Search Documents

By L. H. Johnson

"INTRODUCTION The Pennsylvania anthracite industry produced 53 million net tons of anthracite during 1945. Fifty-one million tons was prepared for the commercial market (3), 3/ and 2 million tons (consisting of fine sizes) was used for colliery power consumption. Of the number of tons prepared for market, 17 million tons (33 1/3 percent) was prepared by the use of acid mine water treated with lime.Mine water from underground workings is pumped, drained, and stored in huge quantities. The mine-drainage systems in the anthracite region handle over 200 billion gallons of water annually, of which 150 billion gallons is pumped to the surface. More than 69 billion gallons of water is impounded in underground pools (1). Much of this water is employed for breaker use, dust-control installations; hydraulic backfilling, combatting mine fires; and aiding in the transportation of anthracite in gently dipping places where sheet iron is used Roos(4) estimates that 1,100 gallons of mine water is utilized in the preparation of anthracite mined."

Nov 1, 1946

By D. C. Anderson

Utah Construction & Mining Co.'s Lucky Mc mine is one of the major uranium producers in the United States. It is located near the geographic center of Wyoming in Fremont County. The climate is middle-latitude steppe, with an average annual precipitation amount of 10 in.; the temperature varies from 40º below zero to 100º above. The land surface is moundlike, rolling terrain, with sparse grass and sagebrush. The northern slopes of the higher ridges support a scattering of juniper and pi[n]ion growth. DISCOVERY The discovery was made by Neil E. McNeice, of Riverton, Wyo., on Sept. 13, 1953. After prospecting the area and staking a few claims, McNeice reported his findings to geologists of the Atomic Energy Commission (AEC), who immediately began preliminary studies of the numerous surface uranium exposures of the district. The discovery received widespread publicity, resulting in an intensive search for uranium throughout the region ; thousands of claims were staked. The AEC drilled several shallow holes near the discovery outcrop. Assays of cuttings from these holes confirmed the presence of a low-grade, oxidized uranium deposit. McNeice and his partner, L. A. Morfeld, tried to start a mining operation but were plagued by a lack of capital and technical know-how. They sought assistance from a Salt-Lake-City-based mining firm, the New Park Mining Co., engaged in underground base-metal mining in the Park City district of Utah. After a period of negotiations, New Park initiated activities that led to the forming of the original Lucky Mc Uranium Corp. The company started limited development drilling and mining operations in the summer of 1954, with the first ore production being shipped by truck to the Vitro mill in Salt Lake City. The mining

Jan 1, 1969

By John G. Roscoe

Continental Materials Corp. operates two under- ground uranium mines in the Crooks Gap district of central Wyoming. Both mines are developed as slusher mining operations through vertical shafts with single level haulage to slusher pocket loading stations. In general, operations at both mines are similar except for depth and some minor details. The shafts are identical in cross-section, each with a 4 ½ x 5-ft hoisting compartment and a 4 ½ x 5-ft manway. Kimberley-type skips are loaded from measuring pockets through air-operated guillotine gates. The Seismic shaft is 245 ft deep and the Reserve shaft depth is 585 ft. The Seismic shaft was sunk in 1957 and the mine has been producing 200 tpd since 1958. The Reserve shaft was sunk in 1960 and the mine is still in the development stage. The hoists of both mines are equipped for semi-automatic operation; that is, they are mechanically controlled to perform a certain cycle of duty and then stop until another cycle is manually initiated. The Seismic hoist, however, was originally a conventional, manually controlled unit; the reserve hoist was installed as an automated system.

