Search Documents

By R. Gebrekristos

It is commonly accepted that three types of aquifers exist in the Bushveld Complex: (a) alluvial aquifers in areas of river courses, (b) weathered bedrock aquifer formed by the in-situ weathering of the bedrocks, (c) fractured aquifers underlying the weathered aquifers controlled by the regional and local fracturing of the crystalline rocks. Hydrogeological studies conducted in the Critical Zone of the Bushveld Complex in the western limb show that the UG2 pyroxenite layer is of a particular interest and has a unique aquifer property. It yields much of the groundwater inflow into some mines and can be classified as the most important aquifer in the vicinity of the mining zone. The UG2 pyroxenite aquifer is restricted to the dipping UG2 pyroxenite unit. The unit weathers more intensely than the surrounding norites and anorthosites and is characterized by deeper weathering horizons (two to three times deeper than the surrounding rocks). For much of the UG2 mining area between depths of 35 ? 80 m, stoping of the UG2 takes place approximately 5 ? 7 m below the UG2 pyroxenite aquifer, and usually there is no groundwater inflow into the mine workings. However, unsealed deep exploration boreholes intersecting the UG2 pyroxenite and reaching underground mine workings, or mine roofbolts penetrating the weathered pyroxenite aquifer from underneath, can result in significant groundwater inflows into the underground workings. The reason as to why the UG2 pyroxenite weathers more than the norites and anorthosites has not been fully studied but is suspected to be due to the bedding planes of the unit and mineralogical composition of the particular pyroxenes forming the unit, which result in preferential physical and chemical weathering under atmospheric conditions. The weathered pyroxenes form sand-sized, rounded grains with improved effective porosity and permeability suitable for the storage and passage of groundwater. The orientation of the pyroxenite aquifer can easily be determined as it dips with the Bushveld layered strata. No-flow boundaries can be assumed on the hanging- and footwall of the pyroxenite aquifer and the flow rates can be estimated using 2-dimentional analytical equations. However, this must be confirmed with strong conceptual models since the existence of a fracture network connecting the pyroxenite aquifer with the overlying weathered and/or underling fractured aquifers can complicate the system, lowering the accuracy of analytical models and necessitating the utilization of numerical models.

Jan 1, 2012

By M. Sakata, H. Hata, K. Haiki

"Most of the secondary ZnO contains fluorine (F) in large quantities. Serious troubles at the zinc electrowinning are occurred by the cathode corrosion caused by F, therefore we developed iron compounds as F-adsorbents used in zinc sulfate solution. The iron compounds can be reused repeatedly as F-adsorbents because they can adsorb/desorb F alternatively depending on the pH. Moreover, if the adsorptive capacity decreases, we can dissolve and re-synthesize them easily. In this paper, results of the experimental process which consists of five steps (leaching, F removal, Cl removal, purification and electrowinning) to produce high purity electrolytic zinc from the secondary ZnO are reported. INTRODUCTIONThe recycle material for zinc, secondary ZnO, contains large amounts of fluorine (F) and chlorine (Cl) which are halogen elements, compared with calcine obtained by roasting of zinc sulfide concentrate. The halogen elements cause adverse effects in the zinc electrowinning process and particularly F causes corrosion of aluminum cathode plates and eventually sticking of electrodeposited zinc and therefore, F concentration in the electrolyte is controlled to less than approximately 20 mg/L. There are several methods to remove F from secondary ZnO, such as leaching with Na2CO3 or NaOH solution [1-2], vaporizing in a rotary kiln by roasting at 1000 to 1200 degrees C [3-4]. However, up to the moment, there has been no effective method for the removal of F from zinc electrolyte and it has been a big obstacle in treatment of secondary ZnO in electrowining of zinc.The authors, therefore, developed an iron compound used as an adsorbent of F in the zinc sulfate solution [5-8]. This iron compound is Akaganeite that has a crystalline structure of ß-FeOOH. Akaganeite is synthesized by neutralization of FeCl3 solution containing a small amount of SO4 2- with Na2CO3. When this iron compound is immersed into weak acidified zinc sulfate solution, F in the solution is adsorbed. F adsorbed in the iron compound is removed by immersing in weak alkaline solution and the iron compound can be reused as F adsorbent."

