Search Documents

ARTHUR H. STORRS, Scranton, Pa.-I would like to ask whether this same process is applicable to bituminous coal? FELLS A. VOGEL, New York, N. Y.-This Dutch process is applicable to bituminous or any other kind of coal. The Berwind Fuel Co. has had a plant in operation, in Superior, Wis., for about 2 years, using the Dutch process, and it has made a very satisfactory briquette, using Pocahontas coal. There is just one item in Mr. Frey's paper I would like to discuss; that is, the matter of cost. Mr. Frey figures a total cost of $3.35, based on the use of 7 per cent. of oil. Of course, the price of oil has advanced seriously within the last year or two, and any possible reduction in the percentage of oil required in the manufacture of briquettes is very important. I believe that Mr. Frey will agree that very good briquettes can be made with considerably less than 7 per cent. of oil; in fact, actual experience has shown that it can be clone with less than 5 per cent. The only possible effects of a low percentage of oil, particularly in anthracite briquettes, are that the briquette might not burn so freely, and that it might not be quite so hard. Briquettes made by the Lehigh Coal & Navigation Co., using 7 per cent. of binder, are extremely tough. Those briquettes have been handled in one of the local yards in Brooklyn, chuting them from railroad cars into boats and digging them out by grab buckets, and the losses average less than 2 per cent. This compares very favorably with domestic anthracite coal, with which the losses from breakage amount to between 7 and 10 per cent.

Jan 4, 1918

By T. B. Massalski, Horace Pops

The occurrence and the temperature dependence of the athermal martensitic transformation in bcc Cu-Zn ß-phase alloys have been studied by cold-state microscopy, differential thermal analysis, and electrical -resistivity measurements. CinenzatograpJzic studies have shown that in the majority of alloys the transformation occurs in two stages. A thermoelastic phase, having a 'needlelike" uppearance, forms initially at the MS temperature and grows relatively slowly, chiefly in the edge (lengthwise) direction. With further cooling, an additional martensitic phase forms in rapid bursts at a lower temperature, MB, Both martensitic phases appear to have the same cry stallographic habit hut their modes of formation and growth are different. For the composition range studied, between 38.55 and 41.49 wt pct Zn, the habit planes determined are close to the (2.17 ,12) plane of the matrix, in general agreement with the prediction of the phenomenological theory of martensite formation. Thermal cycling through the MB temperature produces permanent plastic deformation in the 0 matrix and gradutally eliminates the typical burst phenomena. Thermal cycling only through the MS temperature produces no noticeable deformation effects. THE bcc Cu-Zn ß-phase alloys tend to become unstable at low temperatures and undergo a martensitic transformation,'-3 but the details of the transformation have not been completely determined. Following earlier metal log raphic and X-ray work1 Tichener and ever' determined by means of electrical-resistivity measurements the temperature range of the martensite transformation during continuous cooling. The transformation temperature was found to decrease with increasing zinc content, becoming about -130°C for an alloy containing 40.04 wt pct Zn. Hull and Garwood3 made a metallo-graphic study of Cu-Zn 0 brasses at temperatures down to -160°C, and determined the habit plane of the transformation product for an alloy containing 38.88 wt pct Zn. No metallographic studies below liquid-nitrogen temperatures have been reported. The martensitic transformation in ß-brass alloys can also be induced by deformation.1,4 The MD temperature corresponding to the appearance of the strain-induced martensite is some 300°C higher than that observed without strain, and hence the transformation can be strain-induced in alloys containing a higher percentage of zinc. Massalski and Barrett4 found that alloys containing as much as 51.89 wt pct Zn could be transformed into a faulted hcp structure by cold working at liquid-helium temperature. Because the details of the MS temperature and morphology reported in the literature are somewhat incomplete, a further study has been made of some of the above features. A design of a cryogenic stage for optical metallography5 has permitted the examination of specimens at temperatures down to 4.2oK, and the use of a cinecamera has permitted a study of the morphology on cooling and heating. The particular aim of the present work was to examine the transformation temperatures, the habit planes, and the growth morphology over a wide composition range in the ß-phase field. The effect of thermal cycling upon the subsequent transformation was also examined.

