Search Documents

By A. U. Seybolt

DURING the course of experiments involving oxygen equilibrations with a high-purity Pd-5 at. pct Rh alloy, the appearance of a subscale was noted. Most of the heat treatments in a pure oxygen atmosphere were performed at 900°C. The presence of the subscale was noted when the oxygen partial pressure was in excess of approximately 95 mm, up to 1 atm, the highest pressure used. According to available thermodynamic information' on the free energy of formation of Rh2O3 (the only reliably reported solid oxide of rhodium), this oxide should not be stable under these conditions, nor, of course, any oxide of palladium. Extraction of the subscale from the matrix was affected by treatment with aqua regia, and the resulting X-ray diffraction powder pattern is shown in Table I. This pattern is not that of Rh2O3, nor that of any known rhodium or palladium oxide. It can be indexed on a hexagonal lattice with a. = 5.22Å and co = 6.0Å. In addition to this unknown material, there was a weak Rh2O3 pattern. An X-ray fluorescence analysis of the powder gave 3214 palladium counts per sec and 5381 rhodium counts per sec, thus indicating the likelihood of a double oxide of palladium and rhodium. In view of the fact that the above result was obtained on a single sample, it is perhaps best not to insist upon the above ratio of about 0.6, but possibly to tentatively assume 0.5 or 1/1. The small amount of Rh2O3 in the X-ray pattern might have occurred on cooling, and it seems possible that the double oxide, below some temperature level, is not as stable as Rh2O3. To examine this point, some of the extracted double oxide was heated on a sheet of pure palladium in air at 900°C, and allowed to furnace-cool over a period of several hours. The X-ray diffraction pattern of the powder showed approximately the same intensity of Rh2O3 and the "hexagonal" oxide as before, but, in addition, a rather faint pattern of another crystalline species made its appearance. This finding again suggests partial transformation of the major (double) oxide to other oxides on cooling from 900°C. Application of the phase rule shows that only one equilibrium oxide (subscale) could have been present at temperature. Vacuum-fusion, oxygen analysis of the extracted subscale showed 7.7 ± 0.7 pct O. Combining this information with that of the X-ray fluorescence analysis suggests the formula PdRhO. This compound should have an oxygen content of 7.07 pct, which is within the range of error of the oxygen analysis. However, until a more careful stoichiometric study is made, it is suggested that the formula be written

Jan 1, 1965

By Qin Li

An highly active absorbent with oxidization based on fly ash, lime and additives was prepared. Experiments of simultaneous desulphurization and denitrification were carried out using fixture bed and duct injection. The influential factors for the absorptive capacity of the absorbent were studied. The absorptive capacities of 120.7mg for SO2 and 43.7 mg for NOx were achieved at a Ca/(S + N) molar ratio 1.2, respectively, corresponding removal efficiencies of 87% and 76%, while spent absorbent appeared in the form of dry powder. The optimal temperature and humidity of flue gas treated with this process were shown to be approximately 50\\176 and 5% respectively. The mechanism of removal for SO2 and NOx was investigated. In comparison with traditional dry FGD, this process appears to have lower cost, less complicated configuration and simpler disposal of used absorbent. The valuable references can be provided for industrial application by this process. The foreground of application will be vast in China and in the world.