Jan 7, 1962

By T. W. Sullivan

"This paper explores the history of AC static variable frequency control drive systems on open cast mining machinery, in particular electric mining shovels and electric walking draglines, over the past ten years. It critiques the peformance of these drive systems from a productivity and operating cost standpoint and evaluates the over-all success of the original design concepts as they were envisaged in the 1970s. The paper details the state-of-the-art as it exists today as well as design improvements contemplated for the immediate future.IntroductionConsidering the fact that the very first successful application of an alternating current electrical distribution system occurred at the Gold King gold mine near Ames, Colorado, U.S.A., in the year 1891, it seems somewhat ironic that almost 100 years later, AC excavator drive systems are just now becoming commonplace in the mining industry.If one were to read the biography of Lucien L. Nunn, the first person to successfully install a commercially viable alternating current power distribution system, one would quickly visualize a parallelism between his fight to achieve acceptance of his new lower cost technology and that of those commissioned with the belief that AC static variable frequency control drive systems are not only a better performing, lower cost drive system for mining excavators today, but moreover, the drive systems of the future in our industry.This paper will deal with the evolution and incorporation of AC static drive systems on open cast mining excavators. It will trace the history of the development of these drive systems in the mining industry, the current state-of-the-art concerning these systems, and what the future holds for these excavators in our industry."

Jan 1, 1990

Prevent the explosion of methane gas or coal dust by replacing air with inert gas inside highwall mine excavations. Approach Use combustion gases as a source of inert gas with low oxygen content to blanket the cutting, head of highwall mining machines. This gas is placed strategically at the collar of the excavation where it enters the hole to replace the mined coal volume. The elimination of oxygen from the hole prevents explosions of gas or dust. How It Works Highwall mining methods arc used when surface mining becomes uneconomical. One method of highwall mining involves use of a horizontal auger to enter the coalbed from a surface mine bench. The coal is mined in a series of horizontal, parallel, and large-diameter holes. Historically, little methane has been associated with auger mining. However, mining technology has extended the reach of auger mining, which can increase the occurrence of methane. Methane explosions at auger mining operations have been increasing. Methane has been the primary fuel source of these ignitions, but coal dust also may have been involved.

Jan 1, 1993

By M. Javier

"Mining makes civilization possible. It also creates socio-environmental liabilities forcing us to ask how much more of this mining can our planet support. It is clear that the future of mining differs from mining in the future. The laws of nature are being compromised by mining. This paper studies the problems at the core of the mining business which need to be addressed. What kind of mining will serve our existence with nature on this planet? What kind of mining perspectives are we able to formulate without having negative effects for future generations? Is mining technologically sustainable? The values of predictions, imagination, and creativity must be integrated to define what mining should be. Those values should be in the technologies necessary to restoring equilibrium of nature (Geomimic) as well as in complete extraction of metals, better utilization of the mineral reserves, and design the usage of metals to recycle. The purpose of this research is to examine many views and perspectives for future generations and to accelerate the pace of innovation of having mining without socio-environmental liabilities by design and by understanding nature. KEYWORDS: Geomimic, Sustainability, Waste mine Design, Management by Loss. INTRODUCTION The future of mining is being stifled by many antiquated and stagnant attitudes and policies by the industry and society as a whole. The time is now or never for real action and education against these attitudes and to upgrade them to meet the current needs of this planet if we are to survive. Doing this will prove that we understand and respect nature for us and our posterity. It will also show a positive assessment that the mining process can be reversed before the point of no return. And that is to say, only if reversibility is still an option. It may not be anymore but it’s worth a try. We need to use our imagination and engineering know-how to come up with new proposals to change the core of mining. It would entail re-engineering. There is a profound difference between the future of mining and mining in the future. The future of mining is the continuation and persistence of past practices in the industry and expecting new results. Mining in the future requires a paradigm shift for extraction through modern thinking about mining as it pertains nature. The new paradigm for mining in the future would restore equilibrium with nature. Always keep in mind the connection of mining to nature. What is the future of nature? To predict mining in the future we need to use past experiences in mining and our knowledge of modern science and engineering to formulate a prototype that will enhance mining while maintaining equilibrium with nature. Mining and protecting nature are not mutually exclusive. This new prototype has nothing to do with the level of bonding or insurance that the mining industry can legally provide. The goal of this paper is to contribute some new ideas to help transform the mining industry based on the laws of nature and its limitations. Using this new prototype we will develop the following 1. Extraction of minerals Reserves-Dimensions-Technologies 2. Usage of mineral resources-Manufacture’s products designed to be reused and recycled 3. Nature- Equilibrium (physical, chemical and biological)"

