Search Documents

By Ryan W. Ulansky

This paper presents the conceptual design of a magnetically-levitated skip for use in an underground mine. A skip is used to move rock from an underground mine to its surface processing facility. Conventionally the skip is raised and lowered by cables, similar to an elevator. In a magnetically-levitated skip, the cable is replaced with a linear induction or synchronous motor to provide propulsion and levitation. Removal of the cables in a magnetically-levitated skip provides many advantages over a conventional system including the ability: to negotiate corners, to travel vertically in the shaft as well as horizontally to the mining face, and to move a very large volume of material using multiple skips in a small shaft. A magnetically-levitated skip is a safer, more environmentally-friendly, productive alternative to conventional skipping. It has the further advantage to decrease haulage distances for underground vehicles.

May 1, 2002

By George E. Aiken

Subzero temperatures of the Arctic pose some critical engineering problems for the developer and operator of open pit mines. Undoubtedly, the single most troublesome manifestation of this climate is permafrost. Underlying about 20% of the world's land area and 85% of the state of Alaska, permafrost has not only made its impact on building construction and mine excavation, but has created a legitimate threat to the delicate balance of nature existing within the Arctic environment. The recognition of permafrost areas by geomorphology and an understanding of its other complex developmental factors are the basis for two major concepts in building construction. The active method involves the eventual thawing of the complete permafrost section and is only useful in shallow areas. However, in some areas of coarse, well-drained material, vegetation may be stripped well ahead of construction and shallow permafrost allowed to method, leaves the perenially frozen ground undisturbed and is to be preferred. In selecting construction sites aerial photos may clearly reveal typical permafrost features.

Jan 5, 1972

By Takashi Araki

In this work, we have elucidated the two-step oxidative reaction mechanism of 2,4,5-trichlorophenol by adsorbing oxygen atom for oxidative decomposition reaction of 2,4,5-trichlorophenol on oxide catalyst surface using ab initio molecular orbital calculation. In the first oxidation, total energies of reaction products have been shown extremely stabilized at all oxidation positions. This reaction occurs due to charge transfer from benzene ring to adsorbing oxygen atom. As a result, 1£ bonding of benzene ring are weakened. However, the benzene ring of 2,4,5-trichlorophenol does not perform cleavage reaction. In the second oxidation, the benzene ring of2,4,5-trichlorophenol can perform cleavage reaction, since the second oxidation obtains larger stabilized energies than the first oxidation.

Jan 1, 2003

By R. R. Hart, B. C. Wonsiewicz, G. Y. Chin

In recent years there has been increased miniaturization of electromechanical devices to keep pace with current trends toward smaller electronic components. A major problem facing the designer, however, is the higher stresses encountered by the material as a result of shorter springs. Hence an improvement in the elastic limit, as approximated by the 0.01 pct offset yield strength, would be highly desirable. An increase of 25 pct in the yield strength, for example, will permit a 20 pct reduction in both the length and thickness of a cantilever-type spring while maintaining the same compliance. One technique of improving the yield strength that has received little commercial attention is crystal-lographic texture strengthening.1,2 Texture strengthening is expected to be most beneficial in materials of hcp structure, but considerable gain can also be expected in cubic materials. A wire with a (111) fiber texture, for example, is expected to be 20 pct stronger than randomly oriented material, and 50 pct stronger than wire with a (100) fiber texture.293 For sheet specimens with a {110}(112) texture, characteristic of many heavily rolled fcc alloys, the (111) transverse direction is expected to be the maximum yield strength direction, about 20 pct higher than that in the (112) rolling direction.' In addition, the (111) direction is the direction of maximum modulus of elasticity for most cubic alloys. A large value of the elastic modulus could be desirable in designs where stiffer springs are required. To test the above idea, a 0.090 in. (-2.3 mm) thick commercial grade A (5 pct Sn) phosphor bronze sheet, a widely-used material for relay springs, was rolled from the spring-tempered condition (60.5 pct reduction) to various additional reductions up to a total reduction of 95 pct. Subsequently, additional material was obtained with a total thickness reduction of 97.3 pct Standard tensile specimens were prepared from the sheet material with the tensile axis parallel to and at 90 deg to the rolling direction. Tests were run on an Instron testing machine at a strain rate of about 0.050 min-l. Textures were determined by the use of the reflection pole-figure technique. Data were obtained using nickel-filtered CuKa radiation and with the aid of a Siemens pole figure goniometer. The X-ray pole figure studies show an incrzasing development of the texture toward the {110}(112) ideal