Jan 1, 1964

By C. Vasilescu

Phytotechnologies use plants to remediate various media impacted with different types of contaminants. These technologies can be implemented either in situ or ex situ. The affected media in which phytotechnologies can be applied include soil, sediments, groundwater and surface water. They are best applied at sites with shallow contamination of organic, nutrient, or metal pollutants that are amenable to one of five treatment options: phytoextraction, phytotrans-formation, rhizosphere, bioremediation, phyto-stabilization or rhizofiltration. Phytoremediation can be used along or, in some cases, in place of mechanical cleanup methods. Phytoremediation can be used to clean up metals, pesticides, solvents, explosives, crude oil, polycyclic aromatic hydrocarbons and landfill leachates.

Jan 1, 2006

By Rao Pothini

Measurement of pressure distribution under the base plate of the Hemscheidt 2-leg 800-ton shield was performed underground for two shifts using 12 pressure cells installed in two rows, one each under each split base plate. Pressure distribution was uneven depending on contact condition. In general the highest base pressure occurred at 1/3 of the base plate contact length from the rear edge. The resultant was near vertical, and the pressure under the tail side split base plate was always higher than the head side. For comparison, pressure distribution on the canopy and under the base plate was also measured under controlled conditions at the USBM's Mine Simulator Testing Facilities in Pittsburgh, PA. A total of 45 tests were conducted under several simulated contact conditions. The results showed that the actual contact area is highly dependent on the compliance of the immediate roof and floor due to the sloped canopy tip and a base lifting device under the base tip. The loading distribution tends to change in magnitude and profile as the leg pressure increases. The base lifting device exaggerates the high toe loading on the base plate characteristics of this type of shield support. This paper describes in detail the testing methods, data analysis results obtained, and recommended changes.

Jan 1, 1992

By J. J. Arps

This paper reviews the methods currently in use for estimating primary oil reserves and discusses the principles on which these methods are based. Particular emphasis is placed on how these methods change with the type of information available during the life cycle of an oil property. This paper contains various novel estimating methods and shortcuts heretofore unpublished. INTRODUCTION Estimating oil reserves is one of the most important phases of the work of a petroleum engineer since the solutions to the problems he deals with usually depend on a comparison of the estimated cost in terms of dollars, with the anticipated result in terms of barrels of oil. His recommendations to management regarding the best course of action are therefore normally based on the most favorable balance between these two. Specific engineering problems which require such a knowledge of recoverable oil reserves and a projection of future rates are: [a.] the exploitation and development of an oil reservoir; [b.] the construction of gasoline plants, pipelines and refineries; [c.] the division of ownership in unitized projects; [d.] the price to be paid in case of a sale or purchase of an oil property, and the magnitude of the loan which it will support; [e.] the proper depreciation rate for the investment in oil properties; and [f.] evaluation of the results of an exploration program. This discussion will be confined to the various methods and tools which are currently in use for estimating oil reserves to be obtained during the primary phase of an oil-producing reservoir and for a projection of the future production rates. Reserves which may be obtained by secondary recovery methods or fluid injection programs and gas and gas condensate reserves will not be discussed in this paper. Unfortunately, reliable oil reserve figures are most urgently needed during the early stages when only a minimum amount of information is available. Management's interest in the oil recovery from a property—aside from its use for accounting purposes—usually declines when the property approaches its economic limit, just at the time when the reliability of the estimates is at its best. To illustrate this general idea a chart is presented (Fig. 1) showing the three periods in the life of an imaginary oil property. Time is shown on the horizontal axis, while the cumulative production and estimated ultimate recovery are plotted vertically. No particular units are used and this schematical chart is not to scale. During the first period, before any wells are drilled on a property, any estimates will of necessity be of a very general nature, based on experience from similar pools or wells in the same area, and usually expressed in barrels per acre. This will