Jan 1, 2012

By L.L. Wyman

The exact nature of the changes that take place in the iron-nickel alloys, giving rise to the interesting and useful expansion alloys in the Invar range, has yet to be fully understood. Similarly, the ternary iron-nickel-cobalt alloys, which also possess such commercially useful expansion characteristics,1,2 are concerned with transformations that appear to be identical with those found in the parent iron-nickel alloys. The investigations on iron-nickel alloys in the range 26 to 29 per cent Ni have been reported by several authors3-9 wherein it is shown that there are factors other than temperature, such as stress and grain size, which play an important part in determining the temperature at which the low-temperature transformation takes place. It will be shown in this paper that the ternary iron-nickcl-cobalt alloys having nickel contents comparable to the alloys mentioned above behave in a parallel manner. The alloys in the range of 26 to 31 per cent Ni and 16 to 21 per cent Co have a coefficient of expansion of about 4.0 X 10-6 per degree Centigrade, and the alloys in this range of composition find considerable application in making glass-to-metal seals, because these expansion properties so well match commercial glasses. The behavior of these alloys is not a simple matter, for it has been observed in alloys of 28.5 per cent Ni and 18.5 Co that severe working ran cause the appearance of a second phase having a needlelike structure similar to the martensite structure in carhon steels. Fig. 1 shows the change brought about in an alloy of this composition when a strip of this material was cut with tin shears. This second phase has been identified as the body-centered cubic alpha phase, and it is the purpose of this paper to describe the results of some of the preliminary investigations in the study of the changes involved in these alloys. Materials The past work on these alloys has concerned itself primarily with materials made by the usual casting procedure and involving the use

Jan 1, 1939

By L. L. Wyman

The exact nature of the changes that take place in the iron-nickel alloys, giving rise to the interesting and useful expansion alloys in the Invar range, has yet to be fully understood. Similarly, the ternary iron-nickel-cobalt alloys, which also possess such commercially useful expansion characteristics,1,2 are concerned with transformations that appear to be identical with those found in the parent iron-nickel alloys. The investigations on iron-nickel alloys in the range 26 to 29 per cent Ni have been reported by several authors3-9 wherein it is shown that there are factors other than temperature, such as stress and grain size, which play an important part in determining the temperature at which the low-temperature transformation takes place. It will be shown in this paper that the ternary iron-nickcl-cobalt alloys having nickel contents comparable to the alloys mentioned above behave in a parallel manner. The alloys in the range of 26 to 31 per cent Ni and 16 to 21 per cent Co have a coefficient of expansion of about 4.0 X 10-6 per degree Centigrade, and the alloys in this range of composition find considerable application in making glass-to-metal seals, because these expansion properties so well match commercial glasses. The behavior of these alloys is not a simple matter, for it has been observed in alloys of 28.5 per cent Ni and 18.5 Co that severe working ran cause the appearance of a second phase having a needlelike structure similar to the martensite structure in carhon steels. Fig. 1 shows the change brought about in an alloy of this composition when a strip of this material was cut with tin shears. This second phase has been identified as the body-centered cubic alpha phase, and it is the purpose of this paper to describe the results of some of the preliminary investigations in the study of the changes involved in these alloys. Materials The past work on these alloys has concerned itself primarily with materials made by the usual casting procedure and involving the use

Jan 1, 1939

By AIME AIME

THE second meeting of 'the Open-Hearth Committee, 'sub-division of the Iron and Steel Committee of this Institute, was held at the Hotel Cleveland, Cleveland, Ohio; on Oct. 13-15. On Oct: 12, the Open-Hearth Superintendents visited the plants of the Youngstown Sheet and Tube Co. and. the Republic Iron and Steel Co. These men were courteously entertailled by the two companies and every facility for a thorough inspection was furnished. Luncheon was severed at the plant bf the Youngstown Sheet and Tube Co. The meeting was opened Tuesday morning with addresses by J. V. W. Reynders, President of the Institute, and Herbert M. Boylston, Chairman of the Ohio Section of the Institute. E. A. Whitworth, of the Gathmann Engineering Co., presided at the meeting and L. B. Lindeinuth was secretary.

