Search Documents

By Hamid-Reza Manouchehri, Hassna Aitahmed-Ali, Stellan Sundberg

"In flotation practices as the particle size becomes fine, e.g., p<20µm, the process efficiency declines markedly. When flotation of fine particles is necessary, one method to improve the recovery is selective agglomeration of fines. Different agglomerating methods have been introduced and tested; however, one method which has recently received great attention is to aggregate fine particles by magnetic force. A selective aggregation of the fine paramagnetic particles, e.g., sulfide minerals, can be achieved by applying a high intensity magnetic field during flotation conditioning. The method is simple, selective and effective for fines, and has a low operation cost. However, a minimum magnetic susceptibility of fine grains is required for this process. This method has been demonstrated in different sulfide minerals flotation plants. The implementation of the magnetic conditioning device, ProFlote, in both the Cu-Pb and the Zn circuit of Boliden’s Garpenberg plant in Sweden, where a complex massive sulfide ore is treated, is discussed herein. The preliminary results have shown an increase in the recovery of value minerals, in particular Zn and Ag and considerable reduction in Zn deportment to the final tail. Increases in Cu grade and decreases in Pb grade in Cu-con have been achieved as well."

Jan 1, 2014

By D. H. Chambers

The Bureau of Mines developed a process for producing high-purity zinc and tin by electrorefining from liquid amalgams. Commercial grade metals were dissolved in mercury to produce saturated amalgams at room temperature. Amalgams were also prepared by electrolytic transfer from soluble anodes of the metals to a mercury cathode. Amalgams formed by both methods were used as anodes in electrorefining cells to produce high-purity cathodes. Metal impurities, excluding mercury, were at levels of less than 5 ppm in zinc and 9 ppm in tin. Mercury content was about 2 to 10 ppm in zinc products, and this was effectively removed by heating the cathodes in a vacuum. Mercury was excluded from tin cathodes by pumping the tin electrolyte through tin turnings and controlling the cell temperature.

Jan 1, 1969

By E. B. Snyder, H. M. Kraner

This paper shows that volume stability, low porosity and decreased pyroplasticity are desirable for blast-furnace linings, partitularly for the hearth. It shows further that a hot load test is a valuable means of testing the fusion or softening behavior of a refractory at operating temperatures. The effect of carbon monoxide on commercia1 blast-furnace refractories in their as-received condition and after refiring is reported, showing that many commercial blast-furnace refractories disintegrate badly but that refiring decreases the effect and certain special refractories are now available which are almost free of the tendency. Factors Affecting Choice of ._ Refractories If one were to depend entirely upon experience or trial in the selection of clay refractories, the solution of a problem would be a slow process. Furnace campaigns are so long and attended by so many variables that it is difficult to draw fine distinctions within a reasonable period of time in regard to the quality of refractories used. It could be said, of course, that if service results do not yield the proper information for intelligent choice, there is no difference in the quality of brick being considered, but this is not necessarily true. Conventional ceramic tests are designed to give the ceramic engineer information as to the refractoriness and firing tempera- . ture, which he in turn internrets in terms of volume stability, ability to withstand load at high temperature (pyroplasticity), permeability, chemical stability and re-. sistance to the action of slag. In most refractory applications . several of these factors are involved. In a particular instance, one requirement may be predominant, while in others some other factors may be of primary importance. In this country, clay refractories are generally made from mixtures of plastic and flint fire clays. The process of firing a clay refractory is one of slowly melting the constituents, and during this operation its porosity is gradually reduced. The process is arrested, of course, in its incipient Stages and the Progress is determined by measuring slight changes in porosity, volume, bulk gravity, etc., that have taken place. Often the temperatures to which clay refractories are exposed in service are higher than those employed in their firing. However, if the manufacturer were to fire them at such high temperatures the brick would distort. Therefore it would be difficult for the manufacturer to fire all of his clay refractories to temperatures at which they are to be used, although in many cases it would be desirable from the user&apos;s point of view if he would do so. The porosity of clay refractories decreases by firing, to a minimum limit, after which a further increase in the temperature causes expansion in certain clay constituents and bloating in others. Both may occur in the same refractory containing two such clays.