Jan 1, 2006

By A. M. Sarem, J. M. Campbell

Molecular refraction is introduced as a new and improved third parameter for prediction of the PVT behavior of hydrocarbon systems. This parameter, characterizing the complex as well as the pure hydrocarbon systems (1) is a direct measure of London dispersion forces which affect the PVT behavior; (2) can be measured directly, accurately and easily for complex as well as pure hydrocarbon systems; (3) varies significantly between the reference substances thus allowing accurate interpolation of PVT properties; and (4) has a fundamentally sound basis. Molal average molecular refraction was used with the pseudocritical mixing rule proposed by Leland and Mueller to predict the molal volume of liquid and vapor for 84 published data points on nC4-nCI0, Cl-nC5, Cl-nC4-nC10 systems in the region of coexisting vapor-liquid and at the critical point. The same technique was applied to predict the densities of liquid hydrocarbon mixtures in the two-phase and single-phase regions near the critical point for seven different systems each having different properties of the heptanes-plus fraction, but all simulating the fluids of either gas-condensate or volatile oil reservoirs. A modification of the Leland-Mueller mixing rule for the determination of pseudocritical properties is also presented which yields more accurate liquid density predictions than the original form when used with the proposed third parameter. INTRODUCTION The PVT behavior of multicomponent systems has received widespread attention in the literature in recent years. A large portion of the reported work has stemmed from attempts to overcome the inherent difficulties encountered when using the standard compressibility-factor chart which shows 2 as a function of reduced temperature T, and and reduced pressure p,. This chart assumes that z, is constant for all systems. The error in this assumption is not pronounced for pipeline-type gases high in methane and low in heavy ends, particularly when contained at moderate pressures. For such gases the error in the calculated z is usually less than 2 to 3 per cent. However, the reliability of this approach becomes somewhat nebulous for gas condensate and volatile oil systems at high pressure. One logical approach has been to recognize the variation of 2,. This idea was first suggested by Meissner and Seferianl and used by Lyderson, Greenkorn and Hougen2 to prepare extensive tables of thermodynamic properties. Other third parameters have been proposed by Stockmeyer, Kihara, Riedel, Lightfoot, Bloomer and Pitzer. These were tested by Satter and Campbel13 for many gas mixtures and it was shown that they were inter-related. All of these third parameters have a common fault — they cannot be directly evaluated for the heptanes-plus fraction. Consequently, one necessary requisite of an improved method for predicting the density of multicomponent hydrocarbon systems, was development of a third parameter that could be evaluated for that fraction. PREVIOUS MULTICOMPONENT DENSITY PREDICTION METHODS Sage and Lacey4 suggested a method of using partial molal volumes for computing the density of hydrocarbon gas mixture for pressures to 3,000 psi. In this technique, they approximate the complex multicomponent gaseous mixtures by a quarternary system of methane, ethane, propane and butane. Sage, Hicks and Lacey5 suggest a method of using partial molal volumes for computing the density of hydrocarbon liquids. The results agree within 3 per cent of the experimental values. However, the composition range is limited to about 10 per cent by weight of methane. Consequently, this correlation does not cover the low-molecular-weight liquid similar to natural gasoline and high-pressure gas condensates.

Jan 1, 1966

By A. D. Trippel

The Cripple Creek Mining district is located in Teller County, Colorado, 30 km west of Colorado Springs and 9 km southwest of Pikes Peak (Fig. 1). Since its discovery in 1891, the district has produced almost 21 million tr oz of gold (Gott et al., 1967), most of which has been from high-grade vein deposits. Globe Hill is located in the northern part of the district (Fig. 2). Production from its summit has yielded over 100,000 tr oz of gold. Early production was concentrated along high-grade veins and fault structures, but emphasis was soon placed on the extensive, low-grade (0.0X oz/t), breccia-hosted mineralization. From 1977 to 1981 Newport Minerals, Inc., a subsidiary of Gold Resources, Inc., mined 680,000 t of low-grade gold ore from the Globe Hill pit (Fig. 3) and production is expected to resume in 1986. These strongly-altered and -oxidized breccias are amenable to bulk-mining methods, and thus similar deposits are currently being sought elsewhere in the district. Numerous publications and reports discuss the breccia-hosted mineralization at Globe Hill. They include Cross and Penrose (1895); Argall (1905, 1908); Lindgren and Ransome (1906); Keener (1962); Peters (1982); Thompson, Trippel, and Dwelley (1985); and Trippel (1985). This preprint is a summary of the recently-completed research documented by Trippel (1985).