Jan 1, 1970

The morning session opened at 9:00 a.m. and was presided over by George A! Nugent, President, Sheridan Wyoming Coal Company, Sheridan, Wyoming. The first speaker was Joseph E. Zatek, Product Specialist, Portable Instruments; Mine Safety Appliances Company, Pitts¬burgh, Pennsylvania. His presentation was illustrated by slides and subject, "Problems of Noise as Applied to Coal Mining." (See Index for printed text of Mr. Zatek's paper.) Mr. Zatek has been with Mine Safety Appliances Company for the, past 14 years) Prior to going with M.S.A. he was Indus!, trial Hygienist for Pennsylvania Department of Health, a position he held for 10 years He attended the University of Pittsburgh, Pittsburgh, Pennsylvania, and graduated with a B.S. degree in Chemical Engineering. He is a member of Air Pollution Control Association, American Society of Safety Engineers, Instrument Society of America and the American Industrial Hygiene Association. He is certified by the American,' Board of Industrial Hygiene in Compre¬hensive Practice of Industrial Hygiene and also by the Bureau of Mines to be an Instructor in Noise Measurement and Control.

Jan 1, 1971

By Lawrence B. Wright, Lester G. Morrell

On the steep slopes of the Kootenays, 15 to 20 miles south of Nelson, B. C., are a number of ore occurrences (Fig. 1). One that has many features of mining and geological interest is the Ymir Yankee Girl Gold Mines Limited. Discovery of this property was made in 1899 at an outcrop on the hillside, some 2500 ft. above the village of Ymir. This proved to be a branch vein 20 ft. long leading to two main veins, the Yankee Girl and the Spur (Fig. 5). The ore pattern as now delimited shows a remarkable increase in ore area with depth below the outcrop. This recent development is of interest particularly in view of the fact that the property was nearly condemned, professionally. Another interesting feature, which has a bearing upon its history, is the persistent excess of tonnage produced from period to period over visible reserves. This is not ascribed to lagging mine development, but to detailed vein characteristics, which we will endeavor to make clear by giving a description of the veins and their surroundings. HISTORY AND PRODUCTION Little interest_was_evidenced-in this-distriet until the building of the railway in 1893 provided easy access and the discovery of the Ymir mine in 1896 attracted attention. As a result, the Ymir Yankee Girl group of claims was staked in October 1899. In 1907, an American syndicate took over the property and subsequently extended the 50-ft. drift and opened the present 400 and 540-ft. levels. In 1908, the Syndicate, without recording any shipments in the meantime, dropped its lease, which was taken up by H. L. Rogers, who bonded the Yankee Girl group. Rogers shipped 2622 tons of ore, mainly from the uppermost stope in the mine, which is reported to have yielded