Jan 1, 2016

By Cyril Wells, Robert F. Mehl

THE practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out 1,13 This importance ties chiefly, though by no means only, in the study of carburizing and in the study of reactions involved in the eutectoid inversion in steel The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in y-Fe and their mutual effects are measured with precision The present paper reports the results of meas¬urements of diffusion coefficients D of manganese in -y-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients [$] Data on the rate of diffusion of manganese in y-Fe have been reported by Fry2 and by Paschke and Hauttmann 3 Claussen4 calculated the diffusion coefficient D from Fry's data as 3 X 10-10 sq cm per sec at 960°, which will be shown to be incorrect by many orders of magnitude Paschke and Hauttmann gave a rough value of 9 6 X 10-8 sq cm per sec at 1400° Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon METHOD AND MATERIALS Method -The method employed is identical with that used earlier 5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded The diffusion anneals were performed in argon, except one (test 18) in which hydrogen was employed for purposes noted below The temperatures reported are accurate to about 3° and constant within I°C , the diffusion times are reported to the nearest half hour The specimens were furnace-cooled after the diffusion anneal at about 2° per min Layers, usually 0 004 in thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0 01 per cent Mn, the distances of these layers from the interface was measured to ±0 0002 in The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions e The D values calculated by these two methods do not differ appreciably 5 The Grube solution was used except in tests in which the effect of concentration upon D was greater than 50 per cent, in such cases the Matano method, which explicitly provides for the variation of D with concentration,1 is the more reliable In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer In 3 of the 30 tests, however, this is not justified, and the D values

Jan 1, 1941

E. W. King, Bozeman, Mont.: The form of measuring up ore in sight looks very plausible, as illustrated in the paper of Mr. Emmons, but from my experience of many years of mining in Montana and Nevada, I have found it is very hard to measure up anything nearer than a guess of what you have in sight, except in the case of a true vein, or a flat vein where the boundaries are well defined. I have been interested in several miues with Dr. A. R. Ledoux, and I know that my foreman and myself, going into the mines and using our best judgment, could seldom see more than 30 days' supply actually in sight, and yet we were running from 100 to 250 tons a day, and keeping it up year after year. Prof. John D. Irving, New Haven, Conn.: I understand from Mr. Emmons that this is a method which has been found applicable in the copper-mines in Tennessee, where the record could be made with a good deal of accuracy, and where the work in the mines allowed the necessary development to be done, so that the record could be kept up. I do not think there was any intention in his mind to imply that this was applicable to all cases, especially such as Mr. King has mentioned. President Charles Kirchhoff, New York, N. Y. : I think the point is that the paper impresses the necessity for doing it where the possibilities exist. There has been too little attention given to this very matter, particularly in the United States; but I think our English friends are following it very much more zealously, and the demand for it there is possibly greater than it is here, because English boards of directors handle mines that are often very much further away than our own are, and the English public and the English engineers generally are very much more insistent upon seeing how much longer current dividends are going to last, or current assessments are going to continue.

Jan 1, 1913

By Rachel Bauer, Jacob Henderson, Dr. Catherine Johnson

Capital Quarries in Owensville, Missouri faces several challenges when designing a blast that allows for ease of movement while maintaining controlled throw and compliant air over pressure. The primary challenge is the nearest non-owned structure (NNOS) is a residential home located 250 feet from the quarry. Another challenge is a production bench which is 100 feet tall and separated from the NNOS by Pennsylvanian fire clay that filters out high frequency waves from the blast. Material from the blast must also be less than 5 inches in order to be processed by the crusher in the quarry. To provide as much relief as possible, production shots will consist of a single row with the minimum required burden. To design the shot, signature hole analysis was used to determine the optimal timing between powder columns. Electronic detonators provided an accurately timed shot to minimize the amplitude of the vibrations while maximizing the frequencies. Boretraking and 3D profiling with Renishaw laser profiler and Strayos drone photogrammetry provided an accurate burden measurement. Powder factor was kept at 1.3 tons/lb using bulk emulsion. The boreholes were split into 5 powder columns with the top of the hole firing first in order to blast to floor grade. The resulting shot produced good fragmentation and shot to floor grade. Seismograph readings showed air over pressure vibrations within legal limits. Due to this success, multiple shots will be designed using the process described.