Jan 1, 1986

By F. B. Foley

A description of tests made by a committee of the Division of Engineering of the National Research Council to determine whether velocity of impact affects the formation of Neumann bands. FOREWORD Not infrequently, in the case of the failure of a metal structure, such as a bridge, tank, airplane, gun carriage, etc., a doubt arises whether the failure was due, among other causes, to the effect of an overburden or of an explosive maliciously or accidentally exploded in contact with it. As few means of discriminating between the effects of these causes have been known and these means were of a rough qualitative character, it was surprising to find in the record of an inquiry into the failure of a structure, the statement that, by observations on the Neumann bands in the structure, it was possible to determine the speed of breakage in the metal and to distinguish between a fracture caused by an explosion and one caused by an ordinary mechanical strain. Such a criterion, if well proved, was of value to the explosives experts of the Bureau of Mines, the Ordnance Department of the United States Army and the Bureau of Ordnance of the United States Navy, but search showed no record of it in the literature nor did any of the metallurgists and metallographers consulted know of any data on which such a criterion could be based having been assembled and critically studied. However, it was universally held that there was promise in the idea and that there existed unique facilities at the Bureau of Mines Experiment Station at Pittsburgh for the preparation, under definitely known conditions, of material for study by metal-lographers, and that material of value might also be obtained from the proving grounds of the Army and Navy. Therefore, with the approval of the Director of the Bureau of Mines and the Chiefs of Ordnance of the War and Navy Departments, the Chairman of the Division of Engineering of the National Research Council, on April 12, 1919, appointed a Committee on the Investigation of Neumann Bands, which has since been engaged in this study and which, after some slight change in its personnel, consists now of the following: Dr. William Campbell, Advisory Metallurgist, Bureau of Ordnance, Navy Department. F. B. Foley, Metallurgist, Bureau of Mines. S P. Howell, Explosives Engineer, Bureau of Mines. Comdr. O. M. Hustvedt, U. S. N., Bureau of Ordnance, Navy Department. Dr. Charles E. Munroe, Chief Explosives Chemist, Bureau of Mines.

Jan 9, 1922

Current models for the origin of banded iron-formation (BIF) derived in situ iron ore deposits assume that the typical chert and iron oxide banded BIF is the primary rock from which enriched iron ore deposits arise by the selective leaching of quartz and the residual accumulation of the iron oxides. Weathering extends to the base of all the hematite deposits of the Hamersley Province, which lie within the saprolitic weathering zone, as shown by the preservation of the primary textures, and are overlain by a hydrated goethite zone representing the solum. Since groundwater typically contains dissolved silica, derived from the hydrolysis of silicate minerals, greatly in excess of the saturation solubility of quartz, it is incapable of removing quartz from below the watertable, and quartz is preserved in all saprolites derived from quartz bearing rocks. Quartz may be dissolved in the solum due to the influx of meteoric water having little or no dissolved silica, but soil-forming processes that dissolve quartz likewise alter the oxides by hydration and transposition with consequent destruction of primary textures, and there is no suggestion of soil-forming processes having produced the deposits, which typically extend to considerable depths below the water-table. A characteristic feature of the typical hematite orebodies is the unaltered nature of the iron oxides in the ore compared to those in the adjacent cherty BIF. Although the solubility of ferric iron at >10 ppb is much less than quartz, any process capable of dissolving the huge volume of quartz must also affect the iron oxides, but evidence of this is completely lacking in most ore deposits. Hydrothermal alteration at Koolyanobbing in the Southern Cross Province affects both cherty BIF and ore, and clearly shows equal mobilisation and recrystallisation of hematite within quartz/hematite veins and in the surrounding cherty BIF, which shows no evidence for the selective leaching of quartz. Similarly, any metamorphic process capable of removing all quartz from BIF would leave characteristic evidence in the remaining oxides. However, a hydrothermal process may account for at least portions of certain ore deposits, in which the chert bands have been replaced by carbonates at comparatively low temperatures, to produce a quartz-free magnetite/ carbonate rock that is readily upgraded to high-grade ore by supergene dissolution of the carbonates. This process is interpreted to have formed high grade ore at Mt Gibson, Koolyanobbing æAÆ Deposit and Mt Tom Price North Deposit. In addition to carbonate replaced cherty BIF at Mt Gibson in the Murchison Province, there are extensive sequences of magnetite BIF without chert bands, and this chert-free facies of BIF is interpreted as the precursor to the majority of in situ hematite ore deposits, through oxidation and weathering of magnetite and iron silicate and carbonate minerals. The world-class martite/microplaty-hematite deposits of the Hamersley Province are a special case of BIF-derived iron ore deposits that were initiated during the Proterozoic era. Evidence from overlying Wyloo Group conglomeratic horizons containing clasts of Hamersley Group BIF indicates that microplaty-hematite formed within the clasts before deposition, and that Proterozoic subaerial oxidation and weathering of uplifted Hamersley Group formations produced the microplaty-hematite in both chert-free and cherty BIF.