Jan 1, 1944

By H. M. Kraner, E. B. Snyder

This paper shows that volume stability, low porosity and decreased pyroplasticity are desirable for blast-furnace linings, partitularly for the hearth. It shows further that a hot load test is a valuable means of testing the fusion or softening behavior of a refractory at operating temperatures. The effect of carbon monoxide on commercia1 blast-furnace refractories in their as-received condition and after refiring is reported, showing that many commercial blast-furnace refractories disintegrate badly but that refiring decreases the effect and certain special refractories are now available which are almost free of the tendency. Factors Affecting Choice of ._ Refractories If one were to depend entirely upon experience or trial in the selection of clay refractories, the solution of a problem would be a slow process. Furnace campaigns are so long and attended by so many variables that it is difficult to draw fine distinctions within a reasonable period of time in regard to the quality of refractories used. It could be said, of course, that if service results do not yield the proper information for intelligent choice, there is no difference in the quality of brick being considered, but this is not necessarily true. Conventional ceramic tests are designed to give the ceramic engineer information as to the refractoriness and firing tempera- . ture, which he in turn internrets in terms of volume stability, ability to withstand load at high temperature (pyroplasticity), permeability, chemical stability and re-. sistance to the action of slag. In most refractory applications . several of these factors are involved. In a particular instance, one requirement may be predominant, while in others some other factors may be of primary importance. In this country, clay refractories are generally made from mixtures of plastic and flint fire clays. The process of firing a clay refractory is one of slowly melting the constituents, and during this operation its porosity is gradually reduced. The process is arrested, of course, in its incipient Stages and the Progress is determined by measuring slight changes in porosity, volume, bulk gravity, etc., that have taken place. Often the temperatures to which clay refractories are exposed in service are higher than those employed in their firing. However, if the manufacturer were to fire them at such high temperatures the brick would distort. Therefore it would be difficult for the manufacturer to fire all of his clay refractories to temperatures at which they are to be used, although in many cases it would be desirable from the user&apos;s point of view if he would do so. The porosity of clay refractories decreases by firing, to a minimum limit, after which a further increase in the temperature causes expansion in certain clay constituents and bloating in others. Both may occur in the same refractory containing two such clays.

Jan 1, 1944

By J. W. Spretnak, G. W. Cunningham

A study has been made of the growth and disappearance of voids in the interface of pressure bonded copper. The formation of visible voids is primarily due to spheroidization and coalesence of microvoids produced during the application of pressure. The microvoids could be prevented from forming by the application of high pressures or by increasing the ductility of the copper. Migrating grain boundaries were found to be more effective in void removal, than stationary grain boundaries. DURING the course of an investigation on the mechanism of pressure bonding, it was found that voids formed in the bonding interface which inhibited migration of the interfacial boundary and grain boundaries in the bond region. Therefore, an effort was made to determine the nature of the voids and how they form, grow, and disappear. This paper reports the results of such an investigation. The existence of interfacial voids is not solely a characteristic of massive components of metal which have been bonded by the application of heat and pressure, but is a phenomenon which has been observed in sintering as well. Simonsen attempted to study the sintering process by hot-stage microscopy and thereupon observed the formation of interparticle porosity as sintering proceeded. It was assumed that the porosity was due to grooves created at the location where grain boundaries joined the surface of the particle. Pranatis, Castelman, and seigle2 have also observed voids along the areas of contact in wound-wire specimens used for sintering studies. They did not discuss the point in detail since this behavior was not general, but they did suggest that the voids might develop as a result of stresses along the interparticle contact area. In previous investigations on pressure bonding, workers3 have suggested that voids may exist in the region where mating surfaces are placed in intimate contact, but the existence of the voids was not verified and no attempt was made to study the growth and disappearance of these voids. Durst noted the existence of pores in roll-clad structures prepared by cold reducing two sheets to force them in contact and then annealing to improve the bond. Since his unbonded regions contained a gas which he assumed to be insoluble, he proposed a mechanism which consisted of spheroidization of the unbonded regions and a growth of the contact area, but no speculations were made regarding disappearance of the gas filled pores. One interesting comment made by Durst was the suggestion that flattened voids with sharp corners which are produced during roll bonding will have a greater driving force for spheroidization than the more rounded pores created by pressing metal powders and thus spheroidization and neck growth will occur at lower temperatures. In this study it was necessary to demonstrate conclusively that voids can actually exist in the interfacial bond area. Experimental work was then directed toward a study of the mechanism whereby the voids grow and subsequently disappear.

