Search Documents

By A. F. Collings

The processing of heavy mineral concentrates can be enhanced by the use of power ultrasound to clean their surfaces of oxidation products and fine coatings, mainly through the large, but very localized forces, produced by cavitation. Results are presented of the application of power ultrasound to remove coatings from the surfaces of mineral sand concentrates in order to improve the sharpness of their high-tension separation and, in some cases, the quality of the low iron components such as zircon. Improvements of 10–15% in recovery and up to 20% in grade compared to unsonicated material were achieved in a single stage laboratory high-tension separation. Cavitation also ensures that a fresh, clean surface is presented to leachants during the leaching of suspended solids. At the same time, the effect of cavitation and the shearing effect of the sound wave passing over the solids ensure that the saturated boundary layer is kept to a minimum if not completely removed. This application of power ultrasound helps to speed up leaching processes as applied to the removal of excess alumino-silicate contaminants in some ilmenite. Keywords: Ultrasound, power ultrasound, heavy minerals, processing.

Jan 1, 2003

By G. E. McClelland

Agglomeration techniques have been successfully applied to commerical heap leach cyanidation operations for the recovery of precious metals from low-grade ores, mine wastes, and tailings. The major parameters important for successful agglomeration pretreatment of these feed materials are discussed. Several commercial agglomeration-heap leaching operations are described. Two of the operations converted from conventional heap leaching to agglomeration-heap leaching after coventional heap leaching proved unsuccessful. Heap performance before and after agglomeration is discussed. A fairly recent operation that began production using agglomeration-heap leaching technology is also described. Two operations that processed milled tailings by agglomeration are discussed. The tailings feeds could not have been economically processed by means other than agglomeration-heap leaching.

Jan 1, 1986

By Joseph Haid, om, Rio Yang, Kelly Fleetwood

Some coal mining operations in the Powder River Basin are currently observing a number of blast holes detonating sympathetically within their cast blasts. Sympathetic detonation can cause poor cast results, high blast vibration levels, excessive back break and fly rock, along with a number of other undesirable blast results. The reduction or the total elimination of blast hole sympathetic detonation is of paramount importance to the coal mining companies operating in the Powder River Basin. This paper describes a systematic approach to prevent cast blast holes from detonating sympathetically through the use of the electronic initiation and expanded blast patterns. In-situ measurements outlined in this paper were recorded from pressure probes, velocity of detonation probes and near field accelerometers, along with digital images generated from a high speed CCD camera. Large diameter angled drill holes were also checked for any measurable amount of deviation by a cable type borehole measurement tool. The field measurements provided the scientific evidence, statistical data, and documentation necessary to develop a sound method or a “road map” that would minimize and in some situations prevent the occurrence of blast hole sympathetic detonation.

Jan 1, 2005

By J. D. Patsey, G. T. Lineberry

Introduction A computer program was developed for analyzing drum-type hoists before modifying an existing system or designing a new one. Its use permits the preliminary evaluation of a system before seeking technical assistance from mine hoist designers and manufacturers. The user-friendly program accepts a variety of data and analyzes hoisting systems for any balance state. The program can be used to calculate skip capacity to yield a desired production rate, solve for drum face width, select a permissible wire rope, estimate total horsepower of the hoist plant, and estimate annual power cost. Whether required for a large mining complex or for a relatively small operation, a hoisting system must be carefully designed to ensure the efficient, reliable, and safe flow of material. Because shaft sinking and hoist installation can total between 2.5% and 3% of the cost of opening a deep mine, proper hoist selection is critical. Today's mining engineer has at his disposal the most powerful design and analytical aid ever, the microcomputer. There is, unfortunately, limited software for the study of hoisting systems, unlike that for other materials handling equipment (Manula and Albert, 1980; Prelaz et al., 1964; Bucklen, 1969; Thompson, 1985). HOIST reduces a time-consuming set of calculations to a concise package of interrelated subprograms. A literature review revealed no common-user programs to analyze hoisting systems, although at least four major hoist designers/manufacturers/installers have their own in-house programs. To provide a tool with which the mining engineer could preliminarily analyze a materials hoisting system or could check the calculations of a hoist contractor, a computer program was developed. HOIST was written in BASIC for the IBM-PC for ease of program adaptation and to encourage field use on compatible systems. Details of program development are omitted, since the basic principles of hoisting analyses are relatively straightforward, simple, and readily accepted (Harmon, 1973; Nordberg, n.d.; Adler, 1957). Program features, intended usage, and benefits of the computerized solution are emphasized over theory development and mathematical rigor. Background The mine hoist system that is selected and installed at a mine is the "lifeline" of that mine, with installations lasting 20 years or more. Thorough study is warranted to ensure that productivity demands are met at a minimum cost per ton. The increased cost of a large, powerful, high-speed hoist must be offset by increased production to justify its selection. To optimize this tradeoff, an extensive hoisting analysis should be performed. The analyses to properly size the skip (or cage), the drum, and the hoist drive are conducive to computerization, permitting rapid evaluation of changeable operating and design parameters, such as velocity, acceleration, state of balance, and productivity demand. The program is particularly useful in conducting sensitivity trials, such as investigation into the effect of change of productivity on skip capacity and on horsepower of the hoist drive. HOIST is currently limited to the study of drum-type hoists with cylindrical drum(s). However, only minor changes to the program would permit analysis of friction hoists and conical drum configurations. Model development and testing The program is based on accepted equations and physical relationships. Examples of manual calculations formed the basis for decision points and program branching. Data is input in the order that it would be needed if the problems were solved manually. The choices are arranged likewise. HOIST was developed in sections, with manual solutions performed to check program logic. The testing became more rigorous as sections were completed. Output from one section becomes input for following sections, as appropriate. The simplified flow diagram of HOIST is given in Fig. 1.