Jan 1, 2002

By A. J. Hendron, D. U. Deere, F. D. Patton, E. J. Cording

In the design of structures founded in the near-surface rock, a distinction may be made between those problems that are related to the strength of the rock mass, and those that are related primarily to the compressibility of the rock mass. The mining engineer deals almost exclusively with problems involving strength in the design of open-pit slopes and underground openings. The civil engineer is similarly concerned with strength problems in the design of vehicular and water tunnels; underground power plants; cut slopes in rock for highways, canals, and spillways; and in the study of the sliding resistance of the foundations of gravity dams and the abutments of arch dams. Moreover, the civil engineer encounters problems in which the compressibility of the rock becomes the key element in the design. These problems include settlement of heavy structures supported on rock, deformation of the abutments of arch dams, and deflection of pressure tunnel linings. The design problems listed above are still solved largely on the basis of experience and rule-of-thumb. However, recent developments in rock mechanics give promise of providing more realistic approaches to certain aspects of the design. This paper, presents some of the more important recent developments which contribute to an understanding of rock behavior and which aid in design of rock structures. Typically, four steps are involved in the design of a structure, whether it be a machine element, a structural member of a building, or a structure in rock. These steps are listed below:

Jan 1, 1967

By A. Galip Ulsoy, K. V. S. Sastry

"This review paper is intended to provide, the mineral process engineer with an introduction to the concepts, terminology. and practice of mineral process control. It also provides an extensive sampling of the vast body of literature relevant to this topic. The topics discussed include the principles of automatic control, instrumentation, mineral processing unit operations, process modeling and simulation, and process and plant control. IntroductionEconomically accessible higher-grade ores are being rapidly depleted, and at the same time the demand for mineral raw materials continues to increase. Mineral recovery from the remaining low-grade or finely dispersed ores requires grinding for liberation. High energy consumption during grinding and poor efficiency associated with the beneficiation of fine minerals are two important problems facing the mineral industry . These problems, coupled with advances over the last 10 to 15 years in the areas of process modeling, instrumentation, computer technology and control theory, have made automatic control of mineral processing systems an important research area(23,52,66,67,120,129,152)."

Jan 1, 1981

By A. G. Smelley

As part of research conducted in its mission to effect pollution abatement, the Bureau of Mines, U. S. Department of the Interior, is developing a dewatering technique that allows for disposal of phosphatic clay wastes, for reuse of water now lost with clays, and for reclamation of mined land. The technique utilizes a high-molecular-weightnonionic polyethylene oxide polymer (PEO) that has the ability to flocculate and dewater phosphatic clay wastes. A synergistic flocculation study was made to determine whether a portion of PEO could be replaced by other reagents. Several groups of reagents were tested: (1) those that increased the zeta potential of the phosphatic clay wastes; (2) those capable of hydrogen bonding; and (3) those which flocculated the phosphatic clay waste. Reduction in PEO consumption occurred only with addition of those reagents able to flocculate the slime. The use of natural guar gums resulted in a lower PEO requirement and also yielded a dewatered product of higher solids content, 43 to 45 percent, versus 33 to 35 percent obtained with PEO alone.