Jan 1, 1963

By D. S. Holmes

Biological processes for metal solubilization and ore beneficiation are in widespread use today. There are also some promising new applications of biotechnology in the areas of metal concentration and toxic metal cleanup. Recent progress in genetic engineering promises both to revolutionize the existing biological process and to expedite the adoption of the new biological applications. But before it can do so effectively, progress must be made in many areas of fundamental research and in biochemical engineering. These issues are addressed with special reference to the biotechnology of semi-enclosed containers (bioreactors), dumps, heaps, in situ and under- ground leaching, and with respect to the biotechnology of metal concentration. Finally, certain biological considerations for bacterial strain improvement are discussed.

Jan 1, 1987

By Robert H. Richards

DuRing the winter of 1868-9,I was called upon by Professor F. H. Storer, to put up the Bunsen filter pump in the chemical laboratory of the Masschusetts Institute of Technology. As the laboratory is on the lower floor, it was found necessary to use a great deal of cumbrous pipe and apparatus to get the necessary column. It was then suggested that if an instrun~ent could be devised which would make use of the hydrant pressure in the service-pipe, it would do away with the objectionable features of the Bunsen pump. After using the Bunsen pump for some years, the jet pump to be described in this paper was devised, and it has since been adopted by Prof, Wing in the quantitative laboratory of the school. I am much indebted to Prof. Wing for his aid in starting the manufacture in brass of these jet pumps, whieh are now to be had in Boston. The jet pump much resembles the Giffard injector in form. It, differs from it in the fact that water is the impelling fluid, and air the impelled, while with the injector steam is used to impel water. The principle of condensation of steam, which is availed of in the injector, is entirely wanting in the jet pomp. The jet pump consists in a water jet, w, (see figure), a constriction or waist, a, and a waste tube, o. The success of the jet pump depends on the follow ing conditions: 1. The relation between the sizes of sectional area of a and w. &apos; 2. The proximity of n and w. 3. The form and angle of the two hollow cones whose vertices make the constriction a. 4. The relative size of sectional area of w and o. 5. The zigzags, or an equivalent means of making foam. In the following discussion, let a, w, and o repre sent the diameters of these parts of the jet pump. A number of experiments were&apos; .tried to ascertain

Jan 1, 1879

By Mike Trovant, Stavros A. Argyropoulos

"A fixed grid numerical model for phase change problems is proposed. The model solves for heat transfer and fluid flow, via the coupled solution of the energy, continuity and momentum equations. In addition, the numerical scheme accounts for temperature varying thermophysical properties and determines the shrinkage profile resulting from phase and density change. Simulations are run to determine the effect of varying model parameters and wall cooling rates on the location and shape of the shrinkage void formation in cylindrical casts. Results are shown for both aluminum and magnesium.IntroductionThe mathematical modeling of phase change processes (be they solidification or melting problems) entails solving for many interrelated phenomena. A comprehensive numerical simulation of the casting of a metal, for example, would have to account for: (a) heat transfer in both the solid and liquid portions of the metal and in the mold, (b) the release of latent heat during phase change, (c) fluid flow behavior in the liquid portion of the metal, (d) temperature induced shrinkage caused by liquid contraction and solidification contraction, and (e) the development of thermal stresses with accompanying shrinkage in the solid portion of the cast and mold. A schematic of the relationships that exist between the coupled equations which govern solidification is shown in Figure 1."