Jan 1, 1957

By D. L. Luffel

This paper presents two main developments: (1) a short, constantly accelerated centrifuge method of measuring drainage capillary pressure properties of cores, and (2) a new analytic method of treatment of centrifuge measurements to obtain saturation-capillary pressure relations. Toward the first objective, a clever experimental method is presented which is certainly more rapid than previous centrifuge methods. Toward the second objective, a new analytic method is derived to eliminate the approximate method of Hassler and runner. The derivation of this new analytic method, however, appears to be in error. The new analytic solution is developed as Eq. 5 in Appendix A. At the beginning of this derivation, the average wetting phase saturation of a core is expressed as, where is the centrifuge angular velocity. Eq. D1.2 makes explicit the dependence of S and S upon The second equation shown in Appendix A expresses the relation between the three variables Since for a given porous medium the saturation is uniquely related to capillary pressure, the functional dependence of S upon P is trivial, i.e., Pc.ri does not actually appear. Thus, the function 5 (r, ) may be expressed as a new function, S*, of PC, , alone The author transforms the variable of integration in Eq. Dl through use of Eq. D2 and writes

Jan 1, 1965

By Barro L

There is currently a world wide interest in coal-oil technology as the search continues for alternative energy sources to reduce the consumption of petroleum crude. An important aspect of this coal-oil technology study is to obtain information on the flow properties of coal-oil slurries. While some work has been reported on the flow behaviour of black coal-oil suspensions, very little work on brown coal-oil suspensions has been reported. In this paper flow charac- teristics of brown coal-oil suspensions for various coal concentration and temperatures have been presented. A Capillary rheometer, designed to handle settling suspension, has been used for deter- mining rheological properties. Brown coal of 0 0725 mm average particle diameter has been used in this work. The oil was a coal derived product having a boiling point range of 234¦- 319¦C, Apparent viscosity of all suspensions was found to increase on storage due to ageing. Ageing might have occurred due to physico- chemical interactions between coal and oil. Flow behaviour of some suspensions changed from Newtonian to non-Newtonian on storage.

Jan 1, 1980

By D. J. Carney, E. Van Meter, J. J. Oravec

A study was made of combustion-air temperatures and factors affecting air temperatures in the open-hearth regenerative systems. Air-temperature surveys in the regenerative system revealed marked thermal gradients in the air above the checkers. The design of the fantail-uptake region plays a prominent part in increasing the heat recovery of the regenerative system. THE efficiency of the open-hearth regenerative system is one of the most important factors affecting open-hearth performance. Until recently, this factor has not received the attention in the literature given to many other items affecting performance, such as the type of charge, speed of charging, and the mechanical equipment of the open hearth. J. S. Marsh' emphasized the importance of the flame temperature and its dependence upon the combustion-air temperature. By means of measured air temperatures in open-hearth furnaces, data were presented which showed a remarkable degree of correlation between production rate and combustion-air temperature. This correlation was extremely good in view of the numerous factors, other than air temperature, which affect open-hearth production rates. In Marsh's work, a 100°F increase in air temperature reduced the heat time by approximately 45 min. Realizing the importance of combustion-air temperature, it is desirable to know which factors control the regenerative efficiency of the open-hearth furnace. B. M. Larsen recently discussed this subject.' The present paper illustrates a few of the more important items that affect regenerative efficiency and combustion-air temperature. In the latter part of 1951, a study of open-hearth combustion-air temperatures was begun at the South Works of the United States Steel Corp. In the initial work at open-hearth shop X, which produces low carbon steel products, temperatures were measured in the uptake in a manner similar to that used by Marsh' and the results obtained were very similar to the Bethlehem data. When it was decided to expand the study of combustion-air temperatures, open-hearth shop Y was selected because of the greater variety of furnace-design features, types of steel produced, and firing rates used. With the use of aspirating thermocouples, continuous gas analyzers, thermocouple and optical pyrometers, a study was made of: 1—effect of combustion-air temperature on open-hearth production rate, 2—thermal gradients present in various zones of the regenerative system, 3—effect of furnace-design variations on air temperature and heat recovery, 4-—effect of furnace-operating variables on heat recovery, and 5—variation in heat recovery with furnace age during the normal furnace campaign. Data collected on individual heats at 15 min intervals included air-flow rate, firing rate, checker temperature, combustion-air temperature, and furnace pressure. These data were collected on approximately 230 heats of steel. In addition, information was obtained at random on air infiltration and combustion-gas compositions. The data gathered have shown the desirability of closer control of open-hearth firing practices, a need for reducing air infiltration in the uptake zones, and a need for further study of design of checkers and of uptake-fantail areas. Equipment Air is practically a nonradiating medium. Consequently, in the measurement of air temperatures, the principle of heat conduction must be used rather than heat radiation. For this reason, aspirating-type thermocouple pyrometers normally are used to measure air temperatures. With these devices, air