Jan 1, 1980

IN this paper an attempt is made to describe the sluicing operations on the tin fields of north-eastern Tasmania. No claim is made to completeness, for much of the ground has already been covered, and nothing is to be gained by needless repetition. On this account some portions of the subject have obviously received but scanty attention in order that others may be rather more fully dealt with; for instance, figures referring to the accuracy of various methods of valuing alluvial deposits, particulars of efficiencies, and water duties on both overburden and drift; also, the system of recording water distribution, &c.The plans of the tin-streaming shed, sluice and feed·race, and overburden tail-race represent types of the most modern design.The principal alluvial deposits being worked at the present time are situated either in the ancient or modern bed of the Ringarooma river or its tributaries. This river flowed in a north-easterly direction, receiving numerous tributaries on either bank, and finally emptying into Boobyalla harbour. The most important of these tributaries, from a mining point of view, are the Cascade, Main creek, Weld and Frome rivers (which unite just before joining the modern Ringarooma), Wyniford river, and Bradshaw's...

Jan 1, 1911

By J. S. Vanick

An extremely hard, tough, and strong, white or chilled cast iron has been applied for the past several years to industrial and mining services in which its unusual properties have been confirmed by its ability to deliver in many instances much better performance than plain chilled iron, or other wear-resistant materials. It is being produced regularly by alloying a good base composition of chilled or white cast iron with essentially 4 to 6 per cent of nickel and 1 to 2.5 per cent of chromium. Such a material can attain a hardness exceeding 600 to 750 Brinell as against 380 to 530 for corresponding grades of plain chilled iron. The strength is approximately doubled and the toughness significantly increased. These properties make it especially useful for many applications requiring a high hardness for resistance to wear, abrasion, attrition, deformation; to some extent to high compressive loading and to a lesser but important degree to corrosive action. A wide variety of commercial castings is being successfully produced from this iron, ranging in size from the small grain-grinding plates or burrs through medium-sized castings such as sand pumps up to large, heavy castings such as rolls for metal rolling or cement grinding. The composition of this white cast iron may be roughly bracketed within the range shown in Table 1.

Jan 1, 1933

By W. A. Naismith, R. T. Pakalnis

The Umgal a section of the We1gedacht Exploration Company Ltd., a member of the Rand Mines Group, is situated near Utrecht in the province of Natal, South Africa. Two coal seams, the Alfred and Gus, are mined to fulfill commitments to both inland and export markets. To increase extraction in the high quality Alfred Seam, pillar extraction, known locally as stooping, was introduced to the mine in September, 1980. Mining is a conventional cut-drill -blast operation and takes place under a unique set of geological conditions viz. moderately thick seam at 3.5 m; rapidly varying cover from 25m to 120 m; an overburden containing competent sandstone and dolerite horizons. In order to improve the understanding of the manner in which the pillar and overburden interact during pillar extraction, a largely visual system of monitoring backed up by roof-floor convergence measurements was employed. Preliminary analysis of the observations suggests that roof collapse or goafing occurs in three phases but is only initiated once a critical amount of convergence has taken place.