Jan 1, 1994

By L. Alan Weakly

The U.S. Department of Energy (DOE) has entered into a $l.5 million Cooperative Agreement with Alpine Equipment Corporation/Astro International Corporation ("Alpine") of State College, Pennsylvania, for the evaluation of water-jet-assisted (WJA) mechanical cutting of oil shale under actual mining conditions. A commercial-sized, heavy WJA mechanical miner is being assembled based upon the successful "factory testing" of a smaller prototype miner utilizing standard tungsten-carbide and Polycrystalline Diamond Composite (POC) bits in large oil shale boulders. Actual field testing of the machine will be conducted in an oil shale mine located in the Piceance Basin of Western Colorado. In-mine logistical support is being provided by several oil shale companies through the Colorado Mining Association (CMA) and the U.S. Bureau of Mines (USBM).

Jan 1, 1990

By Roberts C

The satisfactory testing and characterisation of mineralisation amenable to heap leaching, is of prime importance to successful operation of a project. This paper outlines a methodology for assessing material suitability. A general model is used for classing material types for suitability for treatment and for economic analysis. The four levels of these are overburden, oxide, transitional and unoxidised materials. During exploration, reverse circulation (RC) drilling can be used effectively to define these zones by a combination of logging, analysis and provision of cuttings for column leach and bottle roll trials. RC cuttings can he used effectively for column leach trials, when calibrated against conventional processing-sized samples, obtained from surface. Tbis allows metallurgical testing to depth and definition of transitional ore types and the base of oxidation, accurately and economically with an acceptable density of samples. The accurate prediction of base of oxidation and variations in recovery with depth and ore types can be used to develop &apos;economic&apos; pit designs with zones of variable recovery. Petrological studies of leaching results and examination of mineralisation types carried out on concentrates, provide information on gold distribution and physical and chemical constraints. The examination of concentrates can be particularly useful for types of mineralisation when overall gold content is frequently at or below one pan per million. Explanation of anomalous recovery of gold grains in dense goethite and solution-robbing by carbonaceous material can be identified by use of petrological and scanning electron microscope. An understanding of the role of the host rock in leaching characteristics can also he provided by petrology where siliceous or clayey materials can require significantly different treatment.

Jan 1, 1994

By Henry Knox

AMIDST the tumult and the shouting of the times, there are perceptible certain tendencies, quiet though serious, to take stock of the situation with a view to putting our house in order, and of these none is more encouraging than the awakening, interest in the higher education, and especially in technical education. Various committees of the professional organizations have cast much light on the matter and have pointed the way to progress and reform, but their scope is necessarily restricted by the requirements of precision and any excursion beyond these bounds must be undertaken by the unfettered individual who is free to rush in where responsible committees fear to tread. A discussion of the bearing of the higher education on character scarcely lends itself to objective treatment and yet, fraught as it is with imponderables and abstractions, the theme cannot be escaped in any com-prehensive scheme of education. The question is being pressed with growing insist-ence, why these United States, relatively to Europe, are deficient in intellectual output, and the ready reply, "Because America is a new country and Americans are too intent on developing their natural resources," is too facile and too false to carry conviction.

Jan 12, 1922

By D J. Kilkenny, D A. O’Toole, P B. Hills, K L. Seah

An investigation was undertaken to critically analyse the use of fibre reinforced shotcrete (FRS) for a variety of applications in large diameter shafts. Those applications included the use of FRS with or without the addition of subsequent rock bolting in the temporary support cycle prior to the installation of a permanent lining, most likely cast in situ concrete or as the final lining medium.Numerous authors have considered the early re-entry and strength characteristics of FRS in recent years. The current study has investigated the practical application of the recommendations of many leading authors in an endeavour to establish practical and acceptable risk-assessed procedures for the use of FRS for rapid, safe, efficient and cost-effective shaft sinking.Shaft sinking is regarded as a specialist and potentially higher risk activity due to the confined work environment, exposure to ground conditions and a high degree of manual handling associated with getting materials to the sinking face. The use of robotically applied FRS as a primary lining in shaft sinking has significant safety advantages in reducing manual handing associated with mesh safety support and bolting, as well as reducing direct exposure to ground conditions.The study involved both field testing and a literature review. The study established an initial set of criteria for the use of FRS in the development of large diameter shafts and demonstrated a number of scenarios where the technique of robotically applied FRS provided significant safety and cycle time advantages. The opportunity for a fully sprayed single pass lining was also investigated as part of the project.CITATION:Hills, P B, O’Toole, D A, Kilkenny, D J and Seah, K L, 2014. Exploring the use of fibre reinforced shotcrete in large diameter shafts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 295–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