Jan 1, 1956

By Galen Clevenger

THE losses of gold and silver occurring during the conversion of the precipitate, resulting from the cyanide process, into bullion may occur in two ways: first, there may be mechanical losses during the handling of the precipitate up to the time that it is charged into the melting furnace; and second, there may be losses after the precipitate reaches the melting furnace. Much of the loss during the handling of the pre-cipitate can be eliminated, and in fact, in modern plants this loss is known to be very small; particularly since preliminary acid treatment of the precipitate with the attendant extra operations has been abandoned in all but certain plants where gold predominates and this extra step is still deemed necessary. The losses in the melting furnace are from dusting and volatilization; losses in the furnace bottom and linings; floor sweepings; and slag and matte. The gold and silver in the: products which do not: go out of the flue are readily recoverable by standard methods, and while there may be considerable gold and silver tied up at times, the ultimate loss with careful "work should be small. The losses resulting from volatilization and dusting in connection with the melting of the silver slime from copper refineries have been determined by standard methods, and the possible recovery: definitely estab-lished through the installation and operation of electro-static precipitation units. This subject has not been thoroughly investigated in connection with the melting of`. cyanide precipitate; at least, there are no published accounts of such tests. Experiments have been made in the past to determine melting losses by weighing and assaying the precipitate, but this method gives results which are uncertain on account of the difficulty of accurately sampling and assaying cyanide precipitate. Attempts to ascertain these losses by bubbling a measured sample of the gas through cyanide solution or, other absorbent have likewise failed to give depend-able results.

Jan 1, 1922

By R. H. Hopkins, R. W. Kraft

X-ray and metallographic analysis reveal that the preferred cryslallograPhic relationships in direc-tionally solid~fied Pb-Sn eutectic specimens can be stated: interface growth direction, Experiments in which tin single-crystal seeds were used to nucleate the eutectic demonstrate that the normal lamellar structure observed at steady state can be forced to break down initially to a semide-generate structure when the crystallograPhic direction of the tin seed does not lie within the preferred eutectic interface plane. A normal structure eventually develops by preferred grain growth. X-ray topo-graphs and rocking curves substantiate that the perfection of eutectic samples increases as growth proceeds until steady-state conditions prevail. RECENT years have seen substantial progress made in the understanding of eutectic solidification through both intensive theoretical1'' and experimental investigations (see Ref. 7 for a review and extensive bibliography of both aspects). Several important observations concerning the nucleation and growth aspects of binary eutectic solidification have been brought to light. Briefly some of these include the nonrecipro-cal nucleation of one phase upon another,'j9 the tendency for a specific low-index direction of one or both phases of the eutectic to be aligned in the growth direction during unidirectional solidification,'0711 and the production of lamellar microstructures having a preferred interface plane between "11-13 phases. Questions quite naturally arise as to the mechanism by which preferred grain growth evolves during eutectic solidification and what relationships (if any) connect the initial nucleation of one phase upon another with the preferred growth directions and interface planes observed after a few centimeters of growth in many systems. This study was initiated in an attempt to answer these questions. An experiment was devised in which both the nucleation and growth steps in the crystallization of a binary eutectic, Pb-Sn, could be correlated with subsequently developed eutectic morphology and crystallography. This was accomplished by nucleating the eutectic upon a tin single crystal seed and then causing the eutectic to grow from the seed by directional freezing. The morphology of the structures produced in this manner was then monitored metallographically and the orientation relationships and substructural perfection determined by X-ray analysis. The information thus ob- tained was correlated to the growth history of the samples. EXPERIMENTAL DETAILS The eutectic of composition 38.1 wt pct Pb and 61.9 wt pct sn14 was prepared by accurately weighing lead and tin of 99.999+ (from ASARCO and Lytess Metals and Chemicals, respectively), melting in a clean Pyrex beaker under an argon blanket, and casting into the proper crucible for resolidification as described below. Tin seeds were grown by the method of ~halmers," saw-cut, oriented by the Laue method, and soldered to the pull rod of the Czochralski puller. All seeds were given a final electropolishing (to assure the removal of any deformed material from the cutting operation) and acetone degreasing immediately prior to the nucleation experiment in which they were to be used. Eutectic samples were unidirectionally solidified in a horizontal graphite boat1' or by pulling from the melt16 with tin (or graphite) seeds. A flowing argon atmosphere was employed in all experiments and growth rates and temperature gradients, constant for a given run, varied from 2 to 4 cm per hr and 8" to 15°C per cm over the course of all the experi-