Jan 1, 1925

By T. R. Cass, M. R. Achter

A technique for measuring the creep and rupture strength of nickel specimens bonded by sintered oxide layers has been developed for the investigation of the role of grain-boundary oxide in the oxidation strengthening of nickel during creep at 817 °C. Prom the inverse dependence of the rate of bonding on the thickness of the starting oxide, it is suggested that the rate of diffusion of Ni++ through NiO is the controlling process at the start of sintering. Cornparisons of the creep and rupture strength and of the microstructure of sintered couples with conventionul creep specimens suggest rupture in nickel is prevented by load-bearikzg, ikltergranular layers of oxide. A number of recent investigations have shown that at high temperature and low stress the creep-rupture strength of nickel and nickel-base alloys may be much greater in air than in an inert gas or vacuum.'-7 For example, at 817°C and 2500 psi, nickep failed in vacuum in 48 hr but not in air after 4000 hr, and a Ni-Cr-A1 alloy5 at 1038°C and 3000 psi failed in vacuum in 4 hr but not in air after 731 hr. Fig. 1 is a typical creep curve in air for materials experiencing this pronounced environmental strengthening. A common feature of these curves is the entry into a third stage of accelerating creep, concurrent with the for-

Jan 1, 1962

By D. E. Peacock, B. Harris

The mechanical behavior of a niobium (columbium)TUNG alloy containing 20 wt pet Ta. 15 wt pet W, and 5 wt pct Mo has been studied in the temperature range 77° to 423°K. All specitrzens tested, apart from those into which oxygen was introduced deliberately, were fully recrystallized at 1500°C, had an average grain diameter of approximately 0.03 mm, and a combined carbon, ox-vgen. nitrogen, and hydrogen content of not not more than 250 ppm The meckatnical behavior of this alloy was found to be similar in seine respects to that of unalloyed bcc transilion metals. Both yield and flow stresses were sensililae to changes in deformation rate and both increased rapidly as the temperature was lowered below 150°C. A detailed examination revealed, however, that most of the temperature dependencc of the yield stress could be accounted for by the temperature dependence of the elaslic, modulus, whish is not true of the unualloyed metals. In lension at moderate strain rates, the trunsition fvom ducfile to hvittle behavior occurred just belour room teunperature bur incveasing the oxygen content from 190 to 200 pptn raised the transition temperature to about 4000K. TUNGSTEN and molybdenum have been found to be very effective high-temperature solid-solution strengtheners of niobium, but the amounts of these elements that can be added are limited if the alloy is to retain useful room-temperature ductility. It has been shown, however, that partial replacement of niobium with tantalum lowers the ductile-to-brittle transition temperature of such alloys and allows larger additions of molybdenum and tungsten to be made. Some of the high-temperature properties of niobium alloys containing these elements have been reported by Bartlett et al.,' and the work presented here describes the low-temperature behavior of one of these, a solid-solution alloy containing, by weight, 20 pct Ta, 15 pct W, and 5 pct Mo. The elastic modulus, the temperature and strain-rate dependence of the yield and ultimate tensile stresses, and strain-hardening effects are discussed and compared with those of unalloyed niobium. EXPERIMENTAL MATERIAL AND PROCEDURE The material used in this investigation was produced from a 6-in.-diameter, double arc-melted ingot. This was can-extruded at about 1150°C to a 3-in.-diameter billet, and after annealing for 1 hr at 1345°C the billet was heated to 1315OC and part rolled and part forged to 0.5-in.-thick plate. The resulting material exhibited a cold-worked structure