Jan 2, 1987

By K. Bullock, M. Levesque, G. Lyle, D. L. Millar

ABSTRACT The options for reducing the carbon footprint of energy use in mining fall into three categories of activity: i) reducing demand, ii) improving energy utilization, and iii) adopting low carbon energy technologies. In addition to the environmental imperative, the economic case for these activities gains higher priority as the prices of electricity, gas, and liquid fuels increase. Low-carbon, energy-saving technology options that are available to mining industry companies lead to projects with return rates that must compete alongside other capital-intensive projects considered by mining company boards. Energy projects frequently involve longer payback periods and lower rates of return than those of competing bids for capital, such as new mineral property developments. For energy services companies that specialize in the financing, construction, efficient operation, and maintenance of energy projects, the same returns and payback periods can be considered acceptable or even attractive.

Jan 1, 2012

By S Wellink, D Chalmers, D Adermann, C Martin

The practice of recording blasts for quality control purposes has been conducted for several decades. However, at the low frame rates of a standard video camera, essential data is frequently missed as it occurs when the shutter is closed between frames.The use of high-speed video for the research, development and monitoring of the performance of blasting procedures is a well proven but under-utilised practice.The recent development of low cost, easy to use high-speed digital cameras and user friendly software can deliver a capability into mine management as a day-to-day production tool that can greatly improve blasting performance and reduce costs.Digital high-speed video and image analysis software can accurately quantify each blast. Analysis of the images can facilitate the identification of causes of variance from design, geology changes, errors in blast practice and areas of poor performance. The use of high-speed video greatly enhances the audit and review processes so that future blast design can be quickly and appropriately modified to deliver improved blasting performance and reduced costs.The three videos demonstrate the differences between standard video and high-speed video and the detail that can be obtained from them. These videos of open cut blasts can be used to identify blast performance variances. Capturing images at 1000 frames per second allows the analysis on a millisecond timescale where detonator timings, fragmentation, venting, fume generation and flyrock can be accurately identified.CITATION:Adermann, D, Chalmers, D, Martin, C and Wellink, S, 2015. High-speed video – an essential blasting tool, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 471–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A. K. Mishra

The mineral industry is leading towards a technology driven optimization process. Drilling and blasting are such unit operations in a mine, which can alter the balance sheet of the mine if not planned properly. The development, improvement and utilisation of innovative technologies in terms of blast monitoring instruments and explosives technology are important for cost effectiveness and safety of mineral industries. The ever-growing demand of mineral has compelled the industry to adopt mega opencast projects with big equipments. This has necessitated use of few hundred tonnes of explosives in each blast. The bulk delivered fourth generation explosives has solved the problem of explosive loading to a large extent. The priming of bulk delivered explosives in Indian mines uses the conventional PETN/TNT based cast boosters. As the conventional cast booster possess safety problems in terms of handling and use, so Indian Explosives Ltd., has developed an emulsion based cast booster (Powergel Boost).