Jan 1, 1969

By Edward Halse

The occasional occurrence in metalliferous veins of rounded fragments of rock, matrix or ore, lying loose, embedded in clay, or enclosed in some kind of cement, may be attributed to four causes:— I. They have been washed in from the surface, or from an upper portion of the vein.. II. They are of concretionary origin. III. They have been produced by movements in the country-rock or in the walls of the vein. TV. They have been formed in situ, by the upward, downward or lateral flow of water in the vein itself. In this paper the word " conglomerate " is confined to a rock composed of rounded fragments or pebbles cemented together, as distinguished from a " breccia," in which the rock-fragments are angular. * I. Boulders and Pebbles which have been Washed in from the Surface, or from an Upper Portion of the Vein. In this type it is presupposed that the vein at one time communicated by a fissure or open space with the surface, or with the upper portion from whence the fragments have been washed. One well-authenticated occurrence was described long ago by Fournet. Owing, no doubt, to later dislocations in the lode, pebbles from an old alluvium and sands containing titaniferous iron, as well as fragments of wood, were found in a vein at Huelgoet, in France. " Toutes les parties tendres du filon de Pranal ou ces phenome'nes sont les plus prononces ont 6th excaves jusqu'a d'aasez grandes profondeurs par I' impetuosite des torrents, qui out depose la matiere alluviale.'"

Jan 1, 1906

By E. A. Gulbransen, W. S. Wysong

THE behavior of tungsten and its surface oxides in oxidizing and reducing atmospheres and in high vacua at elevated temperatures is a question of considerable technical importance. The use of tungsten as a metal or as an important component in alloys in high temperature oxidizing atmospheres has been limited because of the unprotective nature of its oxide film and the volatility of its oxide. This paper will present results of a microbalance study1,2 of the following problems: (I) the oxidation behavior in the temperature range of 25 to 550°C (2) the reduction with pure hydrogen of thin oxide films formed on tungsten, and (3) the volatility of thin oxide films on tungsten. Tungsten is an interesting metal to study for the following reasons: (1) although the oxide to metal volume ratio is greater than one, the oxide is not considered protective, (2) the metal readily oxidizes at temperatures from 300° to 550°C (3) the oxides W02 and WO3 are reduced at temperatures as low as 500°C. by hydrogen, and (4) the oxide W02 is volatile at temperatures from 800 to 1100°C. LITERATURE The oxidation of tungsten in its thin film range has not been studied critically. In the thick film range Dunn3 has made the only systematic study. He found the oxidation rate to obey the parabolic rate law in the temperature range of 700 to 900°C. The temperature variation of the oxidation rate constant was found to follow an exponential law of the Arrhenius type. An inflection was noticed in the temperature plot of the rate law constant at 850 to 900°C. This was attributed to a phase change in the oxides. Scheil4 has studied the oxidation rate at 500 and 700°C over long periods of time and found a linear rate law. This result was interpreted as evidence for the presence of a nonprotective film. Pilling and Bedworth5 analyses of the oxide volume to metal volume ratio would indicate that a compact protective film should form. McAdam and Geil6 have studied the oxidation of tungsten in the thin film range using the interference color method. A parabolic rate law was found. Their curves showed that tungsten oxidizes faster than nickel but more slowly than iron. The lattice structures found in the oxidation of tungsten surfaces have been studied by Hickman and Gulbransen.7 They have reported that W03 is the stable oxide in contact with the metallic substrate up to approximately 600°C while W02 forms first at 700°C. Hägg and Magneli8 have recently reported a study of the lattice structures observed in the tungsten oxides using the X-ray diffraction method. In addition to an a-phase W03 and a d-phase W02, they reported the existence of two new phases. A ß' phase, homogeneous between