Jan 1, 1965

By Donald J. Knight

HEAT Treatment at 1500' F of a mild steel containing 0.1 pct C, in an atmosphere which is oxidizing to both carbon and iron, results in the progressive oxidation of the metal surface with little or no change in the carbon content of the underlying metal. Further heat treatment of the scaled metal in either a neutral atmosphere or in a vacuum may or may not result in the decarburization of the metal depending upon the physical nature of the scale. It is apparent that if a continuous layer of oxide is present on the steel surface, the reaction OScale + Cmetal Cogas cannot progress since the SO formed gas would be unable to leave the oxide/metal interface. Thus, in order for the reaction to progress, the oxide must be cracked or porous. Vacuum heat treatment at 1500" F of samples with a thick continuous oxide scale showed no decarburization of the steel. However, when cracks were introduced mechanically into the scale prior to the vacuum heat treatment notable decarburization of the metal resulted and a structure as shown by Fig. 1 obtained, i.e., reduction of the crack walls to ferrite. With reference to the diagram of Fig. 2, it would appear that a mechanism of the following type takes place. Carbon atoms arriving at an oxide/metal/void interface, such as 'A', Fig. 2(a), can combine with oxygen atoms from the scale and leave the reaction site as Cogas thereby reducing the oxide to metal. On a greatly magnified scale, Fig. 2(b),this will appear as a ferrite projection along the crack wall. Carbon atoms entering this projection can react with oxygen atoms at point 'C', which is a new interface, and so on leading to a progressive growth of the ferrite along the crack wall and to the surface, Figs. 2 (c) and 1. It would appear that the only means by which thickening of the ferrite film can take place is by a diffusion of oxygen through the ferrite film to react with carbon at the newly formed ferrite/ void interface. Since the diffusion rate of carbon is reportedly much greater than that of oxygen, and since there is a low probability factor of oxygen and carbon atoms arriving simultaneously at the same site on the ferritehoid interface, there will be a tendency for more rapid lengthening than thickening of the ferrite layer, as is observed.

Jan 1, 1962

Keywords: Pyrometallurgy, Wits University, research Wits Metallurgy celebrated its centenary in 2004. The department has been at the forefront of education and research and has contributed greatly to the metals and minerals industry, both in South Africa and abroad, in terms of human resources and knowledge generation. A significant number of industry and academic leaders worldwide are Wits Metallurgy graduates. Since its early beginnings, pyrometallurgy has always been part of the curricula and research offered by the department. Pyrometallurgical activities started to expand tremendously from the middle of the 1960s, especially by the formation - together with Mintek - of the Pyrometallurgy Research Group, which continues its internationally recognised research activities today. The research efforts have been concentrated on problems associated particularly with ferroalloy, steel, stainless steel production, and PGM/Cu-Ni sulphide smelting. In recent years, research has been further expanded to physical modelling of pyrometallurgical reactors. Almost all of the specific research projects were handled from a fundamental point of view, and hence a large number of MSc(Eng) and PhD degrees were achieved by candidates under the supervision of the Pyrometallurgy Research Leaders. Moreover, a significant portion of the research results were published in internationally recognized journals and conference proceedings. Among these, Infacon and the Molten Slags, Fluxes and Salts Conference series are worth mentioning. The studies from a fundamental point of view include thermodynamics, phase equilibria, transport phenomena, kinetics, and process dynamic aspects of high temperature processes and systems, both in the solid and liquid states.