Mr. O. F. Lewis opened the meeting at 9:00 a.m. lie announced that Stan Shuhart, had the following announcement. to make: Stan. Shubart: George Delamater of Fort, Lauderdale, Florida scads greetings to his friends here at the meeting. O. F. Lewis: Thank yon, Stan. This morning we will start our meeting by turning it over to a very distinguished gentleman. I&apos;m sure all of you know him. He started his work career many, many years ago, but lie doesn&apos;t look nearly this old, and his energy belies this. From 1.910 to 1916 he was a chemist with the American Smelting & Refining Co. at. Garfield, Utah. From 16 to &apos;17 he was a broker with J. A. Hogle Company at Salt Lake. From 1917 to 1948 he was a metallurgist, ore buyer, assistant manager and later general manager of the Utah department. ASRC at Salt Lake City; and also president of the Garfield Chemical Co. Since 1951 to the present. time he has been President and General Manager of the Independent Coal & Coke Co. and Vice President of the Western Rock Bit Co. He has held many, many honorary positions; former Chairman of the Board of Regents of the University of Utah, former President of the Salt Lake Winter Sports Association, Past President. of the Community Chest there, and is presently a Director of National Coal Association, a Director of the First Security Bank of Salt Lake City, Utah, and also a Director of the Hotel Utah.

Jan 1, 1965

By B. H. Kear, H. G. F. Wilsdorf

After a few percent strain, dislocations in disordered Cu3Au are arranged in groups in ulell-defined slip planes, which contrasts with the more or less random distribution of dislocations in the corresponding ordered alloy. Unusually long and straigkt dislocation segments observed in the ordered alloy are interpreted in terms of cross slip of screw dislocations from their slip planes into cube planes. It is proposed that cross slip, and also dislocation reactions of the Lomer type, play an important role in work hardening of the ordered alloy. ACCORDING to to dislocations in the disordered lattice are only partial dislocations in the corresponding super lattice, so that in the super-lattice dislocations must occur as pairs, with each pair connected by a ribbon of antiphase boundary. Recently, striking confirmation of the theory was obtained by Marcinkowski, Brown, and Fisher3j4 in a study of dislocation configurations in thin foils of the Cu3Au alloy by transmission electron microscopy. In the present investigation, the observations made by these workers have largely been confirmed. Moreover, it has been found that dislocations in the plastically deformed ordered alloys are often unusually long and straight. This paper is mainly concerned with these new observations. A tentative explanation is offered in terms of cross slip of dislocations in the ordered alloys. PREPARATION OF SPECIMENS An alloy close to the stoichiometric composition Cu3Au was prepared by melting together high-purity copper and gold (99.995 pct) under vacuum in a graphite mold. The resulting ingot was rolled down and cut into strips 1 1/2 by 1/8 by 0.005 in. in thickness. All strips were annealed at 900°C for 3 hr and cooled to 500&apos;~. A few of the strips were quenched from ~OO&apos;C, while the remainder were slowly cooled in the temperature range 400" to 150°C at intervals of a few degrees every 24 hr to produce a high degree of order. After this annealing treatment the average grain size of the material was about 0.1 mm. Material in different states of order was obtained by reannealing fully ordered material at temperatures below the critical temperature: followed by quenching. The equilibrium degree of order attained at a particular reannealing temperature was obtained from the paper by Keating and warren.&apos; A simple hand-operated tensile jig was used to give the strips the required amounts of plastic strain. Following straining, a number of specimens were cut from each strip by means of an electrolytic cutting device.= Finally, each specimen was thinned electrolytically using the polishing procedure described by Bakish and Robertson,7 and these thin sections were examined in the Philips EM-100B electron microscope operating at 100 kv. EXPERIMENTAL OBSERVATIONS Antiphase boundaries. The average domain size in the ordered alloys was found by direct observation to be about 0.25 p. Also, it was observed that the grown-in configuration of antiphase boundaries was changed little by plastic deformation, at least up to 6 pct strain. Fig. 1 shows an electron micrograph of a thin foil of partially ordered alloy (S - 0.8) after 3 pct strain. The micrograph shows a few dislocation pairs and a somewhat crystallo-graphic network of antiphase boundaries. The normal to this foil was found by diffraction analysis to be approximately 11121, with principal directions in