Jan 1, 1940

By Lawrence B. Wright, Lester G. Morrell

On the steep slopes of the Kootenays, 15 to 20 miles south of Nelson, B. C., are a number of ore occurrences (Fig. 1). One that has many features of mining and geological interest is the Ymir Yankee Girl Gold Mines Limited. Discovery of this property was made in 1899 at an outcrop on the hillside, some 2500 ft. above the village of Ymir. This proved to be a branch vein 20 ft. long leading to two main veins, the Yankee Girl and the Spur (Fig. 5). The ore pattern as now delimited shows a remarkable increase in ore area with depth below the outcrop. This recent development is of interest particularly in view of the fact that the property was nearly condemned, professionally. Another interesting feature, which has a bearing upon its history, is the persistent excess of tonnage produced from period to period over visible reserves. This is not ascribed to lagging mine development, but to detailed vein characteristics, which we will endeavor to make clear by giving a description of the veins and their surroundings. HISTORY AND PRODUCTION Little interest_was_evidenced-in this-distriet until the building of the railway in 1893 provided easy access and the discovery of the Ymir mine in 1896 attracted attention. As a result, the Ymir Yankee Girl group of claims was staked in October 1899. In 1907, an American syndicate took over the property and subsequently extended the 50-ft. drift and opened the present 400 and 540-ft. levels. In 1908, the Syndicate, without recording any shipments in the meantime, dropped its lease, which was taken up by H. L. Rogers, who bonded the Yankee Girl group. Rogers shipped 2622 tons of ore, mainly from the uppermost stope in the mine, which is reported to have yielded

Jan 1, 1940

By Gökhan Hardal, Berat Yüksel Price

Nickel manganite based negative temperature coefficient (NTC) thermistors have good temperature sensor characteristics and electrical stability for temperature measurement applications. In this study, the electrical and microstructural properties of Ni0.5Co0.5Cu0.3Zn0.3Mn1.4O4 NTC thermistor were investigated. The samples were fabricated by the conventional solid-state reaction method. The powders were calcinated at 900 °C for 2 h and the samples were sintered at 1200 and 1300 °C for 5 h in air. The bulk density of samples was 5.07 and 4.96 g/cm3, respectively. The microstructure of samples was observed using a scanning electron microscope. The electrical resistance was measured in a temperature programmable furnace between 25 and 85 °C. The electrical resistivity of the Ni0.5Co0.5Cu0.3Zn0.3Mn1.4O4 sample increased from 52 Ω cm to 95 Ω cm when the sintering temperature increased from 1200 to 1300 °C. The material constant “B”, sensitivity coefficient “α” and activation energy “Ea” values were also calculated for the NTC thermistors.

Mar 1, 2017

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By R. D. Alorro, B. Tadesse, E. Aghaei

Cinnabar (HgS) and native mercury (Hg) are the most common naturally occurring forms of mercury found in most gold ores subsequently released into the environment during processing. Mercury and its compounds are extremely toxic and recognised as serious health and environmental hazards. This research investigates the possibility of mercury (Hg) removal from waste solutions from gold processing using iron-aluminium (Fe-Al) bimetallic particles. The synthesis of Fe-Al bimetallic particles using zero-valent aluminium and ferric chloride as precursors were performed following the optimisation of influencing factors. The presence of both metals in the prepared bimetals was confirmed by XRD analysis. The experiments for mercury removal by bimetals were designed using the central composite design and Minitab software based on two variables including contact time and adsorbent dosage. The best result of Hg(II) removal (>90%) was achieved using 4 g/L bimetals and contact time of 75 min. However, the statistical analysis of results indicated that these parameters have only a minor contribution to the removal of Hg(II) by Fe-Al bimetals. Higher bimetal dosage and contact time resulted in a higher Fe dissolution from the Al surface which can be attributed to the presence of nitrate (# $) ions in the solution. However, adding 0.1 M NaCl to the Hg solution had a positive impact on Hg removal by improving the conductivity and electron transfer within the solution. The Fe-Al bimetallic particles are promising substances for further testing of Hg removal from gold processing waste solutions with different conditions and constituents. Keywords: Mercury removal, gold processing, Fe-Al bimetals, optimisation

Jan 1, 2020

By Betty J. Laswell, Gerald W. Laswell

Rotary drilling in modern open-pit mining is usually considered the lead phase which not only establishes the production rates but frequently limits them. From this viewpoint alone, the drilling phase must be maximized. The drill phase is the step that permits all the other operational phases to function within their design limits. This means that, in most cases, the drill is literally run to destruction to ensure that the shovel will be able to smoothly and consistently load a manageably size muck, the haul trucks can carry a balanced load without having a boulder dropped through the bed, and the crusher can devour constant rock size.