Jan 1, 2006

The 114th Annual General Meeting of The Southern African Institute of Mining and Metallurgy was held at The Country Club, Johannesburg, Napier Road, Auckland Park on Thursday, 11 August 2011. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations, and also to recipients of awards, senior members of industry, Honorary Life Fellows, past-presidents, our members and other guests, among them the following: F. Cawood, President, Institute of Mine Surveyors of South Africa C. Roode, President, Mine Metallurgical Managers' Association of South Africa M. Cresswell, Chairman, South African Coal Processing Society A. Hay, Immediate Past President, South African Institute of Electrical Engineers L. Gardner, President, South African National Institute of Rock Engineers J. Krynauw, President, The Geological Society of South Africa (GSSA)

Jan 1, 2011

By X. (Mike) Yao

Rock mechanics engineers must provide ground support designs that ensure a safe underground working environment. Unexpected falls of ground are unacceptable while ground support systems must be adequate. Ground support must be economic for the area supported and the time frame the opening is in use. While numerical modeling can be used for ground support design, empirical models are still the common useful design tools. Empirical models are best developed and improved from local experiences although some models, such as Stability Graph (Potvin et al, 1992), are in extensive use by the Canadian mining industry. To determine the adequacy of ground support practices at HBMS, a database of 50 fall of ground case histories between 1985 and 2001 was compiled. For each failure, the recorded data included: location, rock type, rock mass conditions, opening and failure geometry, installed ground support and failure mechanism. An analysis of the database was done to obtain an understanding of failure frequency association with rock types, stope geometry and installed ground support, and to assess what support design changes were necessary. The paper describes changes made to ground support and mining practices during the last five years, and the formation of new ground support standards and practices which have been successful in reducing ground falls while providing improved, efficient and economical ground support.

May 1, 2002

By Matthew Grzelak, Gulsah Erinc, David R. Chapman

"The third phase of the Bagram Drainage System project at Bagram Air Force Base in Afghanistan included construction of a shallow, 540-m long, 1.8-m inside diameter drainage tunnel. The tunnel penetrated mostly stiff to hard clayey and silty soils. The contractor’s Value Engineering Change Proposal (VECP) to use pipe-jacking with a microtunnel boring machine (MTBM) instead of the specified two-pass Earth Pressure Balance method was evaluated and supported using hand calculations. Contractor support was provided throughout the project by providing design reviews and instrumentation monitoring during construction. This paper compares the value-engineering proposal to the specified method and describes the construction conditions encountered. INTRODUCTION As part of a larger improvement project at the Bagram Air Force Base in Afghanistan, a shallow, 540-m long, 1.8-m inside diameter drainage tunnel was constructed to provide additional capacity for Coyote Creek to pass below several critical structures, including taxiways and the main runway, for mitigation of recurring flooding (see Figures 1 and 2). Overburden over the tunnel crown ranged from about 3 m to 5.5 m. An existing cast-in-place twin barrel concrete culvert runs approximately parallel to the new tunnel and is within about 8 m at its closest point. The contractor’s Value Engineering Change Proposal (VECP) to the specified two-pass Earth Pressure Balance (EPB) method (steel ribs and lagging or steel liner plate with a carrier pipe later grouted in-place) called for installation of the required drainage pipe by pipe-jacking (one-pass installation) using a slurry microtunnel boring machine (MTBM). The critical nature of the operations at the air base resulted in significant construction coordination challenges and a greater than usual need to avoid excessive settlements. Substantial restrictions were placed on drilling of investigative borings and installing instrumentation near runways and taxiways due to drill mast height. The prime contractor was SERKA TAAHHUT INSAAT A. S. (SERKA), the microtunneling subcontractor was Ludwig Pfeiffer Microtunnel GmbH & Co.KG (Pfeiffer), the jacking pipe designer was Gollwitzer Pipe and Shaft Technology GmbH (Gollwitzer), and the contractor’s tunnel engineer was Lachel & Associates, Inc. (Lachel). Lachel provided contractor support throughout the project including preparation of a VECP/Design Summary (including interpretation of existing and new geotechnical information), design reviews for jacking pipe, estimating settlement of an existing drainage structure above the new tunnel, and instrumentation planning, monitoring, and analysis during construction."