Feb 6, 2023

By H. L. Riley, B. W. Gandrud

AS far as the present writers know, this system of flotation has not been used elsewhere in this country, but in the last couple of years it has been introduced, with minor variations, at one plant in England and one in Wales.' The system has been described and discussed in a number of publications.2-5 The following is quoted from an abstract of the latest of these,5 a paper presented at an International Conference on Industrial Combustion in 1952. On the basis of experience to date with the commercial plants, it is believed that the kerosene-flotation process incorporates all the necessary elements to make it greatly superior to anything else now available for treating of fines in wet processes of coal preparation. Additional study and investigation are still needed, however, to determine if certain phases of the process can be improved to such an extent as to make it generally satisfactory and acceptable to the industry. Further improvements will be needed with respect to the capacities of the flotation cells and the reagent consumption. The situation referred to above explains why an investigation is being made of the possibilities of achieving better cell capacities. Results obtained from this investigation, which is still in progress, are believed significant with regard to both cell capacity in general and the relation of cell design to cell capacity in particular. Commercial equipment now being used in a laboratory-type investigation should have performance characteristics similar to those of the larger machines. Equipment and Procedures: All flotation tests have been made in a standard Denver sub-A 24x24-in. unit cell of 12-cu ft volume. Cell modifications to make it more suitable for the tests were an adjustable front-wall section for varying cell depth and a perforated scraper-drag assembly for removal of the float product. There is also an apron dry-coal feeder, a gravity-feed water supply, reagent feeders, and a centrifugal pump that feeds the mixture of coal, water, and reagents into the flotation cell. A wattmeter connected into the drive-motor circuit records the power requirements of the impeller throughout each run. Dry coal, water, and reagents are all fed through a pan-type intake to the feed pump. A Sturtevant blower was set up to furnish air for supercharging. A centrifugal pump with a garbage-can intake provides for disposal of refuse flow to an outside settling tank. Figs. 1 and 2 show the flotation cell; Fig. 2 also illustrates the blower for supercharging. For purposes of this investigation, the percentage by weight of the feed coal recovered in the float product under a standard set of conditions has been considered as the criterion of cell capacity. The authors realize that such a criterion may be somewhat unorthodox, as the term cell capacity is usually understood to refer to feed input and ordinarily takes into account the ash analyses of the float product and refuse. However, the word capacity is flexible enough so that Webster gives one definition as maximum output, a definition which seems to justify, at least partly, acceptance of the above criterion. It has been the authors' experience in the Birmingham district that the ash-reduction efficiency of the coal-flotation process is generally satisfactory and that the only real problem is to increase the rate of float recovery so that the feed rate to any given bank of cells can be increased without undue loss of coal in the refuse. Originally it was planned to operate the flotation cell to simulate continuous operation during sampling periods. It was assumed that operating for reasonable time with feed coal, water, and reagents turned on would stabilize conditions so that the weight of float coal discharged during a fixed time interval would be an accurate measure of the rate at which the coal was being floated. It developed, however, that this supposition was erroneous. The float coal, caught for fixed time intervals and weighed, gave widely varying results in duplicate runs. Efforts to correct this trouble failed, and it was decided to try to operate on a batch-test basis, whereby all the float coal produced during a run on a known weight of feed coal would be caught in tubs, dewatered, and weighed. This method gives consistent and reproducible results, with total float product weight rarely varying by more than 3 or 4 pct on duplicate runs. The standard test procedure is as follows: A 132-lb sample of dry feed coal is weighed and placed in the feed hopper. The feeder is adjusted for a rate of 800 lb per hr. Feed water and reagents are turned on, and the feed and refuse pumps are started. One minute later the impeller is started. Six minutes are allowed for the cell to fill up with the water-reagent mixture. The feed of dry coal is started at the end of this 6-min period. One minute later the float-coal removal drag is started. The float coal is caught in one tub for the first 6 min after the flow of feed coal starts. Tubs are then changed, and the float coal is caught in a second tub until the feed coal runs out, when the tubs are again interchanged to catch the float coal for the remainder of the run in the first tub. The cell is kept running for 3 min with the water and reagents on after the feed stops to allow residual float coal to be removed. At the end of a test the wet float coal in both tubs is weighed and the total weight recorded. The product in the second tub is used for moisture determination and screen-size analyses. When the

