This degradation was slightly greater for installations with different voltage levels and/or a combination of vertical and horizontal conductor arrangements. Performance also degraded for crane operation between two intersecting power line installations, especially for intersecting lines at different voltages. An additional aspect of power line configuration shown to influence PWD accuracy was phase sequence on the power line circuit(s). Specific phase con­ductor arrangements and combinations, particularly in multiple circuit installations, resulted in either improved or degraded accuracy.

Jan 1, 2008

By AIME AIME

AT A meeting of the Boston Local Section of the Institute, on Oct. 3, approval was voted to the work done by its representatives on the Committee opposing the passage of a bill by the, Massachusetts Legislature to license engineers. The report is as follows: The Joint Committee on Licensing of Engineers, which included a Committee of the Boston Society of Civil Engineers and representatives of seven other societies,* submitted to the members of the respective societies, on Jan. 8, 1921, a report in which it was stated that on Jan. 4, 1921, a petition was filed in the Legislature of Massachusetts by the Boston Chapter of the American Association of Engineers accompanied by a bill to provide for the registration of professional engineers and land surveyors. This report also stated that at a meeting of this committee, held on Jan. 7, 1921, it was voted:

Jan 1, 1921

By Jacob Bummer, Greg Roset, Dayle Flynn

"IntroductionStillwater Mining Company operates a Precious Metals Smelter (PMS) located in Columbus, Montana USA. The PMS processes iron, copper, and nickel sulfide bearing concentrates containing platinum, palladium, gold, and rhodium. The concentrates are produced from two mines in the Beartooth Mountains located in south central Montana. The PMS utilizes a 7.5 megawatt 3-in line electric furnace to smelt the concentrates, and two Top Blown Rotary Converters (TBRC's) to remove iron. In addition to the mine concentrates, the PMS also processes various forms of Platinum Group Metal (PGM) bearing recycled catalyst. The sulfide matte produced within the electric furnace and TBRC's acts as a collector for the PGMs. Throughout the operation of the PMS, there are three different forms of molten material that are processed through the Stillwater Granulation system: TBRC matte, TBRC slag, and electric furnace matte. This paper describes the operation of this granulation system.Tapping the FurnaceWhen a sufficient level of molten PGM bearing matte has been reached within the inner volume of the electric furnace, the molten material is ""Tapped"". Tapping requires drilling into the electric furnace until reaching the molten matte phase. The matte phase will drain out of the drilled hole through a graphite launder into a 5 ton refractory lined ladle. Once the ladle is full, the tap is plugged with a mud gun."

Jan 1, 2012

By Drury SA, Williams RD, Nind DC

The Airborne Thematic Mapper is an eleven channel digital scanner which acquires image data in the visible, near infra-red, short wave infra-red and thermal infra-red wave- lengths. A description of the system is presented which includes details of the operating wavelengths and performance parameters of the scanner. Consideration is also given to the aircraft installation requirements. During January 1984 the scanner surveyed the mineral rich areas of Leonora, Laverton and Kalgoorlie in Western Australia. This is a region of intense exploration activity for gold and base metals. Some 30,000 square kilometres were systematically surveyed in a period of ten days. This scanner was flown at 7,000 metres altitude giving a ground pixel size of 17.5 by 17.5 metres. The flight line spacing was 8 kilometres. The overall project took some thirty days from conception to completion. The planning and execution of this operation are described in detail. The resulting magnetic tapes provided 11 channels of digital image data over a 30,000 square kilometre area and a variety of image processing techniques were employed in order to capitalise fully on the results. The imagery provides a powerful tool for the geological mapping of the terrain. The data can also be used to monitor the environmental effects of mining operations.

Jan 1, 1986

By J. V. N. Dorr

DEADWOOD and the Black Hills were familiar names to me from childhood, for. I had an uncle who was among the earliest eastern investors there and I used to hear of the Uncle Sam mine and its rich ore back in the eighties. The spring of my junior year at college, in 1893, brought me an offer of summer work at the Deadwood & Delaware smelter, in Deadwood, and full of the thrill of the long journey from New Jersey, I went out as chemist and stayed four months. Within a week or two of my arrival, I went through the tragic experience of seeing an associate drink cyanide by mistake and die within a few moments. I shall never forget the horror of feeling that my lack of knowledge of an antidote might be responsible for his death, but I found later that the solution he drank was so strong that nothing could have been done. A year after graduation, when I had settled down to chemical research work in New York, an offer came to go back to the smelter in Deadwood, and within a few days I was again tramping down "the Gulch" with my lunch bucket and putting in the standard assay office shift of that day, from 7 a.m. to 6 p.m., with a half-day off on Sundays. During my absence East, the D. & D. smelter had been changed from a pyritic smelter, using native pyrite, and Homestake concentrate to matte the siliceous gold ores, into a copper-matting smelter using copper ores brought from Butte, over the newly-completed Burlington rail-road. The work was interesting, and the laboratory offered many opportunities for making improvements. I remember also undertaking experiments at home on a new method of gold precipitation for the chlorination process and leasing a mine in Strawberry Gulch that promised great things, but soon petered out.

Jan 8, 1927

By M. C. Ruiz

The leaching behavior of chalcopyrite concentrate in acidic CuC12-NaCI-O2 solutions was investigated. Experiments were conducted under continuos flow of oxygen at atmospheric pressures. The results indicated that among the variables temperature has the largest influence on the dissolution of chalcopyrite in this medium, and high copper extraction can only be obtained at temperatures near the boiling point of the solution. It was also found that the stirring speed did not influence appreciably the dissolution of chalcopyrite. An increase in the oxygen flow rate up to 0.1 1/min increased the copper extraction. The total chloride concentration affects the dissolution of chalcopyrite up to about 4 M. Copper extraction of 93 % was obtained in leaching chalcopyrite of size fraction -400 # Tyler at 105 OC in 2 hours.

Jan 1, 1997

By G R. Ballantyne, B Putland, I Lovatt, M Di Trento

The Tropicana Gold Mine, owned by AngloGold Ashanti Australia Ltd (70% owned and managed) and Independence Group NL (30%) is located 330 kilometres east-northeast of Kalgoorlie, Australia, in the newly developed Albany-Fraser Orogen. Following extensive feasibility studies, a high pressure grinding roll (HPGR)-ball milling circuit was selected based on the reduced power requirements and thus reduced operating expenses. The HPGR-ball mill circuit was estimated to require 75% of the energy of a standard semi-autogenous grinding (SAG) mill circuit. Even with an anticipated greater capital cost, the HPGR-ball mill circuit was found to give significantly better financial returns in all cases investigated in the feasibility study. A comparison between the specific energy requirements of the HPGR, crush and SAG based circuits (SABC) from the feasibility work was conducted and the HPGR circuit was found to be considerably more energy efficient. A survey was conducted and the efficiency of the HPGR was similar to both the overall circuit design and the HPGR laboratory results, reflecting the accuracy that is possible for design and operation of HPGR circuits.Between 2015 to 2016, the Tropicana circuit has achieved a 20% increase in throughput from 780 to 930 t/h, and this increase has been maintained in 2017. This improvement can largely be attributed to upgrades to material handling processes, increased HPGR speed and smaller HPGR screen apertures. The result of these changes has been to increase the ball mill capacity by increasing the breakage conducted by the HPGR.CITATION:Ballantyne, G R, Di Trento, M, Lovatt, I and Putland, B, 2017. Recent improvements in the milling circuit at Tropicana mine, in Proceedings MetPlant 2017, pp 73–83 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017