Jan 1, 2016

By Howard S. Lee

In central Colorado is a great belt of intrusive porphyry nearly 100 miles long (160 km.), extending from the Clear Creek district on the north to Aspen on the south, which includes many of the well known mining camps of the state. Near the southern end of this belt, at Leadville, the occurrence of these intrusives is most marked, resulting in intensive mineralization and the formation of a great variety of large orebodies. During the past 40 years, Leadville has been a steady producer of gold, silver, lead, zinc, manganese, iron, and bismuth, in the forms of sulfide, carbonate and oxide ores. It is the purpose of this paper to discuss pyrite alone, which, under present economic conditions, is valuable chiefly for its sulfur contents. The ore-bearing formation of the Leadville district consists of two beds of limestone separated by a layer of quartzite. The upper limeatone is carbonaceous, and is known locally as the blue limestone. It varies in thickness from 50 to 300 ft. (15 to 91 m.). The lower limestone is Silurian, known locally as white limestone, and is about the same thickness as the upper bed. Underneath the Silurian limestone is a layer of Cambrian quartzite from 100 to 250 ft. (30 to 76 m.) thick resting on Archean granite, which forms the limit of ore deposition. As a rule, there is a sheet of white porphyry above the upper, or blue limestone; a sheet of gray porphyry is associated with the blue limestone, either in or below it, but the porphyries are not so regular as the quartzites and limestones and are not always found in their expected positions. Throughout the district there is an elaborate system of faults and intrusive porphyry dikes, which have an important bearing on ore deposits. The writer has seen two or three orebodies which were not closely associated with either a fault or a porphyry dike, but if the minor fractures and water courses are considered as part of the fault system it is safe to say that all orebodies are directly traceable to one or both of these causes. The distribution of pyrite in the Leadville district is quite general; but, eliminating the smaller bodies and those containing prohibitive quantities of zinc or lead, and considering only the larger deposits commercially valuable for their sulfur, we find the chief pyritic ore-bodies extending in a zone approximately 6000 ft. (1828 m.) long and several hundred feet wide, from the Yak and Moyer, on the south; through the Louisville, Greenback, Mahala, Adams, and Wolftone, on Carbonate Hill; across Yankee Hill, and into the Quadrilateral, Denver City, and Tip Top, on Fryer Hill.

Jan 1, 1920

A study was conducted to evaluate the effectiveness of the three types of sample grinders routinely used in the mining industry for the sample preparation of gold ores with particular emphasis placed on testing their capacity to produce a representative assay sample of coarse gold ores. The grinders used in this study are the Labtechnics LM5, the Mixermill 4010 ringmill and the Keegor vertical spindle pulveriser, commonly called a Keegormill. The study was based on the preparation of samples from two sources of known coarse gold ore, the Union Reefs Gold Mine and the Brocks Creek Gold Mine in the Pine Creek region of the Northern Territory of Australia, and a fine gold ore which was from the Macraes Gold Mine in New Zealand. The Union Reefs Mine contains visible coarse gold with 30 per cent to 40 per cent of the gold in the plus 75 μm fraction of milled ore. Discreet particles up to 5 mm have been recorded, Hellsten (1994). Union Reefs Gold Mine recovers 40 per cent of its bullion production through a gravity circuit, Riches (1997). Brocks Creek ore contains visible coarse gold with gravity bullion production fluctuating between 50 per cent and 65 per cent, depending on the mill feed. Average gravity bullion production from the Brocks Creek Mine is 55 per cent, Wilke (1997). The average gold grain size of Macraes Mine ore is 20 μm with 40 per cent of the gold in sub 10 μm particles. No gravity bullion is produced from the Macraes Mine, O'Keefe (1997). The testwork demonstrated conclusively that it is possible to prepare a representative sample for assay, of a coarse gold ore, when a Keegormill is used to pulverise the sample to a nominal 100 μm particle size (90 per cent passing a 100 μm screen by wet sieving). Both the Mixermill and the Labtechnics LM5 failed to prepare a representative sample, even when ground to a nominal 75 μm particle size.