Jan 1, 1956

JAMES GAYLEY (President), R W RAYMOND (Secretary), FRANK LYMAN Treasurer) T A RICKARD NEW YORK, N Y CHARLES H SNOW NEW YORK, N Y R W RAYMOND NEW YORK, N Y (Terms expire February, 1906 ) JAMES GAYLEY NEW YORK, N Y FRANK KLEPETKO NEW YORK, N Y FRANK LYMAN NEW YORK, N Y (Terms expire February, 1907 ) JAMES DOUGLAS NEW YORK, N Y JAMES F KEMP NEW YORK, N Y ALBERT R LEDOUX NEW YORK, N Y (Terms expire February, 1908 ) Council PRESIDENT OF THE COUNCIL JAMES GAYLEY VICE-PRESIDENTS OF THE COUNCIL GEORGE W MAYNARD NEW YORK, N Y JULIAN KENNEDY PITTSBURG, PA CHARLES D WALCOTT WASHINGTON, D C (Terms expire February, 1906 ) WILLIAM P BLAKE TUCSON, ARIZ THOMAS F COLE ,DULUIH, MIFF IRVING A STEARNS WILKES-BARRE, PA (terms expire February, 1907 )

Jan 1, 1910

By Karl A. Gschneidner

Magnetic refrigeration was first used in the mid-1920's and new developments seem to have taken place about every 20 years, and this is especially true for the mid-1990's. The active magnetic regenerator magnetic refrigerator has the promise to become the first practical machine utilizing the magnetocaloric effect for cooling (and also heating). The basic principles are briefly discussed. Since the temperature lift for the magnetocaloric effect spans about 50 K, one will need to utilize several ferromagnets with different magnetic ordering temperatures in order to reach temperatures below ~250 K. The basic properties, behaviors, limitations, and new phenomena and knowledge are discussed.