Jan 8, 1978

In 1988, at the request of members of the Society for Mining, Metallurgy, and Exploration (SME) Inc., the president of SME formed Working Party No. 79, Ore Reserve Definition. Its mission was to develop guidelines for the public reporting of exploration information, resources and reserves. These guidelines were published in the April 1991 issue of Mining Engineering (pp. 379-384), and as a document entitled “A Guide for Reporting Exploration Information, Resources, and Reserves” in January 1992. Work continued on an ad-hoc basis until 1996. Working Party No. 79 was then renamed the SME Committee on Resources and Reserves and became a standing committee.

Jan 1, 1999

By A. L. Frank, Benton

INTRODUCTION The selective sensitivity of plastic nuclear track detectors (PNTD's) to low energy 4He particles in an environment which also contains gamma and beta radiations has made these detectors prime candidates for the dosimetric measurement of the concentrations of radon and its daughter products in mine air. Their passive, integrating mode of measurement, small size, low weight and inexpensiveness are attractive characteristics for large scale personnel dosimetry. The detectors can be used in either active or passive dosimeters. In active devices, the PNTD is placed in close proximity to a sampling filter. The filter collects, from a calibrated air flow, all the daughter nuclei which are in suspension. As the daughter nuclei pass through the decay chain, through 214Po, a fraction of the 4He particles emitted are registered as latent tracks in the plastic. In passive devices, the PNTD is placed in direct contact with the ambient air containing the radio-nuclei concentrations to be determined. The active dosimeters have the advantage of excellent sensitivity, and the measured track densities yield very close approximations to accumulated Working Level (WL)** exposures. They have the disadvantage that the simplicity of the passive PNTD is lost, since a battery-driven constant flow-rate air pump is a necessity. The passive dosimeters are simple in construction and use, but they have the disadvantage that WL exposures are not directly measured and certain assumptions concerning radon and daughter equilibrium conditions must be made in determining WL exposures from the measured track densities. Also the sensitivities, in track densities per Working Level Hour (WLH) exposure, are much less than for active dosimeters. Dosimeters of both types have been investigated. Passive devices have been tested extensively both in the laboratory and in mines. Active devices have been laboratory tested. In our earlier measurements, cellulose nitrate plastic detectors were used exclusively, since this material had the highest sensitivity of the PNTD's then in use. When the properties of CR-39 plastic were discovered (Cartwright, 1978; Cassou and Benton, 1978), this material was used, where possible, to take advantage of its superior sensitivity. The results of our earlier work have previously been published (Frank and Benton, 1977). * Research sponsored by the Bureau of Mines, U.S. Department of Interior, under Contract No. JO-188003. ** A Working Level is defined as any combination of the short-lived radon daughters containing 1.3 x 105 MeV of potential 4He-particle energy per liter of ambient air. PASSIVE DOSIMETRY In the earliest testing of PNTD's for passive WL dosimetry, a single strip of cellulose nitrate plastic was used to determine the total cumulative 4He-particle activity in the air of simulated uranium mine and uranium mine environments (Rock, 1968; Rock [et al], 1969; White, 1969). The measurements yielded a close relationship between track densities and WL exposures in a controlled, static environment, but poor accuracy in the active mine tests. It was assumed that equilibrium differences contributed largely to the variations found. The response of PNTD's to airborne 4He-particle emitters, derived by Lovett (1969), demonstrated that detectors such as cellulose nitrate, which has a sensitivity cutoff at 4He-particle energies below the emission energies of radon and its daughters, are equally sensitive to the activity concentrations of radon, 218po(RaA) and 214Po(RaC'). Since radon does not contribute to WL as it is defined, and since, under normal ventilated uranium mine conditions, the radon activity constitutes about 40% to 70% of the total 4He-particle activity, the WL exposures calculated from measured track densities are very sensitive to the particular radon daughter equilibrium conditions. Also, the detector does not weight the individual daughter activities in proportion to their importance to WL. The equation for WL is WL = 0.00103C2 + 0.00507C3 + 0.00373C4 (1) where C2, C3 and C4 are the activity concentrations of RaA, RaB and RaC-C', respectively, in pCi/[L]. The detector leaves C3 unmeasured and weights C2 and C4, equally. [This problem has been approached by Domanski et al (1975, 1979), for some non-uranium mines, by measuring equilibrium conditions throughout the mines to determine a mean value for A, the inverse of the Working Level Ratio (WLR = 100 WL where C1 is the activity of radon-222 in pCi/[L].) The distribution of values allowed Domanski to determine probable errors in calculating WL exposures from track densities. However, measurements of equilibrium conditions in U.S. uranium mines (Breslin et al, 1969; Holub and Droullard, 1978) indicate that this method would not be accurate enough for uranium miner personal dosimetry.] A two-element dosimeter was designed at our laboratory to compensate for equilibrium variations. The first element is a radon detector; the second is a detector for the total 4He-particle activity in the ambient air, just as in the single element dosimeters cited above. The addition of the radon detector allows the equilibrium conditions for the individual nuclei to be determined, given certain assumptions concerning the interrelationships between the nuclei concentrations in mine air. The two detectors and the problems involved in calculating WL exposures from their measurements are discussed below.