Jan 1, 1962

By Phillip O. Tyree, R. A. Metz, Joseph W. Mussey

Bio-epigenetic sulphur deposits occur in Pecos, Reeves and Culberson counties of far West Texas. Sulfate reducing bacteria, utilizing hydrocarbons as energy, transformed gypsum into replacement limestone and hydrogen sulfide. Hydrogen sulfide, retained in the pores of the replacement limestone, was subsequently oxidized by highly oxygenated groundwaters, and native sulphur precipitated. West Texas sulphur was first recognized at surface exposures by William P. Blake, a geologist attached to the Captain Pope Military/ Scientific Expedition of 1854. Attempts were made in the early 1900&apos;s to mine these sulphur vent exposures by a retort method, but the ventures met with little success. In 1967, Duval discovered a large sulphur deposit near some of the old sulphur works in Culberson County. Duval also expanded reserves in a small sulphur deposit in Pecos County. The Frasch process, developed for producing sulphur from Gulf Coast salt domes, proved successful in West Texas type sulphur deposits also. However, modifications of the process were necessary to provide economical and efficient sulphur recovery from the varied ore occurrences. West Texas conditions and logistics require the ultimate in productivity to be competitive in the domestic and foreign sulphur markets. Several companies, in addition to Duval, are producing or have produced sulphur in West Texas. As of June 1, 1984, a total of 29.87 million mt (29.4 million long tons) of sulphur had been produced west of the Pecos River. Duval corporation has produced more than 88 percent of that total.

Jan 1, 1992

By Frederick C. Trutt

Research performed on arcing faults and their interactions with electrical insulating materials within coal-mine power system enclosures are described. This work was performed at The Pennsylvania State University from December 1, 1976 through August 31, 1978. The thrust of this research has been divided into several primary areas. These include the development of a theoretical procedure for computation of three-phase and line-to-line arcing fault currents as a function of time, formulation of arc and tracking models so that arc voltages and energies may be computed, development of a simulation for pressure and temperature rises when a fault interacts with an electrical insulating material within an enclosure, experimental evaluation of electrical insulating materials in terms of their tendency to support and maintain an arc as well as their potential contribution to enclosure pressure rises, and integration of the above research areas to form overall procedures for theoretical and experimental evaluation. During the course of this research, consideration has been given to the possible effects? of an internal methane-air explosion within an enclosure as well as the potential influence of utilization-voltage-level, conductor spacings, and enclosure venting. Conclusions and recommendations address potential means for protection against enclosure failure, internal design considerations, and low-power testing procedures which might be used to evaluate insulating materials to be utilized within an enclosure.