Jan 1, 1997

By S. Dinda

A series of as -quenched 4340 bars were drawn through a carbide die to various reductions. The X-ray diffraction technique of Lopata and Kula was employed to detect preferred orientation in drawn martensitic steel bars with low amounts of deformation, as lord as 0.8 pct The specimen face of each bar examined was cut at a 45-deg angle to the bar axis. The reflecting planes in the 45-deg face were varied by appropriate rotation of the sample using a spectrogonionzeter. TIE X-ray bean of a diffractometer was reflected from the center of the bar and the diffracted intensity was delected with a proportional counter and recorded. Intensity peaks were developed by cold working for 110 planes oriented at 0 and 60 deg to the bar axis. The intensity peaks increased with increasing defortnalion us a preferred orientation with a 110 texture developed parallel to the drawing direction. The intensity peaks for deformed as-quenched specimens remain unchanged after tempering at temperatures as high as 1000°F. The same amount of preferred orienlalion was observed both inferritic (hot-rolled) and martensitic (as-quenched) structures after an equivalent amount of deformation. THE deformation of martensite with medium carbon content. less than 0.5 pct, has been studied by Breyer et a1.1,2 It was reported that changes in properties such as resistivity, carbide precipitation, and the introduction of a yield point phenomenon were produced after cold reduction of as-quenched AISI 4340 steel bars. Later, Breyer and Nachtman3 studied the effect of cold reduction upon X-ray line intensity. They showed that the integrated 110 line intensity increased with increasing deformation when the planes examined were perpendicular to the die drawing direction. The integrated 110 line intensity for planes oriented at 45 deg to the die drawing direction, in contrast, were found to slightly decrease. These changes were proposed to be consistent with the previously proposed model of a stress-induced ordering of carbon atoms in the vicinity of dislocations.1,2 Objections can be raised to the above interpretation of the X-ray results on two grounds: a) Rough structure factor calculations indicate that the intensity changes are too large (50 pct observed vs 2 pct calculated4,5) to be the result of changes in the location of iron atoms produced by the stress-induced ordering of the carbon atoms. b) The results might be explained in terms of preferred orientations, although X-ray evidence of the development of texture has not been reported in the literature for deformations as slight as 1 or 2 pct. The aim of the present work was to determine if preferred orientation was present in such cold-drawn martensitic steel bars. In drawn rod or wire there is generally a certain crystallographic direction which is aligned in the direction of the wire axis, and the crystallographic planes are distributed symmetrically around this "fiber axis".6-8 This type of cylindrical specimen, with the fiber axis located at the center, will show rotational symmetry. Lopata and Kula9 proposed an experimental method utilizing a specimen cut at 45 deg, see Fig. 1. The X-ray beam is diffracted from the center of this bar cross section. The specimen is rotated around an axis perpendicular to the bar axis and lying in the 45-deg cut face. This permits the angle between the normals to the reflecting planes and the bar axis to be varied from 0 to 90 deg.9 With this arrangement the errors due to absorption and irradiated volume compensate each other.' This greatly simplifies analysis of the data and is of considerable advantage for quantitative measurements. If there is preferred orientation in the specimen, more planes are oriented in a particular direction in the bar. When the bar is rotated to the favorable Bragg condition for that particular orientation, the intensity will be higher than that for some other angle. This technique was adopted for the present investigation.

Jan 1, 1969

By Dipl. -Ing. H. -J. Sager

The ‘Westerschelde Tunnel’ underpasses the estuary of the Schelde in the Netherlands. The tunnel will consist of two tubes which are driven by two hydroshields (slurry shields). The tunnels will each have a length of approx. 6.6km and a bore-diameter of 11.33 m. Demanding ground conditions had to be considered during the design of the shield machines. Loose sands, extensive clay formations and high ground water pressures of up to 6.5 bar will be encountered during the tunnel drive. The tunnelling activities will start in the middle of 1999 and are scheduled to end by the end of 2001.

Jan 1, 1999

By Clarence Zener

IT has long been known that the density of a metal usually decreases with cold-work. Thus O'Neill1 observed as early as 1861 that cold hammering of commercial hot-rolled copper is accompanied by a decrease of density of 0.2 per cent, and that subsequent annealing restores the original density. The origin of this density change, however, has remained obscure. In particular, experiment has not yet decided whether it is due to the presence of small cavities and an increase in intergranular surface or to an actual expansion of the lattice itself. This uncertainty in the origin of the change in density is a reflection of our uncertainty as to the changes induced in a metal by cold-working. One school regards cold-working as a breaking up of the original grains into a large number of perfect crystallites somewhat randomly orientated with respect to one another.2 According to this viewpoint, the mere introduction of a large intercrystallite surface induces a net volume expansion. Another school regards cold-working primarily as a distortion of the grains. It is not obvious that this second viewpoint will lead to a net volume expansion. The purpose of the present paper is to show that this is indeed the case, and that this expansion is of the right order of magnitude to explain existing experimental data. The physical basis for the association of an expansion with distortion lies essentially in the variation of the elastic moduli with volume. This variation is considerable. Thus from Table I we see that a I per cent increase in volume for the case of copper will decrease the bulk modulus K by i0 per cent, the shearing modulus µ by 3.8 per cent. If we thus twist a rod through a given angle, we shall do less work upon it if it increases slightly in volume, thereby reducing the torsion modulus that involves as a factor the shearing modulus. A general principle' in physics states that the rod will so adjust itself as to have a minimum potential energy consistent with the end restraints. It will therefore expand. [ ] In order to obtain a quantitative comparison with experiment, we follow Maier4 in comparing the lattice expansion with the latent energy of cold-work. This latent energy has been measured directly by Taylor and Quinney5 on copper rods subjected to torsion, and may amount to as much as 15 per cent of the total work done upon the specimens. We shall assume that this