Jan 1, 1981

By Goro Shimaoka, Kichizo Niwa

IN the past, the crystalline states of graphite in cast iron have been studied by many investigators. Recently several authors 1-4 have published interesting information on the crystal texture of the individual graphite grain, especially spherulites in nodular cast iron. In regard to the crystal structure of graphite, Lipson and Stokes0 howed by powder X-ray analysis that most of the crystals contain about 14 pct rhombohedra1 structure (ß-form) which differs from the hexagonal structure (a-form) in the sequence of layer stacking. Hoerni6 onfirmed the existence of the ß-form in a single crystal with electron diffraction by Kossel-Moellenstedt's method. Furthermore, Hoerni and Weigle7 found extra reflections in electron diffraction patterns, which are given by a unit cell twice as large as the usual one in the basal plane. Recently, Lukeshs observed graphite twinning and satellite reflections in his X-ray work and considered them as evidence for the existence of an orthorhombic superstructure. Owen and Street" and Matuyama" studied the structures of graphite crystals in several types of cast iron, using the X-ray powder method, and they showed that the graphite crystal contains a certain amount of the ß-form, an amount which varies with the sources of the cast iron used. The present study was made in order to secure structural information on graphitization in cast iron. Electron diffraction studies on the structure of single graphite flakes segregated from molten carbon or silicon-rich iron at 1200" to 1500°C are reported. Experimental Honkeiko pig iron (4.05 pct C, 1.59 pct Si, and 0.65 pct Mn) was used as the solvent of carbon or silicon. The pig iron was melted in an open furnace and a small quantity of metallic silicon was added to the melt at 1300°C. The melt was heated to 150O°C, and then retort black carbon or metallic silicon was added little by little. The components added to the bath contained approximately 5.0 pct C and 2.0 pct Si in the carbon-rich material, and 3.8 pct C and 5.4 pct Si in the silicon-rich iron. These two types were held at 1500°C and then cooled without graphitizing by cutting the heat sup-

Jan 1, 1958

By R. S. Handy

AT THE TIME of my first visit to Bolivia in 1927 the tin-mining industry was prosperous, the tin price at London being more than £300 per long ton of tin, and the operators were making every effort to bring their plants up to the very highest point of capacity as well as of efficiency. Any device or piece of equipment or method that gave promise of increasing production was welcomed regardless of the cost, and the plants were being modernized as rapidly as human ingenuity could make it possible. At the time of my second visit in 1932, however, conditions had changed materially. The price of tin had fallen to a little over £100 but costs had not decreased anywhere in proportion and operators were at their wit's end to cut the operating losses that were everywhere prevalent. Charles L. Bradbury, manager of the Empresa Minera de Huanuni, at Huanuni, Bolivia, had been recently called from Mexico to make all analysis of the situation and to attempt to work out a remedy for the economic conditions that threatened to close the mine. His analysis brought out the following points:

Jan 1, 1938

By Edmund Davenport

THE specific aim of this work has been to study certain forms of internal deterioration which occur in tungsten filaments when subjected to high temperatures under various conditions, and to determine the cause of such deterioration. This would naturally lead to a consideration of methods of control or means of prevention of the phenomena. The deterioration was first noticed as a peculiar condition in the grain boundaries of certain tungsten filaments which had been burned? for long periods in lamps. In these cases it was noted that the grain boundaries contained a number of minute black dots which were at first thought to be non-metallic inclusions. It was demonstrated later that these dots or pits, as they were designated, could be readily produced by burning filaments in an atmosphere of flowing hydrogen. This method was convenient and adequate for the purpose, and was adopted for most of the work discussed in this paper. The evidence accumulated to date indicates that these pits are actually small voids between the grains. The purpose of this paper is to present- the information on this interesting subject gathered during a period of about 3 years. As applied to tungsten, the subject appears to be of considerable importance, experience having shown that this pitting ?is frequently associated with poor performance of filaments in lamps. The question has arisen as to whether these intergranular pits are peculiar to tungsten, or if they occur in all metals. If they are found iii all metals, the facts will be of considerable theoretical interest, as the material at the grain boundary plays an important part in most of the current theories of the properties of metals and alloys.

Jan 1, 1927

By James C. Foley

In-situ characterizations of green state part density and sintering state have long been desired in the powder metal community. Recent advances in non-contact electromagnetic acoustic transducer (EMAT) technology have enabled in-situ monitoring of acoustic amplitude and velocity as sintering proceeds. Samples were made from elemental powders of Al (99.99%), Al (99.7%), Ag, (99.99%), Cu (99.99%) and Fe (99.9%). The powders were pressed in a uniaxial die and examined with acoustic waves for changes in velocity and amplitude during sintering. The changes in acoustic properties were correlated with mechanical properties. Evolution of a series of reverberating echoes during sintering is shown to provide information on the state of sintering, changes in sintering kinetics as well as having the potential for detection of interior flaws.