Jan 1, 1998

By B. H. Kear

Clustering of slip bands in different systems has been observed in both ordered and disordered Cu3Au crystals compressed in the <110> orientation. Certain features of the slip band patterns are explained in terms of reactions between dislocations with Burgers vectors at 120 deg; in a few rare cases, the slip band evidence suggests that the Products of such reactions form diffuse tilt boundaries between the differently slipped regions of the crystal, similar to the known behavior of ionic crystals, but not nearly so well defined. WHEN crystals with orientations favorable for multiple slip undergo plastic deformation, slip may occur in different systems in localized regions, so that clusters of slip bands are developed. This phenomenon has been observed in fee1-4 metals and also in ionic crystals having the sodium chloride structure.5-8 In the ionic crystals, the boundaries formed between the differently slipped regions of the crystal assume characteristic orientations and are associated with macroscopic tilts that are plainly visible on the sides of the crystal. Recently, this interesting feature was explained in terms of the formation of diffuse low-angle boundaries as a result of interactions between families of glide dislocations in the different systems meeting in the boundaries.9 This paper describes an attempt to obtain similar evidence for boundary formation in an fee crystal. The alloy Cu3Au was chosen for the present study simply because this material is currently being used in a general study of differences in deformation behavior of the ordered and disordered phases of this alloy, which will be described elsewhere. EXPERIMENTAL PROCEDURE The two specially oriented compression specimens used in the present study were prepared from a melt-grown single crystal by careful cutting, grinding and polishing. The finished specimens were about 6 mm by 2 mm in cross section by 6 mm tall, with their ends parallel to (101) and sides parallel to (111) and (121); the broad faces of the specimens were made parallel to (711). Both specimens were annealed in an evacuated quartz tube at 850oC for several hours, slowly cooled to 500°c, and then quenched into water in order to obtain the disordered state for the alloy. One of the specimens was partially ordered (with S- 0.8) by reannealing at 350oC for 100 hr. After these annealing treatments, both of the specimens were electropolished. 10 Finally, the specimens were compressed in the [loll orientation and their stress-strain curves were recorded. The deformation was carried out in increments of a few percent strain. At each stage in the deformation the specimens were unloaded, removed from the compression jig, and examined optically for slip bands. Before reloading, the specimens were repolished, so that the observed slip band patterns were characteristic of a particular stage in the deformation. EXPERIMENTAL RESULTS Fig. 1 show!; the stress-strain curves for the ordered and disordered specimens and also indicates the stages 1, 2, and 3 where the deformation was interrupted for examination of slip bands. The curves show marked differences in flow stress and in work hardening rate in the two specimens, as observed by previous workers.11,12 Also, it was found, in agreemement with the observations of Taoka and Sakata,&apos;3 that the plastically deformed disordered alloy showed the characteristic coarse slip bands of alloys, whereas the ordered alloy exhibited a fine slip band structure similar to that of pure metals. Slip Band Observations. In what follows, the description of the slip band patterns, with accom-

Jan 1, 1962

By Matt Bilson, Ritesh Mahajan, Antoni Kuras, Wataru Okada

The Waterview Tunnel comprises twin 2.4 km long 13.1 m internal diameter three lane road tunnels in Auckland, New Zealand. The City Rail Link (CRL) is a 3.45 km long, 6.24 m internal diameter twin rail tunnel underneath Auckland’s city center. This paper presents an overview of the tunnel geometry, segmental lining congurations, geometric constraints, performance criteria and functional reuirements for the large diameter Waterview Tunnels and smaller diameter CRL tunnels. Other key aspects, which include sustainability, innovations, construction performance and practical aspects are discussed and compared. Lessons learnt from these mega tunnelling projects are also presented.