Jan 1, 1941

By Francisco Alberto Marreiros da Rocha Filho

A corrosão é um fenômeno que está intimamente ligado à integridade dos metais e de suas ligas. Esta ocorre de diversas formas, uma das principais é a corrosão localizada na forma de pites, objeto de análise desse estudo, que visa estabelecer um comparativo entre as curvas de polarização cíclica de algumas ligas ferrosas e não ferrosas, ensaiadas em solução de NaCl 0,6 M, mostrando a agressividade que a solução exerce sob cada uma das ligas. Os materiais analisados nesse estudo foram os aços inoxidáveis AISI 304, AISI 444, super duplex ASTM A890/A890 M Grau 6A, o aço carbono AISI 1030, o alumínio comercialmente puro, o cobre eletrolítico e a liga zircaloy- 4. Inicialmente foram medidos os potenciais de corrosão (Ec) de cada liga através do monitoramento do potencial de circuito aberto. Foram realizados os ensaios de polarização potenciodinâmica cíclica em cada liga, comparando o aspecto superficial antes e depois do ensaio através de micrografias óticas, possibilitando que fossem observadas as diferenças entre cada material quanto à resistência à corrosão por pites. Observou-se que algumas ligas não apresentam passivação como o caso do alumínio comercialmente puro, e outras apresentaram regiões passivas e histereses bem definidas, ficando evidente que, dentre as ligas analisadas, o aço inoxidável super duplex ASTM A890/A890 M Grau 6A apresentou os melhores resultados frente aos efeitos agressivos dos íons Cl- presentes na solução, sendo o menos suscetível à corrosão por pites.

Aug 17, 2017

By Wilson CJN

The central Taupo Volcanic Zone is a region of intense Quaternary silicic volcanism accompanying rapid crustal extension. Modem central TVZ is the most frequently active and productive silicic volcanic system on Earth, erupting rhyolite at c. 0.28 m' s'. The rhyolites show no major compositional changes with time, but the total extent of magma chamber zonation has changed with the advent of rifting and crustal extension at c.0.7 Ma. At least 34 caldera-forming ignimbrite eruptions have formed a complex sequence of relatively short-lived, nested and/or overlapping volcanic centres in central TVZ. Taupo contrasts with other large silicic magmatic systems in the exceptionally high frequency, but small size, of caldera- forming eruptions. This contrast reflects the thin, rifted nature of the TVZ crust, that precludes the development of long- term magmatic cycles at Taupo.Within central TVZ, non-rhyolitic compositions have been erupted apparently irregularly in time and space; in particular there is no evidence for a geographic separation of basalts from andesites. TVZ is a rifted arc, but its segmented nature, high thermal flux and voluminous rhyolitic volcanism make it unique on Earth.