Jan 1, 2005

By A. P. Fletcher, K. Croteau

The intent of this paper is to cover some aspects of preventive maintenance methods which have come into wider usage in recent years as a means of increasing operating efficiencies. Particular emphasis is placed on lubrication and related servicing.

Jan 1, 1967

By R. J. F. Goodfellow

Many underground projects now include preparation of a Risk Register through planning and design as a tool for project and risk management. There is still significant discussion within the industry as to whether and how to best present the Risk Register through the bidding process and the construction phase of a project. While the ITIG Code of Practice for Risk Management of Tunnel Works recommends this approach of continuity in risk management procedures, it is silent on the specifics of how this should be achieved. This paper will explore the perceived benefits and disbenefit of including the project Risk Register with bid documents; format and content that should be transferred and lessons learned using the case history of bidding and early construction phase of the Bi-County Water Tunnel in Montgomery County, MD

By Jamie Archibald

The Department of Mining Engineering at Queen?s University conducted a study of backfill practices in underground mines across Canada to assess the current state of backfill usage and to overview potential hazards associated with backfill practice, from preparation to transportation to placement. The primary aim of this study was to cover each component of a typical mine backfill system, and to identify potential incidents leading to the disruption of backfilling operations and any associated corrective actions. This paper, Part II of the study, deals with underground operations consisting of backfill transportation and backfill placement. Part I of the study, which deals with surface operations consisting of backfill material supply and backfill plant preparation, is also presented in these proceedings. A review of safety measures associated with current backfill operations and recommendations for procedures of best practice that should be implemented to reduce fill-related hazards in all mine backfill workplace environments are presented. In general it has been found that system failures normally lead only to minor losses to the operations.

May 1, 2009

The purpose of this paper is to discuss briefly the problems encountered in designing and sinking No 7 shaft, and to present the methods employed in the operation.The illustrations accompanying the paper show the details of the construction of the equipment used in completing No 7 shaft, consequently the descriptions appearing in the text are brief outlines only. Mineral leases Nos 7 and 8, held by the Broken Hill South Limited, comprise an area of 69.5 acres. The length of the holding is approximately 2500 ft.The western orebodies, which are the main producing masses, enter the property at the northern bonndary. Generally, the dip of the orebody is to the west, and the pitch to the south, but local variations occur and even a reversal of pitch has been noticed. The angle of dip is approximately 70 degrees and the angle of pitch 45 degrees.

Jan 1, 1932

By S Christensen

In August 2001 the Minister for Conservation declined an application by GRD Macraes for an access arrangement to enable work at the Globe Progress Mine near Reefton. In her decision, Ms Lee said:æI have considered whether potential compensation and the proposed safeguards against some of the adverse effects are sufficient to outweigh my concerns as to the loss of conservation values, consistency with the objectives of the Conservation Act, the purposes for which the land is held by the Crown and, to a lesser extent, the North Westland Regional Management Plan. I do not think they are sufficient. To my mind, my concerns as to the consistency with the objectives of the Conservation Act, the purposes for which the land is held and the loss of some conservation values in particular, outweigh any potential compensation and possible mitigation of adverse effects.Æ Commenting on the MinisterÆs decision Guy Salmon of the Ecological Foundation stated that the Minister should have invited the applicant to provide a 10 000 hectare pest-free wildlife sanctuary as part of the æpriceÆ for obtaining that access. However,æfor many people of green persuasion, it has become fashionable to say no every timeàthose who really have the well-being of the environment at heart, will want to look carefully at the bigger picture of environmental restoration needsàThe deciding criterion: the mining company should show that its involvement on conservation land would produce a net conservation gain. That is a criterion that creates the right incentives for win-win-win solutions on conservation land.ÆThis paper considers whether the concept of off site mitigation is one which fits within the current legal regime. Two questions arise:Can such mitigation/compensation be legally considered in access arrangements or required as a condition of resource consents? Is this a realistic option for industry to be pursuing?