Jan 1, 1983

By T. E. Smith

"This paper describes the application of a motor-driven flywheel unit, known as a peak shaver, to compensate for the cyclic load fluctuations of a large electric dragline installed at Pine Point Mines, near Great Slave Lake in the Northwest Territories. Of particular interest in this application is the fact that the power system supplying the dragline is a relatively small isolated system, with the major generating source approximately 170 miles from the mine.The cyclic load fluctuations of the dragline are theoretically capable of producing a maximum swing of up to 11 megawatts, which approaches nearly 50% of the installed generating capacity. To reduce these load fluctuations to acceptable limits various alternatives were considered, leading to a decision to install a peak shaver to optimize the operations of both the mine and the power system. Without the peak shaver, the dragline operations would be severely curtailed and additional diesel generation would have to be run at considerable expense, otherwise the power system frequency fluctuations would be totally unacceptable. With the peak shaver, power and frequency fluctuations are kept within tolerable limits, and optimum economic operation of the diesel generation is obtained.The paper outlines the steps leading to the selection of the peak shaver as the compensating device, describes the equipment installed and gives details of operating experience with the dragline/peak shaver combination since installation early in 1979. This .peak shaver is the first of its kind in North America, the only other peak shaver installation being in Australia.IntroductionPine Point Mines Limited owns zinc-lead mining and milling operations located at Pine Point, Northwest Territories, 5 miles south of Great Slave Lake (Fig. I). The company is staffed and managed by Cominco Ltd., which has a 69% interest in Pine Point Mines.Mining activity in the Pine Point area was first recorded in 1898, when the Yukon gold rush was on, but when the zinc/lead showings in the Pine Point area did not yield much in the way of gold, interest in the area soon waned. Cominco Ltd. first acquired some claims in the Pine Point area in 1928, but interest was sporadic until the early 1950s, when extensive exploration indicated rich pockets of zinc/lead ore near the surface. Pine Point Mines Limited was formed in 1951, with Cominco acquiring a majority interest in the company."

Jan 1, 1980

By Carl A. Allen

Page Introduction................... 367 FactoRs Affecting the Choice of Method......... 367 Review of Stoping Methods.............. 368 Underhand Stoping................ 368 Overhand Stoping................ 370 Longitudinal or Flat-Back Stoping........... 371 Rill-Cut Stoping................. 372 Saw-Tooth Back Stoping.............. 372 Shrinkage Stoping................ 372 Combination Stoping................373 Side Stoping.................. 374* Breast Stoping................. 374 Sublevel Stoping.........,....... 374 Square-Set Stoping................ 376 Filling Methods................. 376 Caving Methods of Mining......... 376 Top Slicing.................. 377 Sublevel Caving................. 379 Block Caving ................. 380 Back Caving into Chutes.............. 381. Costs of Mining Methods.............. 382 Costs of Willing and Blasting. Comparison of Stoping Methods ... 383 Lighting................... 386 Timbering and Handling Ore in Stopes.. A Comparison of Square-Set and Top-Slicing Methods..............386 Tramming.................... 380 Mining oF the Massive Porphyry CoppeR Deposits ....390 Utah Copper and Boston Consolidated Mines.....391 Ray Consolidated Mine.............. 392 Miami Mine.................. 392 Inspiration Mine................ 395 Ohio Copper Mine...........395 Development.................... 398 Appendix..................... 399 Costs of Mining................. 399 Costs of Development............... 406

Jan 1, 1915

Discussion of the paper of E. L. deGolyer, to be presented at the Colorado meeting, September, 1918, and printed in Bulletin No. 137, May, 1918, pp. 987 to1000. J. A. UDDEN,* Austin, Tex. (written discussiont).-I have read Mr. E. L. deGolyer's paper on The Theory of Volcanic Origin of Salt. Domes, with a great deal of interest. It seems to me a very able summary and discussion of the various theories set forth to account for the origin of our salt domes on the coast. It has always appeared to me that what we need is more observations on the facts involved and I regret very much that so far we have not been able to devote much time to the study of our salt-dome fields on the coast in this State. One feature that I do not find mentioned in Mr. deGolyer's paper is the so-called "cap. rock" overlying the salt. The nature of this rock seems to vary from a coarsely crystalline limestone to a fine-grained limestone containing sand and in which the limestone seems to be intersticially introduced material. We should be prepared to accept, if necessary, "more than one theory. To my mind, the igneous theory and the artesian theory, if I may so call it, may very well both be true. The "squeeze" theory and the artesian .theory may,, it seems tome also, jointly explain the phenomena. Neither the volcanic nor the salt "squeeze" theory explains the presence of the cap rock. The latter certainly does not explain the extensive sulphur deposits which occur in association with the cap rock. Whichever additional theory will be found best to explain the salt-dome structures, when we shall know them better, it seems to me that the theory first advanced by R. T. Hill and later elaborated by G. D. Harris, is not likely to be entirely replaced. Whatever cause has first set into action an upward circulation of gases and liquids in our salt domes, it seems to me that to a gentle circulation of the kind postulated by their theory is to be ascribed the uppermost and the later phenomena in our salt domes on the coast, with which we are most familiar; such as the cap rock, the sulphur, and the gypsum and anhydrite deposits.