Jan 1, 1995

By William W. Adams

The quarrying and related industries of the United States improved their safety record in 1938 by reducing their accident-frequency rate to a lower acid more favorable position than it has occupied at any time except 1935 since comparable accident statistics became available in 1916. The rates for 1935 and 1938 were identical. The number of men employed in 1938, although smaller than in 1936 and 1937, was larger than in any other year since 1930. Volume of employment, as measured by the number of man-hours worked in the industry as a; whole, likewise was larger than in any year since 1930 except 1936 and 1937. Reports from operating companies to the Bureau of Mines, United States Department of the Interior, showed that 77,497 men were employed in 1938, a decrease of 6,597 compared with 1937. This figure represents the average number of employees for the period during which the quarries and plants were active during the year, which in 1938 averaged 223 workdays per employee compared with 241 in 1937. A total of 17.3 million man-days or 133.8 million man-hours of work was shown for the industry as a whole, which indicated a weighted average of 7.75 hours per man-shift. Reports for 1937 showed a total of 158.3 million man-hours for the entire industry and an average workday of 7.81 hours. Accidents resulted in the death of 82 employees, 5 more than in 1937, and in 5,027 nonfatal injuries involving disability for more than the remainder of the day on which the injuries were received. The number of nonfatal injuries was 1,321 less than in 1937. As the number of deaths and injuries was reduced more, proportionately, than man-hours of employment, the accident-frequency rate per million man-hours of work declined, the rate for 1938 being 38.19 compared with 40.59 for 1937. In other words, accident occurrence to the average employee was 6 percent more favorable in 1938 than in 1937 on the basis of actual number of accidents and actual number of man-hours worked during the 2 years.

Jan 1, 1940

By A. J. Lewis, P. J. Hutcheson, M. E. Robertson, P. A. Moir, K. M. Barfoot

With the content of gold and platinum in the vast majority of ore deposits typically averaging 6 parts per million and less, the accurate and precise measurement of these metals in samples of ore and mining process streams has proven very difficult to achieve by modem spectroscopic analytical techniques. Largely because no other technique has proven suitable, the basic fire assay process has become the accepted international standard for these metals. Fire assay, however, suffers a number of disadvan­tages in the modem, competitive, high technology, and increas­ingly environmentally aware world. It is a labour intensive technique that is difficult to automate, and requires high levels of skill to ensure accuracy and consistency of results. Potentially hazardous chemical reagents are employed, of which, lead, in particular, can be a serious source of contamination to both personnel and the environment if not effectively controlled. Other dangerous elements, such as mercury and arsenic, liberated in high energy furnace operations, are further sources of possible health and pollution hazards. n contrast, the energy dispersive K X-ray fluorescence (K­XRF) technique devised by K X Technology Ltd overcomes many of the technical constraints of conventional low energy X­ray analysis, and has the potential to revolutionise assay opera­tions in precious metal mining. The technology is simply automated, requires basic operator skills, uses no chemicals, consumes less than 20kW, and is capable of detecting gold and platinum to an accuracy of O .1 parts per million by mass. The new third generation design of AZTEC laboratory instrument, released in 1994, is the result of significant technical development. Capable of analysing over 1200 samples per day, and developed primarily for grade control sampling, its applica­tions have spread to gold ore accounting from on-line conveyor belt sampling; screening of exploration samples; measurement of gold in carbon granules for Carbon-in-Pulp process control; and for conducting rapid checks to support key managemen decisions. The economic, rapid, and non destructive analysis ofup to 80g of ore for large numbers of samples, reduces sampling and sub-sampling errors, and provides improved grade estimates for ore bodies. When interfaced to a LIMS, laboratory automation and cost-savings can be further enhanced. The AZTEC design is also being modified for the analysis of platinum. The GOLDSTREAM on-line analysis system is an important new application of K-XRF to the continuous monitoring of process streams in gold ( or platinum) plants and mills. Integrat­ing the technologies of K-XRF to measure total gold, and dissolved gold spectroscopy to measure gold in solution, the insoluble fraction of gold can be deduced, and the effectiveness of the extraction process determined. Slurries are sampled automatically from selected points of the plant and pumped to the system for analysis. The information produced forms the basis for plant control and optimisation.

Jan 1, 1995

By J. Gordon Scott

The Iron Ore Company of Canada has now been operating a computer for the grading or blending of direct shipping ores for two years. This paper deals with the computer application pertaining to the grading of direct shipping ore. It consists of five sections. The first part deals briefly with a description of the operation of the Iron Ore Company of Canada; the second with the source and flow of the various data required to grade or blend ore; the third briefly outlines the computer programs used in this application; the fourth illustrates the mathematical approach used to properly blend ore. The final section briefly describes other technical computer programs.

Jan 1, 1964