Jan 1, 1978

By Henry P. Ehrlinger, James C. Bradbury

Tripoli is a naturally occurring, very finely divided form of silica found chiefly in some midwestern and southeastern states and used commercially as fillers and abrasives. Definitions Tripoli is a microcrystalline, finely particulate, more or less friable form of silica that appears to be the product of leaching of siliceous limestone or calcareous chert. The term was originally applied to a deposit near Seneca, MO, that resembled material of that name found near Tripoli In North Africa (Hovey, 1894). The two deposits were subsequently found to have different physical characteristics -the North African tripoli, now called tripolite, is a diatomite, composed of the siliceous skeletons of microscopic marine plants called diatoms; the Missouri tripoli contains no diatom remains. The term tripoli, however, continued to be used for the Missouri material and is now applied in a general way to most silica deposits similar to it in characteristics and geologic origin. In commercial trade tripoli is commonly understood to designate material from the Missouri-Oklahoma field; silica from southern Illinois, the other major producing area, is referred to commercially as amorphous silica. Each term, however, may be used commercially for material, regardless of place of origin, that has the characteristics or uses commonly ascribed to the material from one or the other major producing area. For example, in the commodity price listings, Engineering & Mining Journal routinely lists under Tripoli, prices "f.o.b. Elco, IL" and "f.o.b. Seneca, MO, and Rogers, AR," and under Silica, amorphous, prices "f.o.b. IL," and "f.o.b. bierks, AR." Amorphous silica, the commercial designation given to southern Illinois tripoli, is, like the term tripoli, a misnomer. Mineralogically, the southern Illinois deposits are composed of microcrystalline quartz, and no amorphous material has been detected during X-ray and scanning electron microscope investigations (Leamnson, Thomas, and Ehrlinger, 1969; Thomas et al., 1970; Keller, 1978). Soft silica is another term that has been applied to Illinois and Tennessee tripoli, presumably to distinguish it from the more compact Missouri material. It has also been used in the ceramic trade to distinguish tripoli from "hard" silica, or silica flour, produced by pulverizing silica sand (Heinz, 1937). Rottenstone, produced commercially in Pennsylvania, is similar to tripoli in that a major constituent is finely particulate silica, and its uses are much the same as those of Tripoli-as abrasives and fillers. The origin of rottenstone also is similar to that of tripoli-decomposition of a siliceous sedimentary rock. The parent rock is defined as a siliceous limestone (Gary, McAfee,, and Wolf, 1972; Thrush, 1968) or as shale. Heinz (1937) quotes a brief statement describing the Pennsylvania deposits -"a black impure shaly limestone grading into black shale"-but does not identify the source of the statement. For convenience, rottenstone is included with tripoli in the reporting of production statistics in US Bureau of Mines (USBM) Minerals Yearbooks. Other materials that have been called tripoli include siliceous deposits in San Bernardino County, California (USBM Minerals Yearbooks, 1934-1941) and in Nevada (Chandler, 1960). These, however, differ in composition and/or origin from tripoli and, therefore, should not be identified by the name tripoli.

Jan 1, 1983

By C. S. Yust, J. W. Smith, J. R. Walsh, R. E. Simpson

This paper presents the results of a complete reservoir studv designed to determine a sound economic program for the conservation of oil and gas in the Pickton field, Hopkins County, Texas. The Pickton field produces from the Bacon Lime with all indications of the study being that production is predominately by dissolved-gas drive. Calculations of the total ultimate recovery to be expected under primary operations indicated only 16.7 per cent of the oil originally in place would be recovered. This unusually low recovery is due to the type of drive operating and the extremely high dissolved gas-oil ratio and shrinkage. Results are presented for six plans of returning gas to the reservoir, evaluated to determine (1) comparative recoveries and economics of (a) returning gas at a constant rate by supplementing Pickton gas with extraneous gas during the early portion of the operation, and (b) conventional gas-return operations without using extraneous gas, and (2) the optimum size of compressor plant for each type of pressure maintenance. The over-all economic program considers, for either type pressure maintenance operation. a gasoline plant to process the unusually rich casinghead gas. Since pressure maintenance will disturb equities, pooling of royalties is in the case of Pickton a prerequisite to conservation of oil by this type of operation, both from an economic and legal standpoint. In the event pooling of royalties cannot be achieved, the study considers a gasoline plant to operate under a modified primary production operation which will make the conservation of gas possible. INTRODUCTION The Pickton field, located in Hopkins County, Texas. was discovered in November, 1944. by the completion of Humble&apos;s C. D. Nichols 1, in the Bacon lime of the Lower Glen Rose formation, through perforations from 7,888 to 7.896 feet. The well initially produced 50.2 API gravity oil with a gas-oil ratio of 1,350 cubic feet per barrel. Subsurface samples of the reservoir fluid obtained soon after completion of the discovery well showed that the Pickton crude is unique in that it has an extremely high dissolved gas-oil ratio and is subject to very severe shrinkage. Calculations of the future behavior of the Pickton reservoir indicated that ultimate oil recovery by primary operations would be 3,269,000 barrels, representing only 16.7 per cent of the oil in place (19,577,000 stock-tank barrels), and that recovery could be substantially increased by returning the produced gas. The cumulative production of 1,382,694 barrels on November 1: 1947, amounted to 42.3 per cent of the estimated ultimate oil recovery from primary operations. The purpose of this study is to determine and evaluate the optimum program for conservation of oil and gas in the Pick-ton field, including the desirability of conducting gas-return operations and of installing a gasoline plant. LOCATION AND DESCRIPTION Pickton Field, The Pickton field, as shown in Fig. 1, is located in southwest Hopkins County, Texas, 12.5 miles southwest of the New Hope field, 2.7 miles northeast of the Coke field, 16 miles southwest of Sulphur Springs, and 8 miles northwest of Winnsboro, Texas.