Jan 7, 1918

By F. E. Armstrong

Tritiated water has been used as a tracer to follow the path of leach liquids as they flow through a copper-mine dump. Semipermeable layers, produced within the dump by compaction and "stratification" of deposized dump material, restrict the vertical movement of water. Knowledge of this restriction would aid in the optimization of the leaching process. The portion of the dump of particular interest was approximately 2,000 feet long, 800 feet wide, and 200 feet high. A total of 94 curies of tritiated water was injected into the dump at the rate of 650 gpm over a period of 39 hours. The leach liquid was sampled at natural surface outflows and through a series of wells, some drilled to the bottom of the dump and others to intermediate levels. More than 3,300 samples were analyzed, most by liquid scintillation counting, but a few hundred by gas counting. Data obtained permitted calculation of flow paths, recycle times, total fluid volume, and estimates of retention times in various portions of the dump.

Jan 1, 1971

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

It is imperative that the hydrogeologic frame- work and the ground water flow systems of a Potential mine area be investigated prior to initiation of mining. Such investigations are necessary so that potential mine water inflow problems can be anticipated and controlled. Obvious difficulties can arise if large inflows of ground water occur in underground workings. Costs of water removal and disposal, if not foreseen and included in economic planning, can severely limit or eliminate profit from a mining operation. Safety problems associated with large inflows are an additional potential problem. The inflow of water into a mine necessarily alters the associated ground water system. The inflow also may impact nearby surface water regimes, depending upon the interaction of the surface water and ground water systems. The inflow of water into a mine inevitably causes a decline in the ground water levels in the vicinity of the mine. This decline may be restricted to a small area or it may extend a considerable distance, depending upon the hydrogeologic properties of the associated hydrostratigraphic units. A decrease in surface flow will result if the area of ground water level decline intersects a stream or spring that is hydraulically connected to the ground water system. Mine inflow problems historically have been evaluated after-the-fact. Premining hydrologic investigations only recently have been initiated. Brown's (1977)* report on anticipated hydrologic impacts of oil shale mining in the Piceance Basin of Colorado is an example of premining hydrologic planning. Observed difficulties inherent in designing a data collection network and then utilizing the data to predict mine inflow have led us to the preparation of this manuscript. This manuscript reflects a two-phase effort. The first phase describes and develops analytical and numerical techniques for mine inflow prediction. Emphasis in this section is placed on the selection and application of data collection techniques and data analysis procedures. The second phase applies the prediction technique(s) developed during phase 1 to two existing mines. The objective of phase 1 efforts is to evaluate the hydrologic variables associated with surface water systems and ground water systems that can affect the inflow of water into an underground mine. Subsequently these variables are incorporated into predictive techniques for estimating underground mine water inflow and its effect on associated ground water and surface water systems. The specific objectives of phases 1 and 2 are to: 1) Determine the hydrologic parameters required for predicting underground mine water in- flow and the potential effects of the inflow on surface and ground water systems. The hydrologic parameters represent both premining and past initiation conditions. 2) Outline methods for obtaining the necessary input data for the predictive techniques in pre- mining and post initiation periods. 3) Present existing numerical techniques for predicting underground mine water inflow including assumptions Ad required input. 4) Evaluate existing numerical techniques previously tabulated based on their applicability to mine water inflow prediction. 5) Attempt to develop analytical techniques for predicting underground mine water inflow. 6) Develop, through modification of existing models, a general mathematical model as a numerical technique for predicting underground mine water inflow and the resultant effects on surface and ground water systems. 7) Apply the predictive techniques to two existing mines selected for this purpose. 8) Compare the predicted inflow rates to measured inflow rates at both mines. 9) Compare predicted impact on district hydrology to observed impacts where possible. 10) Evaluate the predictive technique.