Jan 1, 1947

By Charles L. Kimbell

Annual global steel industry investment is partly mirrored in the data for selected market economy countries that appear in table 13 for 1988-90. No reasonably comprehensive 1991 data were available for inclusion in this study, and the partial reporting available was so incomplete that it was impossible to demonstrate whether the level advanced or declined from the 1990 level of nearly $15.5 billion. Moreover, with the radical changes that are now being effected in the steel industries of the states that were the U.S.S.R. and its CMEA partners, it is most regrettable that comprehensive and comparable data, both current and historic, on investment in this area are not available. Updated information on market economy country petroleum industry capital and exploration expenditures by geographic area has been included in table 14, and it is evident that there was a substantial upturn in investment in 1991. The level of almost $74.5 billion was 14.5 % above the 1990 level and included gains in every topical category and geographic area. The source of information for this table has been changed to the Oil and Gas Journal Database from the previously used Chase-Manhattan Bank study of Capital Investments of the World Petroleum Industry, which has been discontinued. Because of this source change, it has been necessary to modify the structure of the table somewhat, but its total scope of coverage is regarded as basically unchanged. It should be noted that the grand total, as well as some of the detail appearing for 1987, corresponds precisely with those in the previous source.

Jan 1, 1993

By Raja V. Ramani

The potential usefulness of reclaimed surface-mined land has received much attention recently. In an effort to develop a procedure for evaluating postmining land use potentials, specific mines in various regions of the U.S. were studied to determine the extent of current mined-land planning and to discover characteristics that are regional in nature. As part of this investigation, the Chinook Mine-West Field, located in western Indiana, has been studied. The Chinook Mine is presently operated by AMAX Coal Company and has been in continuous operation since 1928 under various ownership. The status of current reclamation and land use planning was reviewed. In addition, site planning principles were applied to the active mine area. This application included formation of a data base and development of postmining land use plan alternatives. Key factors affecting site potential realization for midwestern area mines have been identified along with suggestions for applying land use planning processes to mined-land planning.

Jan 1, 1983

The Earth Moving Equipment Safety Round Table (EMESRT) was established by mining companies in 2006 to influence manufacturer's equipment design through a process of engagement. 2010 EMESRT member companies include Anglo American, Barrick, BHP Billiton, Centennial Coal, Collahausi, Newcrest, Newmont, Rio Tinto, Vale and Xstrata.Driven by a persistent need for retrofits to new equipment, such as haul trucks, EMESRT initially engaged with Surface Equipment Manufacturers including Caterpillar, Komatsu, Leibherr, Hitachi, Le Tourneau and Terex. These OEMs responded positively to the EMESRT initiative, welcoming the opportunity for dialogue with an aligned industry regarding human factors issues related to equipment design, rather than needing to respond to the disparate range of demands for design modifications previously received from individual customers. This engagement process is about making global sustained changes within the OEM organisations and within the mining companies. It is a very international exercise. For example, over two weeks in September 2010, a total of 21 different miners from ten different companies travelled from Australia, South Africa, Canada, Brazil, Singapore and the United States to engage with OEM counterparts who assembled from the United States, Japan, France, Sweden, Finland and Germany. EMESRT Surface Group representatives completed a whirlwind tour of the major North American manufacturers of mining equipment. Starting in Dallas (Atlas Copco, LeTourneau), this tour passed through Gainesville (Sandvik), Newport News (Liebherr), Guelph - Ontario (Hitachi) and Milwaukee (P&H Mining/Joy Global; Bucyrus), before winding up in Peoria, Illinois (Komatsu, Caterpillar). Over nine meetings, this group engaged with 129 individuals from nine OEMs. The EMESRT group welcomed miners from four non-member companies to come along for the meetings. These companies are Syncrude Canada Ltd, the Kearl Oil Sands Project - Imperial Oil (ESSO), Suncor Energy Ltd and Teck Resources Ltd.Other mining industry sectors have now expanded the EMESRT scope from surface mining to include exploration and underground mining equipment. In 2009, EMESRT was organised into four Technical Groups, consisting of EMESRT member company representatives, to focus on engagement with OEMs of surface, underground coal and soft rock, underground hard rock, and exploration drilling equipment. An advisory group has been formed to coordinate activities between all workgroups and provide strategic direction and cohesion between all activities. The Minerals Industry Safety and Health Centre (UQ-SMI) facilitates and coordinates all EMESRT activities on behalf of member companies. Building on successes with individual Surface Mining OEMs, EMESRT now aims to help OEMs in their transition to a sustainable design process that will incorporate and address specific design philosophies at the concept phase of design, so that significant improvements can be made up front for little cost within the overall budget. EMESRT members plan to educate all stakeholders, internally, within their own companies, and externally, by addressing industry associations, regulators and other end users about new ways of evaluating equipment design based on EMESRT purchasing specifications. This presentation will outline the EMESRT approach and report on progress in 2010.