Jan 1, 2001

By R. W. Kewish

The preparation of massive uranium metal containing very low concentrations of a number of light elements by bomb reduction of UF4, with calcium is described. Details of procedures are given for preparing high-purity ingredients for the bomb reduction. The as-reduced uranium metal contained, on the average, less than the following amounts of light element impurities, in ppm: Li, 0.1; Be, 0.1; B, 0.1; C, 25; 0, 70; Na, 1; Mg, 3; Al, 2; and Si, 7. Other impurities for which the metal was examined averaged, in ppm: Ca, < 10; V, < 10; Cr, 2; Mn, 6; Fe, 50; Co, < 5; Ni, 8; and Cu, 1. THE preparation of very high-purity uranium metal in massive form for research purposes is of great importance. Recently the kilogram-scale preparation of uranium metal containing less than 70 ppm of detected impurities was accomplished by Blumen-thal and coworkers by vacuum remelting of high-purity crystals of uranium obtained by fused salt electrolysis.1"3 Albert and coworkers4 have reported successful experiments in lowering the concentrations of certain impurity elements in uranium, notably iron, to a few ppm by the zone-melting method. The present paper describes the preparation of high-purity massive uranium metal by the bomb reduction of UF4, with calcium. Early in 1951 a program was undertaken at the Los Alamos Scientific Laboratory to prepare uranium metal of very high purity with respect to a number of the light elements. The methods considered for this purpose were 1) bomb reduction of a uranium halide with calcium, 2) electrolysis of fused salts, and 3) hot wire decomposition of UI4, The first of these processes had been used extensively at Los Alamos since 1943 (and still is used) for the production of uranium metal.5 In considering the three processes it was evident that either of the last two would require an extensive development program with no certainty of success. On the other hand, a study of available data showed that uranium metal of very high purity with respect to some light elements had occasionally been made in routine processing by the first method. It was therefore decided that an intensive study of the bomb-reduction process would be made to see if it could be improved to yield uranium metal with very low concentrations of light elements. DEVELOPMENT OF PROCEDURES The bomb-reduction process used at Los Alamos consists of reducing UF4 with calcium, using iodine as a booster. The reaction is carried out in a magnesium-oxide crucible enclosed in a steel bomb. Argon is used in the bomb to avoid objectionable side reactions which would occur in the presence of air. All ingredients for this bomb-reduction process were examined as possible sources of light elements. It was known that high-purity UF4 was required. The calcium used in the reductions was a source of carbon and magnesium. The magnesium-oxide crucibles were sources of boron, silicon, and magnesium. The iodine did not appear to be a source of any impurities. Pure UF4- The UF4 for bomb reduction is prepared from U3O3 , by successive reduction to UO2, with hydrogen and hydrofluorination of the UO2, with anhydrous HF. Since it was known that no impurities were normally introduced during the gas-solid reactions, effort was directed toward the preparation of high-purity U3O3. Of the many possible procedures for the purification of uranium solutions the following were investigated: 1) Precipitation of uranium peroxide. (Two procedures were tried. The first consisted of simultaneously adding hydrogen-peroxide and ammonium-hydroxide solutions to a uranyl-nitrate solution, containing citric and malonic acids, at such relative rates that precipitation was carried out at a constant pH of 1.5 The second consisted of simultaneously adding uranyl-nitrate, ammonium-hydroxide, and hydrogen-peroxide solutions to an aqueous solution

Jan 1, 1960

By D. Hulse

"The science of “optimal economic pit design” has been highly refined in the last decades. Even with the proliferation of optimizing and heuristic algorithms exploiting ever faster computers, the most common input is a single block model and a single set of cost assumptions, each of which is an estimate and prone to errors. An analysis of price assumptions produces a suite of nested economic shells, each with its own quantities of ore, waste, grade, and profit, but due to irregularities in the mineralized body, the growth of these shells can be erratic. To control the impact of the errors of the model and cost assumptions when choosing the pit shell for design, graphs of pit shells characteristics, such as stripping ratio, cost per unit of product and profit/ton, can be analyzed to consider points with higher stability, or robust pits. Selection of robust shells for a pit limit and for push backs can help to understand the impact to profit and risk. The robust shells also guide the preferred solution sets for final pit and cutoff optimization. INTRODUCTION “An open pit mining operation can be viewed as a process by which the open surface of a mine is continuously deformed. The planning of a mining program involves the design of the final shape of this open surface.” Optimum Design of Open-Pit Mines, Lerchs, H. and Grossmann, I. Transactions C.I.M. Volume LXVIII 1965. Traditionally an analysis of economic pit shells and sensitivity was performed by varying the input metal price. This was done with both floating cone algorithms as well as early versions of the Lerchs-Grossmann (L-G) algorithm. This gave an indication of the pit sensitivity to price but since other variables also change, some with metal price (perhaps steel and equipment), and some independently (fuel and tires) the understanding of these different pits was restricted. In addition, a run of the program could take hours, making a detailed analysis of small changes unwieldy. The L-G algorithm was programmed by a variety of people and sold as part of commercial mining packages, however it was first and most successfully commercialized by Jeff Whittle in 1984. When Whittle’s 3-D™ was expanded to 4-D the parameterization of the economic inputs was considered and the ability to run a suite of “pit shells” became automatic. The competing NPV Scheduler™ program sold by DataMine™ offers similar pit shell analysis capabilities."

Jan 1, 2018