Jun 23, 2024

The control system of a mine winder or other variable speed drive has many component parts that must work together to provide the required functional performance of the machine, together with comprehensive safety features, reliability, maintainability, user-friendliness and efficiency. Modern winders use digital control technology extensively and hence software design is a major part of the overall system. It is not practical to simulate an entire mine winder in a single computer model because of the sheer mathematical complexity of the behaviour of many of the components. However, most component parts can be simulated quite easily, and related parts of the control system software can be simulated. Such simulations allow control software algorithms to be developed and tested in isolation from the real plant. Tests can be performed on the model without fear of injury to personnel or damage to the valuable plant. For example, speed regulator control algorithms and stability settings can be adjusted to and beyond the limits of stable operation, and near optimum settings can be found. This is particularly important, for example, when designing closed loop controls for emergency brake systems. Obviously, care must be taken to ensure that the computer model of the plant is realistic and takes into account as many non-linear features of the real plant as possible. Pure mathematical analysis of some systems is very difficult to perform when non-linear plant behaviour is involved. This paper shares a number of practical simulation experiences performed using commercially available software such as Matlab and Simulink to simulate various parts of the control system of a mine winder or other variable speed drive. Demonstrations of the operation of several different computer models are shown during the presentation of the paper.

Jan 1, 2005

By Arthur L. Walker

DURING my trip around the world last year, covering a total of 45,000 miles, I saw many things of especial interest from an engineering viewpoint. Sailing from New York, I went through the Panama Canal, down along the west coast of South America, then over the Peruvian and Bolivian Uplands; thence to the celebrated copper mines of Chile; across the Andes, to Buenos Aires, then to Rio Janeiro; across the Atlantic to Lisbon, Portugal; through Spain to the Rio Tinto mines; across southern Europe to Italy; thence to Alexandria and Cairo; up the Nile to Assouan, to Palestine through the Suez Canal, Red Sea and across to Bombay; up to the country of the Moghul Emperors; then to Calcutta, from which point I shipped to Singapore, as having crossed the Equator twice, I wished to shake hands with it again; thence to Shanghai and Pekin; up to the Great Wall of China, back to Nanking and up the Yangtse to Hankow; then back and eastward across the Pacific Ocean. The climatic changes were sudden and severe; there was winter where, for me, it should have been summer and vice versa. The weather man was very kind, however, and until I was near the Aleutian Islands there were only three rainy days in a total of 220.

Jan 1, 1924

By C. Vipulanandan

Installation procedure and the quality of the material used in the construction have significant effects on the behavior of the Auger Cast in Place (ACIP) piles. In this study, Installation and curing of a 760 mm (30 in.) diameter and 12 m (39 ft) long ACIP pile with a design capacity of 1140 kN (128 tons) in hard clay was investigated. Construction quality was monitored using the automated monitoring system where the volume of grout pumped and the pressures were monitored with depth. The curing of the pile was monitored using axial vibrating wire strain gages at four levels and lateral vibrating wire strain gages at two levels. The residual strain and temperature profile in the curing pile was monitored over a period of week to determine the appropriate time for load testing the pile. Axial behavior of Auger Cast in Place (ACIP) Piles in hard clay was studied using full scale load test on an instrumented pile. The load-settlement and load transfer relationships of the pile was investigated based on the load test results. Development of skin friction in the load test pile and the reaction pile was also investigated.

By J. S. Orphanos

The requirements for controlling air and stream pollution are a most timely subject for concerned people. The coal industry has taken great measures to reduce pollution. With the use of more efficient scrubbing equipment on their thermal dryers, pollution has been considerably reduced. Furthermore, eliminating thermal drying completely by using centrifugal dryers (Bird screen bowls) to dewater fine coal products and meet consumer specification has completely eliminated air pollution. The coal industry is taking steps to eliminate stream pollution and the hazards created by tailings ponds. These plants are closing their water circuit by recovering all solids in solid-bowl centrifugal equipment. In doing this effectively and economically the water discharged into the streams does not contain any refuse solids. This provides a safe economical method.

Jan 1, 1976