Jan 1, 1949

By C. S. Yust, J. W. Smith, J. R. Walsh, R. E. Simpson

This paper presents the results of a complete reservoir studv designed to determine a sound economic program for the conservation of oil and gas in the Pickton field, Hopkins County, Texas. The Pickton field produces from the Bacon Lime with all indications of the study being that production is predominately by dissolved-gas drive. Calculations of the total ultimate recovery to be expected under primary operations indicated only 16.7 per cent of the oil originally in place would be recovered. This unusually low recovery is due to the type of drive operating and the extremely high dissolved gas-oil ratio and shrinkage. Results are presented for six plans of returning gas to the reservoir, evaluated to determine (1) comparative recoveries and economics of (a) returning gas at a constant rate by supplementing Pickton gas with extraneous gas during the early portion of the operation, and (b) conventional gas-return operations without using extraneous gas, and (2) the optimum size of compressor plant for each type of pressure maintenance. The over-all economic program considers, for either type pressure maintenance operation. a gasoline plant to process the unusually rich casinghead gas. Since pressure maintenance will disturb equities, pooling of royalties is in the case of Pickton a prerequisite to conservation of oil by this type of operation, both from an economic and legal standpoint. In the event pooling of royalties cannot be achieved, the study considers a gasoline plant to operate under a modified primary production operation which will make the conservation of gas possible. INTRODUCTION The Pickton field, located in Hopkins County, Texas. was discovered in November, 1944. by the completion of Humble&apos;s C. D. Nichols 1, in the Bacon lime of the Lower Glen Rose formation, through perforations from 7,888 to 7.896 feet. The well initially produced 50.2 API gravity oil with a gas-oil ratio of 1,350 cubic feet per barrel. Subsurface samples of the reservoir fluid obtained soon after completion of the discovery well showed that the Pickton crude is unique in that it has an extremely high dissolved gas-oil ratio and is subject to very severe shrinkage. Calculations of the future behavior of the Pickton reservoir indicated that ultimate oil recovery by primary operations would be 3,269,000 barrels, representing only 16.7 per cent of the oil in place (19,577,000 stock-tank barrels), and that recovery could be substantially increased by returning the produced gas. The cumulative production of 1,382,694 barrels on November 1: 1947, amounted to 42.3 per cent of the estimated ultimate oil recovery from primary operations. The purpose of this study is to determine and evaluate the optimum program for conservation of oil and gas in the Pick-ton field, including the desirability of conducting gas-return operations and of installing a gasoline plant. LOCATION AND DESCRIPTION Pickton Field, The Pickton field, as shown in Fig. 1, is located in southwest Hopkins County, Texas, 12.5 miles southwest of the New Hope field, 2.7 miles northeast of the Coke field, 16 miles southwest of Sulphur Springs, and 8 miles northwest of Winnsboro, Texas.

Jan 1, 1949

By H. Walqui, A. Buendía

The Toquepala concentrator expansion project incremented the capacity of the existing concentrator by 15,000 Metric tons per day (t/d), from 45,000 to 60,000 t/d. The plant is located in southern Peru,1,200 km southeast of Lima. The implementation plan for the expansion project was based upon an engineering and procurement contract, and a construction contract. The overall Project Management was by Southern Peru Copper Corporation (SPCC). The expansion followed a very aggressive schedule that considered a construction period of only ten months, with minimum interference to the existing facilities. Major equipment was purchased during basic engineering. This paper details the design, construction, and commissioning of the 6.4 m diameter by 10.2 m long ball mill, and the performance of the milling circuit during the first two months of operation.

Jan 1, 2003