Dec 6, 2010

R. W. Balluffi (Atomic Energy Div., Sylvania Electric Products Inc., Bayside, N. Y.)—Since porosity is known to form in the copper side of Cu-Ni couples during diffusion24,25 it is of importance to consider this factor in interpreting the large variations of chemical diffusivity with copper concentration reported for this system. The presence of porosity may affect the measurement of D in two ways: 1—density changes in the couple invalidate the usual solutions of the diffusion equation, and 2—the pores may act as short-circuiting paths when transport through the vapor or along internal surfaces is appreciable or else as open circuits when these effects are small. The error produced by the first effect may be estimated by a graphical analysis. Fig. 8 shows the porosity generated in the copper side of the Kirkendall interface of a pure nickel vs pure copper couple after diffusion for 350 hr at 1040°C in hydrogen. In Fig. 9 the actual diffusion curve which would be obtained by the usual slicing technique is shown as a solid line drawn to the same scale (from the data of da Silva and Mehl"). The amounts of porosity (obtained by lineal analysis) and of nickel are graphically represented by the hatched areas. The standard solutions of the diffusion equation are valid only when all volume elements of unit length and unit cross section contain equal numbers of atoms." It is possible to correct the experimental curve to satisfy this condition by shrinking the couple in the direction of diffusion in such a way as to eliminate the porosity.* The corrected diffusion curve obtained after

Jan 1, 1954

Covering resources, production, uses, defense impact, and future outlook of nickle, Mining Engineering presents the third in a series of articles on strategic minerals. Preceding it are "Cobalt" in January and "Sulphur" in May.

Jan 8, 1951

By Eric J. Beckman

Recovery of metals from dilute solution, whether the matrix is solid, or liquid, remains a considerable technical and financial challenge. Methods currently exist whereby metals can be extracted from either type of matrix, yet these methods consume significant quantities of reagents and can also generate multiple waste ,streams in the process. Technology developed in our lab allows efficient application of environmentally-benign CO2 to a number of separation problems involving metals. For example, we have employed biphasic mixtures of C02 and water as a green acid leach medium. Metals have been extracted from a steelmaking process residue and then recovered as metal carbonates through depressurization. In this process, metals are extracted and recovered without the use of reagents other than CO2 and water, and CO2 is sequestered as a solid. In addition, through synthesis of Cal-miscible phase transfer agents, we have shown that CO2 can replace the organic solvent currently used in refining of precious metals, The sensitivity to pressure of phase behavior in a CO2-mixture may allow significant streamlining of the process as well. Finally, CO2 soluble chelating agents have been used to extract toxic metals from acidic effluent such as that found in plating facilities.