Jan 1, 2002

[Abad. Leopoldo F., Min. Engr., Div. of Mines, Bureau of Science Manila, P. 1. '28 Abadilla, Quirico A., Geol., Lago Pet. Corp Box 172, Maracaibo, Venezuela. '20 Abarquez, Ramon F., Met., Bureau of Science Manila, P. I. '24 Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, Ohio. '21 Abbott, A. N., Mines Supt.. Mazapil Copper Co,, Ltd Concepcion del Oro, Zac,, Mexico. '28 Abbott, Clarence E., Mgr,, Mines & Quarries, Tenn, Coal, Iron & R. R. Co., 1242 Brown Marx Bldg,, Birmingham, Ala. '04]

Jan 1, 1928

NEW YORK SECTION J. E. Johnson, Jr., Chairman Edgar Rickard, Vice Chairman. D. M. Liddell, Secretary, 7 Wall St., New York, N.Y. C. A. Bohn, Treasurer John V. N. Dorr Lewis W. Francis. The annual meeting of the New York Section was held on Wednesday, June 6, with about 40 members in attendance. The treasurer re a brief summary of-the financial statement for the year, and the secretary's report was read. These reports were ordered placed on file together with the report of the auditors for the two previous years.

Jan 8, 1917

By Douglas J. Lacke

1974 marked the start of a new era for Climax Molybdenum Co., a division of AMAX, with the initiation of an open pit operation above the existing successful underground block panel caving mine. A number of problems posed a challenge to the Climax open pit. Highly fractured rock, old mine workings, permafrost, and more than 7.6 m/a (300") of snowfall forced changes in normal operations. Final pit wall design was altered. Production bench heights were lessened due to old workings. These and other modifications contribute to a highly successful open pit operation.

Jan 1, 1981

By K Faure

At Sams Creek a gold-bearing, peralkaline granite pophyry dyke intrudes Ordovician-Silurian metapelite and quartzite. The granite porphyry dyke has a thickness of up to 40 m, extends discontinuously for about 8 km, and intrudes thin lamprophyre dykes along its contacts. The granite dyke and gold-bearing sulphide and quartz-siderite veins within it have been deformed and recrystallised during several phases of folding, the youngest of which is Early Cretaceous.   The unaltered granite porphyry is composed of phenocrysts of perthite, arfvedsonite, aegerine and quartz in a groundmass of the same minerals, with accessory ilmenite, rutile and fluorite. K-Ar dates of amphibole from the granite gave ages of 226 and 246 Ma, but these ages may be a minimum due to resetting during the thermal and deformation events that have affected the area. Unpublished Ar-Ar data on amphibole from the granite show disturbed spectra with high temperature steps around 300-315 Ma, which is consistent with the age of A-type granites in the Buller region. Further age dating of primary and hydrothermal minerals in the granite is continuing. At least three stages of hydrothermal alteration have been identified in the granite. Stage I alteration is characterised by high fO2 magnetite-siderite ¦ biotite, which is cut by thin quartz-pyrite veinlets (Stage II). These are cut by Stage III sulphide, quartz and siderite veins, and pervasive silicification represented by quartz-perthite-albite-rutile ¦ pyrite-siderite-sericite assemblages overprints the earlier alteration stages. Lamprophyre is altered to a siderite-chlorite-sericite assemblage. Stage III sulphide veins are composed of arsenopyrite + pyrite ¦ gold ¦ galena ¦ sphalerite ¦ chalcopyrite ¦ pyrrhotite ¦ graphite, deposited by low fO2 H2S fluids. The gold contains 18-30 wt% Ag and up to 1 wt% Bi. Temperature of vein formation was estimated from vein quartz fluid inclusion homogenisation temperatures (Th 260-355oC, average 330oC), arsenopyrite-sphalerite thermometry (310-365oC) and quartz-albite stable isotope thermometry (340oC). The altered granite and the veins have been deformed, and recrystallised and competent sulphide minerals are fractured and brecciated. Alteration and mineralisation are confined to the granite porphyry and adjacent lamprophyre.

Jan 1, 2004

By Kevin A. Foo, Murray D. Bath, John H. Canterford, Arnaldo Ismay

There is no doubt that the dominant future source of gold will be the so-called refractory ores, especially those with gold in a pyrite/arsenopyrite matrix. Minproc Engineers is taking an active role in establishing detailed design criteria for a number of apparently competing processes. This involves generating a detailed understanding of the metallurgy involved, systematic pilot plant testing, and the application of advanced engineering technologies. This presentation outlines the approach adopted by Minproc as well as the design criteria for several current projects.