Jan 1, 1986

By A. W. Fahrenwald

The art of flotation has developed rapidly. Numerous technical staffs and individual investigators have, by their combined efforts, developed practicable methods of concentrating ores which ten or even five years ago were considered complex and impossible of commercial treatment. Also the work of those who have been engaged in pure research on the fundamentals of flotation has helped greatly to expedite the general development of the process. However, in spite of the highly successful practical operation of the flotation process, results are obtained and things happen that we are unable to explain completely, although much is known about the theory of the process. The rapid stride in flotation concentration, it is noteworthy to point out, is due to the freer exchange of facts and data by the staffs of the larger mining companies and the patent controlling corporations, and by investigators in general. Generally speaking, one may visit any mining plant and by presentation of proper credentials, be shown all that is going on or that is being done.

Jan 1, 1925

By Drew GJ

Smelting is a process in which heat is applied to ores to produce metals. Impurities are removed by segregation in the slag, or converted to gases or sublimates and discharged up the flues. Mate- rials delivered into the smelter have generally been previously concentrated or processed at the mine, and the size of their particles, and also their chem- ical composition, greatly affect the smelting proc- ess. Some impurities are more difficult to remove than others, and are more objectionable in the finished product. The first metal mine in Australia was opened near Glen Osmond in South Australia in 1841, for silver-lead ore. It was followed by the Kapunda Mine for copper in 1844 and by the very signifi- cant Burra Mine, also for copper, in 1845 (Figure 1). A major part of their ores could not be exported profitably for smelting in England and Wales where the large smelters were then located. In addition to treating ores from Cornwall these also smelted ores from recently opened mines in Cuba, Chile, and Mexico. The Welsh smelting process (Figure 2) was developed over a period of years to utilise Welsh coal to treat copper ores particularly from Corn- wall. The first step consisted of a calcination to remove sufficient sulphur from sulphide ores so that subsequent melting operations would produce copper matte, a copper-iron-sulphide which melted at about 1050¦C. Subsequently refined to white metal with the addition of carbonate and oxide ores when these were available, and often through an intermediate step of blue metal, this matte was finally oxidised to pure copper, or as pure as it could be made in those days. The movement of metal towards greater purity was matched by a reverse flow of slag, carrying reducing quantities of copper, so that the slag rejected from the first melting process carried the minimum quantity of copper. Chemical analysis was virtually unknown. Materials were assayed in the laboratory by a small scale smelting process, and the purity of the final refined copper was judged b} the ease with Mhich it could be hammered into thin sheets.

Jan 1, 1987

By M. Fornaro

A small size quarrying activity (3 different quarries with an overall production in blocks less than 10.000 m3/year) has been exploiting for a long time the ?Tonalite? deposit of Adamello-Presanella. In 1967, given the outstanding natural beauty of the area, a natural park has been established with the aim of preserving environmental quality and, at the same time, of providing a sustainable development to the area. Because of the potential impacts of a mining activity in such a context, a specific study has been recently carried out in order to define if and how the quarries could co-exist with the park, beyond the ?administrative results? of a classic environmental impact assessment. The paper deals with the process that drove to the conclusion that the activities are not ?a priori? incompatible with the aims of the park. In the opinion of the authors, a responsible quarry management, which must take inspiration from the care given to environment by traditional alpine productive activities (e.g. the use of water, of wood, and of the stone itself), and take advantage of modern technologies in terms of emissions and safety, can be considered not only compatible with the protected area, but even able to positively contribute to the protection of the land and environment (Barisone et al., 2001). A series of specific prescriptions, which have been adopted by the Park Authorities after this study, are also discussed in the paper: only the definition of suitable spatial and temporal limits, the adoption of effective technical practices and a strict control are considered to be able to drive this ?exceptional? activity towards the final goal of real sustainability.

Jan 1, 2007