Jan 1, 1999

By V. A. Marple, K. L. Rubow, B. A. Olson

"A virtual impactor personal aerosol sampler (VIPAS) bas been developed for use in diesel-equipped mines to collect size-separated samples or diesel exhaust and mine dust particles in the respirable size range. This sampler consists or three stages: a 10-mm cyclone, a 0.8- µm cutpoint virtual impactor and two filter cassettes. The large non-respirable particles are removed in a 10-mm cyclone. The respirable particles from the cyclone pass through a 0.8- µm cutpoint virtual impactor with the particles larger than and smaller than 0.8 JI.ID (mine dust and diesel exhaust particles, respectively) collected on two 37-mm filter cassettes. The sampling How rate is 2 L/min so as to be compatible with the standard respirable dust sampler and personal sampling pumps. INTRODUCTIONThe mining industry has been increasing its use of diesel-powered equipment in underground mines, especially in coal mines. With this increased usage has come an increased concern regarding the health effects associated with inhaling diesel exhaust particles since they are in the respirable particulate size range. A Mine Safety and Health Administration (MSHA) advisory committee directed MSHA to develop a sampling protocol for diesel exhaust particles to assess worker exposure (MSHA, 1988). In addition, the National Institute for Occupational Safety and Health (NIOSH) has recommended that ""whole diesel exhaust be regarded as a potential occupational carcinogen as defined in the Cancer Policy of Occupational Safety and Health Administration"" (NIOSH, 1988).Past work, with cascade impactors in both the laboratory and in underground coal mine studies, has shown that the diesel exhaust particles are primarily in the less than 0.8 µm aerodynamic diameter size range whereas the coal dust particles are primarily greater than 0.8 µm (Marple et al., 1986; Cantrell, 1987; Rubow and Marple, 1988; Rubow et al., 1990a, b; Cantrell and Rubow, 1991). This work has been jointly performed by the University of Minnesota and Bureau of Mines researchers over the last 8 years. Typical particle size distributions for a diesel-equipped coal mine and an all electric coal mine are shown in Figure l. Note that the particles in the < 0.8-µ.m mode are the diesel exhaust particles (seen only in diesel-powered mines) and the particles in the > 0.8-µ.m mode are coal particles (seen in both the electric-powered and diesel-powered coal mines). Chemical mass balance analysis was also performed on these two size fractions to determine the degree of particle cross-contamination in the two modes. This analysis showed less than 10% cross-contamination, i.e., in coal mines Jess than 10% of the diesel exhaust particulate was collected in the coarse fraction and Jess than 10% of the mine dust was collected in the fine fraction (Cantrell, 1987; Rubow et al., 1990a)."

Dec 1, 1996

By William E. Newman

When Hugh Lee Pattinson discovered, in 1829, that the crystals formed during the slow cooling of molten lead were poorer, and the remaining liquid richer in silver, than the original lead, an important step was made in the metallurgy of this metal. Being the first process applicable to the desilverization of low-grade lead bullion, it soon found its way into all European countries having such a product to treat, thereby effecting the saving of many ounces of silver annually which previously had been thrown away. The old hand process was expensive, as viewed from the standpoint of more modern methods; the labor was great and the tonnage was small, but on the other hand the results were fairly satisfactory. This process flourished for some time after the introduction of the cheaper Parkes process in 1852 and it is still in use in a few European smelteries. Only one notable improvement was made on the original process, that of Luce and Rozan at Marseilles, France. It consisted in the application of steam for stirring and the tapping of one-third of the liquid lead, through perforated plates covering the tap holes flush with the bottom of the kettle, thus leaving two-thirds in the form of crystals in the original kettle. This modification considerably lowered the operating costs as it permitted of much larger kettles, an increased tonnage and eliminated much of the slow, hard labor of the hand process. The Luce and Rozan process has persisted in its original form to the present day. Stephen Tredinnick, English born, spent most of his years around the Luce and Rozan plants at Marseilles and elsewhere in Europe, coming later to Eureka, Nev., in 1878, to operate the Luce and Rozan plant at that point. Mr. Tredinnick was a competent Luce and Rozan operator and being devoted to the process he firmly believed that with modifications the costs could be so lowered as eventually to supplant the Parkes process. Out of many schemes he decided that this could be accomplished by placing the Luce and Rozan kettles upon hydraulic rams so that each

Jan 1, 1918