Jan 1, 1989

By M. Zaske, E. R. Mortensen

"As mine operators continuously look for ways to improve functionality and increase the capacity of their facilities, existing process equipment is often pushed to and past its designed limitations. As a result, equipment manufacturers are asked for economical solutions to meet redefined processing needs. Newmont Mining in Nevada was faced with such a need in its carbon-in-leach (CIL) train. In a collaborative effort between Newmont and Derrick Corp., tests were conceived to assess the viability of drop-in replacement screens using a three-dimensional screen panel. The synthetic pyramid screen panel was designed to increase flux while maintaining the existing equipment footprint. The test is the end result of an ongoing research and development project that Derrick undertook in an effort to refine and upgrade its urethane screening media. The application of this new screening media is presented for this CIL application along with future plans to implement the technology in trash, safety, carbon dewatering, carbon sizing and other scalping applications.In spring 2014, Process Machinery Associates (PMA), Derrick’s local area representative, met with Newmont to discuss the operation of the in tank screens in the CIL train at Twin Creeks, near Golconda, NV. The process was originally designed for about 12+ kt/d (13,000+ stpd) but the throughput has been steadily rising since the plant was commissioned. Newmont now requires 14.5 kt/d (16,000 stpd) to be processed. The original screens were running at their maximum capacity, and Newmont required additional screening capacity to continue the upward trend in production.Physical separation by use of screening is one of mineral processing’s oldest methods. Screening media can be prone to blinding and pegging, and the necessary support structures required for finer apertures result in smaller open areas. Therefore, more screening area generally requires larger panels and, thus, larger machines, screening media that does not blind or a combination of both.In an effort to avoid larger machines, Derrick had been working on a revolutionary threedimensional panel that would add nonblinding screen area in the same footprint of an existing machine. Alpha testing of the new screen panels began at Newmont Mill 2/5 in July of 2013. It was still occurring when PMA approached Twin Creeks about beta testing a refined machine and pyramid panel. After presenting the initial results, Twin Creeks determined that an upgraded machine and pyramid panels would be a possible solution to meet production needs. The testing of a machine eliminated the risk of capital costs to Newmont and provided Derrick the opportunity to obtain additional data."

Jan 1, 2015

By S. K. Gilman, V. E. Hugo

A common problem encountered in the mineral sands industry is that the mineralogical measurements used in defining the resource are not readily converted to metallurgical recoveries, which are used to predict the quantity of the final products. The problem stems from the different objectives of the exploration and metallurgical assessment programmes, and is often compounded by the use of different laboratory techniques and mineral definitions. Common mistakes include the misapplication of routine analysis, incorrect interpretation of mineral recovery, the confusion of mineral recovery with product yield and inconsistent definition of the same mineral. Experience has shown that unless these potential mistakes are identified, the measurement techniques used during exploration and metallurgical assessment are not compatible, often resulting in large errors in the prediction of mineral production. There are no easy solutions to the problem, as there is no universal assay technique which can cost effectively characterize all the mineral sands resources. The recommended course of action will therefore require several iterations to optimize the assay technique to suit the resource. Fundamental to the success of the measurement technique is the understanding of the mineralogy, its behaviour during mineral processing and the quality requirements for the final products.

Jan 1, 2003

By S Arai

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Podiform chromitites are commonly found in the Moho transition zone to the mantle section of ophiolites, but have been very rarely found from the current ocean floor, even though some ophiolites are considered as a slice of oceanic lithosphere. One of the factors controlling podiform chromitite formation is the chemistry of host mantle peridotite; an intermediately refractory harzburgite is the optimum host for chromitites. This harzburgite represents the most common lithology of the oceanic lithosphere, where the peridotite-melt reaction, which is another condition, is possibly common there. The oceanic lithosphere mantle is thus a good host for podiform chromitites. The apparent rarity of documented oceanic chromitites is solely due to under-sampling of mantle materials from the fast-spreading ridge and the segment centre of slow-spreading ridges. Some ophiolitic chromitites formed not from genuine mid-ocean-ridge basalt (MORB) but from wet MORB due to the situation of typical ophiolites, which formed not at ordinary mid-ocean ridges but at supra-subduction zone spreading centres.CITATION:Arai, S, 2015. Podiform chromitites do form beneath mid-ocean ridges , in Proceedings PACRIM 2015 Congress, pp 465–468 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015